We should not use physid_mask_t as a stack based
variable in apic code. This type depends on MAX_APICS
parameter which may be huge enough.
Especially it became a problem with apic NOOP driver which
is portable between 32 bit and 64 bit environment
(where we have really huge MAX_APICS).
So apic driver should operate with pointers and a caller
in turn should aware of allocation physid_mask_t variable.
As a side (but positive) effect -- we may use already
implemented physid_set_mask_of_physid function eliminating
default_apicid_to_cpu_present completely.
Note that physids_coerce and physids_promote turned into static
inline from macro (since macro hides the fact that parameter is
being interpreted as unsigned long, make it explicit).
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
LKML-Reference: <20091109220659.GA5568@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In fact it's never get used on x86-64 (for 64 bit platform
we use differ technique to enumerate io-units).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20091108131645.GD5300@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should be ready that one day MAX_IO_APICS may raise its
number. To prevent memory overwrite we're to use safe
snprintf while set IO-APIC resourse name.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20091108155431.GC25940@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The whole page is reserved for IO-APIC fixmap
due to non-cacheable requirement. So lets note
this explicitly instead of playing with numbers.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
LKML-Reference: <20091108155356.GB25940@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To ensure that we handle all the pending interrupts (destined
for this cpu that is going down) in the interrupt subsystem
before the cpu goes offline, fixup_irqs() does:
local_irq_enable();
mdelay(1);
local_irq_disable();
Enabling interrupts is not a good thing as this cpu is already
offline. So this patch replaces that logic with,
mdelay(1);
check APIC_IRR bits
Retrigger the irq at the new destination if any interrupt has arrived
via IPI.
For IO-APIC level triggered interrupts, this retrigger IPI will
appear as an edge interrupt. ack_apic_level() will detect this
condition and IO-APIC RTE's remoteIRR is cleared using directed
EOI(using IO-APIC EOI register) on Intel platforms and for
others it uses the existing mask+edge logic followed by
unmask+level.
We can also remove mdelay() and then send spuriuous interrupts
to new cpu targets for all the irqs that were handled previously
by this cpu that is going offline. While it works, I have seen
spurious interrupt messages (nothing wrong but still annoying
messages during cpu offline, which can be seen during
suspend/resume etc)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230002.043281924@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
IO-APIC's in intel chipsets support EOI register starting from
IO-APIC version 2. Use that when ever we need to clear the
IO-APIC RTE's RemoteIRR bit explicitly.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.947855317@sbs-t61.sc.intel.com>
[ Marked use_eio_reg as __read_mostly, fixed small details ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When a cpu goes offline, fixup_irqs() try to move irq's
currently destined to the offline cpu to a new cpu. But this
attempt will fail if the irq is recently moved to this cpu and
the irq still hasn't arrived at this cpu (for non intr-remapping
platforms this is when we free the vector allocation at the
previous destination) that is about to go offline.
This will endup with the interrupt subsystem still pointing the
irq to the offline cpu, causing that irq to not work any more.
Fix this by forcing the irq to complete its move (its been a
long time we moved the irq to this cpu which we are offlining
now) and then move this irq to a new cpu before this cpu goes
offline.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.848830905@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
move_cleanup_count for each irq in irq_cfg is keeping track of
the total number of cpus that need to free the corresponding
vectors associated with the irq which has now been migrated to
new destination. As long as this move_cleanup_count is non-zero
(i.e., as long as we have n't freed the vector allocations on
the old destinations) we were preventing the irq's further
migration.
This cleanup count is unnecessary and it is enough to not allow
the irq migration till we send the cleanup vector to the
previous irq destination, for which we already have irq_cfg's
move_in_progress. All we need to make sure is that we free the
vector at the old desintation but we don't need to wait till
that gets freed.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.752968906@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the presence of interrupt-remapping, irqs will be migrated in
the process context and we don't do (and there is no need to)
irq_chip mask/unmask while migrating the interrupt.
Similarly fix the fixup_irqs() that get called during cpu
offline and avoid calling irq_chip mask/unmask for irqs that are
ok to be migrated in the process context.
While we didn't observe any race condition with the existing
code, this change takes complete advantage of
interrupt-remapping in the newer generation platforms and avoids
any potential HW lockup's (that often worry Eric :)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: garyhade@us.ibm.com
LKML-Reference: <20091026230001.661423939@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There is no reason to have different fixup_irqs() for 32-bit and
64-bit kernels. Unify by using the superior 64-bit version for
both the kernels.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Gary Hade <garyhade@us.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
LKML-Reference: <20091026230001.562512739@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit a98f8fd24f (x86: apic reset
counter on shutdown) set the counter to max to avoid spurious
interrupts when the timer is re-enabled.
(In theory) you'll still get a spurious interrupt if spending
more than 344 seconds with this interrupt disabled and then
unmasking it.
The right thing to do is to clear the register. This disables
the interrupt from happening (at least it does on AMD hardware).
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20091027100138.GB30802@alberich.amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As only apic noop is used we allow to use almost any operation
caller wants (and which of them noop driver supports of
course).
Initially it was reported by Ingo Molnar that apic noop
issue a warning for pkg id (which is actually false positive
and should be eliminated).
So we save checking (and warning issue) for read/write
operations while allow any other ops to be freely used.
Also:
- fix noop_cpu_to_logical_apicid, it should be 0.
- rename noop_default_phys_pkg_id to noop_phys_pkg_id
(we use default_ prefix for more general routines
in apic subsystem).
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
LKML-Reference: <20091015150416.GC5331@lenovo>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This warning:
In file included from arch/x86/include/asm/ipi.h:23,
from arch/x86/kernel/apic/apic_noop.c:27:
arch/x86/include/asm/hw_irq.h:105: warning: ‘struct irq_desc’ declared inside parameter list
arch/x86/include/asm/hw_irq.h:105: warning: its scope is only this definition or declaration, which is probably not what you want
triggers because irq_desc is defined after hw_irq.h is included
in irq.h. Since it's pointer reference only, a forward declaration
of the type will solve the problem.
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Move UV specific functionality out of the generic IO-APIC code.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
LKML-Reference: <20091013203236.GD20543@sgi.com>
[ Cleaned up the code some more in their new places. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes handling of uv hub irq affinity. IRQs with ALL or
NODE affinity can be routed to cpus other than their originally
assigned cpu. Those with CPU affinity cannot be rerouted.
Signed-off-by: Dimitri Sivanich <sivanich@sgi.com>
LKML-Reference: <20090930160259.GA7822@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case if a system has a large number of cpus printing apics
contents may consume a long time period.
We limit such an output by 1 apic by default. But to have an
ability to see all apics or some part of them we introduce
"show_lapic" setup option which allow us to limit/unlimit the
number of APICs being dumped.
Example: apic=debug show_lapic=5, or apic=debug show_lapic=all
Also move apic_verbosity checking upper that way so helper routines
do not need to inspect it at all.
Suggested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
Cc: macro@linux-mips.org
LKML-Reference: <20091013201022.926793122@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In case if apic were disabled we may use the whole apic NOOP driver
instead of sparse poking the some functions in apic driver.
Also NOOP would catch any inappropriate apic operation calls (not
just read/write).
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
Cc: macro@linux-mips.org
LKML-Reference: <20091013201022.747817361@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce NOOP APIC driver. We should use it in case if apic was
disabled due to hardware of software/firmware problems (including
user requested to disable it case).
The driver is attempting to catch any inappropriate apic operation
call with warning issue.
Also it is possible to use some apic operation like IPI calls,
read/write without checking for apic presence which should make
callers code easier.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: yinghai@kernel.org
Cc: macro@linux-mips.org
LKML-Reference: <20091013201022.534682104@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.infradead.org/~dwmw2/iommu-2.6.32:
x86: Move pci_iommu_init to rootfs_initcall()
Run pci_apply_final_quirks() sooner.
Mark pci_apply_final_quirks() __init rather than __devinit
Rename pci_init() to pci_apply_final_quirks(), move it to quirks.c
intel-iommu: Yet another BIOS workaround: Isoch DMAR unit with no TLB space
intel-iommu: Decode (and ignore) RHSA entries
intel-iommu: Make "Unknown DMAR structure" message more informative
On ARM, update_mmu_cache() does dcache flush for a page only if
it has a kernel mapping (page_mapping(page) != NULL). The correct
behavior would be to force the flush based on dcache_dirty bit only.
One of the cases where present logic would be a problem is when
a RAM based block device[1] is used as a swap disk. In this case,
we would have in-memory data corruption as shown in steps below:
do_swap_page()
{
- Allocate a new page (if not already in swap cache)
- Issue read from swap disk
- Block driver issues flush_dcache_page()
- flush_dcache_page() simply sets PG_dcache_dirty bit and does not
actually issue a flush since this page has no user space mapping yet.
- Now, if swap disk is almost full, this newly read page is removed
from swap cache and corrsponding swap slot is freed.
- Map this page anonymously in user space.
- update_mmu_cache()
- Since this page does not have kernel mapping (its not in page/swap
cache and is mapped anonymously), it does not issue dcache flush
even if dcache_dirty bit is set by flush_dcache_page() above.
<user now gets stale data since dcache was never flushed>
}
Same problem exists on mips too.
[1] example:
- brd (RAM based block device)
- ramzswap (RAM based compressed swap device)
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We want this to happen after the PCI quirks, which are now running at
the very end of the fs_initcalls.
This works around the BIOS problems which were originally addressed by
commit db8be50c43 ('USB: Work around BIOS
bugs by quiescing USB controllers earlier'), which was reverted in
commit d93a8f829f.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
PXA27x Errata #37 implies system will hang when switching into or out of
half turbo (HT bit in CLKCFG) mode, workaround this by not using it.
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Cc: stable-2.6.31 <stable@kernel.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Currently the irq_type field of the csb726_lan_config structure is
initialized twice. The value in the first case,
SMSC911X_IRQ_POLARITY_ACTIVE_LOW, is normally stored in the irq_polarity
field, so I have renamed the field in the first initialization to that.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
As reported in
http://bugzilla.kernel.org/show_bug.cgi?id=13940
on some system when acpi are enabled, acpi clears some BAR for some
devices without reason, and kernel will need to allocate devices for
them. It then apparently hits some undocumented resource conflict,
resulting in non-working devices.
Try to increase alignment to get more safe range for unassigned devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Seemingly this support was missed when highmem was added, so
DEBUG_HIGHMEM wouldn't have checked the kmap_atomic type.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Bit testing (test, testset, testclear, testchange) for bit numbers
known at compile time returns a word with the tested-for bit set.
Change it to return a true boolean value so to make it consistent with
the out-of-line path and all the other bitops implementations.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make die() better match x86:
- add printing of the last accessed sysfs file
- ensure console_verbose() is called under the lock
- ensure we panic outside of oops_exit()
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dump_mem and dump_backtrace were both using multiple printk statements
to print each line. With DEBUG_LL enabled, this causes OOPS to become
very difficult to read. Solve this by only using one printk per line.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The clock generation system in the ep93xx uses two external oscillator's
and two internal PLLs to derive all the internal clocks. Many of these
internal clocks can be stopped to save power.
This introduces a "parent" hierarchy for the clocks so that the users
count can be correctly tracked for power management.
The "parent" for the video clock can either be one of the PLL outputs
or the external oscillator. In order to correctly track the "parent"
for the video clock calc_clk_div() needed to be modified. It now
returns an error code if the desired rate cannot be generated.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the ep93xx i2c support:
1) The platform init code passes the configuration data for the
i2c-gpio driver. This allows any gpio pin do be used for the
sda and scl pins. It also allows the platform to specify the
udelay and timeout.
2) Program the gpio configuration register to enable/disable the
open drain drivers. Note that this really only works if the
sda and scl pins are set to EP93XX_GPIO_LINE_EEDAT and
EP93XX_GPIO_LINE_EECLK.
3) Update the edb93xx.c platform init to use the new support.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Most of the EP93XX_GPIO_*_INT_* register defines in ep93xx-regs.h
not required due to how the ep93xx core and gpiolib support handle
gpio interrupts. Remove the defines to prevent future confusion.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin:
Blackfin: convert to GENERIC_HARDIRQS_NO__DO_IRQ
Blackfin: drop all simple-gpio board resources
Blackfin: fix framebuffer mmap bug for nommu
Blackfin: includecheck fix: mach-bf548, ezkit.c
Blackfin: drop cs_change_per_word setting
Blackfin: bf533-ezkit: convert to physmap/jedec_probe
Blackfin: convert adv7393 resources to new i2c framework
Blackfin: fix missed cache config renames
Blackfin: cplbinfo: drop d_path() hacks
Blackfin: asm/irq.h: pull in mach/anomaly.h for anomaly defines
Blackfin: BF51x: add PTP MMR defines
Blackfin: mass clean up of copyright/licensing info
Blackfin: convert to use arch_gettimeoffset()
* 'sh/for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Don't allocate smaller sized mappings on every iteration
sh: Try PMB mapping based on physical address, not mapping size
sh: Plug PMB alloc memory leak
sh: Sprinkle __uses_jump_to_uncached
sh: enable sleep state LEDs on Ecovec24
usb: r8a66597-udc unaligned fifo fix
sh: mach-ecovec24: Document DS2 switch settings.
sh: Build fix: export __movmem
sh: Disable unaligned kernel access printks by default.
sh: mach-ecovec24: modify 1st MTD area to read only
sh: mach-ecovec24: Add TouchScreen support
sh: magicpanelr2 and dreamcast can use the generic I/O base.
sh: Don't enable interrupts in the page fault path
sh: Set the default I/O port base to P2SEG.
sh: Handle ioport_map() cases for >= P1SEG addresses.
Currently, we've got the less than ideal situation where if we need to
allocate a 256MB mapping we'll allocate four entries like so,
entry 1: 128MB
entry 2: 64MB
entry 3: 16MB
entry 4: 16MB
This is because as we execute the loop in pmb_remap() we will
progressively try mapping the remaining address space with smaller and
smaller sizes. This isn't good because the size we use on one iteration
may be the perfect size to use on the next iteration, for instance when
the initial size is divisible by one of the PMB mapping sizes.
With this patch, we now only need two entries in the PMB to map 256MB of
address space,
entry 1: 128MB
entry 2: 128MB
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We should favour PMB mappings when the physical address cannot be
reached with 29-bits.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
If we fail to allocate a PMB entry in pmb_remap() we must remember to
clear and free any PMB entries that we may have previously allocated,
e.g. if we were allocating a multiple entry mapping.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix some callers of jump_to_uncached() and back_to_cached() that were
not annotated with __uses_jump_to_uncached.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the ecovec24 board code to enable Power
Management LEDs showing the current sh7724 sleep state.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'sparc-perf-events-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
mm, perf_event: Make vmalloc_user() align base kernel virtual address to SHMLBA
perf_event: Provide vmalloc() based mmap() backing
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, timers: Check for pending timers after (device) interrupts
NOHZ: update idle state also when NOHZ is inactive
Now that range timers and deferred timers are common, I found a
problem with these using the "perf timechart" tool. Frans Pop also
reported high scheduler latencies via LatencyTop, when using
iwlagn.
It turns out that on x86, these two 'opportunistic' timers only get
checked when another "real" timer happens. These opportunistic
timers have the objective to save power by hitchhiking on other
wakeups, as to avoid CPU wakeups by themselves as much as possible.
The change in this patch runs this check not only at timer
interrupts, but at all (device) interrupts. The effect is that:
1) the deferred timers/range timers get delayed less
2) the range timers cause less wakeups by themselves because
the percentage of hitchhiking on existing wakeup events goes up.
I've verified the working of the patch using "perf timechart", the
original exposed bug is gone with this patch. Frans also reported
success - the latencies are now down in the expected ~10 msec
range.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Tested-by: Frans Pop <elendil@planet.nl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <20091008064041.67219b13@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
agp: parisc-agp.c - use correct page_mask function
parisc: Fix linker script breakage.
parisc: convert to asm-generic/hardirq.h
parisc: Make THREAD_SIZE available to assembly files and linker scripts.
parisc: correct use of SHF_ALLOC
parisc: rename parisc's vmalloc_start to parisc_vmalloc_start
parisc: add me to Maintainers
parisc: includecheck fix: signal.c
parisc: HAVE_ARCH_TRACEHOOK
parisc: add skeleton syscall.h
parisc: stop using task->ptrace for {single,block}step flags
parisc: split syscall_trace into two halves
parisc: add missing TI_TASK macro in syscall.S
parisc: tracehook_signal_handler
parisc: tracehook_report_syscall
Blackfin already sets proper flow handlers on all IRQs, and we don't rely
on __do_IRQ, therefore we can simply select GENERIC_HARDIRQS_NO__DO_IRQ.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
