Render standy allows the GPU to power down the render unit when idle.
In order for this to work, it needs a page of graphics memory to save
state. This patch allocates that page and enables the feature on
supported chipsets.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This brings some hardware workaround for HDMI port on PCH (Ibex Peak),
which fixes unstable issues like during rotation.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the ideal error range can't be reached, this will safely use
a most closed one. Clean up some dumb codes in DPLL function too.
This fixes DPLL clock issue against one monitor at 1680x1050@60hz.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Miles Lane reported the following error:
2 locks held by cat/4179:
#0: (&p->lock){+.+.+.}, at: [<c10a3884>] seq_read+0x25/0x315
#1: (&dev_priv->mm.active_list_lock){+.+...}, at: [<c119a854>]
i915_batchbuffer_info+0x2b/0x124
Pid: 4179, comm: cat Not tainted 2.6.32-rc5-git1 #2
Call Trace:
[<c104874f>] ? __debug_show_held_locks+0x1e/0x20
[<c1023fb0>] __might_sleep+0xf0/0xf7
[<c101c393>] kmap+0x17/0x58
[<c119a8d6>] i915_batchbuffer_info+0xad/0x124
[<c10a39bf>] seq_read+0x160/0x315
[<c108fb8c>] ? rw_verify_area+0x98/0xbb
[<c10a385f>] ? seq_read+0x0/0x315
[<c1090331>] vfs_read+0x75/0xa9
[<c10903f9>] sys_read+0x3b/0x5d
[<c1002a8f>] sysenter_do_call+0x12/0x36
The fix is relatively simple, use the atomic variants of kmap() that
avoid the potential sleep.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ironlake suspend/resume support
drm/i915: kill warning in intel_find_pll_g4x_dp
drm/i915: update watermarks before enabling PLLs
drm/i915: add FIFO watermark support for G4x
drm/i915: quiet DP i2c init
drm/i915: fix panel fitting filter coefficient select for Ironlake
drm/i915: fix to setup display reference clock control on Ironlake
drm/i915: Install a fence register for fbc on g4x
drm/i915: save/restore BLC histogram control reg across suspend/resume
drm/i915: Fix FDI M/N setting according with correct color depth
drm/i915: disable powersave feature for Ironlake currently
drm/i915: Fix render reclock availability detection.
drm/i915: Save and restore the GM45 FBC regs on suspend and resume.
drm/i915: Set the LVDS_BORDER when using LVDS scaling mode
drm/i915: disable FBC for Pineview, fixing a boot hang.
Noticed by Andre on IRC.
Also fix up some minor whitespace issues.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The Lenovo W500 laptop hangs inside an SMI on brightness changes,
I thought it just needed the VGA disable but it turned out to require
slightly more work, setting the MC locations up just like the IGP
chip requirements seems to make it all happy again and I can boot
and play with brightness.
We should probably just do this for all chips and give up the VRAM
at 0x0 idea, it never seems to buy us anything but pain.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Once kms is enabled we don't need these, and it causes a problem
with the Lenovo W500 ACPI brightness implementation, it hangs
in a loop inside an SMI.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Immediate readback seems faulty on some chips. I
suspect it takes a while to get through the fifo
to the actual register backbone. There's no need
to read it back, so, just write the driver's copy
of the register's value directly.
Should fix bug 24535 and possibly 24218
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we are evicting from VRAM->RAM we allocate the ttm object,
but we don't set the caching policy on it before blitting into it.
This means on AGP we end up blitting into cached pages, and
the CPU later flushes out on top of them. This was mostly seen as
font corruption.
The other question is why we don't evict VRAM->GTT in a lot of cases,
this would save us some cache transitions since a lot of objects
that are evicted from VRAM will probably end up being pulled back in
a few operations later, and evicting them to system memory involves
2 unnecessary cache transitions.
Signed-off-by: Dave Airlie <airlied@redhat.com>
In commit c1c7af6089 ("drm/i915: force
mode set at lid open time") the intel graphics driver was taught to
restore the LVDS mode on lid open.
That caused problems with interaction with the suspend/resume code,
which commonly runs at the same time (suspend is often caused by the lid
close event, while lid open is commonly a resume event), which was
worked around with in commit 06891e27a9
("drm/i915: fix suspend/resume breakage in lid notifier").
However, in the meantime the lid event code had also grown a user event
notifier (commit 06324194ee: "drm/i915:
generate a KMS uevent at lid open/close time"), and now _that_ causes
problems with suspend/resume and some versions of Xorg reacting to those
uevents by setting the mode.
So this effectively reverts that commit 06324194ee, and makes the lid
open protection logic against suspend/resume more explicit. This fixes
at least one laptop. See
http://bugzilla.kernel.org/show_bug.cgi?id=14484
for more details.
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: Riccardo Magliocchetti <riccardo.magliocchetti@gmail.com>
Cc: Eric Anholt <eric@anholt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes suspend/resume on my rc410 motherboard, it restores
the memory controller setup before posting the GPU, since it seems
to need the MC_FB_LOCATION setup correctly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make sure we have an LVDS encoder before casting enc_priv.
[airlied: also fix two missing cpu_to_le16 casts we noticed on irc]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Make the struct card_info, which is a per struct radeon_device dataset, a
struct member of the radeon device instead of a static per kernel module
value. This should avoid potential problems with two radeon cards installed in
one system.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DVO in 12 bit mode (which seems to be the most common
config) requires 2x ppll.
Fixes fdo bug 21857.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Limiting the pll output range is a good thing generally as
it limits the number of possible pll combinations for a given
frequency presumably to the ones that work best on each card.
That's why the limits are in the bios tables. However, certain
duallink DVI monitors seem to like pll combinations that would
be limited by this at least on pre-DCE 3.0 r6xx hardware. This
might need to be adjusted per family or per clock range in the
future.
See fdo bug 24727.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This sets the fbcon to use TRUECOLOR by default, it then
only modifies the pseudo palette for fbcon, and only touches
the real palette when in 8-bit pseudo color mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes we will get the incorrect display modeline when parsing the detailed
timing in EDID. For example:
>hsync/vsync width is zero
>sync is beyond the blank.
So add the basic check for the detailed timing in EDID to avoid the incorrect
display modeline.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Since we register all radeon devices, and the arbiter only cares about
VGA class ones, we will fail to startup on display controller class devices.
We don't gain anything by using the return value here.
this helps kms on sparc64 get started.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds a new flag to the drmWaitVblank ioctl, which asks the drm
to return immediately and notify userspace when the specified vblank sequence
happens by sending an event back on the drm fd.
The event mechanism works with the other flags supported by the ioctls,
specifically, the vblank sequence can be specified relatively or absolutely,
and works for primary and seconday crtc.
The signal field of the vblank request is used to provide user data,
which will be sent back to user space in the vblank event.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix the main loop to search all buffers before sleeping.
Remove dead code
Signed-off-by: Robert Noland <rnoland@2hip.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Spread spectrum is a periodic disturbance added
to the feedback divider to change the pixel clock
periodically to reduce interference.
Only enabled on LVDS.
v2: add support for r4xx and fix DCE 3
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The *_HIGH regs are reversed. The secondary ones are in the
primary block and vice versa.
We currently only use a 32 bit internal address, so these are
0 for now.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch only changes this is the swap path, where it doesn't loop.
Signed-off-by: Robert Noland <rnoland@2hip.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Reduce the chance of error and avoid a bit of overhead.
- Use switch to assign color and format
Signed-off-by: Robert Noland <rnoland@2hip.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Where supported use ulMinPixelClockPLL_Output rather than
usMinPixelClockPLL_Output for pll_out_min. This seems to
improve pll selection on some boards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problem boils down to the order when the bit11
of the texture size is or'ed to the original width.
In the end each mipmap level has the same width or
height because of that 11 bit is ored to the scaled
down lod with and thus blows up the size again to the
full size or more due to the power of two rounding
afterwards.
The attached patch changes this order so that the
texture sizes are computed correct. Also the on error
the yet missing inputs to the size computation are
printed which helped me to find out where it really breaks.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This sets the fbcon to use TRUECOLOR by default, it then
only modifies the pseudo palette for fbcon, and only touches
the real palette when in 8-bit pseudo color mode.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds registers save/restore for Ironlake to make suspend work.
Signed-off-by: Guo, Chaohong <chaohong.guo@intel.com>
[zhenyuw: some code re-orgnization, and add more save/restore for
FDI link and transcoder registers, also fix palette register for Ironlake]
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When coming back from DPMS or turning on a display, make sure we have
the watermarks set up before turning on the display plane, otherwise we
may get underruns.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Turns out G4x needs to have sensible watermarks set, especially for
self-refresh enabled modes. Add support for it.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Dirk Hohndel <hohndel@infradead.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Must set filter selection as hardcoded coefficients for medium 3x3
filtering, which matches vbios setting for Ironlake.
This fixes display corrupt issue on HP arrandale with new vbios.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For new stepping of PCH, the display reference clock
is fully under driver's control. This one trys to setup
all needed reference clock for different outputs. Older
stepping of PCH chipset should be ignoring this.
This fixes output failure issue on newer PCH which requires
driver to take control of reference clock enabling.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Original radeon didn't have a connector table in the
bios. Check for the CRT table and if we have one,
add a VGA connector.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Need to check the return type for the quirk function
to decide whether we add the connectors and encoders.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Sometimes we will get the incorrect display modeline when parsing the detailed
timing in EDID. For example:
>hsync/vsync width is zero
>sync is beyond the blank.
So add the basic check for the detailed timing in EDID to avoid the incorrect
display modeline.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
D1MODE_INTERLEAVE_EN was getting set in some cases
in the encoder quirks function due to the changes in
5a9bcacc0a
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based partly on a patch from
Christian Koenig <deathsimple@vodafone.de>
- fix several memory leaks in radeon_connector->edid handling
- store edid in radeon_connector->edid in detect() or get_modes()
- switch hdmi detect code to use radeon_connector->edid
- add support for oem boards multiple connectors that share
a ddc line.
- short circuit lvds_detect() if have a stored edid
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To enable framebuffer compression on a g4x, we not only need the buffer
to tiled (X only), we also need to hold a fence register for the buffer.
Currently we only install a fence register for pre-i965s when setting up
the scanout buffer. Rather than adding some convoluted logic to
g4x_enable_fbc() to acquire a fence register, and perhaps to
g4x_disable_fbc() to release it again, we can extend the acquisition
during setup to all chipsets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Turns out some machines, like the ThinkPad X40 don't come back if you
don't save/restore this register.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
- crtc 0 routing was wrong
- need to clear various timing bits in FP_GEN_CNTL
- need to set FP_H/V2_SYNC_STRT_WID regs for crtc 1
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_encoder->active_device defines the active routing
between the encoder and connector. The encoder fixup and
dpms functions need to know the active_device to function
properly. Setting active_device in the prepare hook was
too late in some cases.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
FDI M/N calculation hasn't taken the current pipe color depth into account,
but always set as 24bpp. This one checks current pipe color depth setting,
and change FDI M/N calculation a little to use bits_per_pixel first, then
convert to bytes_per_pixel later.
This fixes display corrupt issue on Arrandle LVDS with 1600x900 panel
in 18bpp dual-channel mode.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Until we figure out the right setting for powersave features on
Ironlake, disable it for now. Also disable watermark update,
which has new registers for it on Ironlake too.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: Resolved against the Pineview FBC changes]
Signed-off-by: Eric Anholt <eric@anholt.net>
If the device didn't support EDP, we would bail out too soon.
Signed-off-by: Andy Lutomirski <luto@mit.edu>
[anholt: Pulled this patch out of the patch for adding quirks to
enable reclocking.]
Signed-off-by: Eric Anholt <eric@anholt.net>
This hasn't fixed the regressions we were testing against, but clearly
should be required.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
According to the spec the LVDS_BORDER_ENABLE bit decides whether the border
data should be included in the active display and data sent to the panel.
Border should be used when in VGA centered (un-scaled) mode or when scaling
a 4:3 source image to a wide screen panel (typical 16:9).
So when the LVDS scaling is used, decide whether the LVDS_BORDER should be
enabled or not according to the current scaling mode.
At the same time fix the typo error in LVDS center scaling mode.
https://bugs.freedesktop.org/show_bug.cgi?id=23789
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
tested-by: Zhao Jian <jian.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Pineview doesn't have this FBC mechanism, so this code doesn't apply.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
drm modes are objects with indentifiers. Make sure to preserve
the mode id when copying mode params.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In case the system has bad native mode info but
valid edid.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This reduces the number of mode format conversions needed
and makes native panel mode support cleaner.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- clean up tv timing handling
- unify SetCRTC_Timing and SetCRTC_UsingDTDTiming
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
DCE3+ has an AdjustDisplayPll that will adjust the pixel
clock accordingly based on the encoder/transmitter to
handle special hw requirements.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the panel data is bogus this can lead to problems
later when the hardware trys to set the mode. If the
data is invalid, report LVDS as disconnected.
Should fix fdo bug 24247.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While investigating the cause of CRTC FIFO underruns, I noticed that when
converting the memory bandwidth calculation from the userspace X driver code,
an instance of '8.0' was apparently accidentally converted to '80'.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The hook may change the number of bytes per pixel being scanned out, which
affects the CRTC memory bandwidth requirements. E.g. booting in 8bpp and then
running X in 32bpp would result in the bandwidth requirements being
underestimated for the latter and consequently in CRTC FIFO underruns causing
visible artifacts with 3D intensive workloads.
ATOM changes only compile-tested.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Initialize HDMI outputs as HDMI connectors, not DVI.
drm/i915: Multiply the refresh by 1000 in TV mode validatiion
drm/i915: Enable irq to trace batch buffer completion.
drm/i915: batch submit seqno off-by-one.
drm/i915: Record device minor rather than pointer in TRACE_EVENT
drm/i915: Don't call intel_update_fbc from intel_crtc_cursor_set
conflict in radeon since new init path merged with vga arb code.
Conflicts:
drivers/gpu/drm/radeon/radeon.h
drivers/gpu/drm/radeon/radeon_asic.h
drivers/gpu/drm/radeon/radeon_device.c
There is no need to assign vb before you know that space is available.
[agd5f: adapted for kernel tree.]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
For AGP to work unmapped access must cover VRAM & AGP as
AGP is treated like VRAM by the GPU (ie physical address).
This patch properly setup the virtual memory system aperture
to cover AGP if AGP is enabled. It seems that there is memory
corruption after resume when using AGP (RV770 seems unaffected
thought). Version 2 just fix merge issue with updated AGP
fallback patch.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When GPU acceleration is not working with AGP try to fallback to non
AGP GART (either PCI or PCIE GART). This should make KMS failure on
AGP less painfull. We still need to find out what is wrong when AGP
fails but at least user have a lot of more chances to get a working
configuration with acceleration. This patch also cleanup R600/RV770
fallback path so they use same code as others asics. Version 2
factorize agp disabling logic to avoid code duplication and bugs.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Bad generated header file leaded to use wrong register
to check IRQ status and acknowledge them. Fix the header
and use proper registers.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
the global refcount wasn't being increased after the first reference.
this caused an oops on unload on a multi-gpu card.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.
this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.
Tested on r100/r600/i945.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also add single crtc for RN50 chips.
changes in v2:
fix vblank init to respect single crtc flag
fix r100 mode bandwidth to respect single crtc flag
Signed-off-by: Dave Airlie <airlied@redhat.com>
We can get the corresponding info by adding the boot option of "drm.debug=
0x07". But On some boxes it will print the following message many times in
course of moving mouse. In such case the useful DRM debug info will be flushed.
>[drm:drm_mode_cursor_ioctl],
Avoid using the DRM_DEBUG_KMS in drm_mode_cursor_ioctl.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
"Surround View" is an option in the system bios that
enables the AMD IGP chip in conjunction with a
discrete AMD card. However, since the IGP vbios is
part of the system bios it is not accessible via the
rom bar or the legacy vga location. When "Surround View"
is enabled in the system bios, the system bios puts a
copy of the IGP vbios image at the start of vram.
This patch adds support for reading the vbios image out
of vram on IGP cards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Even if the physical output connector is DVI, calling it HDMI
tells the user that there's HDMI audio signaling support.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
As of 559ee21d26 the actual refresh rate
is returned by the function of drm_mode_vrefresh, so multiply the refresh
rate by 1000 in TV mode validation.
At the same time the error is expanded from 10 to 1000.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Avivo hw have vblank interrupt in different place, fixes
irq handling (especialy irq disabling while suspending or
shuting down the module).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
R600 & RV770 family are all using atombios so remove dead code and
print an error message if we fail to find a valid atombios.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When acceleration doesn't work we should free associated memory
and stop GPU block responsible for hardware acceleration so we
don't waste resource or let think one component of the driver that
a GPU feature is working/running while it doesn't actualy work.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We were calling reset unconditionaly in the startup path
this is bad we need to call GPU reset for a good reason
as after reset the GPU is in unknown states. To avoid any
more bad things to happen we now also unconditionaly
reinitialize the GPU after reset. This patch fix few issues
reported by different people regarding KMS & R6XX/RV7XX hw.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This split write back buffer handling into 3 functions,
wb_fini for cleanup, wb_enable/wb_disable for enabling/disabling
write back used for suspend/resume. This should fix
potential issue of letting the write back active before
suspending. We need to allocate memory in wb_enable because
we can only allocate once GART is running.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This remove old init path and allow code cleanup, now all hw
use the new init path, see top of radeon.h for description of
this.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
New init path allow to simply asic initialization and make easier
to trace what happen on each different asic. We are removing most
callback. Do a massive RS600 register cleanup to clarify RS600
register, we are still bit fuzy on some register and waiting for
more informations. I don't have hw to test, so this patch is a
best effort to not break anythings and to try to improve things.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also cleanup register specific to RS690/RS740. Version 2 add
missing header file for register, remove unecessary call to AGP
function and fix an indentation bug.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
New init path allow to simply asic initialization and make easier
to trace what happen on each different asic. We are removing most
callback. More cleanup should happen latter to remove even more
callback. Also cleanup register specific to R100,RV200,RV250.
Version 2 correct the placement on IGP of the VRAM inside GPU address
space to match the stollen RAM placement of IGP.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Also cleanup register specific to RS400/RS480. This patch also fix
legacy VGA register used to disable VGA access we were programming
wrong register. Now we should properly disable VGA on r100 up to
rs400 asics. Note that RS400/RS480 resume is broken, it hangs the
computer while reprogramming dynamic clock, doesn't work either
without that patch. We need to spend more time investigating this
issue. Version 2 of the patch remove dead code that was left
commented out in the previous version. Version 3 correct the
placement on IGP of the VRAM inside GPU address space to match the
stollen RAM placement of IGP.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (25 commits)
drm/radeon/kms: Convert R520 to new init path and associated cleanup
drm/radeon/kms: Convert RV515 to new init path and associated cleanup
drm: fix radeon DRM warnings when !CONFIG_DEBUG_FS
drm: fix drm_fb_helper warning when !CONFIG_MAGIC_SYSRQ
drm/r600: fix memory leak introduced with 64k malloc avoidance fix.
drm/kms: make fb helper work for all drivers.
drm/radeon/r600: fix offset handling in CS parser
drm/radeon/kms/r600: fix forcing pci mode on agp cards
drm/radeon/kms: fix for the extra pages copying.
drm/radeon/kms/r600: add support for vline relocs
drm/radeon/kms: fix some bugs in vline reloc
drm/radeon/kms/r600: clamp vram to aperture size
drm/kms: protect against fb helper not being created.
drm/r600: get values from the passed in IB not the copy.
drm: create gitignore file for radeon
drm/radeon/kms: remove unneeded master create/destroy functions.
drm/kms: start adding command line interface using fb.
fb: change rules for global rules match.
drm/radeon/kms: don't require up to 64k allocations. (v2)
drm/radeon/kms: enable dac load detection by default.
...
Trivial conflicts in drivers/gpu/drm/radeon/radeon_asic.h due to adding
'->vga_set_state' function pointers.
If we trigger a tracepoint for batch buffer submission, it is a reasonable
assumption that we wish to also trace the batch buffer completion. So in
order to capture the completion events, we need to enable irqs... However,
we cannot rely on the completion event to disable the irq later, so we
defer the irq disable to the retire request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
We increment the seqno number between submitting the batch buffer and
the flush/interrupt that demarcates its end, so the tracepoint needs to
reference the incremented value to match the completion event.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Convert the r520 asic support to new init path, change are smaller than
previous one as most of the architecture is now in place and more code
sharing can happen btw various asics.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Convert the rv515 asic support to new init path also add an explanation
in radeon.h about the new init path. There is also few cleanups
associated with this change (others asic calling rv515 helper
functions).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Compiling the radeon DRM driver with !CONFIG_DEBUG_FS
throws the following warnings:
drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_ttm_debugfs_init':
drivers/gpu/drm/radeon/radeon_ttm.c:714: warning: unused variable 'i'
drivers/gpu/drm/radeon/radeon_ttm.c: At top level:
drivers/gpu/drm/radeon/radeon_ttm.c:692: warning: 'radeon_mem_types_list' defined but not used
drivers/gpu/drm/radeon/radeon_ttm.c:693: warning: 'radeon_mem_types_names' defined but not used
Fix: move these variables inside the #if defined(CONFIG_DEBUG_FS)
block in radeon_ttm_debugsfs_init(), which is the only place using them.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Compiling DRM throws the following warning if MAGIC_SYSRQ is disabled:
drivers/gpu/drm/drm_fb_helper.c:101: warning: 'sysrq_drm_fb_helper_restore_op' defined but not used
Fix: place sysrq_drm_fb_helper_restore_op and associated
definitions inside #ifdef CONFIG_MAGIC_SYSRQ.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Commit 74dff282 exposed this unnecessary call by causing a change in
the failure path on i965 where framebuffer compression will be turned
on and off on every cursor update. If you don't have the xf86-video-intel
fix to avoid the blinking cursor effect, this is very slow.
Symptoms were a far more noticeable cursor blink with every cursor image
change combined with severe slowdown for animated cursors.
Signed-off-by: Brian Rogers <brian@xyzw.org>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
The legacy r600 path shares code, but doesn't share quite enough
to get the freeing correct. Free the pages here also.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This initialises the fb helper with the connector helper,
so that the fb cmdline code works for intel as well.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Need add reloc offset to the offset in the actual
packet. Fixes use of the DRAW_INDEX packet by the 3D
driver.
[airlied: modified first one where idx_value == ib[idx+0]
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
All we need to do on r6xx/r7xx is clear the RADEON_IS_AGP
flag; the rest is handled in r600.c
fixes fdo bug 23990:
http://bugs.freedesktop.org/show_bug.cgi?id=23990
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Thanks to Michel for pointing this out to me, this is
why I need to get more sleep, over complicate this a bit.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Provides support for anti-tearing functionality
in the ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
- fix offset of NOP packet for parsing
- fix p->idx increments
- fix bad mask when updating crtc vline info
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
r6xx and r7xx was missing this. We don't support
non-CPU accessible vram yet.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
If drivers don't init the fb helper on the connector, the cmdline
code won't work, but it shouldn't crash either.
Signed-off-by: Dave Airlie <airlied@redhat.com>
this avoids reading back the IB on AGP, also it avoids
the race where since we haven't fetched the page from the main IB
and written it to the gpu one, reading back fetches 0.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Got lots of untracked files after compiling.
These files are generated, thus should be ignored by git.
Signed-off-by: WANG Cong <amwang@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
[note this requires an fb patch posted to linux-fbdev-devel already]
This uses the normal video= command line option to control the kms
output setup at boot time. It is used to override the autodetection
done by kms.
video= normally takes a framebuffer as the first parameter, in kms
it will take a connector name, DVI-I-1, or LVDS-1 etc. If no output
connector is specified the mode string will apply to all connectors.
The mode specification used will match down the probed modes, and if
no mode is found it will add a CVT mode that matches.
video=1024x768 - all connectors match a 1024x768 mode or add a CVT on
video=VGA-1:1024x768, VGA-1 connector gets mode only.
The same strings as used in current fb modedb.c are used, except I've
added three more letters, e, D, d, e = enable, D = enable Digital,
d = disable, which allow a connector to be forced into a certain state.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This avoids needing to do a kmalloc > PAGE_SIZE for the main
indirect buffer chunk, it adds an accessor for all reads from
the chunk and caches a single page at a time for subsequent
reads.
changes since v1:
Use a two page pool which should be the most common case
a single packet spanning > PAGE_SIZE will be hit, but I'm
having trouble seeing anywhere we currently generate anything like that.
hopefully proper short page copying at end
added parser_error flag to set deep errors instead of having to test
every ib value fetch.
fixed bug in patch that went to list.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (57 commits)
drm/i915: Handle ERESTARTSYS during page fault
drm/i915: Warn before mmaping a purgeable buffer.
drm/i915: Track purged state.
drm/i915: Remove eviction debug spam
drm/i915: Immediately discard any backing storage for uneeded objects
drm/i915: Do not mis-classify clean objects as purgeable
drm/i915: Whitespace correction for madv
drm/i915: BUG_ON page refleak during unbind
drm/i915: Search harder for a reusable object
drm/i915: Clean up evict from list.
drm/i915: Add tracepoints
drm/i915: framebuffer compression for GM45+
drm/i915: split display functions by chip type
drm/i915: Skip the sanity checks if the current relocation is valid
drm/i915: Check that the relocation points to within the target
drm/i915: correct FBC update when pipe base update occurs
drm/i915: blacklist Acer AspireOne lid status
ACPI: make ACPI button funcs no-ops if not built in
drm/i915: prevent FIFO calculation overflows on 32 bits with high dotclocks
drm/i915: intel_display.c handle latency variable efficiently
...
Fix up trivial conflicts in drivers/gpu/drm/i915/{i915_dma.c|i915_drv.h}
* 'drm-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/r600: set correct pitch for 4 byte copy
drm/radeon: consolidate family flags used in pciids.
During a page fault and rebinding the buffer there exists a window for a
signal to arrive during the i915_wait_request() and trigger a
ERESTARTSYS. This used to be handled by returning SIGBUS and thereby
killing the application. Try 'cairo-perf-trace & cairo-test-suite' and
watch X go boom!
The solution as suggested by H. Peter Anvin is to simply return NOPAGE and
leave the higher layers to spot we did not fill the page and resubmit
the page fault.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: stable@kernel.org
[anholt: Mostly squash it with another commit]
In order to correctly prevent the invalid reuse of a purged buffer, we
need to track such events and warn the user before something bad
happens.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Whilst cleaning up the patches for submission, I mis-classified non-dirty
objects as purgeable. This was causing the backing pages for those
objects to be evicted under memory-pressure, discarding valid and
unreplaceable texture data.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
As evict_something() is called by routines that do not repeatedly search
again, try harder in the initial search to find an object that matches
the request.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
First the routine attempted to unlock a mutex it did not own along the
error path.
Secondly the routine should never be called on any list but the inactive
one, since we attempt to unbind those objects, so fix the calling semantics.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
By adding tracepoint equivalents for WATCH_BUF/EXEC we are able to monitor
the lifetimes of objects, requests and significant events. These events can
then be probed using the tracing frameworks, such as systemtap and, in
particular, perf.
For example to record the stack trace for every GPU stall during a run, use
$ perf record -e i915:i915_gem_request_wait_begin -c 1 -g
And
$ perf report
to view the results.
[Updated to fix compilation issues caused.]
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Ben Gamari <bgamari@gmail.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
Add support for framebuffer compression on GM45 and above. Removes
some unnecessary I915_HAS_FBC checks as well (this is now part of the
FBC display function).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch splits out several of the display functions into a separate
display function table to avoid tons of chipset specific if..else
if..else if blocks all over. There are more opportunities for this
(some noted in the structure defintition); so more cleanup patches will
follow.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (133 commits)
drm/vgaarb: add VGA arbitration support to the drm and kms.
drm/radeon: some r420s have a CP race with the DMA engine.
drm/radeon/r600/kms: rv670 is not DCE3
drm/radeon/kms: r420 idle after programming GA_ENHANCE
drm/radeon/kms: more fixes to rv770 suspend/resume path.
drm/radeon/kms: more alignment for rv770.c with r600.c
drm/radeon/kms: rv770 blit init called too late.
drm/radeon/kms: move around new init path code to avoid posting at init
drm/radeon/r600: fix some issues with suspend/resume.
drm/radeon/kms: disable VGA rendering engine before taking over VRAM
drm/radeon/kms: Move radeon_get_clock_info() call out of radeon_clocks_init().
drm/radeon/kms: add initial connector properties
drm/radeon/kms: Use surfaces for scanout / cursor byte swapping on big endian.
drm/radeon/kms: don't fail if we fail to init GPU acceleration
drm/r600/kms: fixup number of loops per blit calculation.
drm/radeon/kms: reprogram format in set base.
drm/radeon: avivo chips have no separate int bit for display
drm/radeon/r600: don't do interrupts
drm: fix _DRM_GEM addmap error message
drm: update crtc x/y when only fb changes
...
Fixed up trivial conflicts in firmware/Makefile due to network driver
(cxgb3) and drm (mga/r128/radeon) firmware being listed next to each
other.
VGA arb requires DRM support for non-kms drivers, to turn on/off
irqs when disabling the mem/io regions.
VGA arb requires KMS support for GPUs where we can turn off VGA
decoding. Currently we know how to do this for intel and radeon
kms drivers, which allows them to be removed from the arbiter.
This patch comes from Fedora rawhide kernel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch makes sure the CP doesn't DMA do VRAM while 2D
is active by inserting a CP resync token.
todo: port to kms.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This resumes my
RV730PRO (4650)
RV770 (4850)
fine.
Still researching the RV4550 (RV710), resumes without X fine.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows subsytems to provide devtmpfs with non-default permissions
for the device node. Instead of the default mode of 0600, null, zero,
random, urandom, full, tty, ptmx now have a mode of 0666, which allows
non-privileged processes to access standard device nodes in case no
other userspace process applies the expected permissions.
This also fixes a wrong assignment in pktcdvd and a checkpatch.pl complain.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the presumed_offset as feed to userspace and returned to the kernel
from a previous execbuffer is still valid, then we do not need to rewrite
the relocation entry and may skip the offset sanity checks.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Eric noted a potential concern with the low bits not being strictly used
as part of the absolute offset (instead part of the command stream to the
GPU), but in practice that should not be an issue.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Andy Whitcroft <apw@canonical.com>
Cc: Eric Anholt <eric@anholt.net>
CC: stable@kernel.org
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We really don't want to post the card at init, it takes a relatively
long time and isn't required, so split the resume path into
a startup path called by both init/resume and separate resume
entry point to do posting.
Signed-off-by: Dave Airlie <airlied@redhat.com>
a) don't zero gart table on gart enable
b) move pinning shader object into resume path
c) unpin shader object on suspend
d) set cp ready to false after cp shutdown on suspend.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Before we use any of VRAM, we need to disable the VGA rendering
engine, this render text mode into a graphical framebuffer
for scanout, however it does this on vblank, and can end up
overwriting the GART table and r600 shader objects.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Someone on IRC reported problems after commit
95a8f1bf4f ('drm/radeon/kms: Move
radeon_clocks_init() call back after getting VRAM info.'). And indeed, at least
some ASIC vram_info hooks use the clock info obtained by
radeon_get_clock_info(). So, move that call out of radeon_clocks_init(), ahead
of the radeon_vram_info() call.
[airlied - fixup missing r600/rv770 calls]
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
drm/radeon/kms: fix get clock info calls for r600/rv770 init path.
These were missed when it got split out.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds:
coherent mode: TMDS coherent mode for atom cards.
scaling mode: LVDS scaler mode
load detect: DAC load detection, DVI-I, VGA, TV
tmds pll: legacy TMDS pll selection
tv standard: TV standard selection.
for later: other TV ones? dvi subconnector selection using std prop
[contains fixes pointed out on dri-devel for atom bios mixups
by Michel]
Signed-off-by: Dave Airlie <airlied@redhat.com>
Userspace can query if acceleration is working or not true get
info ioctl and could fallback to software if for some reason
kernel failed to initialize KMS. This should allow to give a
working KMS setup in all case (even with non functionning accel).
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some people were seeing
*ERROR* radeon: writting more dword to ring than expected
after certain blits, the loops calculation didn't take
into account that we do a separate blit for the remainder
after doing the aligned blits.
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should in theory fix the problem with a mode set being required
for adjusting the color depth.
This also adds in the necessary bits to the format tables for
8-bit, though it doesn't work yet.
Signed-off-by: Dave Airlie <airlied@redhat.com>
display interrupts are not enabled via this register, the
DISPLAY_INT bit is a status only to show that other regs
need to be read.
Noticed by Alex Deucher
Signed-off-by: Dave Airlie <airlied@redhat.com>
Interrupts are not supported yet. This prevents
things like mesa from trying to use them.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix the error message: this is add, not rm.
Move the closing brace to proper spot: _DRM_GEM branch should not be
included in the block.
Signed-off-by: Pekka Paalanen <pq@iki.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The drm_fb_helper shouldn't mess with CRTCs that aren't enabled or in
its initial config. Ideally it shouldn't even include CRTCs in its
initial config if they're not in use, but my old fix for that no longer
works. At any rate, this fixes a real bug I was seeing where after a
console blank, both pipes would come back on, even though only one had
been enabled before that. Since the other pipe had a bogus config,
this led to some screen corruption.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We usually don't have an SAREA, and we always want to update the FBC
status anyway, so move the update up above the various master/sarea
checks.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It reports closed when open, leading to "no outputs found" at startup
unless a VGA cable is plugged in.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
A very high dotclock (e.g. 229500kHz as reported by Anton) can cause
the entries_required variable to overflow, potentially leading to a
FIFO watermark value that's too low to support the given mode. Split
the division across the calculation to avoid this.
Cc: stable@kernel.org
Reported-by: Anton Khirnov <wyskas@gmail.com>
Tested-by: Anton Khirnov <wyskas@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
By handling latency variable efficiently we also get rid of this warning :
CC [M] drivers/gpu/drm/i915/intel_display.o
drivers/gpu/drm/i915/intel_display.c: In function ‘igd_enable_cxsr’:
drivers/gpu/drm/i915/intel_display.c:1918: warning: ‘latency’ may be used uninitialized in this function
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Don't need extra config restore like for intel_agp, which
might cause resume hang issue found by Alan on 845G.
Cc: Stable Team <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Due to the necessity of having to take the struct_mutex, the i915
shrinker can not free the inactive lists if we fail to allocate memory
whilst processing a batch buffer, triggering an OOM and an ENOMEM that
is reported back to userspace. In order to fare better under such
circumstances we need to manually retry a failed allocation after
evicting inactive buffers.
To do so involves 3 steps:
1. Marking the backing shm pages as NORETRY.
2. Updating the get_pages() callers to evict something on failure and then
retry.
3. Revamping the evict something logic to be smarter about the required
buffer size and prefer to use volatile or clean inactive pages.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Similar to the madvise() concept, the application may wish to mark some
data as volatile. That is in the event of memory pressure the kernel is
free to discard such buffers safe in the knowledge that the application
can recreate them on demand, and is simply using these as a cache.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This should help GEM handle memory pressure sitatuions more gracefully.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is no need to store the gtt_alignment as it is either explicitly
set according to the hardware requirements (e.g. scanout) or the
minimum alignment is computed on demand.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If we failed to set the domain, the buffer was no longer being tracked
on any list.
Cc: stable@kernel.org
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Due to a bogus FBC support check and failing to check for FBC support
in the right places, mode setting on non-mobile platforms could fail
and hang in the FBC disable routine. Fix it up.
This fix highlights the need for cleanups in this area (function
pointers and better feature support checks). Patches for that to
follow.
Tested-by: Kenny Graunke <kenny@whitecape.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We now unconditionally restore the mode at lid open time since some
platforms turn off the panel, pipes or other display elements when the
lid is closed. There's a problem with doing this at resume time
however.
At resume time, we'll get a lid event, but restoring the mode at that
time may not be safe (e.g. if we get the lid event before global state
has been restored), so check the suspended state and make sure our
restore is locked against other mode updates.
Tested-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is a very real possibility that multiple CPUs will notice that the
GPU is wedged. This introduces all sorts of potential race conditions.
Make the wedged flag atomic to mitigate this risk.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch uses the previously introduced chip reset logic to reset the
chip when an error event is detected.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This patch puts in place the machinery to attempt to reset the GPU. This
will be used when attempting to recover from a GPU hang.
Signed-off-by: Owain G. Ainsworth <oga@openbsd.org>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We set a periodic timer to check on the GPU, resetting it every time a
batch is completed. If the timer elapses, we check acthd. If acthd
hasn't changed in two timer periods, we assume the chip is wedged.
This is implemented in such a way that it leaves the option open to
employ adaptive timer intervals in the future. One could wait until
several timer periods have elapsed before declaring the chip dead. If
the chip comes back after several periods but before the "dead"
threshold, the timer interval or dead threshold could be raised.
It is important to note that while checking for active requests, we need
to account for the fact that requests are removed from the list (i.e.
retired) in a deferred work queue handler. This means that merely
checking for an empty request_list is insufficient; the list could be
non-empty yet the GPU still idle, causing the hangcheck timer to
incorrectly mark the GPU as wedged (it took me a while to figure that
out---sigh...)
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We'll need it in i915_irq.c for checking whether there are outstanding
requests. Also, the function really ought to return a bool, not an int.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We move the display-specific code into it's own functions, called
from the general GPU state save/restore functions. This will be needed
later by the GPU reset code.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
i915_wait_request() only checks mm.wedged after it interacts with the
hardware, generally causing the driver to lock up waiting for a wedged
chip. Make sure we check mm.wedged as the first thing we do.
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
BLC_PWM_CTL2 is for 965+ only, so add device model check for
legacy backlight control.
For native backlight control, it maps the backlight value (0~255)
in opregion ASLE[BCLP] to backlight duty cycle (0~max_backlight)
and set into control register.
It also add support for IGD device, which follows opregion spec.
Signed-off-by: Li Peng <peng.li@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Arrandale has new window based method for panel fitting.
This one enables full screen aspect scaling on LVDS. It fixes
standard mode display failure on LVDS for Arrandale.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
This is not required on newer stepping hardware to get
reliable force detect status. Removing this fixes screen
blank flicker in CRT detect on IGDNG.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
IGDNG LVDS SSC uses 120Mhz freq. This fixes one
1600x900 LVDS panel black issue on IGDNG with SSC enabled.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
New register for PCH LVDS on IGDNG should be used.
This is a copy-n-paste typo. This fixes possible dual
channel LVDS panel failure on IGDNG.
Cc: Stable Team <stable@kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fixes RMX problems on older Apple laptops which don't have an x86 BIOS ROM.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We sometimes lock IB then the ring and sometimes the ring then
the IB. This is mostly due to the IB locking not being well defined
about what data in the structs it actually locks. Define what I
believe is the correct behaviour and gets rid of the lock dep ordering
warning.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fixes leak hidden in commit 9f022ddfb2
('drm/radeon/kms: convert r4xx to new init path').
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
It may indirectly call radeon_set_clock_gating() which relies on the VRAM info.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Although the new radeon driver ioctls don't need this, some of
the drm initialisation ioctls require it, so add this to make them
work.
Signed-off-by: Dave Airlie <airlied@redhat.com>
GART static one time initialization was mixed up with GART
enabling/disabling which could happen several time for instance
during suspend/resume cycles. This patch splits all GART
handling into 4 differents function. gart_init is for one
time initialization, gart_deinit is called upon module unload
to free resources allocated by gart_init, gart_enable enable
the GART and is intented to be call after first initialization
and at each resume cycle or reset cycle. Finaly gart_disable
stop the GART and is intended to be call at suspend time or
when unloading the module.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
radeon_share.h was begining to give problem with include order in
respect of radeon.h. It's easier and also i think cleaner to move
what was in radeon_share.h into radeon.h. At the same time use the
extern keyword for function shared accross the module.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Move mtrr range and memory information printing to radeon_object_init,
this are memory information and initialization common to all GPU and
they better fit in this function. Will also prevent code duplication
with upcoming init path changes.
airlied: fixed warning introduced
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This convert r4xx to new init path it also fix few bugs.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
rv6xx emits two extra dwords in the render target setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
drm_ht_remove_item() does not handle removing an absent item and the hlist
in particular is incorrectly initialised. The easy remedy is simply skip
calling i915_gem_free_mmap_offset() unless we have actually created the
offset and associated ht entry.
This also fixes the mishandling of a partially constructed offset which
leaves pointers initialized after freeing them along the
i915_gem_create_mmap_offset() error paths.
In particular this should fix the oops found here:
https://bugs.launchpad.net/ubuntu/+source/xserver-xorg-video-intel/+bug/415357/comments/8
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Cc: stable@kernel.org
Ever since we enabled GEM, the pre-9xx chipsets (particularly 865) have had
serious stability issues. Back in May a wbinvd was added to the DRM to
work around much of the problem. Some failure remained -- easily visible
by dragging a window around on an X -retro desktop, or by looking at bugzilla.
The chipset flush was on the right track -- hitting the right amount of
memory, and it appears to be the only way to flush on these chipsets, but the
flush page was mapped uncached. As a result, the writes trying to clear the
writeback cache ended up bypassing the cache, and not flushing anything! The
wbinvd would flush out other writeback data and often cause the data we wanted
to get flushed, but not always. By removing the setting of the page to UC
and instead just clflushing the data we write to try to flush it, we get the
desired behavior with no wbinvd.
This exports clflush_cache_range(), which was laying around and happened to
basically match the code I was otherwise going to copy from the DRM.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Cc: stable@kernel.org
We are splitting GPU & modeset init so that it's easier
to abord only remaining GPU init when somethings fails.
We want to always provide enough funcionalities to get
fbcon and a shadowfb X working. Only acceptable error
during initialization are memory allocation failure or
io mapping failure.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch adds framebuffer compression (good for about ~0.5W power
savings in the best case) support for pre-GM45 chips. GM45+ have a new,
more flexible FBC scheme that will be added in a separate patch.
FBC can't always be enabled: the compressed buffer must be physically
contiguous and reside in stolen space. So if you have a large display
and a small amount of stolen memory, you may not be able to take
advantage of FBC. In some cases, a BIOS setting controls how much
stolen space is available. Increasing this to 8 or 16M can help.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
R3XX/R4XX AGP asic use the old PCI GART block, not the new PCIE GART.
Make sure we pick the right GART when disabling AGP.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Acked-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With all the other lid pieces in place, it's easy to generate a uevent
for the LVDS connector just like we do for other outputs. Should make
lid open/close fit in with the rest of a userland based output
reconfiguration scheme.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
We can't load or hotplug detect LVDS like we can other outputs, but if
there's a lid device present we can use it as a proxy. This allows the
LFP state to be determined at ->detect time, making configurations
requiring manual intervention today "just work" assuming the lid device
status is correct.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some laptop platforms will disable pipes and/or planes at lid close time
and not restore them when the lid is opened again. So catch the lid
event, and if the lid was opened, force a mode restore.
Fixes fdo bug #21230.
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the output device is LVDS, maybe the pixel clock of adjusted_mode will be
less than that in mode. In such case it will set the incorrect multipler factor
in DPLL_MD register.
So the dpll_md_reg will be reset when the output type is non-SDVO
https://bugs.freedesktop.org/show_bug.cgi?id=22761
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Reviewd-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the sdvo device is detected as SDVO-LVDS, we will check whether the
brightness is supported by issue SDVO enhancement command.
If it is supported, we will add the brightness property and then brightness
can be adjusted.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
When the sdvo device is detected as SDVO-TV, we will check whether the
sepecific picture enhancement is supported. If it is supported, we will
add the corresponnding property for SDVO-TV. We will add the following
property for the SDVO-TV enhancements if they are supported:
* Contrast/Brightness/Saturation/Hue.
* left/right/top/bottom margin: This is implemented by using the
horizontal/vertical overscan enhancements. When the overscan
enhancements are supported, the above properties will be added. This is
to be compatible with what we have done in integrated-TV.
* horizontal pos/vertical pos.
http://bugs.freedesktop.org/show_bug.cgi?id=22891
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
select the correct max number of bytes per blit based
on whether the size is multiple of 4 bytes. This
determines whether we can use 8 or 32 bit pixels for
the blit.
airlied: also merged the IB padding patch +
correcting the VS offset for context
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If module is being unloaded we should not try to handle irq especialy
we should not call into drm helper or we could hard hang the computer
free_irq will call the irq handler to make sure we behave properly.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Atombios will use the mc register access helper and R4XX hw have a
bigger mc range than R3XX so add R4XX specific mc register access
helper.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we stop CP and that it's still processing thing GPU hang might
happen, this patch wait for CP idle (the wait can timeout) so we
can avoid shutting down CP at bad time. This is especialy usefull
when reseting the GPU as it seems GPU reset fails to properly reset
CP when the CP wasn't stop after being idle.
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
ARRAY_SIZE is number of elements not bytes. Fix
ring counts accordingly, also make a few functions
static.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Fix some warnings reported in linux-next + also cleanup some
comment errors noticed by Pekka Paalanen.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Background:
Graphic devices are accessed through ranges in I/O or memory space. While most
modern devices allow relocation of such ranges, some "Legacy" VGA devices
implemented on PCI will typically have the same "hard-decoded" addresses as
they did on ISA. For more details see "PCI Bus Binding to IEEE Std 1275-1994
Standard for Boot (Initialization Configuration) Firmware Revision 2.1"
Section 7, Legacy Devices.
The Resource Access Control (RAC) module inside the X server currently does
the task of arbitration when more than one legacy device co-exists on the same
machine. But the problem happens when these devices are trying to be accessed
by different userspace clients (e.g. two server in parallel). Their address
assignments conflict. Therefore an arbitration scheme _outside_ of the X
server is needed to control the sharing of these resources. This document
introduces the operation of the VGA arbiter implemented for Linux kernel.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Tiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Otherwise, some other userland writing into its buffer may race to land
writes either after the CPU thinks it's got a coherent view, or after its
GTT entries have been redirected to point at the scratch page. Either
result is unpleasant.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reinette Chatre reports a frozen system (with blinking keyboard LEDs)
when switching from graphics mode to the text console, or when
suspending (which does the same thing). With netconsole, the oops
turned out to be
BUG: unable to handle kernel NULL pointer dereference at 0000000000000084
IP: [<ffffffffa03ecaab>] i915_driver_irq_handler+0x26b/0xd20 [i915]
and it's due to the i915_gem.c code doing drm_irq_uninstall() after
having done i915_gem_idle(). And the i915_gem_idle() path will do
i915_gem_idle() ->
i915_gem_cleanup_ringbuffer() ->
i915_gem_cleanup_hws() ->
dev_priv->hw_status_page = NULL;
but if an i915 interrupt comes in after this stage, it may want to
access that hw_status_page, and gets the above NULL pointer dereference.
And since the NULL pointer dereference happens from within an interrupt,
and with the screen still in graphics mode, the common end result is
simply a silently hung machine.
Fix it by simply uninstalling the irq handler before idling rather than
after. Fixes
http://bugzilla.kernel.org/show_bug.cgi?id=13819
Reported-and-tested-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
eDP is exclusive connector too, and add missing crtc_mask
setting for TV.
This fixes
http://bugzilla.kernel.org/show_bug.cgi?id=14139
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Reported-and-tested-by: Carlos R. Mafra <crmafra2@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When an output was disconnected, its mode list would remain. If you later
plugged into a sink with no EDID (projector, etc), you'd inherit the mode
list from the old sink, which is not what you want.
taken from Fedora kernel
Signed-off-by: Dave Airlie <airlied@redhat.com>
The driver gets the bridge device in a number of places, upcoming
vga arb code paths need the bridge device, however they need it in
under a lock, and the pci lookup can allocate memory. So clean
this code up before then and get the bridge once for the driver lifetime.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the r600 KMS + CS support to the Linux kernel.
The r600 TTM support is quite basic and still needs more
work esp around using interrupts, but the polled fencing
should work okay for now.
Also currently TTM is using memcpy to do VRAM moves,
the code is here to use a 3D blit to do this, but
isn't fully debugged yet.
Authors:
Alex Deucher <alexdeucher@gmail.com>
Dave Airlie <airlied@redhat.com>
Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This ports the tv-out code from the DDX to KMS.
adds a radeon.tv module option, radeon.tv=0 to disable tv
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the command stream checker for the RN50, R100 and R200 cards.
It stops any access to 3D registers on RN50, and does checks
on buffer sizes on the r100/r200 cards. It also fixes some texture
sizing checks on r300.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The new code adds modes in the helper, which makes more sense
I disliked the non-driver code adding modes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add the default mode for every output device when there
is no mode for it.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add a function that can be used to add the default mode for the output device
without EDID.
It will add the default mode that meets with the requirements of given
hdisplay/vdisplay limit.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we need to add the standard timing mode, we will firstly check whether it
can be found in DMT table by comparing the hdisplay/vdisplay/vfresh_rate.
If it can't be found, then we will use the cvt/gtf to add the required mode.
If it can be found, it will be returned.
At the same time the function of drm_mode_vrefresh is also fixed. It will
return the result of actual refresh_rate plus 0.5.
For example:
When the calculated value is 84.9, then the fresh_rate is 85.
When the calculated value is 70.02, then the fresh_rate is 70.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
When we add a standard timing mode in UMS, we will first check whether it can
be found in default mode table. If it can't be found, then we will use cvt/gtf
to add the standard timing mode.
Add the default mode table so that we can check whether the given mode
can be found in the default mode table as what we have done in UMS mode.
If the status of one output device is connected but there is no EDID, it will
have no correct mode. In such case we can add some default modes for it. Of
course we only add the modes in the default modes list that visible part is not
greater than 1024x768.
The default mode is autogenerated from the DMT spec. And it is copied from
xserver/hw/xfree86/modes/xf86EdidModes.c. But the mode with reduced blank
feature is removed.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds some rv350+ register for LTE/GTE discard,
and enables the rv515 two sided stencil register.
It also disables the DEPTHXY_OFFSET register which
can be used to workaround the CS checker.
Moves rs690 to proper place in rs600 and uses correct
table on rs600.
Signed-off-by: Dave Airlie <airlied@redhat.com>
According to the docs, the ringbuffer is not allowed to wrap in the middle
of an instruction.
G45 PRM, Vol 1b, p101:
While the “free space” wrap may allow commands to be wrapped around the
end of the Ring Buffer, the wrap should only occur between commands.
Padding (with NOP) may be required to follow this restriction.
Do as commanded.
[Having seen bug reports where there is evidence of split commands, but
apparently the GPU has continued on merrily before a bizarre and untimely
death, this may or may not fix a few random hangs.]
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
CC: Eric Anholt <eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
mac Mini's have a single DDC line on the DVI connector, shared between the
analog link and the digital link. So, if DDC isn't detected on GPIOE (the
usual SDVO DDC link), try GPIOA (the usual VGA DDC link) when there isn't a
VGA monitor connected.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
It seems that on IGDNG the same swizzling setup always applys.
And front buffer tiling needs to set address swizzle in display
arb control too.
Fix plane tricle feed setting in v1 which should be disable bit,
and always setup address swizzle to let hardware care for buffer
tiling in all cases.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
And clean up a small whitespace goof-up in the same function, while
I was looking at it.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
There are several sources of unnecessary power consumption on Intel
graphics systems. The first is the LVDS clock. TFTs don't suffer from
persistence issues like CRTs, and so we can reduce the LVDS refresh rate
when the screen is idle. It will be automatically upclocked when
userspace triggers graphical activity. Beyond that, we can enable memory
self refresh. This allows the memory to go into a lower power state when
the graphics are idle. Finally, we can drop some clocks on the gpu
itself. All of these things can be reenabled between frames when GPU
activity is triggered, and so there should be no user visible graphical
changes.
Signed-off-by: Jesse Barnes <jesse.barnes@intel.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In the event that any one of the DAC analog outputs (R,G,B) were driven
at full-scale (white video) or some analog level close to full-scale
voltage, and if the video cable were then disconnected, the analog video
voltage level would exceed the maximum electrical overstress limit of the
native (thin-oxide) transistors thus causing a long-term reliability concern.
The electrical overstress condition occurs in this particular case.
This patch address the IGD EOS (electrical overstress condition) issue.
When the EOS interrupt occurs, OS should disable DAC and then disable EOS,
then the normal hotplug operation follows.
TODO: it appears the normal unplug interrupt is missed as reported by Li Peng,
need more checks here.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Currently SDVO TV only support NTSC-M format. In this patch
we introduce PAL and SECAM formats available and create seting-format
property at init time. When user dynamically chose preferred
format by xrandr command, it will refine all modelines
provided by SDVO device, then instruct SDVO device to execute.
At the same time the property is added for SDVO-TV so that the SDVO-TV mode can be changed
by using xrandr.
https://bugs.freedesktop.org/show_bug.cgi?id=22891
Signed-off-by: Ma Ling <ling.ma@intel.com>
review-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
For integrated TV there are 3 connector types: S-VIDEO, Composite and
Component(YprPb). Those tv formats whose component flag is true should
be assigned to Component connector, others are for S-VIDEO and Composite.
The patch intends to find appropriate tv format for each connector.
In such case it will return the correct modeline to user space. Otherwise
it will return the incorrect modeline when S-video/composite is connected.
Signed-off-by: Ma Ling <ling.ma@intel.com>
reviewed-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add a debugfs file to dump the entire register range. Here we
assume that reading write-only/reserved registers won't make the chip
angry. Seems to hold true, thankfully.
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Remember to release the local reference if we fail to wait on
the rendering.
(Also whilst in the vicinity add some whitespace so that the phasing of
the operations is clearer.)
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Some i915/i945 platforms have a fairly high memory latency in certain
situations, so increase our constant a bit to avoid FIFO underruns.
The effect should be positive on other platforms as well; we'll have a
bit more insurance against a busy memory subsystem due to the extra
FIFO entries.
Fixes fdo bug #23368. Needed for 2.6.31.
Tested-by: Sven Arvidsson <sa@whiz.se>
Tested-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
For shared tv-out and VGA encoders, we really need to know if
the encoder is just being switched off temporarily in blanking
or if we are really disabling it hard.
Also we need to try harder to disconnect encoders from unused
connectors so we can share more efficently.
(shared encoders stuff is coming in radeon tv-out support)
Signed-off-by: Dave Airlie <airlied@redhat.com>
This produces a warn on for architectures where this gets called
but we don't have a cache flushing implementation suitable.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds code to the drm_mm to talk to debugfs, and adds
support to radeon to add the VRAM and GTT mm lists to debugfs.
I tested with spinlock debugging and it doesn't give out.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Improve CRTDDC mapping by using VBT info
drm/i915: Fix CPU-spinning hangs related to fence usage by using an LRU.
drm/i915: Set crtc/clone mask in different output devices
drm/i915: Always use SDVO_B detect bit for SDVO output detection.
drm/i915: Fix typo that broke SVID1 in intel_sdvo_multifunc_encoder()
drm/i915: Check if BIOS enabled dual-channel LVDS on 8xx, not only on 9xx
drm/i915: Set the multiplier for SDVO on G33 platform
Set accel to none, we really don't want anyone thinking
fb is an accel interface.
Pass pitch not depth to function for intel.
Signed-off-by: Dave Airlie <airlied@redhat.com>
airlied: fixup race against drm info by filling out
tmp before adding it to proc.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Sometimes we can obtain the EDID with multiple blocks from the display device.
For example: HDMI monitor.
When the CEA-EDID block is detected, we should also parse the detailed timing
info from it. Otherwise we will lose some modes for the display device.
The first step is check whether the CEA EDID block is found. If it exists,
it will skip the CEA-data block and parse the detailed timing info.
Signed-off-by: Zhao Yakui <yakui.zhao@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Initially I always meant this code to be shared, but things
ran away from me before I got to it.
This refactors the i915 and radeon kms fbdev interaction layers
out into generic helpers + driver specific pieces.
It moves all the panic/sysrq enhancements to the core file,
and stores a linked list of kernel fbs. This could possibly be
improved to only store the fb which has fbcon on it for panics
etc.
radeon retains some specific codes used for a big endian
workaround.
changes:
fix oops in v1
fix freeing path for crtc_info
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Almost all r128's private ioctls require that the CCE state has
already been initialised. However, most do not test that this has
been done, and will proceed to dereference a null pointer. This may
result in a security vulnerability, since some ioctls are
unprivileged.
This adds a macro for the common initialisation test and changes all
ioctl implementations that require prior initialisation to use that
macro.
Also, r128_do_init_cce() does not test that the CCE state has not
been initialised already. Repeated initialisation may lead to a crash
or resource leak. This adds that test.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Loosely based on a patch by
Jaswinder Singh Rajput <jaswinderlinux@gmail.com>.
KMS support by Dave Airlie <airlied@redhat.com>.
For Radeon 100- to 500-series, firmware blobs look like:
struct {
__be32 datah;
__be32 datal;
} cp_ucode[256];
For Radeon 600-series, there are two separate firmware blobs:
__be32 me_ucode[PM4_UCODE_SIZE * 3];
__be32 pfp_ucode[PFP_UCODE_SIZE];
For Radeon 700-series, likewise:
__be32 me_ucode[R700_PM4_UCODE_SIZE];
__be32 pfp_ucode[R700_PFP_UCODE_SIZE];
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
