As of edbc454 [mtd: driver _read() returns max_bitflips; mtd_read()
returns -EUCLEAN], 'mtd->bitflip_threshold' must be set for mtd devices
having ECC, prior any 'mtd_read()' call.
Otherwise, 'mtd_read()' will falsely return -EUCLEAN.
Normally, 'mtd->bitflip_threshold' is initialized when the MTD is added.
However, this is too late for NAND MTDs, as 'scan_bbt()' is invoked
prior the existing initialization of 'mtd->bitflip_threshold'.
This is a problem since 'scan_bbt()' calls 'mtd_read()', in the case
of a flash-based bad block table.
It resulted in a falsely reported bitflips indication during BBT read,
which lead to constant scrubbing of the flash BBT blocks.
Initialize 'mtd->bitflip_threshold' to its default value (if not already
set by the driver), prior to invocation of 'scan_bbt()'.
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Commit "62f38455 UBI: modify ubi_wl_flush function to clear work queue for a lnum"
takes the 'work_sem' semaphore in write mode for the entire loop, which is not
very good because it will block other workers for potentially long time. We do
not need to have it in write mode - read mode is enough, and we do not need to
hole it over the entire loop. So this patch turns changes the locking: takes
'work_sem' in read mode and pushes it down to the loop.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Commit "aa44d1d UBI: remove Kconfig debugging option" broke UBI and it
refuses to initialize if debugfs (CONFIG_DEBUG_FS) is disabled. I incorrectly
assumed that debugfs files creation function will return success if debugfs
is disabled, but they actually return -ENODEV. This patch fixes the issue.
Reported-by: Paul Parsons <lost.distance@yahoo.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Tested-by: Paul Parsons <lost.distance@yahoo.com>
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAk/JG1wACgkQdwG7hYl686M80wCglN4kutx20j+KJWuZofkr9Hog
weEAoI4jrqEWEdW9EcT2CIWQw7eG+1v+
=7tdo
-----END PGP SIGNATURE-----
Merge tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd
Pull mtd update from David Woodhouse:
- More robust parsing especially of xattr data in JFFS2
- Updates to mxc_nand and gpmi drivers to support new boards and device tree
- Improve consistency of information about ECC strength in NAND devices
- Clean up partition handling of plat_nand
- Support NAND drivers without dedicated access to OOB area
- BCH hardware ECC support for OMAP
- Other fixes and cleanups, and a few new device IDs
Fixed trivial conflict in drivers/mtd/nand/gpmi-nand/gpmi-nand.c due to
added include files next to each other.
* tag 'for-linus-3.5-20120601' of git://git.infradead.org/linux-mtd: (75 commits)
mtd: mxc_nand: move ecc strengh setup before nand_scan_tail
mtd: block2mtd: fix recursive call of mtd_writev
mtd: gpmi-nand: define ecc.strength
mtd: of_parts: fix breakage in Kconfig
mtd: nand: fix scan_read_raw_oob
mtd: docg3 fix in-middle of blocks reads
mtd: cfi_cmdset_0002: Slight cleanup of fixup messages
mtd: add fixup for S29NS512P NOR flash.
jffs2: allow to complete xattr integrity check on first GC scan
jffs2: allow to discriminate between recoverable and non-recoverable errors
mtd: nand: omap: add support for hardware BCH ecc
ARM: OMAP3: gpmc: add BCH ecc api and modes
mtd: nand: check the return code of 'read_oob/read_oob_raw'
mtd: nand: remove 'sndcmd' parameter of 'read_oob/read_oob_raw'
mtd: m25p80: Add support for Winbond W25Q80BW
jffs2: get rid of jffs2_sync_super
jffs2: remove unnecessary GC pass on sync
jffs2: remove unnecessary GC pass on umount
jffs2: remove lock_super
mtd: gpmi: add gpmi support for mx6q
...
Since commit 6a918bade9, the mxc_nand driver
fails with:
Driver must set ecc.strength when using hardware ECC
This is because nand_scan_tail checks for correct ecc strength
settings, so we must set them up before nand_scan_tail.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org [3.4+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The 'mtd_writev' interface calls the function assigned
to the '_write' field of a given mtd device if that is
not NULL. The block2mtd driver sets the '_writev' field
to the 'mtd_writev' function itself and thus causes a
endless loop.
This is caused by 1dbebd3256
(mtd: harmonize mtd_writev usage).
Remove the assignment from the block2mtd driver to fix the
issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@kernel.org [3.3+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix an issue which was introduced by the recent addition of ecc.strength.
The ecc.strength wasn't set in gpmi-nand, resulting in the following crash:
[ 2.550000] kernel BUG at drivers/mtd/nand/nand_base.c:3347!
...
[ 2.550000] [<c020841c>] (nand_scan_tail+0x328/0x650) from [<c02f68e0>] (gpmi_nand_probe+0x43c/0x5a4)
[ 2.550000] [<c02f68e0>] (gpmi_nand_probe+0x43c/0x5a4) from [<c01f6618>] (platform_drv_probe+0x14/0x18)
[ 2.550000] [<c01f6618>] (platform_drv_probe+0x14/0x18) from [<c01f55b0>] (driver_probe_device+0x74/0x1fc)
[ 2.550000] [<c01f55b0>] (driver_probe_device+0x74/0x1fc) from [<c01f57cc>] (__driver_attach+0x94/0x98)
[ 2.550000] [<c01f57cc>] (__driver_attach+0x94/0x98) from [<c01f3d40>] (bus_for_each_dev+0x50/0x80)
[ 2.550000] [<c01f3d40>] (bus_for_each_dev+0x50/0x80) from [<c01f4e18>] (bus_add_driver+0x188/0x25c)
[ 2.550000] [<c01f4e18>] (bus_add_driver+0x188/0x25c) from [<c01f5a70>] (driver_register+0x78/0x138)
[ 2.550000] [<c01f5a70>] (driver_register+0x78/0x138) from [<c043dc7c>] (gpmi_nand_init+0xc/0x30)
[ 2.550000] [<c043dc7c>] (gpmi_nand_init+0xc/0x30) from [<c0008824>] (do_one_initcall+0x108/0x17c)
[ 2.550000] [<c0008824>] (do_one_initcall+0x108/0x17c) from [<c042a8b8>] (kernel_init+0xfc/0x1bc)
[ 2.550000] [<c042a8b8>] (kernel_init+0xfc/0x1bc) from [<c000fab4>] (kernel_thread_exit+0x0/0x8)
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
MTD_OF_PARTS and the default setting is not working due to using 'Y'
instead of 'y', introduced in commit
d6137badef. This made our board, and
possibly other boards using DTS defined partitions and not having
CONFIG_MTD_OF_PARTS=y defined in the defconfig, fail to mount root.
Signed-off-by: Frank Svendsboe <frank.svendsboe@gmail.com>
Cc: stable@kernel.org [3.2+]
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
It seems there is a bug in scan_read_raw_oob() in nand_bbt.c which
should cause wrong functioning of NAND_BBT_SCANALLPAGES option.
Artem: the patch did not apply and I had to amend it a bit.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: stable@kernel.org
Corner case reads do not work, and return false data and
ECC. This case is typically seen in a ubifs usage, with a
read of type:
- docg3 docg3: doc_read_oob(from=14882415, mode=1,
data=(c30eca40:12), oob=( (null):0))
This results in the following reads:
- docg3 docg3: doc_read_data_area(buf= (null), len=111)
- docg3 docg3: doc_read_data_area(buf=c30eca40, len=12)
- docg3 docg3: doc_read_data_area(buf= (null), len=389)
- docg3 docg3: doc_read_data_area(buf= (null), len=0)
- docg3 docg3: doc_read_data_area(buf= (null), len=16)
If we suppose that the pages content is :
- bytes 0 .. 111 : 0x0a
- bytes 112 .. 255 : 0x0f
Then the returned bytes will be :
- 111 times 0x0a (correct)
- 0x0a 2 times and 0x0f 10 times (incorrect, should be
0x0a,0x0f)
- 0x0f 389 times (correct)
- nothing
- correct OOB
The reason seams that the first 111 bytes read ends between
the 2 docg3 planes, and that the first following read (in
the 12 bytes sequence, read of 16 bit word) returns the byte
of the rightmost plane duplicated in high and lower byte of
the word.
Fix this behaviour by ensuring that if the previous read
ended up in-between the 2 planes, there will be a first 1
byte read to get back to the beginning of leftmost plane.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The new clock subsystem was merged in linux-3.4 without any users, this
now moves the first three platforms over to it: imx, mxs and spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that require
these changes, in order to avoid interdependencies and conflicts.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=rwFF
-----END PGP SIGNATURE-----
Merge tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc clock driver changes from Olof Johansson:
"The new clock subsystem was merged in linux-3.4 without any users,
this now moves the first three platforms over to it: imx, mxs and
spear.
The series also contains the changes for the clock subsystem itself,
since Mike preferred to have it together with the platforms that
require these changes, in order to avoid interdependencies and
conflicts."
Fix up trivial conflicts in arch/arm/mach-kirkwood/common.c (code
removed in one branch, added OF support in another) and
drivers/dma/imx-sdma.c (independent changes next to each other).
* tag 'clock' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (97 commits)
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
SPEAr: Update defconfigs
SPEAr: Add SMI NOR partition info in dts files
SPEAr: Switch to common clock framework
SPEAr: Call clk_prepare() before calling clk_enable
SPEAr: clk: Add General Purpose Timer Synthesizer clock
SPEAr: clk: Add Fractional Synthesizer clock
SPEAr: clk: Add Auxiliary Synthesizer clock
SPEAr: clk: Add VCO-PLL Synthesizer clock
SPEAr: Add DT bindings for SPEAr's timer
ARM i.MX: remove now unused clock files
ARM: i.MX6: implement clocks using common clock framework
ARM i.MX35: implement clocks using common clock framework
ARM i.MX5: implement clocks using common clock framework
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
...
* Always support xattrs (remove the Kconfig option)
* Always support debugging (remove the Kconfig option)
* A fix for a memory leak on error path
* A number of clean-ups
UBI:
* Always support debugging (remove the Kconfig option)
* Remove "data type" hint support
* Huge amount of renames to prepare for the fastmap wor
* A lot of clean-ups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=+6Qi
-----END PGP SIGNATURE-----
Merge tag 'upstream-3.5-rc1' of git://git.infradead.org/linux-ubifs
Pull UBI and UBIFS updates from Artem Bityutskiy:
UBIFS:
* Always support xattrs (remove the Kconfig option)
* Always support debugging (remove the Kconfig option)
* A fix for a memory leak on error path
* A number of clean-ups
UBI:
* Always support debugging (remove the Kconfig option)
* Remove "data type" hint support
* Huge amount of renames to prepare for the fastmap wor
* A lot of clean-ups
* tag 'upstream-3.5-rc1' of git://git.infradead.org/linux-ubifs: (54 commits)
UBI: modify ubi_wl_flush function to clear work queue for a lnum
UBI: introduce UBI_ALL constant
UBI: add lnum and vol_id to struct ubi_work
UBI: add volume id struct ubi_ainf_peb
UBI: add in hex the value for UBI_INTERNAL_VOL_START to comment
UBI: rename scan.c to attach.c
UBI: remove scan.h
UBI: rename UBI_SCAN_UNKNOWN_EC
UBI: move and rename attach_by_scanning
UBI: rename _init_scan functions
UBI: amend comments after all the renamings
UBI: rename ubi_scan_leb_slab
UBI: rename ubi_scan_move_to_list
UBI: rename ubi_scan_destroy_ai
UBI: rename ubi_scan_get_free_peb
UBI: rename ubi_scan_rm_volume
UBI: rename ubi_scan_find_av
UBI: rename ubi_scan_add_used
UBI: remove unused function
UBI: make ubi_scan_erase_peb static and rename
...
Pull trivial updates from Jiri Kosina:
"As usual, it's mostly typo fixes, redundant code elimination and some
documentation updates."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (57 commits)
edac, mips: don't change code that has been removed in edac/mips tree
xtensa: Change mail addresses of Hannes Weiner and Oskar Schirmer
lib: Change mail address of Oskar Schirmer
net: Change mail address of Oskar Schirmer
arm/m68k: Change mail address of Sebastian Hess
i2c: Change mail address of Oskar Schirmer
net: Fix tcp_build_and_update_options comment in struct tcp_sock
atomic64_32.h: fix parameter naming mismatch
Kconfig: replace "--- help ---" with "---help---"
c2port: fix bogus Kconfig "default no"
edac: Fix spelling errors.
qla1280: Remove redundant NULL check before release_firmware() call
remoteproc: remove redundant NULL check before release_firmware()
qla2xxx: Remove redundant NULL check before release_firmware() call.
aic94xx: Get rid of redundant NULL check before release_firmware() call
tehuti: delete redundant NULL check before release_firmware()
qlogic: get rid of a redundant test for NULL before call to release_firmware()
bna: remove redundant NULL test before release_firmware()
tg3: remove redundant NULL test before release_firmware() call
typhoon: get rid of redundant conditional before all to release_firmware()
...
While we generally attempt to get rid of board specific files and replace
them with device tree based descriptions, a lot of platforms have not
come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination of
DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPueuIAAoJEIwa5zzehBx3VvAP/32RkCrrLCQoibsczjwDPQir
ryyT/lom005tlkXFOz9SFirlyNAn0kpDuj0xZ/HL2KgZ0FPlG0OUSRBJJvLZF2vT
qlhf3PqnM1d2Ui6+/QdU/EJyzNkMAtajgTSvp4zDZayoNomO/VTZhW0feRYChUIl
bJx7hnFA9VXnkhORzh9+HhKwVcdhU2R1/LMDUlYxKNnFdF0/kFgw4Gkj4MnmFlyy
NpeLP4H95SeFhKPvmXB/2lZroaRn6wCxhPhUCHShxsH3YFy0J7zaEnmHMFSOX24n
++6fyb0mqiJtZPwJVbF+snb/5hP4epbmkrU5+mqtDdK8HHowAsV0ScKki0wGGmka
Im5ryCMB+NZOD57XGajkpeQGZT+m0S8NilsZ5dy75o7el7WxnMLuUMyjlIbtnfet
3KRF22XnsyPuvldoej/RM1Eiz86qUFl3LPO63cYT+/c9aSw0+luMp+JZp+iOcAr3
xqyiciwOTu6CIP+DnYV72CuFa2IvLA06Eb3pgtpRUwATzS9weQ33X4Q80RaUVKxX
VfXxCcDFl7dfGwqO6HujbxI6oHmEmvBEF9eGmFW2ocVrKnWUmjlC6y9tQxfReQDV
SZkXKEkWPo/MLFl/AM+hTjGyu88ofOG4Vos0t3YmVyTuXekpPFb2DbPCvwnFdv8N
kX/bfsxWPBDl3EdCQU8y
=wkmj
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific changes from Olof Johansson:
"While we generally attempt to get rid of board specific files and
replace them with device tree based descriptions, a lot of platforms
have not come that far:
In shmobile, we add two new board files because their recently started
effort to add DT support has not proceeded enough to use it for all of
the important hardware.
In Kirkwood, we are adding support for new boards with a combination
of DT and board file contents in multiple cases.
pxa/mmp and imx are extending support for existing board files but not
adding new ones."
Fix up trivial conflicts in arch/arm/mach-{mmp/ttc_dkb.c,shmobile/{Kconfig,Makefile}}
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: shmobile: fix smp build
ARM: kirkwood: Add support for RaidSonic IB-NAS6210/6220 using devicetree
kirkwood: Add iconnect support
orion/kirkwood: create a generic function for gpio led blinking
kirkwood/orion: fix orion_gpio_set_blink
ARM: kirkwood: Define DNS-320/DNS-325 NAND in fdt
kirkwood: Allow nand to be configured via. devicetree
mtd: Add orion_nand devicetree bindings
ARM: kirkwood: Basic support for DNS-320 and DNS-325
ARM: mach-shmobile: Use DT_MACHINE for armadillo 800 eva
ARM: mach-shmobile: Use DT_MACHINE for KZM9G
ARM: pxa: hx4700: Add Synaptics NavPoint touchpad
ARM: pxa: Use REGULATOR_SUPPLY macro
ARM: mach-shmobile: kzm9g: enable SMP boot
ARM: mach-shmobile: kzm9g: defconfig update
ARM: mach-shmobile: kzm9g: add PCF8757 gpio-key
ARM: mach-shmobile: kzm9g: add SDHI support
ARM: mach-shmobile: kzm9g: add MMCIF support
ARM: mach-shmobile: kzm9g: correct screen direction
ARM: mach-shmobile: sh73a0.h: add GPIO_NR
...
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
These cleanups are basically all over the place. The idea is to collect
changes with minimal impact but large number of changes so we can avoid
them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Hcjs
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull first batch of arm-soc cleanups from Olof Johansson:
"These cleanups are basically all over the place. The idea is to
collect changes with minimal impact but large number of changes so we
can avoid them from distracting in the diffstat in the other series.
A significant number of lines get removed here, in particular because
the ixp2000 and ixp23xx platforms get removed. These have never been
extremely popular and have fallen into disuse over time with no active
maintainer taking care of them. The u5500 soc never made it into a
product, so we are removing it from the ux500 platform.
Many good cleanups also went into the at91 and omap platforms, as has
been the case for a number of releases."
Trivial modify-delete conflicts in arch/arm/mach-{ixp2000,ixp23xx}
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (152 commits)
ARM: clps711x: Cleanup IRQ handling
ARM clps711x: Removed unused header mach/time.h
ARM: clps711x: Added note about support EP731x CPU to Kconfig
ARM: clps711x: Added missing register definitions
ARM: clps711x: Used own subarch directory for store header file
Dove: Fix Section mismatch warnings
ARM: orion5x: ts78xx debugging changes
ARM: orion5x: remove PM dependency from ts78xx
ARM: orion5x: ts78xx fix NAND resource off by one
ARM: orion5x: ts78xx whitespace cleanups
Orion5x: Fix Section mismatch warnings
Orion5x: Fix warning: struct pci_dev declared inside paramter list
ARM: clps711x: Combine header files into one for clps711x-targets
ARM: S3C24XX: Use common macro to define resources on mach-qt2410.c
ARM: S3C24XX: Use common macro to define resources on mach-osiris.c
ARM: EXYNOS: Adapt to cpuidle core time keeping and irq enable
ARM: S5PV210: Use common macro to define resources on mach-smdkv210.c
ARM: S5PV210: Use common macro to define resources on dev-audio.c
ARM: S5PC100: Use common macro to define resources on dev-audio.c
ARM: S5P64X0: Use common macro to define resources on dev-audio.c
...
This patch modifies ubi_wl_flush to force the erasure of
particular volume id / logical eraseblock number pairs. Previous functionality
is preserved when passing UBI_ALL for both values. The locations where ubi_wl_flush
were called are appropriately changed: ubi_leb_erase only flushes for the
erased LEB, and ubi_create_volume forces only flushing for its volume id.
External code can call this new feature via the new function ubi_flush() added
to kapi.c, which simply passes through to ubi_wl_flush().
This was tested by disabling the call to do_work in ubi thread, which results
in the work queue remaining unless explicitly called to remove. UBIFS was
changed to call ubifs_leb_change 50 times for four different LEBs. Then the
new function was called to clear the queue: passing wrong volume ids / lnum,
correct ones, and finally UBI_ALL for both to ensure it was finally all
cleard. The work queue was dumped each time and the selective removal
of the particular LEB numbers was observed. Extra checks were enabled and
ubifs's integck was also run. Finally, the drive was repeatedly filled and
emptied to ensure that the queue was cleared normally.
Artem: amended the patch.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Joel will use it in his 'ubi_flush()' extention to specify all eraseblocks.
Also amend the comment for UBI_UNKNOWN - it is used beyond attaching info
structure now.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This is part of a multipart patch to allow UBI to force the erasure of
particular logical eraseblock numbers. In this patch, the volume id and LEB
number are added to ubi_work data structure, and both are also passed as a
parameter to schedule erase to set it appropriately. Whenever ubi_wl_put_peb
is called, the lnum is also passed to be forwarded to schedule erase. Later,
a new ubi_sync_lnum will be added to execute immediately all work related to
that lnum.
This was tested by outputting the vol_id and lnum during the schedule of
erasure. The ubi thread was disabled and two ubifs drives on separate
partitions repeated changed a small number of LEBs. The ubi module was readded,
and all the erased LEBs, corresponding to the volumes, were added to the
schedule erase queue.
Artem: minor tweaks
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch adds the volume id to struct ubi_ainf_peb when scanning the LEBs at
startup. PEBs now added to the erase queue will know their original LEB number
and volume id, if available, and will be -1 otherwise (for instance, if the VID
header is unreadable).
This was tested by creating an ubi device with 3 volumes and disabiling the
ubi_thread's do_work functionality. The different ubi volumes were formatted
to ubifs and had files created and erased. The ubi modules was reloaded and
the list of LEB's added to the erased list was outputted, confirming the
volume ids and LEB numbers were appropriate.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Explicitly provide the first internal volume ID value in the comment for
UBI_INTERNAL_VOL_START. This allows developers who, when adding features
related to volume ids and observe unexpected very large volume ids, to grep
for the observed value in the source code and find out immediately that it is
expected behaviour.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Finally, rename the scan.c file. Now adding fastmap support won't look that
hacky anymore.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This file is small and it does not make sense to have it separate from where
everything else lives, so merge it with ubi.h.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Rename the constant to UBI_UNKNOWN, for the same reason that we are going
to add nother attaching method and re-use the same data structures, so the
"SCAN" in the name becomes incorrect. I've also removed the "_EC" part because
Joel is going to use this constant for other fields in the attaching info data
structures.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Rename the 'attach_by_scanning()' function to 'ubi_attach()' and move it to
scan.c. Richard will plug his fastmap stuff there.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We have a couple of initialization funcntionsn left which have "_scan" suffic -
rename them:
ubi_eba_init_scan() -> ubi_eba_init()
ubi_wl_init_scan() -> ubi_wl_init()
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch amends commentaries in scan.[ch] to match the new logic. Reminder -
we did the restructuring to prepare the code for adding the fastmap. This patch
also renames a couple of functions - it was too difficult to separate out that
change and I decided that it is not too bad to have it in the same patch with
commentaries changes.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The 'ubi_scan_erase_peb()' is used only in scan.c so can be static. Also
re-name it to 'early_erase_peb()' because we tend to use "ubi_" prefix only for
non-static fuction and also because the new name is better.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
After re-naming the 'struct ubi_scan_volume' we should adjust all variables
named 'sv' to something else, because 'sv' stands for "scanning volume".
Let's rename it to 'av' which stands for "attaching volume" which is
a bit more consistent and has the same length, which makes re-naming easy.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
After re-naming the 'struct ubi_scan_info' we should adjust all variables
named 'si' to something else, because 'si' stands for "scanning info".
Let's rename it to 'ai' which stands for "attaching info" which is
a bit more consistent and has the same length, which makes re-naming easy.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
After re-naming the 'struct ubi_scan_leb' we should adjust all variables
named 'seb' to something else, because 'seb' stands for "scanning eraseblock".
Let's rename it to 'aeb' which stands for "attaching eraseblock" which is
a bit more consistend and has the same length.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Now some commentaries are out-of-date, after we re-named the data
structures - amend them.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Rename 'struct ubi_scan_info' to 'struct ubi_attach_info'. This is part
of the code re-structuring I am trying to do in order to add fastmap
in a more logical way. Fastmap can share a lot with scanning, including
the attach-time data structures, which all now have "scan" word in the
name. Let's get rid of this word.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Rename 'struct ubi_scan_volume' to 'struct ubi_ainf_volume'. This is part
of the code re-structuring I am trying to do in order to add fastmap
in a more logical way. Fastmap can share a lot with scanning, including
the attach-time data structures, which all now have "scan" word in the
name. Let's get rid of this word and use "ainf" instead which stands
for "attach information". It has the same length as "scan" so re-naming
is trivial.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Rename 'struct ubi_scan_leb' to 'struct ubi_ainf_leb'. This is part
of the code re-structuring I am trying to do in order to add fastmap
in a more logical way. Fastmap can share a lot with scanning, including
the attach-time data structures, which all now have "scan" word in the
name. Let's get rid of this word and use "ainf" instead which stands
for "attach information". It has the same length as "scan" so re-naming
is trivial.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
This patch removes the 'dbg_err()' macro and we now use 'ubi_err' instead.
The idea of 'dbg_err()' was to compile out some error message to make the
binary a bit smaller - but I think it was a bad idea.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We have the "sefl-check" feature in UBI, but for historical reasons many
corresponding functions and commentaries in the code use term "paranoid check"
instead. Let's clean this up and use "self-check" everywhere.
This patch renames functions, amends messages and kills several redundant
debugging messages.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We have the "sefl-check" feature in UBI, but for historical reasons many
corresponding functions and commentaries in the code use term "paranoid check"
instead. Let's clean this up and use "self-check" everywhere.
This patch renames functions, amends comments and messages. It touches only the
io.c file.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch kills the UBI debugging Kconfig option completely and makes all the
debugging stuff to be always compiled-in. It was pain in the neck to maintain
this useless option because all users I am aware of have debugging enabled
anyway - how else will you diagnose errors otherwise?
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_mkvol_req()' to 'ubi_dump_mkvol_req()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_seb()' to 'ubi_dump_seb()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_sv()' to 'ubi_dump_sv()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_vtbl_record()' to 'ubi_dump_vtbl_record()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_vol_info()' to 'ubi_dump_vol_info()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Richard removed the "dtype" hint, but few commentaries were left and this patch
removes them. I've also added a better description about the "dtype" field in
the ubi-user.h for people who may ever wonder what was that dtype thing about.
This patch also adds an important note that it is better to use value "3" for
the "dtype" field.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We do not need this feature and to our shame it even was not working
and there was a bug found very recently.
-- Artem Bityutskiy
Without the data type hint UBI2 (fastmap) will be easier to implement.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently UBI silently retries I/O operation in case of errors. This patch
makes it emit a warning before retrying. This should allow users notice issues
earlier.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
UBI (and UBIFS) are a bit over-engineered WRT debugging. The idea was to
link as few as possible when debugging is disabled, but the downside is
that most people produce bug reports which are difficult to understand.
Always dump the VID and EC headers' contents in case of errors when it
is helpful.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
UBI (and UBIFS) are a bit over-engineered WRT debugging. The idea was to
link as few as possible when debugging is disabled, but the downside is
that most people produce bug reports which are difficult to understand.
Always dump the flash contents in case of errors, not only when debugging is
enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
UBI (and UBIFS) are a bit over-engineered WRT debugging. The idea was to
link as few as possible when debugging is disabled, but the downside is
that most people produce bug reports which are difficult to understand.
This patch weeds out the 'ubi_dbg_dump_stack()' function and turns it
into 'dump_stack()' - it is always useful to have stack dump in case of
an error.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Fix following compile error caused by commit 39febc0 (mtd: nand: gpmi:
adopt pinctrl support).
CC drivers/mtd/nand/gpmi-nand/gpmi-nand.o
drivers/mtd/nand/gpmi-nand/gpmi-nand.c: In function ‘acquire_resources’:
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:499:45: error: ‘pdev’ undeclared (first use in this function)
Reported-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allow a NAND chip using the orion_nand driver to be described using devicetree.
Changes since last submission (V4) [Addressing comments by]:-
* WARN when bank-width is out of range [Andrew Lunn]
Changes since last submission (V3):-
* Document all parameters [Grant Likely]
* Convert bank-width to be in bytes
* Add explicit defaults for cle, ale and bank-width
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Spansion S29NS512P flash uses a 16bit transfer to report number
of sectors instead of two 8bit accesses as CFI specifies.
Artem: remove warning message which said that we are applying the
fixup - no need to scary the user unnecessarily.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Two modes are supported: 4-bit and 8-bit error correction.
Note that 4-bit mode is only confirmed to work on OMAP3630 ES 1.x,
x >= 1. The OMAP3 GPMC hardware BCH engine computes remainder
polynomials, it does not provide automatic error location and
correction: this step is implemented using the BCH library.
This implementation only protects page data, there is no support
for protecting user-defined spare area bytes (this could be added
with few modifications); therefore, it cannot be used with YAFFS2
or other similar filesystems that depend on oob storage.
Before being stored to nand flash, hardware BCH ecc is adjusted
so that an erased page has a valid ecc; thus allowing correction of
bitflips in blank pages (also common on 4-bit devices).
BCH correction mode is selected at runtime by setting platform data
parameter 'ecc_opt' to value OMAP_ECC_BCH4_CODE_HW or
OMAP_ECC_BCH8_CODE_HW.
This code has been tested with mtd test modules, UBI and UBIFS on a
BeagleBoard revC3 (OMAP3530 ES3.0 + Micron NAND 256MiB 1,8V 16-bit).
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Apparently, there is an implementor of 'read_oob' which may return an
error inidication (e.g. docg4_read_oob may return -EIO).
Test the return value of 'read_oob/read_oob_raw', and if negative,
propagate the error, so it's returned by the '_read_oob' interface.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As of [mtd: nand: remove autoincrement 'sndcmd' code], the
NAND_CMD_READ0 command is issued unconditionally.
Thus, read_oob/read_oob_raw's 'sndcmd' argument is no longer needed, as
well as their return code.
Remove the 'sndcmd' parameter, and set the return code to 0.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Winbond W25Q80BW is a 8Mbit serial flash memory device.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch just adds the DT support to gpmi-nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read/write OOB if the caller doesn't require it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read OOB if the caller didn't request it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read OOB if the caller doesn't require it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read OOB if the caller doesn't require it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We now have an interface for notifying the nand_ecc_ctrl functions when OOB
data must be returned to the upper layers and when it may be left untouched.
This patch fills in the 'oob_required' parameter properly from
nand_do_{read,write}_ops. When utilized properly in the lower layers, this
parameter can improve performance and/or reduce complexity for NAND HW and SW
that can simply avoid transferring the OOB data.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).
This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.
Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.
Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.
[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Lantiq SoCs have a External Bus Unit (EBU) that is used to attach MTD media.
As we need to co-exist with PCI on the same bus, certain swapping settings must
be applied. Similar to the NOR map driver we need to apply a fix to make NAND
work. The easiest way is to use byte reads.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch sets the of_match_table field inside plat_nand's platform_driver.
We also add a struct mtd_part_parser_data pointer to make sure of_part parsing
works.
If an arch wants to support plat_nand via DT it needs to setup the
platform_nand_data and hook it into the platform_device.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the id and sector mappings for mx25l2005a flash chips.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND_NO_AUTOINCR option is always set, so we will kill the option and make
"no autoincrement" the default behavior for nand_base.c. Thus, we should remove
the code which decides whether or not to send the NAND_CMD_READ0 command.
Instead, we unconditionally send the command.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND layer always has NAND_NO_AUTOINCR set, so we will never utilize the
AUTOINCR code in nandsim. We will be removing the NAND_NO_AUTOINCR option soon,
and so kill this code as well.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The drivers' _read() method, absent an error, returns a non-negative integer
indicating the maximum number of bit errors that were corrected in any one
region comprising an ecc step. MTD returns -EUCLEAN if this is >=
bitflip_threshold, 0 otherwise. If bitflip_threshold is zero, the comparison is
not made since these devices lack ECC and always return zero in the non-error
case (thanks Brian)¹. Note that this is a subtle change to the driver
interface.
This and the preceding patches in this set were tested with ubi on top of the
nandsim and docg4 devices, running the ubi test io_basic from mtd-utils.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040468.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds sanity checks that ensure that drivers for controllers with
hardware ECC set the 'strength' element in struct nand_ecc_ctrl. Also stylistic
changes to the line that calculates strength for software ECC.
This v2 simplifies the check. Thanks Brian!¹
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040890.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ecc.read_page() method for nand drivers is changed to return the maximum
number of bitflips that were corrected on any one region covering an ecc step,
This patch doesn't change what the nand code returns to mtd.
This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040883.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by (freescale changes): Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
An element 'bitflip_threshold' is added to struct mtd_info, and also exposed as
a read/write variable in sysfs. This will be used to determine whether or not
mtd_read() returns -EUCLEAN or 0 (absent a hard error). If the driver leaves it
as zero, mtd will set it to a default value of ecc_strength.
This v2 adds the line that propagates bitflip_threshold from the master to the
partitions - thanks Ivan¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040900.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ecc_strength element of struct mtd_info is exposed as a read-only variable in
sysfs.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes a couple of ecc strength values for which I earlier made conservative
guesses, but whose correct values were later determined¹ (thanks Ivan). Also
sets strength for fsl_ifc_nand, which was merged to mainline after the original
patch that set the strength for all drivers.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040325.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ecc_strength element of mtd_info will be the strength of one ecc step, not of
the entire writesize, as was previously planned. This is the appropriate way
because, as was pointed out¹, bit errors in excess of the strength of one
step can cause a hard error if they all occur within the same ecc region.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040313.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
To make sure the NAND chip is properly programmed we need a status
command before each page write. When CONFIG_MTD_NAND_VERIFY_WRITE=y this
assumption is broken when writing multiple pages consecutively. This
patch fixes this.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is tested on i.MX27.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
