Although we don't support or enable CPU PWM with LPT/SPT based systems,
it may have been enabled prior to loading the driver. Disable the CPU
PWM on LPT/SPT backlight disable to avoid warnings on LCPLL disable.
The issue has been present on BDW since BDW enabling, but was recently
introduced on HSW with
commit 437b15b801
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Sep 4 16:55:13 2015 +0300
drm/i915: use pch backlight override on hsw too
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reference: http://mid.gmane.org/87y4frhwsn.fsf@yhuang-dev.intel.com
Reported-by: kernel test robot <ying.huang@intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1446033429-8006-1-git-send-email-jani.nikula@intel.com
i915 expects the OpRegion to be cached (i.e. not __iomem), so explicitly
map it with memremap rather than the implied cache setting of
acpi_os_ioremap().
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: intel-gfx@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: dri-devel@lists.freedesktop.org
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Latest VBT mentions which set of registers will be used for BLC,
as controller number field. Making use of this field in BXT
BLC implementation. Also, the registers are used in case control
pin indicates display DDI. Adding a check for this.
According to Bspec, BLC_PWM_*_2 uses the display utility pin for output.
To use backlight 2, enable the utility pin with mode = PWM
v2: Jani's review comments
addressed
- Add a prefix _ to BXT BLC registers definitions.
- Add "bxt only" comment for u8 controller
- Remove control_pin check for DDI controller
- Check for valid controller values
- Set pipe bits in UTIL_PIN_CTL
- Enable/Disable UTIL_PIN_CTL in enable/disable_backlight()
- If BLC 2 is used, read active_low_pwm from UTIL_PIN polarity
Satheesh's review comment addressed
- If UTIL PIN is already enabled, BIOS would have programmed it. No
need to disable and enable again.
v3: Jani's review comments
- add UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK
- Disable UTIL_PIN if controller 1 is used
- Mask out UTIL_PIN_PIPE_MASK and UTIL_PIN_MODE_MASK before enabling
UTIL_PIN
- check valid controller value in intel_bios.c
- add backlight.util_pin_active_low
- disable util pin before enabling
v4: Change for BXT-PO branch:
Stubbed unwanted definition which was existing before
because of DC6 patch.
UTIL_PIN_MODE_PWM (0x1b << 24)
v2: Fixed Jani's review comment.
v3: Split the backight PWM frequency programming into separate patch,
in cases BIOS doesn't initializes it.
v4: Starting afresh and not modifying existing state for backlight, as
per Jani's recommendation.
v5: Fixed Jani's review comment wrt util pin enable
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Sunil Kamath <sunil.kamath@intel.com>
Signed-off-by: Uma Shankar <uma.shankar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Previously we've relied on having basically one backlight and one
backlight type per platform. This is already a bit quirky with PMIC PWM
support on VLV/CHV platforms with MIPI DSI. In the foreseeable future
we'll have at least DPCD based backlight control on eDP and DCS command
based backlight control on MIPI DSI. Backlight is becoming more and more
connector specific, so reflect this fact by making the backlight control
hooks connector specific.
This enables further work to reuse generic backlight code in
intel_panel.c while adding more specific backlight code accessed via the
hooks.
Cc: Deepak M <m.deepak@intel.com>
Cc: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Yetunde Adebisi <yetundex.adebisi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make adjusted_mode const whereever we don't have to modify it. This only
covers cases when we have a local adjusted_mode variable, and doesn't
make any difference for cases where we just dereference
pipe_config->adjusted_mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The adjustead_mode crtc_ timings are what we will program into the hardware,
so it's those timings we should be looking practically everywhere.
The normal and crtc_ timings should differ only when stere doubling is
used. In that case the normal timings are the orignal non-doubled
timigns, and crtc_ timings are the doubled timings used by the hardware.
The only case where we continue to look at the normal timings is when we
pass the adjusted_mode to drm_match_{cea,hdmi}_mode() to find the VIC.
drm_edid keeps the modes aronund in the non-double form only, so it
needs the non-double timings to match against.
Done with sed
's/adjusted_mode->\([vhVH]\)/adjusted_mode->crtc_\1/g'
's/adjusted_mode->clock/adjusted_mode->crtc_clock/g'
with a manual s/VDisplay/vdisplay/ within the comment in intel_dvo.c
v2: Update due to intel_dsi.c changes
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rename the function argument to 'adjusted_mode' whenever the function
only ever gets passed the adjusted_mode.
v2: Update due to intel_dsi.c changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently everyone and their dog has their own favourite spelling
for vga_switcheroo. This makes it hard to grep dmesg for log entries
relating to vga_switcheroo. It also makes it hard to find related
source files in the tree.
vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fall back to VBT based backlight modulation frequency if it's not
set. Do not hard code.
This could be a problem if there is no VBT.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Normally we determine the backlight PWM modulation frequency (which we
also use as backlight max value) from the backlight registers at module
load time, expecting the registers have been initialized by the BIOS. If
this is not the case, we fail.
The VBT contains the backlight modulation frequency in Hz. Add platform
specific functions to convert the frequency in Hz to backlight PWM
modulation frequency, and use them to initialize the backlight when the
registers are not initialized by the BIOS.
v2: Fix SPT and VLV. Thanks to Clint for the VLV code.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently the difference between backlight control on HSW vs. BDW/SKL is
that on HSW we modify the duty cycle on the CPU register, and have the
hardware pass the changes on to the PCH registers. We still drive the
PCH PWM on both. While HSW and BDW use the same LPT PCH, BDW does not
pass these messages on to the PCH. Therefore on BDW we need to enable
the PCH override bit, and program the PCH directly. (On SPT PCH, this
mode is the default.) We could as well do this on HSW too, and in fact
I've been told this is what a certain other operating system does. So
use PCH backlight override on HSW too.
This simplifies some follow-up code, but it does have the danger of
breaking backlight on HSW machines. It should work, but mysterious are
the ways of backlight.
While at it, name the related backlight hooks according to the PCH
rather than the CPU for clarity.
Cc: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the CRC PWM device in intel_panel.c and add new MIPI backlight
specififc callbacks
v2: Modify to use pwm_config callback
v3: Addressed Jani's comments
- Renamed all function as pwm_* instead of vlv_*
- Call intel_panel_actually_set_backlight in enable function
- Return -ENODEV in case pwm_get fails
- in case pwm_config error return error cdoe from pwm_config
- Cleanup pwm in intel_panel_destroy_backlight
v4: Removed unused #defines and initialized backlight with INVALID_PIPE (Ville)
CC: Samuel Ortiz <sameo@linux.intel.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some 855gm models (at least ThinkPad X40) regressed because of
commit b0cd324fae
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 12 16:25:43 2014 +0200
drm/i915: don't save/restore backlight hist ctl registers
which tried to make our driver more robust by not blindly saving and
restoring registers, but it failed to take into account
commit 0eb96d6ed3
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Wed Oct 14 12:33:41 2009 -0700
drm/i915: save/restore BLC histogram control reg across suspend/resume
Fix the regression by enabling hist ctl on gen2.
v2: Improved the comment.
v3: Improved the comment, again.
Reported-and-tested-by: Philipp Gesang <phg@phi-gamma.net>
References: http://mid.gmane.org/20150623222648.GD12335@acheron
Fixes: b0cd324fae ("drm/i915: don't save/restore backlight hist ctl registers")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: stable@vger.kernel.org
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Enabling BLC on BXT.
Includes register definition, and new functions for BXT.
In BXT, there are 2 sets of registers for BLC. Until there is clarity
about which set would be effective, set 1 is being used.
This would have to be re-visited if there is any change or when 2 LFPs are
enabled on BXT.
This patch enables brightness change which would be effected by use of
hot-keys or sysfs entry.
TODO:- BLC implementation will have to re-visited when
1. there is clarity about which set of registers has to be used and when.
2. CDCLK frequency is changed
v2: Jani's review comments
- Modified comment in i915_reg.h
- Renamed register defintions
- Removed definition of duty cycle max. Not required now and its not 64-bit.
v3:
- Rebase on top of VLV/CHV backlight changes, in particuliar
bxt_set_backlight() now has a different prototype (Damien)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Shankar, Uma <uma.shankar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We have grown a number of different implementations of
DIV_ROUND_CLOSEST_ULL throughout the kernel. Move the i915 one to
kernel.h so that it can be reused.
Signed-off-by: Javi Merino <javi.merino@arm.com>
Reviewed-by: Jeff Epler <jepler@unpythonic.net>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Guenter Roeck <linux@roeck-us.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Alex Elder <elder@linaro.org>
Cc: Antti Palosaari <crope@iki.fi>
Cc: Javi Merino <javi.merino@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull drm updates from Dave Airlie:
"This is the main drm pull, it has a shared branch with some alsa
crossover but everything should be acked by relevant people.
New drivers:
- ATMEL HLCDC driver
- designware HDMI core support (used in multiple SoCs).
core:
- lots more atomic modesetting work, properties and atomic ioctl
(hidden under option)
- bridge rework allows support for Samsung exynos chromebooks to
work finally.
- some more panels supported
i915:
- atomic plane update support
- DSI uses shared DSI infrastructure
- Skylake basic support is all merged now
- component framework used for i915/snd-hda interactions
- write-combine cpu memory mappings
- engine init code refactored
- full ppgtt enabled where execlists are enabled.
- cherryview rps/gpu turbo and pipe CRC support.
radeon:
- indirect draw support for evergreen/cayman
- SMC and manual fan control for SI/CI
- Displayport audio support
amdkfd:
- SDMA usermode queue support
- replace suballocator usage with more suitable one
- rework for allowing interfacing to more than radeon
nouveau:
- major renaming in prep for later splitting work
- merge arm platform driver into nouveau
- GK20A reclocking support
msm:
- conversion to atomic modesetting
- YUV support for mdp4/5
- eDP support
- hw cursor for mdp5
tegra:
- conversion to atomic modesetting
- better suspend/resume support for child devices
rcar-du:
- interlaced support
imx:
- move to using dw_hdmi shared support
- mode_fixup support
sti:
- DVO support
- HDMI infoframe support
exynos:
- refactoring and cleanup, removed lots of internal unnecessary
abstraction
- exynos7 DECON display controller support
Along with the usual bunch of fixes, cleanups etc"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (724 commits)
drm/radeon: fix voltage setup on hawaii
drm/radeon/dp: Set EDP_CONFIGURATION_SET for bridge chips if necessary
drm/radeon: only enable kv/kb dpm interrupts once v3
drm/radeon: workaround for CP HW bug on CIK
drm/radeon: Don't try to enable write-combining without PAT
drm/radeon: use 0-255 rather than 0-100 for pwm fan range
drm/i915: Clamp efficient frequency to valid range
drm/i915: Really ignore long HPD pulses on eDP
drm/exynos: Add DECON driver
drm/i915: Correct the base value while updating LP_OUTPUT_HOLD in MIPI_PORT_CTRL
drm/i915: Insert a command barrier on BLT/BSD cache flushes
drm/i915: Drop vblank wait from intel_dp_link_down
drm/exynos: fix NULL pointer reference
drm/exynos: remove exynos_plane_dpms
drm/exynos: remove mode property of exynos crtc
drm/exynos: Remove exynos_plane_dpms() call with no effect
drm/i915: Squelch overzealous uncore reset WARN_ON
drm/i915: Take runtime pm reference on hangcheck_info
drm/i915: Correct the IOSF Dev_FN field for IOSF transfers
drm/exynos: fix DMA_ATTR_NO_KERNEL_MAPPING usage
...
The objective is to make this structure usable with the atomic helpers,
so let's start with the rename. Patch generated with coccinelle:
@@ @@
-struct intel_crtc_config {
+struct intel_crtc_state {
...
}
@@ @@
-struct intel_crtc_config
+struct intel_crtc_state
v2: Completely generate the patch with cocci. (Ander)
Signed-off-by: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit 6dda730e55
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jun 24 18:27:40 2014 +0300
drm/i915: respect the VBT minimum backlight brightness
introduced a bug which resulted in inconsistent brightness levels on
different machines. If a suspended was entered with the screen off some
machines would resume with the screen at minimum brightness and others
at maximum brightness.
The following commands can be used to produce this behavior.
xset dpms force off
sleep 1
sudo systemctl suspend
(resume ...)
The root cause of this problem is a comparison which checks to see if
the backlight level is zero when the panel is enabled. If it is zero,
it is set to the maximum level. Unfortunately, not all machines have a
minimum level of zero. On those machines the level is left at the
minimum instead of begin set to the maximum.
Fix the bug by updating the comparison to check for the minimum
backlight level instead of zero. Also, expand the comparison for
the possible case when the level is less than the minimum.
Fixes: 6dda730e55 ("respect the VBT minimum backlight brightness")
Signed-off-by: Jeremiah Mahler <jmmahler@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
So with all the code movement and extraction in intel_pm.c in -next
git is hopelessly confused with
commit 2208d655a9
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Nov 14 09:25:29 2014 +0100
drm/i915: drop WaSetupGtModeTdRowDispatch:snb
from -fixes. Worse even small changes in -next move around the
conflict context so rerere is equally useless. Let's just backmerge
and be done with it.
Conflicts:
drivers/gpu/drm/i915/i915_drv.c
drivers/gpu/drm/i915/intel_pm.c
Except for git getting lost no tricky conflicts really.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Now that the backlight device no longer gets registered too early we
should be able to drop most of the INVALID_PIPE checks from the backlight
code.
The only exceptio is the opregion stuff where we may (in theory at
least) get a request from the BIOS already during driver init as soon as
the backlight setup has been done. In which case we can still get the
INVALID_PIPE from intel_get_pipe_from_connector(). So leave that check
in place, and add a comment explaining why.
For the rest, if we still manage to get here with INVALID_PIPE on
VLV/CHV we will now get a WARN from the lower level functions and
can then actually investigate further.
v2: Leave the check in the BIOS related code (Jani)
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we register the backlight device as soon as we register the
connector. That means we can get backlight requests from userspace
already before reading out the current modeset hardware state.
That means we don't yet know the current crtc->encoder->connector mapping,
which causes problems for VLV/CHV which need to know the current pipe in
order to figure out which BLC registers to poke. Currently we just
ignore such requests fairly deep in the backlight code which means the
backlight device brightness property will get out of sync with our
backlight.level and the actual hardware state.
Fix the problem by delaying the backlight device registration until the
entire modeset init has been performed. And we also move the
backlight unregisteration to happen as the first thing during the
modeset cleanup so that we also won't be bothered with userspace
backlight requested during teardown.
This is a real world problem on machines using systemd, because systemd,
for some reason, wants to restore the backlight to the level it used last
time. And that happens as soon as it sees the backlight device appearing
in the system. Sometimes the userspace access makes it through before
the modeset init, sometimes not.
v2: Do not lie to the user in the debug prints (Jani)
Include connector name in the prints (Jani)
Fix a typo in the commit message (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV both pipes A and B have their own backlight control
registers. In order to correctly read out the current hardware state at
init we need to know which pipe is driving the eDP port. Pass that
information down from the eDP init code into the backlight code.
To determine the correct pipe we first look at which pipe is currently
configured in the port control register, if that look invalid we look
at which pipe's PPS is currently controlling the port, and if that
too looks invalid we just assume pipe A.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/CHV when the display is off, we can't read out the current
backlight level from the hardware since we have no pipe to do so.
Currently we end up reading a bigus register due to passing
INVALID_PIPE to VLV_BLC_PWM_CTL().
Skip the entire .get_backlight() call if the backlight isn't enabled
according to backlight.enabled.
This problem can be reproduced simply by reading the backlight device
actual_brightness file while the display is off.
Cc: Jani Nikula <jani.nikula@intel.com>
Suggested-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have backlight controls only on pipes A and B. Bail out
without touching registers that don't exist, and print a warning.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Never trust (your interpretation of) the VBT. Regression from
commit 6dda730e55
Author: Jani Nikula <jani.nikula@intel.com>
Date: Tue Jun 24 18:27:40 2014 +0300
drm/i915: respect the VBT minimum backlight brightness
causing div by zero if VBT minimum brightness equals maximum brightness.
Despite my attempts I've failed in my detective work to figure out what
the root cause is. This is not the real fix, but we have to do
something.
Reported-by: Mike Auty <mike.auty@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=86551
Cc: stable@vger.kernel.org (v3.17+)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
SPT is always in the PCH override mode, and the bit MBZ. Only set
override on LPT.
v2: check for PCH version (Ville)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
So I've sent the first pull request to Dave and I expect his request
for a merge tree any second now ;-)
More seriously I have some pending patches for 3.19 that depend upon
both trees, hence backmerge. Conflicts are all trivial.
Conflicts:
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/intel_display.c
v2: Of course I've forgotten the fixup script for the silent conflict.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Move the duplicated DIV_ROUND_CLOSEST_ULL macro into the intel_drv.h
header file so that it can be shared between intel_display.c
and intel_panel.c.
Signed-off-by: U. Artie Eoff <ullysses.a.eoff@intel.com>
Reviewed-By: Joe Konno <joe.konno@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Improper truncated integer division in the scale() function causes
actual_brightness != brightness. This (partial) work-around should be
sufficient for a majority of use-cases, but it is by no means a complete
solution.
TODO: Determine how best to scale "user" values to "hw" values, and
vice-versa, when the ranges are of different sizes. That would be a
buggy scenario even with this work-around.
The issue was introduced in the following (v3.17-rc1) commit:
6dda730 drm/i915: respect the VBT minimum backlight brightness
Note that for easier backporting this commit adds a duplicated macro.
A follow-up cleanup patch rectifies this for 3.18+
v2: (thanks to Chris Wilson) clarify commit message, use rounded division
macro
v3: -DIV_ROUND_CLOSEST() fails to build with CONFIG_X86_32=y. (Jani)
-Use DIV_ROUND_CLOSEST_ULL() instead. (Damien)
-v1 and v2 originally authored by Joe Konno.
Signed-off-by: U. Artie Eoff <ullysses.a.eoff@intel.com>
Cc: stable@vger.kernel.org
Reviewed-By: Joe Konno <joe.konno@intel.com>
[danvet: Add backporting note.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
SKL stage 1 patches still need polish so will likely miss the 3.18
merge window. We've decided to postpone to 3.19 so let's pull this in
to make patch merging and conflict handling easier.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Originally the irq safe spinlock was required because of asle
interrupts. But since
commit 91a60f2071
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Oct 31 18:55:48 2013 +0200
drm/i915: move opregion asle request handling to a work queue
there's no need for this any more. So switch to the simpler mutex.
v2: Cite the right commit, spotted by Jani.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
Chris has decided that enough is enough. It's time to fixup dev Vs
dev_priv. This is a modest contribution to the crusade.
v2: Still use INTEL_INFO(), for the (mythical!) case we want to hardcode
the info struct with defines (Chris)
Rename the macro argument from 'dev' to 'dev_priv' (Jani)
v3: Use names unlikely to be used as macro arguments (Chris)
Suggested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make backlight class sysfs brightness 0 value switch off the backlight
for connectors that have the backlight_power callback defined. For eDP,
this has the similar caveats regarding power savings as bl_power as only
the power sequencer backlight control is switched off.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Make backlight class sysfs bl_power a sub-state of backlight enabled, if
a backlight power connector callback is defined. It's up to the
connector callback to handle the sub-state, typically in a way that
respects panel power sequencing.
v2: Post the version that does not oops. *facepalm*.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Tested_by: Clinton Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BIOS or firmware can modify hardware state during suspend/resume,
for example on the Toshiba CB35 or Lenovo T400, so log a debug message
instead of a warning if the backlight is unexpectedly enabled.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=80930
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Historically we've exposed the full backlight PWM duty cycle range to
the userspace, in the name of "mechanism, not policy". However, it turns
out there are both panels and board designs where there is a minimum
duty cycle that is required for proper operation. The minimum duty cycle
is available in the VBT.
The backlight class sysfs interface does not make any promises to the
userspace about the physical meaning of the range
0..max_brightness. Specifically there is no guarantee that 0 means off;
indeed for acpi_backlight 0 usually is not off, but the minimum
acceptable value.
Respect the minimum backlight, and expose the range acceptable to the
hardware as 0..max_brightness to the userspace via the backlight class
device; 0 means the minimum acceptable enabled value. To switch off the
backlight, the user must disable the encoder.
As a side effect, make the backlight class device max brightness and
physical PWM modulation frequency (i.e. max duty cycle)
independent. This allows a follow-up patch to virtualize the max value
exposed to the userspace.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[danvet: s/BUG_ON/WARN_ON/]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This reverts commit 773875bfb6.
It is very much needed and the lack of dithering has been reported by
a large list of people with various gen2/3 hardware.
Also, the original patch was complete non-sense since the WARNING
backtraces in the references bugzilla are about
gmch_pfit.lvds_border_bits mismatch, not at all about the dither bit.
That one seems to work.
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
Cc: stable@vger.kernel.org
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
commit c675949ec5
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Apr 9 11:31:37 2014 +0300
drm/i915: do not setup backlight if not available according to VBT
caused a regression on machines with a misconfigured VBT. Add a quirk to
assert the presence of a controllable backlight. Use it to ignore the VBT
backlight presence check during backlight setup.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79813
Tested-by: James Duley <jagduley@gmail.com>
Tested-by: Michael Mullin <masmullin@gmail.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org # 3.15 only
[danvet: Add cc: stable because the regressing commit is in 3.15.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For reasons I can't claim to fully understand gen4 seems to require
backlight duty cycle setting after the backlight has been enabled, or
else black screen follows. I don't have documentation for the correct
sequence on gen4 either. Confirmed on Dell Latitude D630 and MacBook4,1.
This fixes a regression introduced by
commit b35684b8fa
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:13:41 2013 +0200
drm/i915: do full backlight setup at enable time
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=75791
Reported-and-tested-by: mcy@lm7.fr
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=79423
Reported-and-tested-by: Marc Milgram <mmilgram@redhat.com>
Cc: Stable <stable@vger.kernel.org> # 3.14+
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Merge drm-fixes into drm-next.
Both i915 and radeon need this done for later patches.
Conflicts:
drivers/gpu/drm/drm_crtc_helper.c
drivers/gpu/drm/i915/i915_drv.h
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/i915_gem_execbuffer.c
drivers/gpu/drm/i915/i915_gem_gtt.c
For atomic, it will be quite necessary to not need to care so much
about locking order. And 'state' gives us a convenient place to stash a
ww_ctx for any sort of update that needs to grab multiple crtc locks.
Because we will want to eventually make locking even more fine grained
(giving locks to planes, connectors, etc), split out drm_modeset_lock
and drm_modeset_acquire_ctx to track acquired locks.
Atomic will use this to keep track of which locks have been acquired
in a transaction.
v1: original
v2: remove a few things not needed until atomic, for now
v3: update for v3 of connection_mutex patch..
v4: squash in docbook
v5: doc tweaks/fixes
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
After the split-out of crtc locks from the big mode_config.mutex
there's still two major areas it protects:
- Various connector probe states, like connector->status, EDID
properties, probed mode lists and similar information.
- The links from connector->encoder and encoder->crtc and other
modeset-relevant connector state (e.g. properties which control the
panel fitter).
The later is used by modeset operations. But they don't really care
about the former since it's allowed to e.g. enable a disconnected VGA
output or with a mode not in the probed list.
Thus far this hasn't been a problem, but for the atomic modeset
conversion Rob Clark needs to convert all modeset relevant locks into
w/w locks. This is required because the order of acquisition is
determined by how userspace supplies the atomic modeset data. This has
run into troubles in the detect path since the i915 load detect code
needs _both_ protections offered by the mode_config.mutex: It updates
probe state and it needs to change the modeset configuration to enable
the temporary load detect pipe.
The big deal here is that for the probe/detect users of this lock a
plain mutex fits best, but for atomic modesets we really want a w/w
mutex. To fix this lets split out a new connection_mutex lock for the
modeset relevant parts.
For simplicity I've decided to only add one additional lock for all
connector/encoder links and modeset configuration states. We have
piles of different modeset objects in addition to those (like bridges
or panels), so adding per-object locks would be much more effort.
Also, we're guaranteed (at least for now) to do a full modeset if we
need to acquire this lock. Which means that fine-grained locking is
fairly irrelevant compared to the amount of time the full modeset will
take.
I've done a full audit, and there's just a few things that justify
special focus:
- Locking in drm_sysfs.c is almost completely absent. We should
sprinkle mode_config.connection_mutex over this file a bit, but
since it already lacks mode_config.mutex this patch wont make the
situation any worse. This is material for a follow-up patch.
- omap has a omap_framebuffer_flush function which walks the
connector->encoder->crtc links and is called from many contexts.
Some look like they don't acquire mode_config.mutex, so this is
already racy. Again fixing this is material for a separate patch.
- The radeon hot_plug function to retrain DP links looks at
connector->dpms. Currently this happens without any locking, so is
already racy. I think radeon_hotplug_work_func should gain
mutex_lock/unlock calls for the mode_config.connection_mutex.
- Same applies to i915's intel_dp_hot_plug. But again, this is already
racy.
- i915 load_detect code needs to acquire this lock. Which means the
w/w dance due to Rob's work will be nicely contained to _just_ this
function.
I've added fixme comments everywhere where it looks suspicious but in
the sysfs code. After a quick irc discussion with Dave Airlie it
sounds like the lack of locking in there is due to sysfs cleanup fun
at module unload.
v1: original (only compile tested)
v2: missing mutex_init(), etc (from Rob Clark)
v3: i915 needs more care in the conversion:
- Protect the edp pp logic with the connection_mutex.
- Use connection_mutex in the backlight code due to
get_pipe_from_connector.
- Use drm_modeset_lock_all in suspend/resume paths.
- Update lock checks in the overlay code.
Cc: Alex Deucher <alexdeucher@gmail.com>
Cc: Rob Clark <robdclark@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Somehow a few functions have been dropped in the middle of backlight
code. Move them around. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When we set backlight on behalf of ACPI opregion, we will convert the
backlight value in the 0-255 range defined in opregion to the actual
hardware level. Commit 22505b82a2 (drm/i915: avoid brightness overflow
when doing scale) is meant to fix the overflow problem when doing the
conversion, but it also caused a problem that the converted hardware
level doesn't quite represent the intended value: say user wants maximum
backlight level(255 in opregion's range), then we will calculate the
actual hardware level to be: level = freq / max * level, where freq is
the hardware's max backlight level(937 on an user's box), and max and
level are all 255. The converted value should be 937 but the above
calculation will yield 765.
To fix this issue, just use 64 bits to do the calculation to keep the
precision and avoid overflow at the same time.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=72491
Reported-by: Nico Schottelius <nico-bugzilla.kernel.org@schottelius.org>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
drm-intel-next-2014-04-16:
- vlv infoframe fixes from Jesse
- dsi/mipi fixes from Shobhit
- gen8 pageflip fixes for LRI/SRM from Damien
- cmd parser fixes from Brad Volkin
- some prep patches for CHV, DRRS, ...
- and tons of little things all over
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
drm-intel-next-2014-04-04:
- cmd parser for gen7 but only in enforcing and not yet granting mode - the
batch copying stuff is still missing. Also performance is a bit ... rough
(Brad Volkin + OACONTROL fix from Ken).
- deprecate UMS harder (i.e. CONFIG_BROKEN)
- interrupt rework from Paulo Zanoni
- runtime PM support for bdw and snb, again from Paulo
- a pile of refactorings from various people all over the place to prep for new
stuff (irq reworks, power domain polish, ...)
Conflicts:
drivers/gpu/drm/i915/i915_gem_context.c
Apparently we really only need this when the pfit is enabled, at least
I couldn't dicern any difference here. Furthermore the hacks we have
to reconstruct this bit is a bit glaring, and probably only works
because we can't move the lvds port to any other pipe than pipe B on
gen2/3.
So let's just rip this out.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=77137 (the LVDS
WARNING log, not the main "VGA can't be turned on" issue).
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some machines use an external EC for controlling the backlight. Info
about this is present in the VBT. Do not setup native backlight control
if no PWM backlight is available or supported according to VBT. The
acpi_backlight interface appears to work for the EC control.
In most cases there has been no harm done, but it looks like there are
machines out there that have both an EC and our PWM line connected to
the same wire. This, obviously, does not end well.
This should fix the regression caused by
commit bc0bb9fd1c
Author: Jani Nikula <jani.nikula@intel.com>
Date: Thu Nov 14 12:14:29 2013 +0200
drm/i915: remove QUIRK_NO_PCH_PWM_ENABLE
AFAICT the quirk removed by the above commit effectively resulted in
i915 not driving the backlight PWM output, thus not messing things up.
Additionally this should fix the regression caused by
commit fbc9fe1b4f
Author: Aaron Lu <aaron.lu@intel.com>
Date: Fri Oct 11 21:27:45 2013 +0800
ACPI / video: Do not register backlight if win8 and native interface exists
which left some machines without a functioning backlight interface.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76276
Reference: https://bugzilla.kernel.org/show_bug.cgi?id=47941
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=62281
CC: Aaron Lu <aaron.lu@intel.com>
CC: Eric Griffith <EGriffith92@gmail.com>
CC: Kent Baxley <kent.baxley@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Tested-by: Martin <bugs@mrvanes.com>
Tested-by: jrg.otte@gmail.com
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTJlUvAAoJEHm+PkMAQRiGOhYH/1I+Bc7N7Rjr6QQAtBIy0GPC
XMqSE/gpgxlvRneQbQsvTUlPnWRhgzLGendT9HFKawkaQ0UNuZdRVyBHGFmpuED8
RlbicVVuuEZabrxEnCd7UPvYvEyK5pLIFpCRs5B+ManB1qLki2Ar03ymH1NRxOde
edmPbSUFo2aONITrEBm7tqT3cShTmBaDGP/zU0TNDMNrpVVDbHZolSNu2z4xOTa5
GqAOEbluLQ6jP3yxWur/V3Lk3W7pB6TabfX4o6UZu0F3iFnJxRMIzHXrI3o4yLTj
HEwmB3npfc8DIUk4oik7RkN+aqxDcdg/rBLQD63+xxt6zCkP+0q16brC0R67qWE=
=n9Ml
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc7' into drm-next
Linux 3.14-rc7
Backmerge to help out Intel guys.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTHSaRAAoJEHm+PkMAQRiG7G8IAJHElwFDNSQE7Y9MmbicrAMG
kfjhBtBpTaVrJKQXegCNUwDaLLyC4oLIxDheW84oPXbrEGDLqPtBov/hrcFkHVr4
lh/ZYk02nYtcfpN0JnL/Yj2oKHVmBWs0vFlM7StSFsJCj10DoCVQQdmAJ8XODTPo
CXMapk+UikTX1TlIO8+B5toyl3R1OqPmW211UV1vQVLKy66hu+MKVN/V+/EyopL0
1jO81EDpaRaeIJh1/okcyUoIq9pqLkAWNpeQ7uyXZ+Sfivt9RXwLYKmAB3lP20Hc
ZMIIoHSCyYRFjxLlQvt02bA9nY4wTY7YN5kZ2kk65y7TFfhcGsCw1Sc69iyCoKs=
=CJcA
-----END PGP SIGNATURE-----
Merge tag 'v3.14-rc6' into drm-intel-next-queued
Linux 3.14-rc6
I need the hdmi/dvi-dual link fixes in 3.14 to avoid ugly conflicts
when merging Ville's new hdmi cloning support into my -next tree
Conflicts:
drivers/gpu/drm/i915/Makefile
drivers/gpu/drm/i915/intel_dp.c
Makefile cleanup conflicts with an acpi build fix, intel_dp.c is
trivial.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
i915gm and i945gm also seem to use and need the legacy combination mode
bit in BLC_PWM_CTL.
v2: Also do this for i915gm (Ville).
Reported-and-tested-by: Luis Ortega <luiorpe1@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=75001
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Instead of modifying intel_panel in lvds_init_connector/dsi_init/
edp_init_connector, making changes to move intel_panel->downclock_mode
initialization to intel_panel_init()
v2: Jani's review comments incorporated
Removed downclock_mode local variable in dsi_init and
edp_init_connector
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
With 20+ module parameters, I think referring to them via a struct
improves clarity over just having a bunch of globals. While at it, move
the parameter initialization and definitions into a new file
i915_params.c to reduce clutter in i915_drv.c.
Apart from the ill-named i915_enable_rc6, i915_enable_fbc and
i915_enable_ppgtt parameters, for which we lose the "i915_" prefix
internally, the module parameters now look the same both on the kernel
command line and in code. For example, "i915.modeset".
The downsides of the change are losing static on a couple of variables
and not having the initialization and module_param_named() right next to
each other. On the other hand, all module parameters are now defined in
one place at i915_params.c. Plus you can do this to find all module
parameter references:
$ git grep "i915\." -- drivers/gpu/drm/i915
v2:
- move the definitions into a new file
- s/i915_params/i915/
- make i915_try_reset i915.reset, for consistency
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was forgotten in
commit 565ee3897f
Author: Jani Nikula <jani.nikula@intel.com>
Date: Wed Nov 13 12:56:29 2013 +0200
drm/i915: do not save/restore backlight registers in KMS
Since the confusion was likely due to the duplicated definition for
this pci config register, let's unify that, too.
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
My 855gm doesn't register the intel backlight but it still ends up
calling the backlight code to enable/disable the backlight via the
LVDS code. This leads to some WARNs due to backlight.max being 0.
Let's have intel_panel_enable_backlight() and intel_panel_disable_backlight()
check whether there's a backlight present or not.
Also move the backlight.present check from asle_set_backlight() into
intel_panel_set_backlight() for some extra symmetry.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
These are needed when we cat the debugfs and sysfs files.
V2: - Rebase
V3: - Rebase
V4: - Rebase
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If one mode of a internal panel has more than one refresh rate, then a reduced
clock is found for the LFP (LVDS/eDP). This enables switching between low
and high frequency dynamically. Moving downclock calculation to intel_panel
so that it is common for LVDS and eDP.
Signed-off-by: Vandana Kannan <vandana.kannan@intel.com>
Signed-off-by: Pradeep Bhat <pradeep.bhat@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Merge the bdw changes into the backlight rework branch so that we can
adapt the new code for bdw, too. This is a bit a mess, but doing this
another way would have delayed the merging of the backlight
refactoring. Mea culpa.
As discussed with Jani on irc only do bdw-specific callbacks for the
set/get methods and bake in the only other special-case into the pch
enable function.
Conflicts:
drivers/gpu/drm/i915/intel_panel.c
v2: Don't enable the PWM too early for bdw (Jani).
v3: Create new bdw_ functions for setup and enable - the rules change
sufficiently imo with the switch from controlling the pwm from the cpu
to controlling it completel from the pch to warrant this.
v4: Rip out unused pipe variable in bdw_enable_backlight (0-day
builder).
Tested-by: Ben Widawsky <ben@bwidawsk.net> (on bdw)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
No longer needed. We now have fully cached max backlight values.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The quirk was added as what I'd say was a stopgap measure in
commit e85843bec6
Author: Kamal Mostafa <kamal@canonical.com>
Date: Fri Jul 19 15:02:01 2013 -0700
drm/i915: quirk no PCH_PWM_ENABLE for Dell XPS13 backlight
without really digging into what was going on.
Also, as mentioned in the related bug [1], having the quirk regressed
some of the machines it was supposed to fix to begin with, and there
were patches posted to disable the quirk on such machines [2]!
The fact is, we do need the BLM_PCH_PWM_ENABLE bit set to have
backlight. With the quirk, we've relied on BIOS to have set it, and our
save/restore code to retain it. With the full backlight setup at enable,
we have no place for things that rely on previous state.
With the per platform hooks, we've also made a change in the PCH
platform enable order: setting the backlight duty cycle between CPU and
PCH PWM enable. Some experimenting and
commit 770c12312a
Author: Takashi Iwai <tiwai@suse.de>
Date: Sat Aug 11 08:56:42 2012 +0200
drm/i915: Fix blank panel at reopening lid
indicate that we can't set the backlight before enabling CPU PWM; the
value just won't stick. But AFAICT we should do it before enabling the
PCH PWM.
Finally, any fallout we should fix properly, preferrably without quirks,
and absolutely without quirks that rely on existing state. With the per
platform hooks have much more flexibility to adjust the sequence as
required by platforms.
[1] https://bugzilla.kernel.org/show_bug.cgi?id=47941
[2] http://lkml.kernel.org/r/1378229848-29113-1-git-send-email-kamal@canonical.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We should now have all the information we need to do a full
initialization of the backlight registers.
v2: Keep QUIRK_NO_PCH_PWM_ENABLE for now (Imre).
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prior to Haswell the CPU control register for backlight
(BLC_PWM_CPU_CTL) toggled the PCH baclight pin for us. This made some
sense as there was no pin on the CPU. With Haswell came the introduction
of a CPU backlight pin, but the interface was still controlled by
software with the same mechnism. Behind the scenes, hardware did all the
dirty work for us.
Broadwell no longer provides this for free. If we want to use the PCH
backlight pin [1] then we have to set the override bit BLC_PWM_PCH_CTL1
and program BLC_PWM_PCH_CTL2 for the PWM values.
This patch implements that. This patch is compile tested only, and given
that I rarely if ever touch this code, careful review is welcome.
[1] According to Art, we know of no devices that exist which use the CPU
pin (and remember it has existed already on HSW). If such a device does
exist, we'll have to handle it properly - this is left as TODO until
then.
v2: Drop the abstraction prep patch, as a bigger backlight overhaul is
in the works, and do just the mimimal bdw enabling now. (by Jani)
CC: Art Runyan <arthur.j.runyan@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Prepare for being able to use the information at enable.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We now have the max backlight value cached. Use it.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This allows more flexibility in the ordering of the register writes, and
lets us drop level setting altogether as necessary on a per platform
basis.
For gen2-gen3, this is the only thing that happens in enable/disable.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It has per pipe registers.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Citing Jani's response to Imre's question in the review discussion:
> According to the gen2/3 bspec I have, the correct mask is
> BACKLIGHT_DUTY_CYCLE_MASK_PNV only in case of IS_PINEVIEW(dev), for
> everything else it's BACKLIGHT_DUTY_CYCLE_MASK.
What you say is correct, but we've treated all gen2/3 similar to PNV
since
commit ca88479c1c
Author: Keith Packard <keithp@keithp.com>
Date: Fri Nov 18 11:09:24 2011 -0800
drm/i915: Treat pre-gen4 backlight duty cycle value consistently
i.e. we only use the high 15 bits for all gen2/3. For non-PNV this just
means the lowest bit is always zero. For PNV the lowest bit has a
different meaning in both the PWM freq and duty cycle fields.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
[danvet: Make the commit message less empty.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The backlight code has grown rather hairy, not least because the
hardware registers and bits have repeatedly been shuffled around. And
this isn't expected to get any easier with new hardware. Make things
easier for our (read: my) poor brains, and split the code up into chip
specific functions.
There should be no functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
ALthough usually there's only one connector that supports backlight,
this also finds the correct connector. Before, we only updated the
connector on pipe A, which might not be the one with backlight. (This
only made a difference on BYT.)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Move from dev_priv to connector->panel. We still don't allow multiple
sysfs interfaces, though.
There should be no functional changes, except for a slight reordering of
connector backlight and sysfs destroy calls. (This change happens now
that the backlight device is actually per-connector, even though the
destroy calls became per-connector earlier.)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I've always felt the backlight device conditional build has been all
backwards. Make it feel right.
Gently move things towards connector based stuff while at it.
There should be no functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bit a bit -fixes pull request in the merge window than usual dua to two
feauture-y things:
- Display CRCs are now enabled on all platforms, including the odd DP case
on gm45/vlv. Since this is a testing-only feature it should ever hurt,
but I figured it'll help with regression-testing -fixes. So I left it
in and didn't postpone it to 3.14.
- Display power well refactoring from Imre. Would have caused major pain
conflict with the bdw stage 1 patches if I'd postpone this to -next.
It's only an relatively small interface rework, so shouldn't cause pain.
It's also been in my tree since almost 3 weeks already.
That accounts for about two thirds of the pull, otherwise just bugfixes:
- vlv backlight fix from Jesse/Jani
- vlv vblank timestamp fix from Jesse
- improved edp detection through vbt from Ville (fixes a vlv issue)
- eDP vdd fix from Paulo
- fixes for dvo lvds on i830M
- a few smaller things all over
Note: This contains a backmerge of v3.12. Since the -internal branch
always applied on top of -nightly I need that unified base to merge bdw
patches. So you'll get a conflict with radeon connector props when pulling
this (and nouveau/master will also conflict a bit when Ben doesn't
rebase). The backmerge itself only had conflicts in drm/i915.
There's also a tiny conflict between Jani's backlight fix and your sysfs
lifetime fix in drm-next.
* tag 'drm-intel-fixes-2013-11-07' of git://people.freedesktop.org/~danvet/drm-intel: (940 commits)
drm/i915/vlv: use per-pipe backlight controls v2
drm/i915: make backlight functions take a connector
drm/i915: move opregion asle request handling to a work queue
drm/i915/vlv: use PIPE_START_VBLANK interrupts on VLV
drm/i915: Make intel_dp_is_edp() less specific
drm/i915: Give names to the VBT child device type bits
drm/i915/vlv: enable HDA display audio for Valleyview2
drm/i915/dvo: call ->mode_set callback only when the port is running
drm/i915: avoid unclaimed registers when capturing the error state
drm/i915: Enable DP port CRC for the "auto" source on g4x/vlv
drm/i915: scramble reset support for DP port CRC on vlv
drm/i915: scramble reset support for DP port CRC on g4x
drm/i916: add "auto" pipe CRC source
...
Conflicts:
MAINTAINERS
drivers/gpu/drm/i915/intel_panel.c
drivers/gpu/drm/nouveau/core/subdev/mc/base.c
drivers/gpu/drm/radeon/atombios_encoders.c
drivers/gpu/drm/radeon/radeon_connectors.c
With the connector and pipe passed around, we can now set the backlight
on the right pipe on VLV/BYT.
v2: drop combination mode check for VLV (Jani)
add save/restore code for VLV backlight regs (Jani)
check for existing modulation freq when initializing backlight regs (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67245
Tested-by: Joe Konno <joe.konno@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
On VLV/BYT, backlight controls a per-pipe, so when adjusting the
backlight we need to pass the correct info. So make the externally
visible backlight functions take a connector argument, which can be used
internally to figure out the pipe backlight to adjust.
v2: make connector pipe lookup check for NULL crtc (Jani)
fixup connector check in ASLE code (Jani)
v3: make sure we take the mode config lock around lookups (Daniel)
v4: fix double unlock in panel_get_brightness (Daniel)
v5: push ASLE work into a work queue (Daniel)
v6: separate ASLE work to a prep patch, rebase (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
- CRC support from Damien and He Shuang. Long term this should allow us to
test an awful lot modesetting corner cases automatically. So for me as
the maintainer this is really big.
- HDMI audio fix from Jani.
- VLV dpll computation code refactoring from Ville.
- Fixups for the gpu booster from last time around (Chris).
- Some cleanups in the context code from Ben.
- More watermark work from Ville (we'll be getting there ...).
- vblank timestamp improvements from Ville.
- CONFIG_FB=n support, including drm core changes to make the fbdev
helpers optional.
- DP link training improvements (Jani).
- mmio vtable from Ben, prep work for future hw.
* tag 'drm-intel-next-2013-10-18' of git://people.freedesktop.org/~danvet/drm-intel: (132 commits)
drm/i915/dp: don't mention eDP bpp clamping if it doesn't affect bpp
drm/i915: remove dead code in ironlake_crtc_mode_set
drm/i915: crc support for hsw
drm/i915: fix CRC debugfs setup
drm/i915: wait one vblank when disabling CRCs
drm/i915: use ->get_vblank_counter for the crc frame counter
drm/i915: wire up CRC interrupt for ilk/snb
drm/i915: add CRC #defines for ilk/snb
drm/i915: extract display_pipe_crc_update
drm/i915: don't Oops in debugfs for I915_FBDEV=n
drm/i915: set HDMI pixel clock in audio configuration
drm/i915: pass mode to ELD write vfuncs
cpufreq: Add dummy cpufreq_cpu_get/put for CONFIG_CPU_FREQ=n
drm/i915: check gem bo size when creating framebuffers
drm/i915: Use unsigned long for obj->user_pin_count
drm/i915: prevent tiling changes on framebuffer backing storage
drm/i915: grab dev->struct_mutex around framebuffer_init
drm/i915: vlv: fix VGA hotplug after modeset
drm: add support for additional stereo 3D modes
drm/i915: preserve dispaly init order on ByT
...
So drm was abusing device lifetimes, by having embedded device structures
in the minor and connector it meant that the lifetime of the internal drm
objects (drm_minor and drm_connector) were tied to the lifetime of the device
files in sysfs, so if something kept those files opened the current code
would kfree the objects and things would go downhill from there.
Now in reality there is no need for these lifetimes to be so intertwined,
especailly with hotplugging of devices where we wish to remove the sysfs
and userspace facing pieces before we can unwind the internal objects due
to open userspace files or mmaps, so split the objects out so the struct
device is no longer embedded and do what fbdev does and just allocate
and remove the sysfs inodes separately.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Yet other direct usages of the pipe number instead of pipe_name().
We've been tracking them lately but managed to miss these last ones.
v2: Catch them all! (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
At the moment we have 3 paths that lead to actually_set_backlight(),
from modesetting, ACPI/OpRegion requests and our very own
intel_backlight interface, and we have no way of distinguishing them in
the debug log. So add a debug breadcrumb to explain the source of the
backlight changes.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Still digging up the actual VBT info for this, but wanted to get this
out there for testing, or in case others are also bugged by this.
This can happen if you boot with an external display connected. In that
case, the attached eDP backlight modulation frequency may not be
programmed, so we need to use something (in this case the value my BIOS
normally programs with just the internal display enabled).
v2: fix masking and magic value in read_blc_pwm_ctl (Jani)
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=67732
Tested-by: shui yangwei <yangweix.shui@intel.com> (v1)
Reviewed-by: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Not valid for later non-PCH split platforms such as VLV.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSQMORAAoJEHm+PkMAQRiGj14H/1bjhtfNjPdX7MVQAzA+WpwX
s7h1IQu2Si9S5S1lBiM2sBTOssVcmfheO9x4yqm7JNOD1RnssWKOM3q+zVOLstwd
GD3gluJPeraD5EyYSqEJ9ILPQ3gbxb4wOlT0Z291TW6E8XhLRr0RTOJPksRsgvLH
Ckm9uJh6ArS6ZXfXiaDQfd+xHAQJkUfW6nMSA0g9ZO9C6KIDRvcbUmrY3m4HhfIk
mK0TXCBs+AXGDIjTEB8JgIQL/5y1Qn0c4R+2uTU/4YWwyLvJTV1e44kGoleukMMT
6Pw/TNlUEN161dbSaqCyF3sfXHDYQ5valycI2PDgitMtPSxbzsU1VDizS8+daRg=
=lEmF
-----END PGP SIGNATURE-----
Merge tag 'v3.12-rc2' into drm-intel-next
Backmerge Linux 3.12-rc2 to prep for a bunch of -next patches:
- Header cleanup in intel_drv.h, both changed in -fixes and my current
-next pile.
- Cursor handling cleanup for -next which depends upon the cursor
handling fix merged into -rc2.
All just trivial conflicts of the "changed adjacent lines" type:
drivers/gpu/drm/i915/i915_gem.c
drivers/gpu/drm/i915/intel_display.c
drivers/gpu/drm/i915/intel_drv.h
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Ville and I were wondering why his laptop was missing the
intel_backlight sysfs interface. Turns out we never register it when
CONFIG_BACKLIGHT_CLASS_DEVICE=m. This has been broken ever since the
i915 native backlight interface was added.
CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Especially intel_gmch_panel_fitting was shifting way too much over the
right edge and also was way too long. So extract two helpers, one for
gen4+ and one for gen2/3. Now the entire thing is again almost
readable ...
Spurred by checkpatch freaking out about a Ville's pipeconfig rework
in intel_panel.c
Otherwise just two lines that needed appropriate breaking.
Not functional change in this patch.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rather that mess about with hdisplay/vdisplay from requested_mode, add
explicit pipe src size information to pipe config.
Now requested_mode is only really relevant for dvo/sdvo output timings.
For everything else either adjusted_mode or pipe src size should be
used.
In many places where we end up using pipe source size, we should
actually use the primary plane size, but we don't currently store
that information explicitly. As long as we treat primaries as full
screen only, we can get away with this. Eventually when we move
primaries over to drm_plane, we need to fix it all up.
v2: Add a comment to explain what pipe_src_{w,h} are
Add a note about primary planes to commit message
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Detangle the additional state of whether or not the hw has the pfit
enabled from whether it has zero size. This allows us to cleanly
distinguish in the code when we expect the pfit to be enabled (for
Haswell pc8), and when the BIOS is confused and needs sanitizing.
Reported-by: shui yanwei <yangweix.shui@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=68251
Tested-by: shui yanwei <yangweix.shui@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
intel_fixed_panel_mode() overwrote the adjusted_mode with the fixed mode
only partially. Notably it forgot to copy over the sync flags. The LVDS code however programmed the hardware with the sync flags from fixed mode, and then later the pipe config comparison obviously failed as we
filled out the adjusted_mode in get_config from the real registers.
Just call drm_mode_copy() in intel_fixed_panel_mode() to copy over the
whole thing, and then just use adjusted_mode in the LVDS code to figure
out which sync settings the hardware needs.
Also constify the fixed_mode argument to intel_fixed_panel_mode().
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If need to enable the panel fitter, the crtc timings have to be
programmed according to the panel's native (fixed) mode. This isn't the
case atm, since after the encoder changes adjusted_mode to fixed
mode the crtc_* timing fields of adjusted_mode will stay at their original
non-native values that the user passed in. This results in a corrupted
output.
One exception is when we have a second pass of computing encoder configs
due to bandwidth limitation, since then we'll set adjusted_mode.crtc_*
fields to the fixed mode values set in the first pass; so in this case
things will work out.
Fix this by updating the adjusted_mode.crtc_* fields when we set the
fixed panel mode.
This regression has been introduced in
commit 135c81b8c3
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun Jul 21 21:37:09 2013 +0200
drm/i915: clean up crtc timings computation
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Alex writes:
This is the radeon drm-next request. Big changes include:
- support for dpm on CIK parts
- support for ASPM on CIK parts
- support for berlin GPUs
- major ring handling cleanup
- remove the old 3D blit code for bo moves in favor of CP DMA or sDMA
- lots of bug fixes
[airlied: fix up a bunch of conflicts from drm_order removal]
* 'drm-next-3.12' of git://people.freedesktop.org/~agd5f/linux: (898 commits)
drm/radeon/dpm: make sure dc performance level limits are valid (CI)
drm/radeon/dpm: make sure dc performance level limits are valid (BTC-SI) (v2)
drm/radeon: gcc fixes for extended dpm tables
drm/radeon: gcc fixes for kb/kv dpm
drm/radeon: gcc fixes for ci dpm
drm/radeon: gcc fixes for si dpm
drm/radeon: gcc fixes for ni dpm
drm/radeon: gcc fixes for trinity dpm
drm/radeon: gcc fixes for sumo dpm
drm/radeonn: gcc fixes for rv7xx/eg/btc dpm
drm/radeon: gcc fixes for rv6xx dpm
drm/radeon: gcc fixes for radeon_atombios.c
drm/radeon: enable UVD interrupts on CIK
drm/radeon: fix init ordering for r600+
drm/radeon/dpm: only need to reprogram uvd if uvd pg is enabled
drm/radeon: check the return value of uvd_v1_0_start in uvd_v1_0_init
drm/radeon: split out radeon_uvd_resume from uvd_v4_2_resume
radeon kms: fix uninitialised hotplug work usage in r100_irq_process()
drm/radeon/audio: set up the sads on DCE3.2 asics
drm/radeon: fix handling of variable sized arrays for router objects
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/i915_gem_dmabuf.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/radeon/cik.c
drivers/gpu/drm/radeon/ni.c
drivers/gpu/drm/radeon/r600.c
On muxed systems, the other vgaswitcheroo client may depend on i915 to
handle the backlight. We began switching off the backlight since
commit a261b246eb
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jul 26 19:21:47 2012 +0200
drm/i915: disable all crtcs at suspend time
breaking backlight on discreet graphics in (some) muxed systems.
Keep the backlight on when the state is changed through vgaswitcheroo.
Note: The alternative would be to add a quirk table to achieve the same
based on system identifiers, but AFAICS it would asymptotically approach
effectively the same as this patch as more IDs are added, but with the
maintenance burden of the quirk table.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=55311
Tested-by: Fede <fedevx@yahoo.com>
Tested-by: Aximab <laurent.debian@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=59785
Tested-by: sfievet <sebastien.fievet@free.fr>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Some card's max brightness level is pretty large, e.g. on Acer Aspire
4732Z, the max level is 989910. If user space set a large enough level
then the current scale done in intel_panel_set_backlight will cause an
integer overflow and the scaled level will be mistakenly small, leaving
user with an almost black screen. This patch fixes this problem.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
[danvet: Add a comment to explain what's going on.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In the old days of the crtc helpers we've only had the encoder and
crtc ->mode_fixup callbacks. So when the lvds connector wanted to
adjust the crtc timings it had to set a driver-private mode flag to
tell the crtc mode fixup code to not overwrite them with the generic
ones.
When converting things to the new infrastructure I've kept the entire
logic and only moved the flag to pipe_config->timings_set. But this
logic is pretty tricky and already caused regressions:
commit 21d8a4756a
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Jul 12 08:07:30 2013 +0200
drm/i915: fix pfit regression for non-autoscaled resolutions
So take advantage of the flexibility our own modeset infrastructure
affords us and prefill default crtc timings. This allows us to rip out
->timings_set. Note that we overwrite things again when retrying the
pipe config computation due to bandwidth constraints to avoid bogus
crtc timings if the encoder only does relative adjustments (which is
how the pfit code works). Only a theoretical concern though since
platforms where we retry (pch-split platforms) do not need
adjustements (since only the old gmch pfit needs that). But let's
better be safe than sorry.
Since we now initialize the crtc timings before calling the
encoder->compute_config functions the crtc initialization in the gmch
pfit code is now redudant and so can be removed.
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@gmail.com>
[danvet: Add a paragraph to the commit message to explain why we can
ditch the crtc timings initialization call from the gmch pfit code, to
answer a question from Rodrigo's review.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=47941
BugLink: https://bugs.launchpad.net/bugs/1163720
BugLink: https://bugs.launchpad.net/bugs/1162026
Some machines suffer from non-functional backlight controls if
BLM_PCH_PWM_ENABLE is set, so provide a quirk to avoid doing so.
Apply this quirk to Dell XPS 13 models.
Tested-by: Eric Griffith <EGriffith92@gmail.com>
Tested-by: Kent Baxley <kent.baxley@canonical.com>
Cc: <stable@vger.kernel.org> # v3.8+
Signed-off-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
I.e. for letter/pillarboxing. For those cases we need to adjust the
mode a bit, but Jesse gmch pfit refactoring in
commit 2dd24552ca
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date: Thu Apr 25 12:55:01 2013 -0700
drm/i915: factor out GMCH panel fitting code and use for eDP v3
broke that by reordering the computation of the gmch pfit state with
the block of code that prepared the adjusted mode for it and told the
modeset core not to overwrite the adjusted mode with default settings.
We might want to switch around the core code to just fill in defaults,
but this code predates the pipe_config modeset rework. And in the old
crtc helpers we did not have a suitable spot to do this.
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Hans de Bruin <jmdebruin@xmsnet.nl>
Reported-and-tested-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
WARN_ON(!spin_is_locked()) is not a good idea on a UP system w/o
spinlock debugging. Use WARN_ON_SMP() instead.
This check has been added in
commit 8ba2d18520
Author: Jani Nikula <jani.nikula@intel.com>
Date: Fri Apr 12 15:18:37 2013 +0300
drm/i915: protect backlight registers and data with a spinlock
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This was still required a bit (on the cargo-cult side though) when the
state was stored in dev_priv, and when the enable/disable sequence was
botched a bit (to avoid too many updates).
But with pipeconfig we always get a clean slate, so this is pointless.
Rip it out.
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
