The documentation says that SGMII_LN_UCDR_SO_GAIN_MODE0 should be
set to 0, not 6, on the Qualcomm Technologies QDF2432.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changing the interrupt trigger region id to 2 and the
corresponding threshold set0/set1 values to 8/16.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since ethernet v1 hardware has a bug related to coalescing, disabling
this feature.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Toan Le <toanle@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current bgmac code initializes some DMA settings in the receive control
register for some hardware and then immediately clears those settings.
Not clearing those settings results in ~420Mbps *improvement* in
throughput; this system can now receive frames at line-rate on Broadcom
5871x hardware compared to ~520Mbps today. I also tested a few other
values but found there to be no discernible difference in CPU
utilization even if burst size and prefetching values are different.
On the hardware tested there was no need to keep the code that cleared
all but bits 16-17, but since there is a wide variety of hardware that
used this driver (I did not look at all hardware docs for hardware using
this IP block), I find it wise to move this call up and clear bits just
after reading the default value from the hardware rather than completely
removing it.
This is a good candidate for -stable >=3.14 since that is when the code
that was supposed to improve performance (but did not) was introduced.
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Fixes: 56ceecde1f ("bgmac: initialize the DMA controller of core...")
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the device, a MID entry represents a group of local ports, which can
later be bound to a MDB entry.
The lookup of an existing MID entry is currently done using the provided
MC MAC address and VID, from the Linux bridge. However, this can result
in an incorrect reuse of the same MID index in different VLAN-unaware
bridges (same IP MC group and VID 0).
Fix this by performing the lookup based on FID instead of VID, which is
unique across different bridges.
Fixes: 3a49b4fde2 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Elad Raz <eladr@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an interface is configured to use Tx/Rx-only queues,
the length of the statistics would be shortened to accomodate only the
statistics required per-each queue, and the values would be provided
accordingly.
However, the strings provided would still contain both Tx and Rx strings
for each one of the queues [regardless of its configuration], which might
lead to out-of-bound access when filling the buffers as well as incorrect
statistics presented.
Fixes: 9a4d7e86ac ("qede: Add support for Tx/Rx-only queues.")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
"Lots of fixes, mostly drivers as is usually the case.
1) Don't treat zero DMA address as invalid in vmxnet3, from Alexey
Khoroshilov.
2) Fix element timeouts in netfilter's nft_dynset, from Anders K.
Pedersen.
3) Don't put aead_req crypto struct on the stack in mac80211, from
Ard Biesheuvel.
4) Several uninitialized variable warning fixes from Arnd Bergmann.
5) Fix memory leak in cxgb4, from Colin Ian King.
6) Fix bpf handling of VLAN header push/pop, from Daniel Borkmann.
7) Several VRF semantic fixes from David Ahern.
8) Set skb->protocol properly in ip6_tnl_xmit(), from Eli Cooper.
9) Socket needs to be locked in udp_disconnect(), from Eric Dumazet.
10) Div-by-zero on 32-bit fix in mlx4 driver, from Eugenia Emantayev.
11) Fix stale link state during failover in NCSCI driver, from Gavin
Shan.
12) Fix netdev lower adjacency list traversal, from Ido Schimmel.
13) Propvide proper handle when emitting notifications of filter
deletes, from Jamal Hadi Salim.
14) Memory leaks and big-endian issues in rtl8xxxu, from Jes Sorensen.
15) Fix DESYNC_FACTOR handling in ipv6, from Jiri Bohac.
16) Several routing offload fixes in mlxsw driver, from Jiri Pirko.
17) Fix broadcast sync problem in TIPC, from Jon Paul Maloy.
18) Validate chunk len before using it in SCTP, from Marcelo Ricardo
Leitner.
19) Revert a netns locking change that causes regressions, from Paul
Moore.
20) Add recursion limit to GRO handling, from Sabrina Dubroca.
21) GFP_KERNEL in irq context fix in ibmvnic, from Thomas Falcon.
22) Avoid accessing stale vxlan/geneve socket in data path, from
Pravin Shelar"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (189 commits)
geneve: avoid using stale geneve socket.
vxlan: avoid using stale vxlan socket.
qede: Fix out-of-bound fastpath memory access
net: phy: dp83848: add dp83822 PHY support
enic: fix rq disable
tipc: fix broadcast link synchronization problem
ibmvnic: Fix missing brackets in init_sub_crq_irqs
ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context
Revert "ibmvnic: Fix releasing of sub-CRQ IRQs in interrupt context"
arch/powerpc: Update parameters for csum_tcpudp_magic & csum_tcpudp_nofold
net/mlx4_en: Save slave ethtool stats command
net/mlx4_en: Fix potential deadlock in port statistics flow
net/mlx4: Fix firmware command timeout during interrupt test
net/mlx4_core: Do not access comm channel if it has not yet been initialized
net/mlx4_en: Fix panic during reboot
net/mlx4_en: Process all completions in RX rings after port goes up
net/mlx4_en: Resolve dividing by zero in 32-bit system
net/mlx4_core: Change the default value of enable_qos
net/mlx4_core: Avoid setting ports to auto when only one port type is supported
net/mlx4_core: Fix the resource-type enum in res tracker to conform to FW spec
...
Driver allocates a shadow array for transmitted SKBs with X entries;
That means valid indices are {0,...,X - 1}. [X == 8191]
Problem is the driver also uses X as a mask for a
producer/consumer in order to choose the right entry in the
array which allows access to entry X which is out of bounds.
To fix this, simply allocate X + 1 entries in the shadow array.
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When MTU is changed from 9000 to 1500 while there is burst of inbound 9000
bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes
buffers. This causes memory corruption and sometimes crash.
This is because of a race condition in adaptor between "RQ disable"
clearing descriptor mini-cache and mini-cache valid bit being set by
completion of descriptor fetch. This can result in stale RQ desc being
cached and used when packets arrive. In this case, the stale descriptor
have old MTU value.
Solution is to write RQ->disable twice. The first write will stop any
further desc fetches, allowing the second disable to clear the mini-cache
valid bit without danger of a race.
Also, the check for rq->running becoming 0 after writing rq->enable to 0
is not done properly. When incoming packets are flooding the interface,
rq->running will pulse high for each dropped packet. Since the driver was
waiting for 10us between each poll, it is possible to see rq->running = 1
1000 times in a row, even though it is not actually stuck running.
This results in false failure of vnic_rq_disable(). Fix is to try more
than 1000 time without delay between polls to ensure we do not miss when
running goes low.
In old adaptors rq->enable needs to be re-written to 0 when posted_index
is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2016-10-27
This series contains fixes to ixgbe and i40e.
Emil fixes a NULL pointer dereference when a macvlan interface is brought
up while the PF is still down.
David root caused the original panic that was fixed by commit id
(a036244c06 "i40e: Fix kernel panic on enable/disable LLDP") and the
fix was not quite correct, so removed the get_default_tc() and replaced
it with a #define since there is only one TC supported as a default.
Guilherme Piccoli fixes an issue where if we modprobe the driver module
without enough MSI-X interrupts, then unload the module and reload it
again, the kernel would crash. So if we fail to allocate enough MSI-X
interrupts, we should disable them since they were previously enabled.
Huaibin Wang found that the order of the arguments for
ndo_dflt_bridge_getlink() were in the correct order, so fix the order.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Following the previous patch, as an optimization, the slave will
not even bother sending the DUMP_ETH_STATS command over the
comm channel.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_en_DUMP_ETH_STATS took the *counter mutex* and then
called the FW command, with WRAPPED attribute. As a result, the fw command
is wrapped on the Hypervisor when it calls mlx4_en_DUMP_ETH_STATS.
The FW command wrapper flow on the hypervisor takes the *slave_cmd_mutex*
during processing.
At the same time, a VF could be in the process of coming up, and could
call mlx4_QUERY_FUNC_CAP. On the hypervisor, the command flow takes the
*slave_cmd_mutex*, then executes mlx4_QUERY_FUNC_CAP_wrapper.
mlx4_QUERY_FUNC_CAP wrapper calls mlx4_get_default_counter_index(),
which takes the *counter mutex*. DEADLOCK.
The fix is that the DUMP_ETH_STATS fw command should be called with
the NATIVE attribute, so that on the hypervisor, this command does not
enter the wrapper flow.
Since the Hypervisor no longer goes through the wrapper code, we also
simply return 0 in mlx4_DUMP_ETH_STATS_wrapper (i.e.the function succeeds,
but the returned data will be all zeroes).
No need to test if it is the Hypervisor going through the wrapper.
Fixes: f9baff509f ("mlx4_core: Add "native" argument to mlx4_cmd ...")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently interrupt test that is part of ethtool selftest runs the
check over all interrupt vectors of the device.
In mlx4_en package part of interrupt vectors are uninitialized since
mlx4_ib doesn't exist. This causes NOP FW command to time out.
Change logic to test current port interrupt vectors only.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the Hypervisor, there are several FW commands which are invoked
before the comm channel is initialized (in mlx4_multi_func_init).
These include MOD_STAT_CONFIG, QUERY_DEV_CAP, INIT_HCA, and others.
If any of these commands fails, say with a timeout, the Hypervisor
driver enters the internal error reset flow. In this flow, the driver
attempts to notify all slaves via the comm channel that an internal error
has occurred.
Since the comm channel has not yet been initialized (i.e., mapped via
ioremap), this will cause dereferencing a NULL pointer.
To fix this, do not access the comm channel in the internal error flow
if it has not yet been initialized.
Fixes: 55ad359225 ("net/mlx4_core: Enable device recovery flow with SRIOV")
Fixes: ab9c17a009 ("mlx4_core: Modify driver initialization flow to accommodate SRIOV for Ethernet")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a kernel panic that occurs as a result of an asynchronous event
handled in roce_gid_mgmt:
mlx4_en_get_drvinfo is called and accesses freed resources.
This happens in a shutdown flow only, since pci device is destroyed
while netdevice is still alive.
Fixes: c27a02cd94 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is a race between incoming traffic and
initialization flow. HW is able to receive the packets
after INIT_PORT is done and unicast steering is configured.
Before we set priv->port_up NAPI is not scheduled and
receive queues become full. Therefore we never get
new interrupts about the completions.
This issue could happen if running heavy traffic during
bringing port up.
The resolution is to schedule NAPI once port_up is set.
If receive queues were full this will process all cqes
and release them.
Fixes: c27a02cd94 ("mlx4_en: Add driver for Mellanox ConnectX 10GbE NIC")
Signed-off-by: Erez Shitrit <erezsh@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing roundup_pow_of_two for large enough number with
bit 31, an overflow will occur and a value equal to 1 will
be returned. In this case 1 will be subtracted from the return
value and division by zero will be reached.
Fixes: 31c128b66e ("net/mlx4_en: Choose time-stamping shift value according to HW frequency")
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the default status of quality of service back to disabled,
as it hurts performance in some cases.
Fixes: 38438f7c7e ("net/mlx4: Set enhanced QoS support by default when ...")
Signed-off-by: Moshe Lazer <moshel@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When only one port type is supported, it should be read only.
We reject changing requests, even to the auto sense mode.
Fixes: 27bf91d6a0 ("mlx4_core: Add link type autosensing")
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The resource type enum in the resource tracker was incorrect.
RES_EQ was put in the position of RES_NPORT_ID (a FC resource).
Since the remaining resources maintain their current values,
and RES_EQ is not passed from slaves to the hypervisor in any
FW command, this change affects only the hypervisor.
Therefore, there is no backwards-compatibility issue.
Fixes: 623ed84b1f ("mlx4_core: initial header-file changes for SRIOV support")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Schedule these XPORT event tasks in the shared workqueue
so that IRQs are not freed in an interrupt context when
sub-CRQs are released.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MAC is capable of RGMII mode and that is probably a more typical
connection type than GMII today (eg it is used by Marvell Reference
designs for several SOCs). Let DT users specify the standard
phy-connection-type = "rgmii-id";
On a phy node.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to release resources properly in error handling path of
alloc_uld_rxqs(), This patch also removes unwanted arguments
and avoids calling the same function twice.
Fixes: 94cdb8bb99 (cxgb4: Add support for dynamic allocation
of resources for ULD
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is an old warning about mlx4_SW2HW_EQ_wrapper on x86:
ethernet/mellanox/mlx4/resource_tracker.c: In function ‘mlx4_SW2HW_EQ_wrapper’:
ethernet/mellanox/mlx4/resource_tracker.c:3071:10: error: ‘eq’ may be used uninitialized in this function [-Werror=maybe-uninitialized]
The problem here is that gcc won't track the state of the variable
across a spin_unlock. Moving the assignment out of the lock is
safe here and avoids the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the firmware can't work with a page with dma address 0.
Passing such an address to the firmware will cause the give_pages
command to fail.
To avoid this, in case we get a 0 dma address of a page from the
dma engine, we avoid passing it to FW by remapping to get an address
other than 0.
Fixes: bf0bf77f65 ('mlx5: Support communicating arbitrary host...')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case that the kernel PCI error handlers are not called, we will
trigger our own recovery flow.
The health work will give priority to the kernel pci error handlers to
recover the PCI by waiting for a small period, if the pci error handlers
are not triggered the manual recovery flow will be executed.
We don't save pci state in case of manual recovery because it will ruin the
pci configuration space and we will lose dma sync.
Fixes: 89d44f0a6c ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently there is a race between the health care work and the kernel
pci error handlers because both of them detect the error, the first one
to be called will do the error handling.
There is a chance that health care will disable the pci after resuming
pci slot.
Also create a separate WQ because now we will have two types of health
works, one for the error detection and one for the recovery.
Fixes: 89d44f0a6c ('net/mlx5_core: Add pci error handlers to mlx5_core driver')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The health sick status should be cleared when we start the health poll.
This is crucial for driver reload (unload + load) in order to behave
right in case of health issue.
Fixes: fd76ee4da5 ('net/mlx5_core: Fix internal error detection conditions')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ingress/Egress ACL enable function may fail and it should return
status to its caller to avoid NULL pointer dereference.
Fixes: f942380c12 ('net/mlx5: E-Switch, Vport ingress/egress ACLs rules for spoofchk')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Detaching the netdev before unregistering it cause some netdev cleanup
ndos to fail because they check presence of the netdev, so we need to
unregister the netdev first.
Fixes: 26e59d8077 ('net/mlx5e: Implement mlx5e interface attach/detach callbacks')
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of predicting the index of the wanted LRO timeout value from
hardware capabilities, look for the nearest LRO timeout value.
Fixes: 5c50368f38 ('net/mlx5e: Light-weight netdev open/stop')
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Mohamad Haj Yahia <mohamad@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, last use timestamp is initialized to zero.
This is not the expected value by higher layers such as
when we do TC action offloading. To fix that, set it to
the current time, e.g when the counter/rule is offloaded.
This is the same behaviour of non-offloaded TC actions.
Fixes: 43a335e055 ('mlx5_core: Flow counters infrastructure')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Autogroups groups num is increased when creating a new flow group,
but is never decreased.
Now decreasing it when deleting a flow group.
Fixes: f0d22d1874 ('net/mlx5_core: Introduce flow steering autogrouped flow table')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finding a new autogroup range is done by going over a group list
sorted by each group start index. The search is stopped after finding
the first free range. Adding the newly created group to the list is
wrongly added to the end of the list regardless of its start index as
the parameter of where to insert it is ignored.
This commit makes sure to use that unused parameter to insert
it where requested.
Fixes: f0d22d1874 ('net/mlx5_core: Introduce flow steering autogrouped flow table')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Always query the HCA caps after setting them to update the capablities
data structures. Not doing so results in incorrect capabilities being
reported including max_dc, max_qp and several others.
Fixes: 59211bd3b6 ("net/mlx5: Split the load/unload flow into hardware
and software flows")
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ARM 64B cache line systems have L1_CACHE_BYTES set to 128.
cache_line_size() will return the correct size.
Fixes: cf50b5efa2fe('net/mlx5_core/ib: New device capabilities
handling.')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only trees which are in use should be compared to requested prefix usage.
Fixes: 53342023ee ("mlxsw: spectrum_router: Implement LPM trees management")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the prefix bitlist is not saved for LPM trees, causing the
compare to always fail which causes the tree to be destroyed and created
for every inserted and removed FIB entry. So fix this by saving
the bitlist as it should have been done from the very beginning.
Fixes: 53342023ee ("mlxsw: spectrum_router: Implement LPM trees management")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Order of arguments is wrong.
The wrong code has been introduced by commit 7d4f8d871a, but is compiled
only since commit 9df70b6641.
Note that this may break netlink dumps.
Fixes: 9df70b6641 ("i40e: Remove incorrect #ifdef's")
Fixes: 7d4f8d871a ("switchdev; add VLAN support for port's bridge_getlink")
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: Huaibin Wang <huaibin.wang@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If we fail on allocating enough MSI-X interrupts, we should disable
them since they were previously enabled in this point of code.
Not disabling them can lead to WARN_ON() being triggered and subsequent
failure in enabling MSI as a fallback; the below message was shown without
this patch while we played with interrupt allocation in i40e driver:
[ 21.461346] sysfs: cannot create duplicate filename '/devices/pci0007:00/0007:00:00.0/0007:01:00.3/msi_irqs'
[ 21.461459] ------------[ cut here ]------------
[ 21.461514] WARNING: CPU: 64 PID: 1155 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x88/0xc0
Also, we noticed that without this patch, if we modprobe the module without
enough MSI-X interrupts (triggering the above warning), unload the module
and re-load it again, we got a crash on the system.
Signed-off-by: Guilherme G Piccoli <gpiccoli@linux.vnet.ibm.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
in commit a036244c06 a fix
was put into place to avoid a kernel panic when a non-
supported traffic class configuration was put into place
and then lldp was enabled/disabled on the link partner
switch. This fix caused it to be necessary to
unload/reload the driver to reenable DCB once a supported
TC config was in place.
The root cause of the original panic was that the function
i40e_pf_get_default_tc was allowing for a default TC other
than TC 0, and only TC 0 is supported as a default.
This patch removes the get_default_tc function and replaces
it with a #define since there is only one TC supported as
a default.
Change-Id: I448371974e946386d0a7718d73668b450b7c72ef
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Ronald Bynoe <ronald.j.bynoe@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Fix NULL pointer dereference in the case where a macvlan interface is
brought up while the PF is still down:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
IP: [<ffffffffa0170fb2>] ixgbe_alloc_rx_buffers+0x42/0x1a0 [ixgbe]
Call Trace:
[<ffffffffa017336b>] ixgbe_configure_rx_ring+0x2eb/0x3d0 [ixgbe]
[<ffffffffa0173811>] ixgbe_fwd_ring_up+0xd1/0x380 [ixgbe]
[<ffffffffa0179709>] ixgbe_fwd_add+0x149/0x230 [ixgbe]
[<ffffffffa0113480>] macvlan_open+0x260/0x2b0 [macvlan]
Reported-by: Matthew Garrett <mjg59@coreos.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
trivial fix to spelling mistake in dev_err message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return error code -EINVAL from the error handling
case instead of 0, as done elsewhere in this function.
Fixes: e420114eef ("rocker: introduce worlds infrastructure")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 3ac72b7b63 ("net: fec: align IP header in hardware") breaks
networking on mx28.
There is an erratum on mx28 (ENGR121613 - ENET big endian mode
not compatible with ARM little endian) that requires an additional
byte-swap operation to workaround this problem.
So call swap_buffer() prior to performing the IP header alignment
to restore network functionality on mx28.
Fixes: 3ac72b7b63 ("net: fec: align IP header in hardware")
Reported-and-tested-by: Henri Roosen <henri.roosen@ginzinger.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Time Sync (PTP) implementation uses the divisor/shift value for converting
the clock ticks to nanoseconds. Driver currently defines shift value as 1,
this results in the nanoseconds value to be calculated as half the actual
value. Hence the user application fails to synchronize the device clock
value with the PTP master device clock. Need to use the 'shift' value of 0.
Signed-off-by: Sony.Chacko <Sony.Chacko@cavium.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver uses incorrect APIs to unmap DMA memory which were
mapped using dma_map_single(). This patch fixes it to use
appropriate APIs for un-mapping DMA memory.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
