arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
arch/arm/mach-realview/platsmp.c:140: error: 'jiffies' undeclared (first use in this function)
drivers/amba/bus.c:246: error: 'NO_IRQ' undeclared (first use in this function)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Otherwise the mv643xx_eth driver will assume 133 MHz which is incorrect.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since mci.h has been moved, use the new include path.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix IRQ_EINT_GROUP which has an extra _ in it and
an error in the IRQ offset.
Signed-off-by: Matt Hsu <matt_hsu@openmoko.org>
[ben-linux@fluff.org: rewrite description]
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
The dc21285 requests a number of IRQs that it doesn't really
care whether they get added. Change to use a macro that ensures
that at-least the user gets warned if they fail to add, which
also stops the warnings from __unused_result on request_irq().
dc21285.c:337: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
dc21285.c:339: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
dc21285.c:341: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
dc21285.c:343: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
dc21285.c:345: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
isa_init_irq() is defined in arch/arm/mach-footbridge/isa-irq.c
and used in arch/arm/mach-footbridge/common.c but there is no
definition in any header. Move the definition in common.c to
common.h to stop the sparse warning:
isa-irq.c:118:13: warning: symbol 'isa_init_irq' was not declared.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
arch/arm/kernel/isa.c should include <linux/io.h> to get the
definition of register_io_ports() at-least when compiling for
footbridge to fix the following sparse warning:
isa.c:68:1: warning: symbol 'register_isa_ports' was not declared.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds the SPU event based profiling funcitonality for the
IBM Cell processor. Previously, the CELL OProfile kernel code supported
PPU event, PPU cycle profiling and SPU cycle profiling. The addition of
SPU event profiling allows the users to identify where in their SPU code
various SPU evnets are occuring. This should help users further identify
issues with their code. Note, SPU profiling has some limitations due to HW
constraints. Only one event at a time can be used for profiling and SPU event
profiling must be time sliced across all of the SPUs in a node.
The patch adds a new arch specific file to the OProfile file system. The
file has bit 0 set to indicate that the kernel supports SPU event profiling.
The user tool must check this file/bit to make sure the kernel supports
SPU event profiling before trying to do SPU event profiling. The user tool
check is part of the user tool patch for SPU event profiling.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
This patch restructures and cleans up the code a bit to make it
easier to add new functionality later. The patch makes no
functional changes to the existing code.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Make VMAs per mm_struct as for MMU-mode linux. This solves two problems:
(1) In SYSV SHM where nattch for a segment does not reflect the number of
shmat's (and forks) done.
(2) In mmap() where the VMA's vm_mm is set to point to the parent mm by an
exec'ing process when VM_EXECUTABLE is specified, regardless of the fact
that a VMA might be shared and already have its vm_mm assigned to another
process or a dead process.
A new struct (vm_region) is introduced to track a mapped region and to remember
the circumstances under which it may be shared and the vm_list_struct structure
is discarded as it's no longer required.
This patch makes the following additional changes:
(1) Regions are now allocated with alloc_pages() rather than kmalloc() and
with no recourse to __GFP_COMP, so the pages are not composite. Instead,
each page has a reference on it held by the region. Anything else that is
interested in such a page will have to get a reference on it to retain it.
When the pages are released due to unmapping, each page is passed to
put_page() and will be freed when the page usage count reaches zero.
(2) Excess pages are trimmed after an allocation as the allocation must be
made as a power-of-2 quantity of pages.
(3) VMAs are added to the parent MM's R/B tree and mmap lists. As an MM may
end up with overlapping VMAs within the tree, the VMA struct address is
appended to the sort key.
(4) Non-anonymous VMAs are now added to the backing inode's prio list.
(5) Holes may be punched in anonymous VMAs with munmap(), releasing parts of
the backing region. The VMA and region structs will be split if
necessary.
(6) sys_shmdt() only releases one attachment to a SYSV IPC shared memory
segment instead of all the attachments at that addresss. Multiple
shmat()'s return the same address under NOMMU-mode instead of different
virtual addresses as under MMU-mode.
(7) Core dumping for ELF-FDPIC requires fewer exceptions for NOMMU-mode.
(8) /proc/maps is now the global list of mapped regions, and may list bits
that aren't actually mapped anywhere.
(9) /proc/meminfo gains a line (tagged "MmapCopy") that indicates the amount
of RAM currently allocated by mmap to hold mappable regions that can't be
mapped directly. These are copies of the backing device or file if not
anonymous.
These changes make NOMMU mode more similar to MMU mode. The downside is that
NOMMU mode requires some extra memory to track things over NOMMU without this
patch (VMAs are no longer shared, and there are now region structs).
Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Mike Frysinger <vapier.adi@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Rename ARM's struct vm_region so that I can introduce my own global version
for NOMMU. It's feasible that the ARM version may wish to use my global one
instead.
The NOMMU vm_region struct defines areas of the physical memory map that are
under mmap. This may include chunks of RAM or regions of memory mapped
devices, such as flash. It is also used to retain copies of file content so
that shareable private memory mappings of files can be made. As such, it may
be compatible with what is described in the banner comment for ARM's vm_region
struct.
Signed-off-by: David Howells <dhowells@redhat.com>
This patch enables dynamic ftrace. The PowerPC port was dependent on
other code not yet in mainline. Now that the code is, we can now
let PowerPC compile with dynamic ftrace.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The clear_fixmap() routine issues map_page() with flags set to 0.
Currently this causes a BUG_ON() inside the map_page(), as it assumes
that a PTE should be clear before mapping.
This patch makes the map_page() to trigger the BUG_ON() only if the
flags were set.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The patch replaces internal registers dump implementation with
ppc_save_regs(). From now on PPC64 and PPC32 are using the same
code for crash_setup_regs().
NOTE: The old regs dump implementation was capturing SP (r1) directly
as is, so you could see crash_kexec() function on top of the back-trace.
But ppc_save_regs() goes up one stack frame, so you'll not see it
anymore, at the top-level you'll see who actually triggered the crash
dump instead.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The Freescale PowerPC specific gianfar driver (gig-e) uses
cacheable_memzero for performance reasons we need to export
the symbol to allow the driver to be built as a module.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is a brown paper bag from one of my earlier patches that
breaks build on 40x and 8xx.
And yes, I've now added 40x and 8xx to my list of test configs :-)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
[Split from a larger patch - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
in/out_be64() work on u64s.
The first parameter to ppc_md.ioremap is a phys_addr_t.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Only pass the address of a u64 if that is what the function requires.
[Split out of a larger patch - sfr]
[update comment - sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
tce_entryp is a "u64 *" not an "unsigned long *".
[Split from a large patch -sfr]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
of_get_flat_dt_prop() returns a "void *", so we don't need to cast when
assigning its result to a pointer variable.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Update ps3vram driver to use the new ps3 three id modalias support.
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ps3vram driver, which exposes unused video RAM on the PS3 as a MTD
device suitable for storage or swap. Fast data transfer is achieved
using a local cache in system RAM and DMA transfers via the GPU.
Signed-off-by: Vivien Chappelier <vivien.chappelier@free.fr>
Signed-off-by: Jim Paris <jim@jtan.com>
Acked-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
iSeries dependent drivers fail to build, when CONFIG_VIOPATH is disabled.
Fix the problem by making those drivers select it.
Signed-off-by: Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Enable RELOCATABLE option if user selects CRASH_DUMP option. Without this
patch user has to first select RELOCATABLE option and then has to enable
CRASH_DUMP option.
Signed-off-by: M. Mohan Kumar <mohan@in.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
So change the flags member of struct spu from u64 to unsigned long.
This change will also prevent some warnings when we change u64 to unsigned
long long.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
These ioctls take a struct serial_rs485
(see linux/serial.h) as argument. They are already available
on x86. This patch adds them for the powerpc architecture.
Signed-off-by: Matthias Fuchs <mfuchs@ma-fu.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
X has been failing to start on my quad G5 powermac since commit
1fd0f52583 ("powerpc: Fix domain numbers
in /proc on 64-bit") went in. The reason is that the change allows X
to see the PCI-PCI bridge above the video card (previously it was
obscured by the fact that there were two "00" directories in
/proc/bus/pci), and the pciconfig_iobase system call on the bridge is
failing because of a hack that we have to return information about the
AGP bus when X asks about bus 0. This machine doesn't have an AGP bus
(it has PCI Express) and so the pciconfig_iobase call is returning -1,
which ultimately causes X to fail to start.
This fixes it by checking that we have an AGP bridge before
redirecting the pciconfig_iobase call to return information about the
AGP bus. With this, X starts successfully both on a quad G5 with
PCI Express and on an older dual G5 with AGP.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested
in Documentation/spinlocks.txt
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
declarer name DEFINE_SPINLOCK;
identifier xxx_lock;
@@
- spinlock_t xxx_lock = SPIN_LOCK_UNLOCKED;
+ DEFINE_SPINLOCK(xxx_lock);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
SPIN_LOCK_UNLOCKED is deprecated. The following makes the change suggested
in Documentation/spinlocks.txt
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
declarer name DEFINE_SPINLOCK;
identifier xxx_lock;
@@
- spinlock_t xxx_lock = SPIN_LOCK_UNLOCKED;
+ DEFINE_SPINLOCK(xxx_lock);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The current code for providing processor cache information in sysfs
has the following deficiencies:
- several complex functions that are hard to understand
- implicit recursion (cache_desc_release -> kobject_put -> cache_desc_release)
- explicit recursion (create_cache_index_info)
- use of two per-cpu arrays when one would suffice
- duplication of work on systems where CPUs share cache
Also, when I looked at implementing support for a shared_cpu_map
attribute, it was pretty much impossible to handle hotplug without
checking every single online CPU's cache_desc list and fixing things
up... not that this is a hot path, but it would have introduced
O(n^2)-ish behavior during boot. Addressing this involved rethinking
the core data structures used, which didn't lend itself to an
incremental approach.
This implementation maintains a "forest" (potentially more than one
tree) of cache objects which reflects the system's cache topology.
Cache objects are instantiated as needed as CPUs come online. A
per-cpu array is used mainly for sysfs-related bookkeeping; the
objects in the array just point to the appropriate points in the
forest.
This maintains compatibility with the existing code and includes some
enhancements:
- Implement the shared_cpu_map attribute, which is essential for
enabling userspace to discover the system's overall cache topology.
- Use cache-block-size properties if cache-line-size is not available.
I chose to place this implementation in a new file since it would have
roughly doubled the size of sysfs.c, which is already kind of messy.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The non-zero return from the prepare callback is returned by sys_kexec_load()
to userspace, indicating that kexec is not supported on the machine.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch makes the default install script (arch/powerpc/boot/install.sh)
copy the bootable image files into the install directory. Before this
patch only the vmlinux image file was copied.
This patch makes the default 'make install' command useful for embedded
development when $(INSTALL_PATH) is set in the environment.
As a side effect, this patch changes the calling convention of the
install.sh script. Instead of a single 5th parameter, the script is now
passed a list of all the target images stored in the $(image-y) Makefile
variable. This should be backwards compatible with existing install scripts
since it just adds additional arguments and does not change existing ones.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Both users of careful_allocation() immediately memset() the
result. So, just do it in one place.
Also give careful_allocation() a 'z' prefix to bring it in
line with kzmalloc() and friends.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since we memset() the result in both of the uses here,
just make careful_alloc() return a virtual address.
Also, add a separate variable to store the physial
address that comes back from the lmb_alloc() functions.
This makes it less likely that someone will screw it up
forgetting to convert before returning since the vaddr
is always in a void* and the paddr is always in an
unsigned long.
I admit this is arbitrary since one of its users needs
a paddr and one a vaddr, but it does remove a good
number of casts.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If we fail a bootmem allocation, the bootmem code itself
panics. No need to redo it here.
Also change the wording of the other panic. We don't
strictly have to allocate memory on the specified node.
It is just a hint and that node may not even *have* any
memory on it. In that case we can and do fall back to
other nodes.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The behavior in careful_allocation() really confused me
at first. Add a comment to hopefully make it easier
on the next doofus that looks at it.
Signed-off-by: Dave Hansen <dave@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This patch fixes some unbalanced OF node references in the
powermac code
Signed-off-by: Nicolas Palix <npalix@diku.dk>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
There's a problem on some embedded platforms when we re-assign
everything on PCI, such as 44x. The generic code tries to avoid
assigning devices to addresses overlapping the low legacy
addresses such as VGA hard decoded areas using constants that
are unfortunately no good for us, as they don't take into account
the address translation we do to access PCI busses.
Thus we end up allocating things like IO BARs to 0, which is
technically legal, but will shadow hard decoded ports for use
by things like VGA cards.
This works around it by attempting to reserve legacy regions
before we try to assign addresses.
NOTE: This may have nasty side effects in cases I haven't tested
yet:
- We try to use FW mappings (ie. powermac) and the FW has allocated
a conflicting address over those legacy regions. This will typically
happen. I would expect the new code to just fail with an informative
message without harm but I haven't had a chance to test that scenario
yet.
- A device with fixed BARs overlapping those legacy addresses such
as an IDE controller in legacy mode is in the system. I don't know
for sure yet what will happen there, I have to test :-)
Ideally, we should change PCIBIOS_MIN_IO/MIN_MEM accross the board
to take a bus pointer so they can provide appropriate per-bus translated
values to the generic code but that's a more invasive patch. I will
do that in the future, but in the meantime, this fixes the problem
locally
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Work around branch tracer warning.
sparc64: Fix unsigned long long warnings in drivers.
sparc64: Use unsigned long long for u64.
sparc: refactor code in fault_32.c
sparc64: refactor code in init_64.c
sparc64: refactor code in viohs.c
sparc: make proces_ver_nack a bit more readable
As reported by Sam Ravnborg, Gcc-3.4.5 does not handle:
if (get_user() || get_user())
with the new branch tracer enabled.
Just seperate it out into seperate statements for now
so people can get work done.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (98 commits)
PCI PM: Put PM callbacks in the order of execution
PCI PM: Run default PM callbacks for all devices using new framework
PCI PM: Register power state of devices during initialization
PCI PM: Call pci_fixup_device from legacy routines
PCI PM: Rearrange code in pci-driver.c
PCI PM: Avoid touching devices behind bridges in unknown state
PCI PM: Move pci_has_legacy_pm_support
PCI PM: Power-manage devices without drivers during suspend-resume
PCI PM: Add suspend counterpart of pci_reenable_device
PCI PM: Fix poweroff and restore callbacks
PCI: Use msleep instead of cpu_relax during ASPM link retraining
PCI: PCIe portdrv: Add kerneldoc comments to remining core funtions
PCI: PCIe portdrv: Rearrange code so that related things are together
PCI: PCIe portdrv: Fix suspend and resume of PCI Express port services
PCI: PCIe portdrv: Add kerneldoc comments to some core functions
x86/PCI: Do not use interrupt links for devices using MSI-X
net: sfc: Use pci_clear_master() to disable bus mastering
PCI: Add pci_clear_master() as opposite of pci_set_master()
PCI hotplug: remove redundant test in cpq hotplug
PCI: pciehp: cleanup register and field definitions
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (123 commits)
wimax/i2400m: add CREDITS and MAINTAINERS entries
wimax: export linux/wimax.h and linux/wimax/i2400m.h with headers_install
i2400m: Makefile and Kconfig
i2400m/SDIO: TX and RX path backends
i2400m/SDIO: firmware upload backend
i2400m/SDIO: probe/disconnect, dev init/shutdown and reset backends
i2400m/SDIO: header for the SDIO subdriver
i2400m/USB: TX and RX path backends
i2400m/USB: firmware upload backend
i2400m/USB: probe/disconnect, dev init/shutdown and reset backends
i2400m/USB: header for the USB bus driver
i2400m: debugfs controls
i2400m: various functions for device management
i2400m: RX and TX data/control paths
i2400m: firmware loading and bootrom initialization
i2400m: linkage to the networking stack
i2400m: Generic probe/disconnect, reset and message passing
i2400m: host/device procotol and core driver definitions
i2400m: documentation and instructions for usage
wimax: Makefile, Kconfig and docbook linkage for the stack
...
This patch creates the new functions
oprofile_write_reserve()
oprofile_add_data()
oprofile_write_commit()
and makes them part of the oprofile api.
Signed-off-by: Robert Richter <robert.richter@amd.com>
The new ring buffer implementation allows the storage of samples with
different size. This patch implements the usage of the new sample
format to store ibs samples in the cpu buffer. Until now, writing to
the cpu buffer could lead to incomplete sampling sequences since IBS
samples were transfered in multiple samples. Due to a full buffer,
data could be lost at any time. This can't happen any more since the
complete data is reserved in advance and then stored in a single
sample.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Special events such as task or context switches are marked with an
escape code in the cpu buffer followed by an event code or a task
identifier. There is one escape code per event. To make escape
sequences also available for data samples the internal cpu buffer
format must be changed. The current implementation does not allow the
extension of event codes since this would lead to collisions with the
task identifiers. To avoid this, this patch introduces an event mask
that allows the storage of multiple events with one escape code. Now,
task identifiers are stored in the data section of the sample. The
implementation also allows the usage of custom data in a sample. As a
side effect the new code is much more readable and easier to
understand.
Signed-off-by: Robert Richter <robert.richter@amd.com>
This is a global variable defined in fsl_booke_mmu.c with a value that gets
initialized in assembly code in head_fsl_booke.S.
It's never used.
If some code ever does want to know the number of entries in TLB1, then
"numcams = mfspr(SPRN_TLB1CFG) & 0xfff", is a whole lot simpler than a
global initialized during kernel boot from assembly.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some assembly code in head_fsl_booke.S hard-coded the size of struct tlbcam
to 20 when it indexed the TLBCAM table. Anyone changing the size of struct
tlbcam would not know to expect that.
The kernel already has a system to get the size of C structures into
assembly language files, asm-offsets, so let's use it.
The definition of the struct gets moved to a header, so that asm-offsets.c
can include it.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Provides a small speedup when accessing pefetchable ranges. To indicate
that a memory range is prefetchable, mark it in the dts file with 42000000
instead of 02000000.
A powepc pci_controller is allowed three memory ranges, any of which may be
prefetchable. However, the PCI-PCI bridge configuration space only has one
field for "non-prefetchable memory behind bridge", which has a 32 bit
address, and one field for "prefetchable memory behind bridge", which may
have a 64 bit address. These are PCI bus addresses, not CPU physical
addresses.
So really you're only allowed one memory range of each type. And if you
want the range at a PCI address above 32 bits you must make it
prefetchable.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The code that sets up the outbound ATMU windows, which is used to map CPU
physical addresses into PCI bus addresses where BARs will be mapped, didn't
work so well.
For one, it leaked the ioremap() of the ATMU registers. Another small bug
was the high 20 bits of the PCI bus address were left as zero. It's legal
for prefetchable memory regions to be above 32 bits, so the high 20 bits
might not be zero.
Mainly, it couldn't handle ranges that were not a power of two in size or
were not naturally aligned. The ATMU windows have these requirements (size
& alignment), but the code didn't bother to check if the ranges it was
programming met them. If they didn't, the windows would silently be
programmed incorrectly.
This new code can handle ranges which are not power of two sized nor
naturally aligned. It simply splits the ranges into multiple valid ATMU
windows. As there are only four windows, pooly aligned or sized ranges
(which didn't even work before) may run out of windows. In this case an
error is printed and an effort is made to disable the unmapped resources.
An improvement that could be made would be to make use of the default
outbound window. Iff hose->pci_mem_offset is zero, then it's possible that
some or all of the ranges might not need an outbound window and could just
use the default window.
The default ATMU window can support a pci_mem_offset less than zero too,
but pci_mem_offset is unsigned. One could say the abilities allowed a
powerpc pci_controller is neither subset nor a superset of the abilities of
a Freescale PCIe controller. Thankfully, the most useful bits are in the
intersection of the two abilities.
Signed-off-by: Trent Piepho <tpiepho@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Fixes compile breakage as linux/byteorder.h was removed.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (171 commits)
Blackfin arch: fix bug - BF527 0.2 silicon has different CPUID (DSPID) value
Blackfin arch: Enlarge flash partition for kenel for bf533/bf537 boards
Blackfin arch: fix bug: kernel crash when enable SDIO host driver
Blackfin arch: Print FP at level KERN_NOTICE
Blackfin arch: drop ad73311 test code
Blackfin arch: update board default configs
Blackfin arch: Set PB4 as the default irq for bf548 board v1.4+.
Blackfin arch: fix typo in early printk bit size processing
Blackfin arch: enable reprogram cclk and sclk for bf518f-ezbrd
Blackfin arch: add SDIO host driver platform data
Blackfin arch: fix bug - kernel stops at initial console
Blackfin arch: fix bug - kernel crash after config IP for ethernet port
Blackfin arch: add sdh support for bf518f-ezbrd
Blackfin arch: fix bug - kernel detects BF532 incorrectly
Blackfin arch: add () to avoid warnings from gcc
Blackfin arch: change HWTRACE Kconfig and set it on default
Blackfin arch: Clean oprofile build path for blackfin
Blackfin arch: remove hardware PM code, oprofile not use it
Blackfin arch: rewrite get_sclk()/get_vco()
Blackfin arch: cleanup and unify the ins functions
...
* git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
avr32: Move syscalls.h under arch/avr32/include/asm/
avr32: Define DIE_OOPS
avr32: Remove DMATEST from defconfigs
arch/avr32: Eliminate NULL test and memset after alloc_bootmem
avr32: data param to at32_add_device_mci() must be non-NULL
atmel-mci: move atmel-mci.h file to include/linux
avr32: Hammerhead board support
avr32: Allow reserving multiple pins at once
favr-32: Remove deprecated call
MIMC200: Remove deprecated call
avr: struct device - replace bus_id with dev_name(), dev_set_name()
avr32: Introducing asm/syscalls.h
* git://git.kernel.org/pub/scm/linux/kernel/git/czankel/xtensa-2.6:
xtensa: Update platform files to reflect new location of the header files.
xtensa: switch to packed struct unaligned access implementation
xtensa: Add xt2000 support files.
xtensa: move headers files to arch/xtensa/include
xtensa: use the new byteorder headers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
pcibios_enable_device() and pcibios_disable_device() don't handle
IRQs for devices that have MSI enabled and it should treat the
devices with MSI-X enabled in the same way.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Since pci_bus has a struct device, use dev_printk directly instead
of faking it by hand.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the sh simple_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the mips common_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the alpha common_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Use the generic pci_swizzle_interrupt_pin() instead of arch-specific code.
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Keep "pin" encoded as it is in the "Interrupt Pin" value in PCI config
space, i.e., 0=device doesn't use interrupts, 1=INTA, ..., 4=INTD.
This makes the bridge INTx swizzle match other architectures.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch makes pci_get_interrupt_pin() return values encoded
the same way as the "Interrupt Pin" value in PCI config space,
i.e., 1=INTA, ..., 4=INTD.
pirq_bios_set() is the only in-tree caller of pci_get_interrupt_pin()
and pci_get_interrupt_pin() is not exported.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: hpa@zytor.com
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Early type 1 accesses can cause problems on some platforms, and
pci=noearly is supposed to prevent them from occurring. However, early
mcfg probing code uses type 1 and isn't protected by a check for
noearly. This patch fixes that problem.
Signed-off-by: Jacob Pan <jacob.jun.pan@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Change PCI bus locality messages so they have a bit more context
and look like the rest of PCI, e.g.,
- bus 01 -> node 0
- bus 04 -> node 0
+ pci 0000:01: bus on NUMA node 0
+ pci 0000:04: bus on NUMA node 0
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
These are easy to trigger (more or less harmlessly) with multiple video
cards, since the ROM BAR will typically not be given any space by the
BIOS bridge setup. No reason to punish quiet boot for this.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Device drivers that use pci_request_regions() (and similar APIs) have a
reasonable expectation that they are the only ones accessing their device.
As part of the e1000e hunt, we were afraid that some userland (X or some
bootsplash stuff) was mapping the MMIO region that the driver thought it
had exclusively via /dev/mem or via various sysfs resource mappings.
This patch adds the option for device drivers to cause their reserved
regions to the "banned from /dev/mem use" list, so now both kernel memory
and device-exclusive MMIO regions are banned.
NOTE: This is only active when CONFIG_STRICT_DEVMEM is set.
In addition to the config option, a kernel parameter iomem=relaxed is
provided for the cases where developers want to diagnose, in the field,
drivers issues from userspace.
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The _OSC capability OSC_EXT_PCI_CONFIG_SUPPORT is set when the root
bridge is added with pci_acpi_osc_support() if we can access PCI
extended config space.
This adds the function pci_ext_cfg_avail which returns true if we can
access PCI extended config space (offset greater than 0xff). It
currently only returns false if arch=x86 and raw_pci_ext_ops is not set
(which might happen if pci=nommcfg is set on the kernel command-line).
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch is part of a larger patch series which will remove
the "char bus_id[20]" name string from struct device. The device
name is managed in the kobject anyway, and without any size
limitation, and just needlessly copied into "struct device".
To set and read the device name dev_name(dev) and dev_set_name(dev)
must be used. If your code uses static kobjects, which it shouldn't
do, "const char *init_name" can be used to statically provide the
name the registered device should have. At registration time, the
init_name field is cleared, to enforce the use of dev_name(dev) to
access the device name at a later time.
We need to get rid of all occurrences of bus_id in the entire tree
to be able to enable the new interface. Please apply this patch,
and possibly convert any remaining remaining occurrences of bus_id.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-Off-By: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Implementation of USB device driver integrated in Freescale's i.MXL
processor.
Adds USB device driver for i.MXL.
Signed-off-by: Darius Augulis <augulis.darius@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move otg_get/set/put_transceiver() from omap specific code
to common otg.c so other upcoming drivers can share them.
[ dbrownell@users.sourceforge.net: move to drivers/usb/otg, dox ]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <me@felipebalbi.com>
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As Russell King points out, calling put_device(otg_transceiver->dev)
directly in driver cleanup paths makes assumptions about otg_transceiver
internals.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A published errata for ppc440epx states, that when running Linux with
both EHCI and OHCI modules loaded, the EHCI module experiences a fatal
error when a high-speed device is connected to the USB2.0, and
functions normally if OHCI module is not loaded.
There used to be recommendation to use only hi-speed or full-speed
devices with specific conditions, when respective module was unloaded.
Later, it was observed that ohci suspend is enough to keep things
going, and it was turned into workaround, as explained below.
Quote from original descriprion:
The 440EPx USB 2.0 Host controller is an EHCI compliant controller. In
USB 2.0 Host controllers, each EHCI controller has one or more companion
controllers, which may be OHCI or UHCI. An USB 2.0 Host controller will
contain one or more ports. For each port, only one of the controllers
is connected at any one time. In the 440EPx, there is only one OHCI
companion controller, and only one USB 2.0 Host port.
All ports on an USB 2.0 controller default to the companion
controller. If you load only an ohci driver, it will have control of
the ports and any deviceplugged in will operate, although high speed
devices will be forced to operate at full speed. When an ehci driver
is loaded, it explicitly takes control of the ports. If there is a
device connected, and / or every time there is a new device connected,
the ehci driver determines if the device is high speed or not. If it
is high speed, the driver retains control of the port. If it is not,
the driver explicitly gives the companion controller control of the
port.
The is a software workaround that uses
Initial version of the software workaround was posted to
linux-usb-devel:
http://www.mail-archive.com/linux-usb-devel@lists.sourceforge.net/msg54019.html
and later available from amcc.com:
http://www.amcc.com/Embedded/Downloads/download.html?cat=1&family=15&ins=2
The patch below is generally based on the latter, but reworked to
powerpc/of_device USB drivers, and uses a few devicetree inquiries to
get rid of (some) hardcoded defines.
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the UCC_GETH_UPSMR_xxx definitions to qe.h. The ucc_geth driver will
eventually use these instead of the UPSMR_ macros it currently defines.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The general pci resume code can only restore part of the
configuration registers. We need to reconfigure those
registers in the FIXUP_RESUME.
Signed-off-by: Jason Jin <Jason.jin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
update bfin-sdh platform data to fix this issue.
Pointed-out-by: Dominik Herwald <d.herwald@dsh-elektronik.de>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
drop ad73311 test code, this can be done easily from userspace
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Bug: Boot kernel in BF533-EZKIT without set ip during boot,
it stops at initial console.
Restore serial platform_device data to fix this issue.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Fix typo - kernel crash on bf533-stamp/bf533-ezkit after config IP for ethernet port
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
fix this typo in this patch
Reported-by: Ben Matthews <mben12@gmail.com>
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
change the hwtrace description to be less confusing and default it to on
(since there shouldnt be any crashes in the miss handler code itself)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
rewrite get_sclk()/get_vco() based on the assumption sclk/vco never
changes (since today it cannot)
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- handle bf531/bf532/bf534/bf536 variants in ipipe.h
- cleanup IPIPE logic for bfin_set_irq_handler()
- cleanup ipipe asm code a bit and add missing ENDPROC()
- simplify IPIPE code in trap_c
- unify some of the IPIPE code and fix style
- simplify DO_IRQ_L1 handling with ipipe code
- revert IRQ_SW_INT# addition from ipipe merge
- remove duplicate get_{c,s}clk() prototypes
]
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Grace Pan <grace.pan@analog.com>: Add case for kgdb test in l1 and l2]
Signed-off-by: Grace Pan <grace.pan@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
This is a mixture ofcMichael McTernan's patch and the existing cplb-mpu code.
We ditch the old cplb-nompu implementation, which is a good example of
why a good algorithm in a HLL is preferrable to a bad algorithm written in
assembly. Rather than try to construct a table of all posible CPLBs and
search it, we just create a (smaller) table of memory regions and
their attributes. Some of the data structures are now unified for both
the mpu and nompu cases. A lot of needless complexity in cplbinit.c is
removed.
Further optimizations:
* compile cplbmgr.c with a lot of -ffixed-reg options, and omit saving
these registers on the stack when entering a CPLB exception.
* lose cli/nop/nop/sti sequences for some workarounds - these don't
* make
sense in an exception context
Additional code unification should be possible after this.
[Mike Frysinger <vapier.adi@gmail.com>:
- convert CPP if statements to C if statements
- remove redundant statements
- use a do...while loop rather than a for loop to get slightly better
optimization and to avoid gcc "may be used uninitialized" warnings ...
we know that the [id]cplb_nr_bounds variables will never be 0, so this
is OK
- the no-mpu code was the last user of MAX_MEM_SIZE and with that rewritten,
we can punt it
- add some BUG_ON() checks to make sure we dont overflow the small
cplb_bounds array
- add i/d cplb entries for the bootrom because there is functions/data in
there we want to access
- we do not need a NULL trailing entry as any time we access the bounds
arrays, we use the nr_bounds variable
]
Signed-off-by: Michael McTernan <mmcternan@airvana.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
If we are running on a chip revision below what we are compiled for,
there will be missing anomaly workarounds, and a panic is inevitable. Do
is sooner, rather than later, so people don't look for bugs that already
have workarounds (that they turned off).
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
do not allow people to pass in a diff clkin_hz value when
reprogramming clocks -- it is too late currently
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
rather than use *(unsigned int *)v everywhere, do this once with a local
cpu_num variable
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
It should be 'lose', not 'loose'.
Signed-off-by: Nick Andrew <nick@nick-andrew.net>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
cannot simply OR the ndsize ... need to clear out the old value first
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Michael says that some bugs are crashes in tcp_v4_send_reset.
There's a missing clobber of "CC" in our checksum assembly
statement; fixing this makes the generated code look much saner.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
push cache flushing up to dma_memcpy() so that we call the flush
functions just once
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
move most dma functions into static inlines since they are vastly 1
liners that get/set a value in a structure
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
set_dma_callback: do not store .irq if request_irq() failed so we dont
turn around and attempt to free_irq() it later on in free_dma()
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- unify all dma in/out functions (takes ~35 lines of code now)
- unify dma_memcpy with dma in/out functions (1 place that touches MDMA0
registers)
- add support for 32bit transfers
- cleanup dma_memcpy code to be much more readable
- irqs are disabled only while programming MDMA registers rather than
the entire transaction
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Check pointers in safe_dma_memcpy as this is the entry point for user-space code
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
All slaves I'm aware of should support at least 100kHz
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
This device shouldn't be considered as an alternative to a Memory Mapped
or built-in Ethernet MAC. Throughput is slow (~460kByte/s) while generating
a very high system load (~60%).
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Fix a few problems I discovered when building a kernel with upstream CVS
binutils.
We have to add the NOTES macro to our linker script, since a kernel
built with --build-id is otherwise unable to boot. Last time NOTES was
added, it broke things, but the definition of the macro has changed not
to rely on parts of the linker script that aren't present on Blackfin.
I also noticed that _l2_lma_start does not point into the kernel image,
but rather somewhere in L1/L2 space, which seems unintended. Also, when
the L2 section was added to the linker script, the part following it which
computes then length of the init section was not updated.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Remove all traces of the relocation stack. It's been removed from
binutils for years now.
Add a sanity overflow check to pcrel24 relocations to catch modules that
were built without -mlong-calls.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Tweak the BUG_ON() check to allow for equal values since the way pos is
handled ... it is always indexed and post incremented
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
use scm changelog rather than comment blocks in files
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- remove duplicated code and headers
- add option allowing arbitrary SDRAM/DDR Timing parameters.
- mark automatically calculated timings as EXPERIMENTAL
- fix comment header block
Related to BUGs:
- kernel boot up fails with CONFIG_BFIN_KERNEL_CLOCK item on.
- kernel does not boot if re-program clocks
[ Mike Frysinger <vapier.adi@gmail.com>
- fix comment header
- mark do_sync static
- document the DMA shutdown
- simplify SIC_IWR handling
- fix ANOMALY_05000265 handling to work as intended ]
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- use KERN_NOTICE when using gpios as both irq and non
rather than KERN_ERR
- embedded newlines in printk() does not fly]
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Mark the function local_allocate_threshold_blocks() with __cpuinit,
in order to remove the following section mismatch messages:
WARNING: arch/x86/kernel/cpu/mcheck/built-in.o(.text+0x1363): Section mismatch in reference from the function local_allocate_threshold_blocks() to the function .cpuinit.text:allocate_threshold_blocks()
The function local_allocate_threshold_blocks() references
the function __cpuinit allocate_threshold_blocks().
This is often because local_allocate_threshold_blocks lacks a __cpuinit
annotation or the annotation of allocate_threshold_blocks is wrong.
WARNING: arch/x86/kernel/cpu/built-in.o(.text+0x1def): Section mismatch in reference from the function local_allocate_threshold_blocks() to the function .cpuinit.text:allocate_threshold_blocks()
The function local_allocate_threshold_blocks() references
the function __cpuinit allocate_threshold_blocks().
This is often because local_allocate_threshold_blocks lacks a __cpuinit
annotation or the annotation of allocate_threshold_blocks is wrong.
WARNING: arch/x86/kernel/built-in.o(.text+0xef2b): Section mismatch in reference from the function local_allocate_threshold_blocks() to the function .cpuinit.text:allocate_threshold_blocks()
The function local_allocate_threshold_blocks() references
the function __cpuinit allocate_threshold_blocks().
This is often because local_allocate_threshold_blocks lacks a __cpuinit
annotation or the annotation of allocate_threshold_blocks is wrong.
All the callsites of this function are __cpuinit already, and all the
functions it calls are __cpuinit as well.
Signed-off-by: Leonardo Potenza <lpotenza@inwind.it>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CONFIG_FRAME_POINTERS=y results in much better debug info for the
kernel (clear and precise backtraces), with the only drawback being
a ~1% increase in kernel size.
So offer it unconditionally and enable it by default.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
