When we enter D0i3, we must stop TXing otherwise the
sequence number we use might conflict with the firmware's
internal TX. In order to do so, we have
IWL_MVM_STATUS_IN_D0I3 which should prevent any Tx while we
enter D0i3. There is a bug in this code since we may Tx even
if IWL_MVM_STATUS_IN_D0I3 is set. This can happen as long as
mvm->d0i3_ap_sta_id is not set.
To make sure that we don't have any packet in the Tx path
while we set mvm->d0i3_ap_sta_id, call synchronize_net only
after we already set mvm->d0i3_ap_sta_id.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently if we wake up during D0I3 due to beacon loss we disconnect
immediately. This behaviour causes redundant disconnection, which could
be prevented by polling as it is usually done in mac80211.
Instead, we prefer reporting beacon loss and let mac80211 try polling
before disconnection.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
KASan error report:
==================================================================
BUG: KASan: out of bounds access in iwl_init_sband_channels+0x207/0x260 [iwlwifi] at addr ffff8800c2d0aac8
Read of size 4 by task modprobe/329
==================================================================
Both loops of this function compare data from the 'chan' array and then
check if the index is valid.
The 2 conditions should be inverted to avoid an out-of-bounds access.
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fix bug where MIMO is disabled for low latency TX on P2P VIF
regardless of configuration. Make it dependent on
IWL_MVM_RS_DISABLE_P2P_MIMO compilation option. Change configuration
so that MIMO will be disabled only in SDIO platforms.
Signed-off-by: Alexander Bondar <alexander.bondar@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
MAC/BB name is"????" if the MAC/BB is unknown.
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add diversity statistics and sync the driver
statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Sync the driver statistics acx and debugfs representation
with the current fw api.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rt2500usb_validate_eeprom() read data up to 0x6e (EEPROM_CALIBRATE_OFFSET)
but only 0x6a bytes has been allocated and read from the eeprom.
This lead to out-of-bound accesses and invalid values for
EEPROM_BBPTUNE_R17 and EEPROM_CALIBRATE_OFFSET.
Change the EEPROM_SIZE to 0x6e in order to retrieve all the fields.
Tested with a rt2570 device.
Signed-off-by: Adrien Schildknecht <adrien+dev@schischi.me>
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CC [M] drivers/net/wireless/mwl8k.o
drivers/net/wireless/mwl8k.c: In function ‘mwl8k_bss_info_changed’:
drivers/net/wireless/mwl8k.c:3290:2: warning: ‘ap_mcs_rates’ may be used uninitialized in this function [-Wmaybe-uninitialized]
memcpy(cmd->mcs_set, mcs_rates, 16);
^
drivers/net/wireless/mwl8k.c:4987:5: note: ‘ap_mcs_rates’ was declared here
u8 ap_mcs_rates[16];
^
The warning was bogus. But the conditionals were rather complicated,
with multiple redundant checks. This consolidates the checking and
makes it more readable IMHO.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
I remove duplicated routines which related rtl92cu_set_hw_reg().
1. rtl92c_set_qos() and HW_VAR_AC_PARAM routine are similar code.
so i replace code with rtlpriv->cfg->ops->set_hw_reg().
2. rtl92c_set_mac_addr() and 'HW_VAR_ETHER_ADDR' case at
rtl92cu_set_hw_reg() routine are similar code.
so i removed rtl92c_set_mac_addr() function.
also it was not used anywhere.
3. remove HW_VAR_ACM_CTRL routine in rtl92cu_set_hw_reg().
if rtl_usb->acm_method is not EACMWAY2_SW, HW_VAR_ACM_CTRL is called
from HW_VAR_AC_PARAM. but it never called. because acm_method is always
EACMWAY2_SW. so i remove acm_method check routine
and HW_VAR_ACM_CTRL routine.
both usb and pci interface is not used HW_VAR_ACM_CTRL.
but i can't test pci interface module, so i didn't modify pci code.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
rtl92c_set_xxx_filter is same routine with rtl92cu_set_hw_reg.
so i remove those functions that are rtl92c_set_xxx_filter.
(rtl92c_get_xxx_filter is also same reason.)
also i add code updating struct rtl_mac member variable in the
rtl92cu_set_hw_reg.
after that, no more _update_mac_setting is not useful. thus i remove that.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' mac80211-next.git
iwlwifi needs new mac80211 patches so merge mac80211-next.git to
wireless-drivers-next.git.
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' of git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another pull request for the next cycle, this time with quite
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
WMI 10.4 uses the same command interface as QCA988X for addba/delba
debug wmi commands. Fill wmi_10_4_ops table with the functions used
for QCA988X for these commands.
With this change, the following debugfs entries can be used to
configure the aggregation mode and to send addba request,
addba response and delba respectively in manual aggregation mode
for QCA99X0 chip.
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/aggr_mode
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/addba_resp
/sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Header format of 10.4 firmware phyerr event is not alligned
with pre 10.4 firmware. Introduce new wmi handlers to parse
10.4 firmware specific phyerror event header.
With changes covered in this patch, radar detection works on
qca9x0 hw 2.0 which uses 10.4 firmware.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Existing phyerr event handlers directly uses phyerr header format
(ie, struct wmi_phyerr and struct wmi_phyerr_event) in the code
exactly on how firmware packs it. This is the problem in 10.4 fw
specific phyerr event handling where it uses different phyerror
header format. Before adding 10.4 specific handler, little bit of
refactor is done in existing phyerr handlers.
Two new abstracted structures (struct wmi_phyerr_ev_hdr_arg and
struct wmi_phyerr_ev_arg) are introduced to remove dependency of using
firmware specific header format in the code. So that firmware specific
phyerror handlers can populate values to abstracted structures and
the following code can use abstracted struct for further operation.
.pull_phyerr_hdr is added newly to pull common phyerr header info
like tsf, buf_len, number of phyerr packed. Existing .pull_phyerr
handler is changed and called to parse every sub phyerrs in the event.
Validated these refactoring on qca988x hw2.0 using fw 10.2.4 version.
Signed-off-by: Raja Mani <rmani@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Return type of wait_for_completion_timeout is unsigned long not int.
As remain is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/wil6210/wmi.c:827
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_WIL6210=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Apparently it's not safe to install both pairwise
and groupwise keys on AP vdevs as it can cause
traffic to stop working in some multi-vif
(WPA+WEP) cases.
Fixes: ce90b27128 ("ath10k: fix multiple key static wep with ibss")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
The frequency at which cycle/rx_clear counters are running might
change from one target type to another. QCA99X0 is running the
counters at 150Mhz while QCA9888X and QCA6174 are running at 88Mhz.
Add a new entry to hw_params to store the target specific frequency
and use it in msecs conversion. This change fixes inconsistent
channel active/busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
There are three WMI_CHAN_INFO events reported per channel
in QCA99X0 firmware. First one is a notification at the begining
of the channel dwell time with cmd_flag as CHAN_INFO_START(cmd_flag = 0),
second one is a notification at the end of the dwell time with cmd_flag
CHAN_INFO_PRE_COMPLETE (cmd_flag = 2) and the third is the indication
with CHAN_INFO_COMPLETE (cmd_flag = 1) which is the last indication for
the channel. Since there is a new state before the completion, the handler
is to fixed so that the counts are deducted from the ones reported with
CHAN_INFO_START rather than the ones reported with CHAN_INFO_PRE_COMPLETE.
Without this fix there will be lots of 0 msecs reported as active
and busy time.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Vif's vdev_id is used as queue number. However due
to the tx pausing design in ath10k it was possible
for a new interface to be created with its tx
queue stopped (via ieee80211_stop_queues). This
could in turn leave the interface inoperable until
ath10k_mac_tx_unlock() was called.
This problem only affected multi-vif scenarios when
new interfaces were created some time later after
other interfaces have been running for some time
and had Tx queue full at some point prior.
Possible manifestation of the bug was
authentication timeout for a client vif.
Fixes: 96d828d45e ("ath10k: rework tx queue locking")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Once HTT Tx queue got full offchannel queue was
stopped and never woken up again. This broke, e.g.
P2P. This could be reproduced after running a lot
of traffic enough to saturate 100% of the driver
Tx queue and then trying to send offchannel
traffic.
Fixes: 96d828d45e ("ath10k: rework tx queue locking")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
* add support for qca99x0 family of devices
* improve performance of tx_lock
* add support for raw mode (802.11 frame format) and software crypto
engine enabled via a module parameter
wil6210:
* implement TSO support
* support bootloader v1 and onwards
Currently the driver disable power management on all low-latency
interfaces, while it should disable it on WiDi interfaces only.
Non-P2P interfaces that runs voice and video traffic should enable
power management.
Signed-off-by: Avri Altman <avri.altman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When TDLS support is declared by the FW, set the bit indicating wider-BW
support as well.
Signed-off-by: Arik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The &mvm->tof_data.range_req.ap[] array has IWL_MVM_TOF_MAX_APS elements
so the check should be >= instead of >. Also the test can underflow so
I have changed "i" to unsigned.
Fixes: ce7929186a ('wlwifi: mvm: add basic Time of Flight (802.11mc FTM) support')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
There is no need to use hex_dump_to_buffer() in the cases like this:
hexdump_to_buffer(buf, len, 16, 1, outbuf, outlen, false); /* len <= 16 */
sprintf("%s\n", outbuf);
since it maybe easily converted to simple:
sprintf("%*ph\n", len, buf);
Note: it seems in one case the output is groupped by 2 bytes and looks like a
typo. Thus, patch changes that to plain byte stream.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The mac80211 patch to pass the NAPI struct only changed iwlwifi to
store the NAPI struct, but we can do better: pass it directly from
the lower transport layer to the opmode during RX, and then on to
mac80211 from there.
When we add multiple RX queues, we can then pass the appropriate
NAPI struct properly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
-----BEGIN PGP SIGNATURE-----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=kV1a
-----END PGP SIGNATURE-----
Merge tag 'mac80211-next-for-davem-2015-08-14' into next
Another pull request for the next cycle, this time with quite
a bit of content:
* mesh fixes/improvements from Alexis, Bob, Chun-Yeow and Jesse
* TDLS higher bandwidth support (Arik)
* OCB fixes from Bertold Van den Bergh
* suspend/resume fixes from Eliad
* dynamic SMPS support for minstrel-HT (Krishna Chaitanya)
* VHT bitrate mask support (Lorenzo Bianconi)
* better regulatory support for 5/10 MHz channels (Matthias May)
* basic support for MU-MIMO to avoid the multi-vif issue (Sara Sharon)
along with a number of other cleanups.
Lmac sched scan supports partial scans, so we can set some channels to be
scanned on every scan iteration and others to be scanned only on some
iterations. Currently we set all channels to be scanned every iteration,
but still have some configuration of which iterations should be partial
and which should be full.
Remove all partial/full scan configuration to reduce confusions.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Remove timing values from iwl_mvm_scan_params and use defines and
arrays of values instead.
While at that fix few values and corner cases and align all OSs
to ChromeOS values.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Reviewed-by: Luciano Coelho <luciano.coelho@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We added calls to d3_suspend/resume trans ops during the
suspend/resume flow.
However, the wrapper code didn't verify the trans ops were
actually defined, resulting in panic when they were not
(such as in the case of sdio trans)
Fixes: 6dfb36c89d ("iwlwifi: call d3_suspend/resume in d0i3 case as well")
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
During hwsim_init_netlink(), we should call genl_unregister_family()
if failed on netlink_register_notifier() since the genetlink is
already registered.
Signed-off-by: Su Kang Yin <cantona@cantona.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_orinocodev() would allocate the wiphy entry, but it would only get
registered much later in orinoco_init(). If something failed in the init
process inbetween the call to alloc_orinocodev() and the completion
of orinoco_init(), the drivers would end up calling wiphy_unregister()
with a NULL pointer causing beautiful OOPS fireworks.
Explicitly call wiphy_unregister() instead in the right places.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Our 8887 A2 chip can have separate firmware images for
bluetooth and WLAN. We observed an issue during parallel
downloading of these images by btmrvl and mwifiex drivers.
This patch claims sdio bus before starting of the firmware
download in mwifiex and releases it after completion to
fix the problem.
Signed-off-by: Aniket Nagarnaik <aniketn@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We will check if any hidden SSID found in passive scan channels
and do specific SSID active scan for those channels.
Signed-off-by: chunfan chen <jeffc@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds firmware dump feature for SD8997 chipset.
The difference here is only one memory type is needed
to save all firmware information. Device dump information
will be uploaded to usersapace file.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds support for 8997 chipset to mwifiex
with SDIO/PCIe/USB interface.
The corresponding firmware image files are located in:
"mrvl/sd8997_uapsta.bin"
"mrvl/pcie8997_uapsta.bin"
"mrvl/usb8997_uapsta.bin"
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current code returns success if kmalloc fails.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In this driver, two variables are masked by one quantity, and then tested
against a second number with more bits that the mask. Accordingly, the
test always fails. To minimize the possibility of such typos, a symbolic
definition of the mask is created and used.
The separate load and mask operations are also combined into a single
statement.
Reported-by: David Binderman <dcb314@hotmail.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: David Binderman <dcb314@hotmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This driver is converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The drivers are converted to use the common firmware header struct.
Because the old header definition failed to indicate that the multi-byte
entries should be little endian, several problems were thus exposed.
These are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit e996db6983 (rtlwifi: rtl8192c: Add init codes for "fw_version"
and "fw_subversion") added initialization for fw_version, but failed to
note that the variable in the firmware header is little-endian. The
following Sparse warning results:
CHECK drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: warning: incorrect type in assignment (different base types)
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: expected unsigned short [unsigned] [usertype] fw_version
drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c:242:36: got restricted __le16 [usertype] version
When fixing this problem, I noticed that several of the drivers contain
nearly identical copies of the firmware header struct, and that only the one
used in rtl8192c{e,u} had correct endian notation. The struct has been
moved into a common header, and the other drivers will be fixed in
subsequant patches.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/link.c:197
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/wmi.c:331
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_drv_init.c:81
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Return type of wait_for_completion_timeout is unsigned long not int.
As time_left is exclusively used for wait_for_completion_timeout here its
type is simply changed to unsigned long.
API conformance testing for completions with coccinelle spatches are being
used to locate API usage inconsistencies:
./drivers/net/wireless/ath/ath9k/htc_hst.c:171
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:277
int return assigned to unsigned long
./drivers/net/wireless/ath/ath9k/htc_hst.c:206
int return assigned to unsigned long
Patch was compile tested with x86_64_defconfig + CONFIG_ATH_CARDS=m,
CONFIG_ATH9K_HTC=m
Patch is against 4.1-rc3 (localversion-next is -next-20150514)
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware peer entries are involved in internal
firmware vdev structures. This was not accounted
for and could lead firmware to crash due to asking
it to do more than it could.
Fixes: 039a0051ec ("ath10k: allocate fw resources for iface combinations")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If peer creation failed during offchannel Tx the
driver attempted to delete the peer nonetheless.
This caused the ar->num_peers counter to be
incorrectly decremented. This subsequently could
cause the counter to drop below 0 and also
eventually lead to firmware crash because host
would think there are less peer entries created in
firmware then there really were.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When WoWLAN resume fails with retval 1 mac80211
will attempt to reconfig the device in a similar
manner when hw restart is requested. This wasn't
handled properly and yielded call trace warnings
and the device ended up not working.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
If firmware did not have any feature flags set the
var would be left with values found on the stack
(i.e. garbage) yielding print string like this:
(...) features \xffffffa6m:^R\xfffffffbԂ\xffffffc4^E
Fixes: b27bc5a40f ("ath10k: dump fw features during probing")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This patch enables MU-MIMO transmit beamforming support
for QCA99X0 chipsets.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
qca61x4 uses the vdev param as a sole sufficient configuration
for txbf while qca99x0 enables txbf during peer assoc by
combining the vdev param value with peer assoc's vht capabilities
This patch gets the appropriate txbf configuration scheme
before passing the wmi command to enable the same in the firmware.
Signed-off-by: Vivek Natarajan <nataraja@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Even though there's a WMI enum for fragmentation
threshold no known firmware actually implements
it. Moreover it is not possible to rely frame
fragmentation to mac80211 because firmware clears
the "more fragments" bit in frame control making
it impossible for remote devices to reassemble
frames.
Hence implement a dummy callback just to say
fragmentation isn't supported. This effectively
prevents mac80211 from doing frame fragmentation
in software.
This fixes Tx becoming broken after setting
fragmentation threshold.
Fixes: 1010ba4c5d ("ath10k: unregister and remove frag_threshold callback")
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Commit 1010ba4c5d ("ath10k: unregister and
remove frag_threshold callback") didn't remove all
instances of (futile) fragmentation threshold
configuration. No known firmware supports the
parameter so don't even bother setting it.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
According to firmware engineers, the firmware has never required
these fields and the values have always been calculated, they were
just leftovers from a previous implementation.
Therefore remove the unnecessary calculation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Make ath_opmode_to_string return "OCB" for NL80211_IFTYPE_OCB. Currently
it will return "UNKNOWN".
Signed-off-by: Bertold Van den Bergh <bertold.vandenbergh@esat.kuleuven.be>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Add a spinlock which will ensure that.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mac80211 requires that rx path does not run concurrently with
tx status reporting. Since rx path is run in driver tasklet,
tx status cannot be reported directly from interrupt context
(there would be no way to lock it out).
Add tasklet for tx and move all possible code from irq handler
there.
Note: tx tasklet is needed because workqueue is queued very
rarely and that kills TCP performance.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rx is run inside a tasklet so ieee80211_rx() should be used
instead of ieee80211_rx_ni().
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
DMA to variables located on the stack is a bad idea.
For simplicity and to avoid frequent allocations create
a buffer inside the device structure. Protect this
buffer with vendor_req_mutex. Don't protect vendor
requests which don't use this buffer.
Signed-off-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When starting a p2p mgmt interface, enable its device role. This
allows us to keep the sta role disabled and scan on the dev role.
In general, p2p management interfaces cannot send vif-specific commands
to FW, as the vif role id is invalid. Only off-channel data and scans
happen on this vif, so most ops are not relevant.
If the vif is a p2p mgmt vif, block some mac80211 ops.
Configure rate policies for p2p mgmt interface, as
otherwise p2p packets come out with arbitrary rates.
Since wpa_supplicant currently doesn't support standalone
p2p device mode (without another attached managed interface),
add p2p device to the allowed interface combinations without
decreasing the allowed station count.
Moreover, increase the station count in some cases, as AP
mode usually starts as station interface, and the AP interface
is now different from the p2p management one).
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add definitions and function prototypes for generic_cfg
command.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support for long intervals on sched scan.
If configured, the original request interval will
be used num_short_interval times, and then the
long interval will be used.
While on it, fix the scan command field names
to reflect the expected value is in ms (rather
than secs).
These values will be taken from the conf file,
so bump its version accordingly.
Signed-off-by: Eyal Shapira <eyal@wizery.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added support for a new time sync event
the event data contains the WiLink TSF value.
To trigger the event, a HW modification is required,
so as a supporting firmware binary.
Signed-off-by: Yaniv Machani <yanivma@ti.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit d8d2f19feb ("mwifiex: silence TDLS link delete failure
for nonexistent link") lowers the priority of error message when
TDLS link is already deleted. But it had got increased by
commit acebe8c10a ("mwifiex: change dbg print func to
mwifiex_dbg")
Reported-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Looks like the word "contiguous" is often mistyped.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Even though 'compatability' has a dedicated entry in the Wiktionary,
it's listed as 'Mispelling of compatibility'. Fix it.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch> for the atomic_helper.c
Signed-off-by: Jiri Kosina <jkosina@suse.com>
kbuild bot reported that commit 592fa228f2 ("ath9k: remove struct
ath_atx_ac") broke the build when CONFIG_ATH9K_STATION_STATISTICS is y.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 592fa228f2 ("ath9k: remove struct ath_atx_ac")
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=9MX3
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2015-08-04' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Deprecate -10.ucode
* Clean ups towards multiple Rx queues
* Add support for longer CMD IDs. This will be required by new
firmwares since we are getting close to the u8 limit.
* bugfixes for the D0i3 power state
* Add basic support for FTM
* More random that doesn't really stand out
For PCIe/USB chipsets, preallocated skb buffers are reused for
event handling. mwifiex_check_uap_capabilties() performs
skb_pull(). This patch adds missing skb_push() to restore skb's
data pointer/length.
This bug was introduced by commit debfc60081 ("mwifiex: update
AP WMM settings from BSS_START event")
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
add option to dynamically configure the fw
which debug traces to open
Signed-off-by: Guy Mishol <guym@ti.com>
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Preallocated event SKBs are getting reused for PCIe chipset.
Their physical addresses are shared with firmware so that
firmware can write data into them.
This patch makes sure that SKB is cleared and length is set to
default while submitting it to firmware.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
System crash was observed if one of the driver initialisation
commands is timed out. The reason is our timeout handler triggers
firmware dump, meanwhile driver initialisation error paths have
already freed the adapter structure.
Firmware hasn't yet completely initialized. So collecting firmware
dump is not needed in this case. Command timeout handler is
modified in this patch to fix the crash issue.
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When WLAN interface is up and running, driver unload and
load was causing command timeout error.
We enable Rx data by updating RX ring read pointer in
init_fw_port(). It should be done when FW is completely
intialialised. Command timeout is fixed in this patch by
moving init_fw_port() call to mwifiex_init_fw_complete().
Signed-off-by: Zhaoyang Liu <liuzy@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Variable pos is u8 here, so memcpy is needed to store u16 aid.
At the same time, aid should be platform independent, upper layer
utility(wpa_supplicant,etc.,) parse it as le16, so keep it le16
here.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
struct ath_atx_ac contains a list of active TIDs belonging to one WMM AC.
This patch changes the code to track active station TIDs in the txq directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Setup rxfiler correctly for offchannel ctx.
This fix problem we didn't configure rxfilter, next
didn't receive probe requests and next failed
p2p_find. This was seen when ath9k loaded with
use_chanctx=1
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
While mac80211 setup this per HW, set same
rxfilter configuration for all chanctx.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Advertise p2p device support when ath9k loaded with
use_chanctx=1.
This will fix problem, when first interface is an AP
and next we would like to run p2p_find.
Before p2p find (scan phase) failed with EOPNOTSUPP.
Signed-off-by: Janusz Dziedzic <janusz.dziedzic@tieto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
600f5d909a54("mwifiex: cleanup ioctl wait queue and abstraction layer")
introduced the wakeup_interruptible suppression in mwifiex_complete_cmd
b1a47aa5e1e1("mwifiex: fix system hang issue in cmd timeout error case")
then added wakup_interruptible to mwifiex_cmd_timeout_func the single
place setting a status of ETIMEDOUT.
Instead of doing extra work, using the standard call-chain will have the
same effect:
mwifiex_cancel_pending_ioctl
-> mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd
-> wake_up_interruptible
The difference is that previously the condition was not set to true,
but that's probably just an oversight in b1a47aa5e1 and shouldn't
have any consequence
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CMD_F_CANCELED was used to abort mwifiex_process_cmdresp in
case it already started or starts processing the cmd.
But this was probably not working the way intended:
- it is racy: mwifiex_process_cmdresp might already have passed that
test and is continuing to use the cmd node being recycled
- mwifiex_process_cmdresp repeatedly uses adapter->curr_cmd which
we just set to NULL
- mwifiex_recycle_cmd_node will clear the flag
The reason why it probably works is that mwifiex_cancel_pending_ioctl
is only called from mwifiex_cmd_timeout_func, where the there is little
chance of a command response still arriving
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
mwifiex_cancel_pending_ioctl is called only from
mwifiex_cmd_timeout_func. There the wait_q status is set to
-ETIMEDWAIT before calling this function. Whether we reset the status
to -1 or leave it at -ETIMEDWAIT at end doesn't matter since both
are != 0 hence mean failure
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
standard call chain when releasing a cmd node:
mwifiex_recycle_cmd_node
-> mwifiex_insert_cmd_to_free_q
-> mwifiex_complete_cmd, if wait_q_enabled
calling mwifiex_complete_cmd explicitly and setting
wait_q_enabled = false is redundant
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since 1fb654fd97ff("mmc: sdio: add reset callback to bus operations"),
sdio cards can be power cycled using mmc_hw_reset.
The use mmc_remove_host/mmc_add_host is discouraged, because these are
internal functions to the mmc core and should only be used by mmc hosts
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Acked-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Boot loader versions as backward compatible,
starting from v1
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Boot loader reports error starting from the struct v2.
Print error info before reset (power up state) in debug mode,
and print same info as error if target reset timed out.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Support for the system suspend/resume.
In preparation for the run-time PM, implementation made
run-time PM friendly: common for system and run-time PM
code factored out as generic functions, albeit is_runtime
parameter value is always false currently.
For debug purposes, "PM" debug category introduced.
Policy: AP-like interface can't be suspended; otherwise
suspend is allowed. Hardware brought down if interface
was up. Connection, if existed, get lost.
Interface will be brought up upon resume if it was up
before suspend.
Signed-off-by: Vladimir Kondratiev <qca_vkondrat@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
