GT VEBOX DISABLE is only 4 bits wide but it was using a 8 bits wide
mask, the remaning reserved bits is set to 0 causing 4 more
nonexistent VEBOX engines being detected as enabled, triggering the
BUG_ON() because of mismatch between vebox_mask and newly added
VEBOX_MASK().
[ 64.081621] [drm:intel_device_info_init_mmio [i915]] vdbox enable: 0005, instances: 0005
[ 64.081763] [drm:intel_device_info_init_mmio [i915]] vebox enable: 00f1, instances: 0001
[ 64.081825] intel_device_info_init_mmio:925 GEM_BUG_ON(vebox_mask != ({ unsigned int first__ = (VECS0); unsigned int count__ = (2); ((&(dev_priv)->__info)->engine_mask & (((~0UL) - (1UL << (first__)) + 1) & (~0UL >> (64 - 1 - (first__ + count__ - 1))))) >> first__; }))
[ 64.082047] ------------[ cut here ]------------
[ 64.082054] kernel BUG at drivers/gpu/drm/i915/intel_device_info.c:925!
BSpec: 20680
Fixes: 26376a7e74 ("drm/i915/icl: Check for fused-off VDBOX and VEBOX instances")
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20190326230223.26336-1-jose.souza@intel.com
(cherry picked from commit 547fcf9b1c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
meson_drv_unbind() doesn't unregister the IRQ handler, which can lead to
use-after-free if the IRQ fires after unbind:
[ 64.656876] Unable to handle kernel paging request at virtual address ffff000011706dbc
...
[ 64.662001] pc : meson_irq+0x18/0x30 [meson_drm]
I'm assuming that a similar problem could happen on the error path of
bind(), so uninstall the IRQ handler there as well.
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-2-jean-philippe.brucker@arm.com
meson_drv_bind() registers a meson_drm struct as the device's privdata,
but meson_drv_unbind() tries to retrieve a drm_device. This may cause a
segfault on shutdown:
[ 5194.593429] Unable to handle kernel NULL pointer dereference at virtual address 0000000000000197
...
[ 5194.788850] Call trace:
[ 5194.791349] drm_dev_unregister+0x1c/0x118 [drm]
[ 5194.795848] meson_drv_unbind+0x50/0x78 [meson_drm]
Retrieve the right pointer in meson_drv_unbind().
Fixes: bbbe775ec5 ("drm: Add support for Amlogic Meson Graphic Controller")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190322152657.13752-1-jean-philippe.brucker@arm.com
If userspace has open fd(s) when drm_dev_unplug() is run, it will result
in drm_dev_unregister() being called twice. First in drm_dev_unplug() and
then later in drm_release() through the call to drm_put_dev().
Since userspace already holds a ref on drm_device through the drm_minor,
it's not necessary to add extra ref counting based on no open file
handles. Instead just drm_dev_put() unconditionally in drm_dev_unplug().
We now have this:
- Userpace holds a ref on drm_device as long as there's open fd(s)
- The driver holds a ref on drm_device as long as it's bound to the
struct device
When both sides are done with drm_device, it is released.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Reviewed-by: Oleksandr Andrushchenko <oleksandr_andrushchenko@epam.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Sean Paul <sean@poorly.run>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190208140103.28919-2-noralf@tronnes.org
If the downscaling fails and we end up with a best_depth of 0,
then ignore it.
This actually works around a cascade of failure, but it the
simplest fix for now.
The scaling patch broke the udl driver, as the udl driver doesn't
expose planes at all, so gets the two default 32-bit formats, but
the udl driver then ask for 16bpp fbdev, and the scaling code falls
over.
This fixes the udl driver since the scaled depth support was added.
Fixes: f4bd542bca ("drm/fb-helper: Scale back depth to supported maximum")
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190315014621.21816-2-airlied@gmail.com
When CONFIG_IOMMU_API isn't set the following warnings pops up:
drivers/gpu/drm/tegra/vic.c: In function ‘vic_boot’:
drivers/gpu/drm/tegra/vic.c:110:31: error: implicit declaration of function ‘dev_iommu_fwspec_get’; did you mean ‘iommu_fwspec_free’? [-Werror=implicit-function-declaration]
struct iommu_fwspec *spec = dev_iommu_fwspec_get(vic->dev);
^~~~~~~~~~~~~~~~~~~~
iommu_fwspec_free
drivers/gpu/drm/tegra/vic.c:110:31: warning: initialization of ‘struct iommu_fwspec *’ from ‘int’ makes pointer from integer without a cast [-Wint-conversion]
drivers/gpu/drm/tegra/vic.c:117:19: error: ‘struct iommu_fwspec’ has no member named ‘num_ids’
if (spec && spec->num_ids > 0) {
^~
drivers/gpu/drm/tegra/vic.c:118:16: error: ‘struct iommu_fwspec’ has no member named ‘ids’
value = spec->ids[0] & 0xffff;
^~
Rework so that its inside a '#ifdef CONFIG_IOMMU_API' block.
Fixes: f3779cb190 ("drm/tegra: vic: Support stream ID register programming")
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
pm_runtime_get_sync returns negative on failure.
Fixes: eaeb9010bb ("drm/nouveau/debugfs: Wake up GPU before doing any reclocking")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The hmm_devmem_add() function doesn't return NULL, it returns error
pointers.
Fixes: 5be73b6908 ("drm/nouveau/dmem: device memory helpers for SVM")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/nouveau/nouveau_dmem.c: In function 'nouveau_dmem_free':
drivers/gpu/drm/nouveau/nouveau_dmem.c:103:22: warning:
variable 'drm' set but not used [-Wunused-but-set-variable]
struct nouveau_drm *drm;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
[Why]
Black screens or artifacting can occur when enabling FreeSync outside
of the supported range of the monitor. This can happen since the
supported range isn't always the min/max vrefresh range available for
the monitor.
[How]
There was previously a fix that prevented this from happening in the
low range but it didn't cover the upper range. Expand the condition
to include both.
Cc: Sun peng Li <Sunpeng.Li@amd.com>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
MIXER on Exynos5 SoCs uses different synchronisation method than Exynos4
to update internal state (shadow registers).
Apparently the driver implements it incorrectly. The rule should be
as follows:
- do not request updating registers until previous request was finished,
ie. MXR_CFG_LAYER_UPDATE_COUNT must be 0.
- before setting registers synchronisation on VSYNC should be turned off,
ie. MXR_STATUS_SYNC_ENABLE should be reset,
- after finishing MXR_STATUS_SYNC_ENABLE should be set again.
The patch hopefully implements it correctly.
Below sample kernel log from page fault caused by the bug:
[ 25.670038] exynos-sysmmu 14650000.sysmmu: 14450000.mixer: PAGE FAULT occurred at 0x2247b800
[ 25.677888] ------------[ cut here ]------------
[ 25.682164] kernel BUG at ../drivers/iommu/exynos-iommu.c:450!
[ 25.687971] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 25.693778] Modules linked in:
[ 25.696816] CPU: 5 PID: 1553 Comm: fb-release_test Not tainted 5.0.0-rc7-01157-g5f86b1566bdd #136
[ 25.705646] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 25.711710] PC is at exynos_sysmmu_irq+0x1c0/0x264
[ 25.716470] LR is at lock_is_held_type+0x44/0x64
v2: added missing MXR_CFG_LAYER_UPDATE bit setting in mixer_enable_sync
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When calling vmw_fb_set_par(), the mode stored in par->set_mode gets free'd
twice. The first free is in vmw_fb_kms_detach(), the second is near the
end of vmw_fb_set_par() under the name of 'old_mode'. The mode-setting code
only works correctly if the mode doesn't actually change. Removing
'old_mode' in favor of using par->set_mode directly fixes the problem.
Cc: <stable@vger.kernel.org>
Fixes: a278724aa2 ("drm/vmwgfx: Implement fbdev on kms v2")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
If it's not a system error and get_node implementation accommodate the
buffer object then it should return 0 with memm::mm_node set to NULL.
v2: Test for id != -ENOMEM instead of id == -ENOSPC.
Cc: <stable@vger.kernel.org>
Fixes: 4eb085e42f ("drm/vmwgfx: Convert to new IDA API")
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
NV12 framebuffers produced by the VPU shows distorted on RK3288
after win has been disabled when scaling is active.
This issue can be reproduced using a 1080p modeset by:
- Scale a 1280x720 NV12 framebuffer to 1920x1080 on win0
- Disable win0
- Display a 1920x1080 NV12 framebuffer without scaling on win0
- Output will now show the framebuffer distorted
And by:
- Scale a 1280x720 NV12 framebuffer to 1920x1080
- Change to a 720p modeset (win gets disabled and scaling reset to none)
- Output will now show the framebuffer distorted
Fix this by setting scale mode to none when win is disabled.
Fixes: 4c156c21c7 ("drm/rockchip: vop: support plane scale")
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/AM3PR03MB0966DE3E19BACE07328CD637AC7D0@AM3PR03MB0966.eurprd03.prod.outlook.com
When Daniel removed struct_mutex he didn't fix this call to the unlocked
variant which is required since we no longer use struct mutex.
This fixes a bunch of:
WARNING: CPU: 4 PID: 1370 at drivers/gpu/drm/drm_gem.c:931 drm_gem_object_put+0x2b/0x30 [drm]
Modules linked in: udl xt_CHECKSUM ipt_MASQUERADE tun bridge stp llc nf_conntrack_netbios_ns nf_conntrack_broadcast xt_CT ip6t>
CPU: 4 PID: 1370 Comm: Xorg Not tainted 5.0.0+ #2
backtraces when you plug in a udl device.
Fixes: ae358dacd2 (drm/udl: Get rid of dev->struct_mutex usage)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Pull drm fixes and updates from Dave Airlie:
"A few various fixes pulls and one late etnaviv pull but it was nearly
all fixes anyways.
etnaviv:
- late next pull
- mmu mapping fix
- build non-ARM arches
- misc fixes
i915:
- HDCP state handling fix
- shrinker interaction fix
- atomic state leak fix
qxl:
- kick out framebuffers early fix
amdgpu:
- Powerplay fixes
- DC fixes
- BACO turned off for now on vega20
- Locking fix
- KFD MQD fix
- gfx9 golden register updates"
* tag 'drm-next-2019-03-15' of git://anongit.freedesktop.org/drm/drm: (43 commits)
drm/amdgpu: Update gc golden setting for vega family
drm/amd/powerplay: correct power reading on fiji
drm/amd/powerplay: set max fan target temperature as 105C
drm/i915: Relax mmap VMA check
drm/i915: Fix atomic state leak when resetting HDMI link
drm/i915: Acquire breadcrumb ref before cancelling
drm/i915/selftests: Always free spinner on __sseu_prepare error
drm/i915: Reacquire priolist cache after dropping the engine lock
drm/i915: Protect i915_active iterators from the shrinker
drm/i915: HDCP state handling in ddi_update_pipe
drm/qxl: remove conflicting framebuffers earlier
drm/fb-helper: call vga_remove_vgacon automatically.
drm: move i915_kick_out_vgacon to vgaarb
drm/amd/display: don't call dm_pp_ function from an fpu block
drm: add __user attribute to ptr_to_compat()
drm/amdgpu: clear PDs/PTs only after initializing them
drm/amd/display: Pass app_tf by value rather than by reference
Revert "drm/amdgpu: use BACO reset on vega20 if platform support"
drm/amd/powerplay: show the right override pcie parameters
drm/amd/powerplay: honor the OD settings
...
- HDCP state handling in ddi_update_pipe
- Protect i915_active iterators from the shrinker
- Reacquire priolist cache after dropping the engine lock
- (Selftest) Always free spinner on __sseu_prepare error
- Acquire breadcrumb ref before canceling
- Fix atomic state leak on HDMI link reset
- Relax mmap VMA check
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190312205551.GA7701@intel.com
