This patch adds non-continuous clock mode support
Clock mode on Clock Lane is continuous clock by default.
So if we want to transmit data in non-continuous clock mode
to reduce power consumption, then host driver should set
DSIM_CLKLANE_STOP bit. In this case, host controller turns off
HS clock between high speed transmissions.
For this, this patch adds a new bit, DSIM_CLKLANE_STOP, and makes
the host driver sets this bit only in case that dsi->mode_flags has
MIPI_DSI_CLOCK_NON_CONTINUOUS flag.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
This patch adds a new flag, MIPI_DSI-MODE_LPM, to transmit data
in low power. With this flag, msg.flags has MIPI_DSI_MSG_USE_LPM
so that host driver of each SoC can clear or set relevant register
bit for low power transmission.
All host drivers shall support continuous clock behavior on the
Clock Lane, and optionally may support non-continuous clock behavior.
Both of them can transmit data in high speed of low power.
With each clock behavior, non-continuous or continuous clock mode,
host controller will transmit data in high speed by default so if
peripheral wants to receive data in low power, the peripheral driver
should set MIPI_DSI_MODE_LPM flag.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The type of this function is unsigned long, and it is expected
to return proper fout value or zero if something is wrong.
So this patch fixes wrong return value for error cases.
Signed-off-by: YoungJun Cho <yj44.cho@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Commit "drm/rcar-du: Use struct videomode in platform data" touches board code
in arch/arm/mach-shmobile. There is, to the best of my knowledge, no risk of
conflict for v3.18. Simon, are you fine with getting those changes merged
through Dave's tree (and could you confirm that no conflict should occur) ?
Simon acked the merge:
Acked-by: Simon Horman <horms+renesas@verge.net.au>
* 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev:
drm/rcar-du: Add OF support
drm/rcar-du: Use struct videomode in platform data
video: Add DT bindings for the R-Car Display Unit
video: Add THC63LVDM83D DT bindings documentation
video: Add ADV7123 DT bindings documentation
video: Add DT binding documentation for VGA connector
devicetree: Add vendor prefix "thine" to vendor-prefixes.txt
devicetree: Add vendor prefix "mitsubishi" to vendor-prefixes.txt
drm/shmob: Update copyright notice
drm/rcar-du: Update copyright notice
While zone->name is currently hard coded, the call to kobject_init_and_add()
should follow the more defensive argument list usage (as already done in
other places in ttm_memory.c) where "%s" is used instead of directly passing
in a variable as a format string.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In order to support the "enable GPIO" available in many panel devices,
this commit adds a proper devicetree binding.
By providing an enable GPIO in the devicetree, the driver can now turn
off and on the panel device, and/or the backlight device. Both the
backlight and the GPIO are optional properties.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of setting an initial value for the return code, set it explicitly
on each error path. This is just a cosmetic cleanup, as preparation for the
enable GPIO support.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current backlight support is broken; the driver expects a backlight-class
in the panel devicetree node. Fix this by implementing it properly, getting
an optional backlight from a phandle.
This shouldn't cause any backward-compatibility DT issue because the current
implementation doesn't work and is not even documented.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Using the managed variant to allocate the resource makes the code simpler
and less error-prone.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just a cosmetic cleanup.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Just a trivial cleanup to remove the variable.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit adds the missing calls to of_node_put to release the node
that's currently held by the of_get_child_by_name() call in the panel
info parsing code.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The current error path calls tilcdc_unload() in case of an error to release
the resources. However, this is wrong because not all resources have been
allocated by the time an error occurs in tilcdc_load().
To fix it, this commit adds proper labels to bail out at the different
stages in the load function, and release only the resources actually allocated.
Tested-by: Darren Etheridge <detheridge@ti.com>
Tested-by: Johannes Pointner <johannes.pointner@br-automation.com>
Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- final bits (again) for the rotation support (Sonika Jindal)
- support bl_power in the intel backlight (Jani)
- vdd handling improvements from Ville
- i830M fixes from Ville
- piles of prep work all over to make skl enabling just plug in (Damien, Sonika)
- rename DP training defines to reflect latest edp standards, this touches all
drm drivers supporting DP (Sonika Jindal)
- cache edids during single detect cycle to avoid re-reading it for e.g. audio,
from Chris
- move w/a for registers which are stored in the hw context to the context init
code (Arun&Damien)
- edp panel power sequencer fixes, helps chv a lot (Ville)
- piles of other chv fixes all over
- much more paranoid pageflip handling with stall detection and better recovery
from Chris
- small things all over, as usual
* tag 'drm-intel-next-2014-09-05' of git://anongit.freedesktop.org/drm-intel: (114 commits)
drm/i915: Update DRIVER_DATE to 20140905
drm/i915: Decouple the stuck pageflip on modeset
drm/i915: Check for a stalled page flip after each vblank
drm/i915: Introduce a for_each_plane() macro
drm/i915: Rewrite ABS_DIFF() in a safer manner
drm/i915: Add comments explaining the vdd on/off functions
drm/i915: Move DP port disable to post_disable for pch platforms
drm/i915: Enable DP port earlier
drm/i915: Turn on panel power before doing aux transfers
drm/i915: Be more careful when picking the initial power sequencer pipe
drm/i915: Reset power sequencer pipe tracking when disp2d is off
drm/i915: Track which port is using which pipe's power sequencer
drm/i915: Fix edp vdd locking
drm/i915: Reset the HEAD pointer for the ring after writing START
drm/i915: Fix unsafe vma iteration in i915_drop_caches
drm/i915: init sprites with univeral plane init function
drm/i915: Check of !HAS_PCH_SPLIT() in PCH transcoder funcs
drm/i915: Use HAS_GMCH_DISPLAY un underrun reporting code
drm/i915: Use IS_BROADWELL() instead of IS_GEN8() in forcewake code
drm/i915: Don't call gen8_fbc_sw_flush() on chv
...
Pull in first set of changes from Ben for ast on ppc.
I've done a quick boot test on x86 and it still seems to boot.
* 'drm-next-ast-fixes' of ssh://people.freedesktop.org/~/linux:
drm/ast: Cleanup analog init code path
drm/ast: Don't assume DVO enabled means SIL164 on uninitialized chips
drm/ast: Properly initialize P2A base before using it in ast_init_3rdtx()
drm/ast: POST chip at probe time if VGA not enabled
drm/ast: Try to use MMIO registers when PIO isn't supported
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJUFjfVAAoJEHm+PkMAQRiGANkIAIU3PNrAz9dIItq8a/rEAhnx
l2shHoOyEmyNR2apholM3BPUNX50cbsc/HGdi7lZKLkA/ifAj6B9nFD2NzVsIChD
1QWVcvdkKlVuxXCDd26qbijlfmbTOAWrLw9ntvM+J6ZtECM6zCAZF4MAV/FwogPq
ETGKD76AxJtVIhBMS99troAiC1YxmQ7DKgEr8CraTOR1qwXEonnPCmN/IZA6x2/G
EXiihOuQB5me1X7k4PI0V8CDscQOn+3B2CQHIrjRB+KiTF+iKIuI8n6ORC6bpFh+
U8UZP9wLlIG1BrUHG83pIndglIHotqPcjmtfl1WGrRr2hn7abzVSfV+g5Syo3Vg=
=Ep+s
-----END PGP SIGNATURE-----
drm: backmerge tag 'v3.17-rc5' into drm-next
This is requested to get the fixes for intel and radeon into the
same tree for future development work.
i915_display.c: fix missing dev_priv conflict.
This is the main merge request for Nouveau 3.18, overview:
- various bits of roy's gt21x clock work
- various bits of kepler memory clock work (don't get too excited, there's at least one more major bit left that's busting higher freqs)
- misc fan control improvements
- kepler hdmi infoframe fixes
- dp audio
- l2 cache + cbc improvements
* 'linux-3.18' of git://anongit.freedesktop.org/git/nouveau/linux-2.6: (68 commits)
drm/gt214-/disp: enable dp audio
drm/gt214-/kms: fix hda eld regression
drm/g94-/disp: calculate some dp audio constants
drm/gt214-/kms: perform hda codec setup on displayport too
drm/gk104-/disp: infoframe registers moved yet again on kepler
drm/nouveau/bios: parse older ramcfg/timing data like we do newer ones
drm/nva3/fb/ram: Per-partition regs
drm/nouveau/fb/ram: Support strided regs
drm/nv50/fb/ram: Store the number of partitions in the designated fields
drm/nv50/kms: Set VBLANK time in modeset script
drm/nouveau/bios: Add rammap support for version 1.0
drm/gf100-/pwr/memx: block host and fifo around reclock
drm/nouveau/pwr/memx: fix command ordering around block/unblock
drm/nouveau/pwr/memx: rename fb off/on to block/unblock
drm/nva3/clk: Pause the GPU before reclocking
drm/nouveau/gpio: rename g92 class to g94
drm/gk104-/fb/ram: move fb enable/disable to same place as nvidia
drm/gk104/fb/ram: twiddle some more bits when reclocking
drm/nouveau/bios: parse another large chunk of random memory config data
drm/gk104-/fb/ram: perform certain steps only when bios data differs
...
NVIDIA appear to have tweaked the algorithm from GF110, this implements
the previous algorithm for them still.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Solves blinking on reclocking memory. The value set is an underestimate, but
with non-reduced vblanking this should give us plenty of time
Signed-off-by: Roy Spliet <rspliet@eclipso.eu>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
More accurate as to the function of the opcodes. Not only is FB disabled,
but the host is prevented from touching the GPU. An upcoming patch for
Kepler will also halt PFIFO (as NVIDIA does).
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
nv92 hardware has only 16 interrupt lines, while nv94 and later
has 32. Accessing 0xe0c{0,4} registers on nv92 can lead to incorrect
PDISP setup. This is a regression introduced with
commit 9d0f5ec9ee0fd5dc5fc1cc2cf559286431e406e3
Author: Ben Skeggs <bskeggs@redhat.com>
Date: Mon May 12 15:22:42 2014 +1000
gpio: split g92 class from nv50
Reported-by: estece on #nouveau
Cc: stable@vger.kernel.org # 3.16+
Signed-off-by: Emil Velikov <emil.l.velikov@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
*when* this is done is only a rough approximation of what the binary driver
does.. need to investigate more to see if it matters
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Awful, awful. But, on the GK106 I have, some upcoming patches show
that this is actually necessary after all.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
All the other chipsets should be moved over to this too. It's not needed
yet for the upcoming commits, so left this step as it'll conflict badly
with Roy's GT21x reclocking work.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
NVIDIA binary driver appears to, not sure if it's for a good reason, but
grasping at straws for some GDDR5 reclocking issues here.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
