This patch cleans up the peripheral id table for different ETMv4
implementations.
As per Cortex-A53 TRM, the ETM has following id values:
Peripheral ID0 0x5D 0xFE0
Peripheral ID1 0xB9 0xFE4
Peripheral ID2 0x4B 0xFE8
Peripheral ID3 0x00 0xFEC
where, PID2: has the following format:
[7:4] Revision
[3] JEDEC 0b1 res1. Indicates a JEP106 identity code is used
[2:0] DES_1 0b011 ARM Limited. This is bits[6:4] of JEP106 ID code
The existing table entry checks only the bits [1:0], which is not
sufficient enough. Fix it to match bits [3:0], just like the other
entries do. While at it, correct the comment for A57 and the A53 entry.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At present the ETF or ETR gives out the entire device
buffer, even if there is less or even no trace data
available. This patch limits the trace data given out to
the actual trace data collected.
Cc: mathieu.poirier@linaro.org
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a cleanup patch.
coresight_device->conns holds an array to point to the devices
connected to the OUT ports of a component. Sinks, e.g ETR, do not
have an OUT port (nr_outport = 0), as it streams the trace to
memory via AXI.
At coresight_register() we do :
conns = kcalloc(csdev->nr_outport, sizeof(*conns), GFP_KERNEL);
if (!conns) {
ret = -ENOMEM;
goto err_kzalloc_conns;
}
For ETR, since the total size requested for kcalloc is zero, the return
value is, ZERO_SIZE_PTR ( != NULL). Hence, csdev->conns = ZERO_SIZE_PTR
which cannot be verified later to contain a valid pointer. The code which
accesses the csdev->conns is bounded by the csdev->nr_outport check,
hence we don't try to dereference the ZERO_SIZE_PTR. This patch cleans
up the csdev->conns initialisation to make sure we initialise it
properly(i.e, either NULL or valid conns array).
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch cleans up the error handling path for tmc_probe
as a side effect of the removal of the spurious dma_free_coherent().
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit de5461970b ("coresight: tmc: allocating memory when needed")
removed the static allocation of buffer for the trace data in ETR mode in
tmc_probe. However it failed to remove the "devm_free_coherent" in
tmc_probe when the probe fails due to other reasons. This patch gets
rid of the incorrect dma_free_coherent() call.
Fixes: commit de5461970b ("coresight: tmc: allocating memory when needed")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
etm4_trace_id is not guaranteed to be executed on the CPU whose ETM is
being accessed. This leads to exception similar to below one if the
CPU whose ETM is being accessed is in deeper idle states. So it must
be executed on the CPU whose ETM is being accessed.
Unhandled fault: synchronous external abort (0x96000210) at 0xffff000008db4040
Internal error: : 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 5 PID: 5979 Comm: etm.sh Not tainted 4.7.0-rc3 #159
Hardware name: ARM Juno development board (r2) (DT)
task: ffff80096dd34b00 ti: ffff80096dfe4000 task.ti: ffff80096dfe4000
PC is at etm4_trace_id+0x5c/0x90
LR is at etm4_trace_id+0x3c/0x90
Call trace:
etm4_trace_id+0x5c/0x90
coresight_id_match+0x78/0xa8
bus_for_each_dev+0x60/0xa0
coresight_enable+0xc0/0x1b8
enable_source_store+0x3c/0x70
dev_attr_store+0x18/0x28
sysfs_kf_write+0x48/0x58
kernfs_fop_write+0x14c/0x1e0
__vfs_write+0x1c/0x100
vfs_write+0xa0/0x1b8
SyS_write+0x44/0xa0
el0_svc_naked+0x24/0x28
However, TRCTRACEIDR is not guaranteed to hold the previous programmed
trace id if it enters deeper idle states. Further, the trace id that is
computed in etm4_init_trace_id is programmed into TRCTRACEIDR only in
etm4_enable_hw which happens much later in the sequence after
coresight_id_match is executed from enable_source_store.
This patch simplifies etm4_trace_id by returning the stashed trace id
value similar to etm4_cpu_id.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CoreSight STM device allows direct mapping of the channel regions to
userspace for zero-copy writing. To support this ability, the STM
framework has provided a hook 'mmio_addr', this patch just implemented
this hook for CoreSight STM.
This patch also added an item into 'channel_space' to save the physical
base address of channel region which mmap operation needs to know.
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the addition of the coresight devices get deferred, then there's a
window before child_name is populated by of_get_coresight_platform_data
from the respective component driver's probe and the attempted to access
the same from coresight_orphan_match resulting in kernel NULL pointer
dereference as below:
Unable to handle kernel NULL pointer dereference at virtual address 0x0
Internal error: Oops: 96000004 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1038 Comm: kworker/0:1 Not tainted 4.7.0-rc3 #124
Hardware name: ARM Juno development board (r2) (DT)
Workqueue: events amba_deferred_retry_func
PC is at strcmp+0x1c/0x160
LR is at coresight_orphan_match+0x7c/0xd0
Call trace:
strcmp+0x1c/0x160
bus_for_each_dev+0x60/0xa0
coresight_register+0x264/0x2e0
tmc_probe+0x130/0x310
amba_probe+0xd4/0x1c8
driver_probe_device+0x22c/0x418
__device_attach_driver+0xbc/0x158
bus_for_each_drv+0x58/0x98
__device_attach+0xc4/0x160
device_initial_probe+0x10/0x18
bus_probe_device+0x94/0xa0
device_add+0x344/0x580
amba_device_try_add+0x194/0x238
amba_deferred_retry_func+0x48/0xd0
process_one_work+0x118/0x378
worker_thread+0x48/0x498
kthread+0xd0/0xe8
ret_from_fork+0x10/0x40
This patch adds a check for non-NULL conn->child_name before accessing
the same.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver has an asymmetry of ONLINE code without any corresponding tear
down code. Otherwise, this is a straightforward conversion.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.228918408@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This driver has an asymmetry of ONLINE code without any corresponding tear
down code. Otherwise, this is a straightforward conversion.
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153337.147128995@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Enabling a component via sysfs (echo 1 > enable_source), would
trigger building a path from the enabled sources to the sink.
If there is an error in the process (e.g, sink not enabled or
the device (CPU corresponding to ETM) is not online), we never report
failure, except for leaving a message in the dmesg.
Do proper error checking for the build path and return the error.
Before:
$ echo 0 > /sys/devices/system/cpu/cpu2/online
$ echo 1 > /sys/devices/cs_etm/cpu2/enable_source
$ echo $?
0
After:
$ echo 0 > /sys/devices/system/cpu/cpu2/online
$ echo 1 > /sys/devices/cs_etm/cpu2/enable_source
-bash: echo: write error: No such device or address
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of a trace collection, we try to clear the entire buffer
and enable the ETR back if it was already enabled. But, we would have
adjusted the drvdata->buf to point to the beginning of the trace data
in the trace buffer @drvdata->vaddr. So, the following code which
clears the buffer is dangerous and can cause crashes, like below :
memset(drvdata->buf, 0, drvdata->size);
Unable to handle kernel paging request at virtual address ffffff800a145000
pgd = ffffffc974726000
*pgd=00000009f3e91003, *pud=00000009f3e91003, *pmd=0000000000000000
PREEMPT SMP
Modules linked in:
CPU: 4 PID: 1692 Comm: dd Not tainted 4.7.0-rc2+ #1721
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc9734a0080 ti: ffffffc974460000 task.ti: ffffffc974460000
PC is at __memset+0x1ac/0x200
LR is at tmc_read_unprepare_etr+0x144/0x1bc
pc : [<ffffff80083a05ac>] lr : [<ffffff800859c984>] pstate: 200001c5
...
[<ffffff80083a05ac>] __memset+0x1ac/0x200
[<ffffff800859b2e4>] tmc_release+0x90/0x94
[<ffffff8008202f58>] __fput+0xa8/0x1ec
[<ffffff80082030f4>] ____fput+0xc/0x14
[<ffffff80080c3ef8>] task_work_run+0xb0/0xe4
[<ffffff8008088bf4>] do_notify_resume+0x64/0x6c
[<ffffff8008084d5c>] work_pending+0x10/0x14
Code: 91010108 54ffff4a 8b040108 cb050042 (d50b7428)
Since we clear the buffer anyway in the following call to
tmc_etr_enable_hw(), remove the erroneous memset().
Fixes: commit de5461970b ("coresight: tmc: allocating memory when needed")
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the end of the trace capture, we free the allocated memory,
resetting the drvdata->buf to NULL, to indicate that trace data
was collected and the next trace session should allocate the
memory in tmc_enable_etr_sink_sysfs.
The tmc_enable_etr_sink_sysfs, we only allocate memory if drvdata->vaddr
is not NULL (which is not performed at the end of previous session).
This can cause, drvdata->vaddr getting assigned NULL and later we do
memset() which causes a crash as below :
Unable to handle kernel NULL pointer dereference at virtual
address 00000000
pgd = ffffffc9747f0000
[00000000] *pgd=00000009f402e003, *pud=00000009f402e003,
*pmd=0000000000000000
Internal error: Oops: 96000046 [#1] PREEMPT SMP
Modules linked in:
CPU: 0 PID: 1592 Comm: bash Not tainted 4.7.0-rc1+ #1712
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc078fe0080 ti: ffffffc974178000 task.ti: ffffffc974178000
PC is at __memset+0x1ac/0x200
LR is at tmc_enable_etr_sink+0xf8/0x304
pc : [<ffffff80083a002c>] lr : [<ffffff800859be44>] pstate: 400001c5
sp : ffffffc97417bc00
x29: ffffffc97417bc00 x28: ffffffc974178000
Call trace:
Exception stack(0xffffffc97417ba40 to 0xffffffc97417bb60)
ba40: 0000000000000001 ffffffc974a5d098 ffffffc97417bc00 ffffff80083a002c
ba60: ffffffc974a5d118 0000000000000000 0000000000000000 0000000000000000
ba80: 0000000000000001 0000000000000000 ffffff800859bdec 0000000000000040
baa0: ffffff8008b45b58 00000000000001c0 ffffffc97417baf0 ffffff80080eddb4
bac0: 0000000000000003 ffffffc078fe0080 ffffffc078fe0960 ffffffc078fe0940
bae0: 0000000000000000 0000000000000000 00000000007fffc0 0000000000000004
bb00: 0000000000000000 0000000000000040 000000000000003f 0000000000000000
bb20: 0000000000000000 0000000000000000 0000000000000000 0000000000000001
bb40: ffffffc078fe0960 0000000000000018 ffffffffffffffff 0008669628000000
[<ffffff80083a002c>] __memset+0x1ac/0x200
[<ffffff8008599814>] coresight_enable_path+0xa8/0x1dc
[<ffffff8008599b10>] coresight_enable+0x88/0x1b8
[<ffffff8008599d88>] enable_source_store+0x3c/0x6c
[<ffffff800845eaf4>] dev_attr_store+0x18/0x28
[<ffffff80082829e8>] sysfs_kf_write+0x54/0x64
[<ffffff8008281c30>] kernfs_fop_write+0x148/0x1d8
[<ffffff8008200128>] __vfs_write+0x28/0x110
[<ffffff8008200e88>] vfs_write+0xa0/0x198
[<ffffff80082021b0>] SyS_write+0x44/0xa0
[<ffffff8008084e70>] el0_svc_naked+0x24/0x28
Code: 91010108 54ffff4a 8b040108 cb050042 (d50b7428)
This patch fixes the issue by clearing the drvdata->vaddr while we free
the allocated buffer at the end of a session, so that we allocate the
memory again.
Cc: mathieu.poirier@linaro.org
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
_coresight_build_path assumes that all the connections of a csdev
has the child_dev initialised. This may not be true if the particular
component is not supported by the kernel config(e.g TPIU) but is
present in the DT. In which case, building a path can cause a crash like this :
Unable to handle kernel NULL pointer dereference at virtual address 00000010
pgd = ffffffc9750dd000
[00000010] *pgd=00000009f5e90003, *pud=00000009f5e90003, *pmd=0000000000000000
Internal error: Oops: 96000006 [#1] PREEMPT SMP
Modules linked in:
CPU: 4 PID: 1348 Comm: bash Not tainted 4.6.0-next-20160517 #1646
Hardware name: ARM Juno development board (r0) (DT)
task: ffffffc97517a280 ti: ffffffc9762c4000 task.ti: ffffffc9762c4000
PC is at _coresight_build_path+0x18/0xe4
LR is at _coresight_build_path+0xc0/0xe4
pc : [<ffffff80083d5130>] lr : [<ffffff80083d51d8>] pstate: 20000145
sp : ffffffc9762c7ba0
[<ffffff80083d5130>] _coresight_build_path+0x18/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d51d8>] _coresight_build_path+0xc0/0xe4
[<ffffff80083d5cdc>] coresight_build_path+0x40/0x68
[<ffffff80083d5e14>] coresight_enable+0x74/0x1bc
[<ffffff80083d60a0>] enable_source_store+0x3c/0x6c
[<ffffff800830b17c>] dev_attr_store+0x18/0x28
[<ffffff80081ca9c4>] sysfs_kf_write+0x40/0x50
[<ffffff80081c9e38>] kernfs_fop_write+0x140/0x1cc
[<ffffff8008163ec8>] __vfs_write+0x28/0x110
[<ffffff8008164bf0>] vfs_write+0xa0/0x174
[<ffffff8008165d18>] SyS_write+0x44/0xa0
[<ffffff8008084e70>] el0_svc_naked+0x24/0x28
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The read pointer (read_ptr) needs to be adjusted only if its value
has gone beyond the length of the memory buffer.
Reported-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When part of a path but not identified as a sink, the EFT has to
be configured as a link and placed in HW FIFO mode. As such when
enabling a path, call the right configuration function based on
the role the ETF if playing in this trace run.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch implement the AUX area interfaces required to
use the TMC (configured as an ETF) from the Perf sub-system.
The heuristic is heavily borrowed from the ETB10 implementation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That way we can re-use the structure in other drivers.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Accessing the HW configuration register each time the memory
width is needed simply doesn't make sense. It is much more
efficient to read the value once and keep a reference for
later use.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysFS and Perf access methods can't be allowed to interfere
with one another. As such introducing guards to access
functions that prevents moving forward if a TMC is already
being used.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Calling tmc_etf/etr_dump_hw() is required only when operating from
sysFS. When working from Perf, the system memory is harvested
from the AUX trace API.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Moving tmc_drvdata::enable to a local_t mode. That way the
sink interface is aware of it's orgin and the foundation for
mutual exclusion between the sysFS and Perf interface can be
laid out.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allowing multiple readers to access the trace data simultaniously
via sysFS provides no shortage of opportunity for race condition,
mandates two variable to be maintained (drvdata::read_count and
drvdata::reading), makes the code complex and provide little
advantages, if any.
This patch streamlines the read process by restricting trace data
access to a single user. That way drvdata::read_count can
be eliminated and race conditions (along with faulty error handling)
in function tmc_open() and tmc_release() eliminated.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In it's current form the TMC probe() function allocates
trace buffer memory at boot time, event if coresight isn't
used. This is highly inefficient since trace buffers can
occupy a lot of memory that could be used otherwised.
This patch allocates trace buffers on the fly, when the
coresight subsystem is solicited. Allocated buffers are
released when traces are read using the device descriptors
under /dev.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dealing with HW related matters in tmc_read_prepare/unprepare
becomes convoluted when many cases need to be handled distinctively.
As such moving processing related to HW setup to individual driver
files and keep the core driver generic.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TMC block can operate in 3 modes (ETB, ETF and ETR) and accessed
via two interfaces (sysFS and Perf). That makes 6 mode to cover, which
is way too much coupling for a single file.
This patch splits the original TMC driver in 2 halves, one for ETB/ETF
and another one for ETR mode. A common core is kept for functionality
common to all 3 modes.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch first move the TMC_STS_TMCREADY_BIT and
TMC_FFCR_FLUSHMAN_BIT defines to their respective section.
It also removes TMC_FFCR_FLUSHMAN, since the same result
can easily be obtained using the BIT() macro.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The amount of #define, enumeration and structure definition
is big enough to justify moving them to a new header file.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes the name of the define reflect the amount of
data tranfers per burst, in this case 16.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In their current implementation the tmc_read_prepare/unprepare()
are a lump of if/else that is difficult to read. This patch is
alleviating that by using a switch statement. The latter also
allows for a better control on the error path.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the TRM before programming the TMC in circular
buffer mode (and that for any configuration, ETB, ETR, ETF),
the TMCReady bit in the status register has to be set.
This patch adds a check to make sure the state machine is in
a state where it can be configured, and complains otherwise.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
According to the TMC architectural state machine, the 'stopped'
state is reached when bit 2 (TMCReady) of the TMC Status register
turns to '1'. The code is correct but the naming convention isn't.
The 'Triggered' bit occupies position '1' of the TMC Status register
and has nothing to do with the indication of the TMC entering the
stopped state. As such renaming function "tmc_wait_for_triggered()"
and changing the #define to reflect what the code is really doing.
This patch has no effect other than clarifying the semantic.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding management registers that convey implementation
specific characteristics. Those are useful for trace
configuration and collection along with general trouble
shooting.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a cellID for the ETMv4 tracer found on
HiSillicon's A72 Maia processor.
Signed-off-by: Li Pengcheng <lipengcheng8@huawei.com>
Signed-off-by: Li Zhong <lizhong11@hisilicon.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch rectifies the amount of words to read when the internal
buffer is deemed bigger than the amount of space available in the
perf ring buffer.
The amount to read is set to the amount of space in the perf ring
buffer rather than being subtracted by it.
Reported-by: Suzuki K Poulose <Suzuki.Poulose@arm.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver adds support for the STM CoreSight IP block, allowing any
system compoment (HW or SW) to log and aggregate messages via a
single entity.
The CoreSight STM exposes an application defined number of channels
called stimulus port. Configuration is done using entries in sysfs
and channels made available to userspace via configfs.
Signed-off-by: Pratik Patel <pratikp@codeaurora.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Reviewed-by: Michael Williams <michael.williams@arm.com>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
>From a core framework point of view an STM device is a source that is
treated the same way as any other tracers. Unlike tracers though STM
devices are not associated with a CPU. As such it doesn't make sense
to associate the path from an STM device to its sink with a per-cpu
variable as it is done for tracers.
This patch simply adds another global variable to keep STM paths and the
processing in coresight_enable/disable() is updated to deal with STM
devices properly.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Because this operation exceed the range of boolean,
so we should modify q_support to unit8 bit.
drvdata->q_support = BMVAL(etmidr0, 15, 16)
Signed-off-by: Li Pengcheng <lipengcheng8@huawei.com>
Signed-off-by: Li Zhong <lizhong11@hisilicon.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
activated and enable are already unsigned type,
no need to change them to unsigned.
Signed-off-by: Li Pengcheng <lipengcheng8@huawei.com>
Signed-off-by: Li Zhong <lizhong11@hisilicon.com>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removing boot time log for drivers that don't report useful information
other than they came up properly. The same information can be found in
sysFS once the system has booted and as such doesn't provide any value
in the boot log.
Reported-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sysFS "status" entry conveys a wealth of information about
the status of the HW but goes agains the sysFS rule of one topic
per file.
This patch rectify the situation by adding read-only entries for
each of the field formaly displayed by "status". The ABI
documentation is kept up to date.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Macro "coresight_simple_func()" can be used by several drivers.
As such making the structure type generic and moving to a
globally available header file. That way individual drivers
can use the functionality by simply specifying the structure
they need to work with.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding a set of API allowing the Perf core to treat ETMv4
tracers like other PMUs.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding new mode to limit tracing to kernel or user space.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similarly to ETMv3, moving etmv4_drvdata::enable to an atomic
type that gives the 'mode' of a tracer and prevents multiple,
simultanious access by different subsystems.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with the ETMv3.x driver, calling 'smp_call_function_single()'
twice in a row is highly ineffective. As such moving function
'etm4_os_unlock()' before the default initialisation takes
place, which results in the same outcome.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Splitting and updating the default initialisation for each etmv4
configuration so that it can be called at the beginning of each
session rather than initialisation time only.
Since the trace ID isn't expected to change with every session,
moving it with the default tracer initialisation.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Similar to what was done on etm3x, splitting driver structure
etmv4_drvdata in two. One half is concerned with the HW
characteristics that are generally static in nature. The other
half deals with user configuration and will change from one
trace session to another.
No gain/loss of functionality is incurred from this patch.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adding new sysFS management interface to query the configuration
and the traceid registers. Both are required to convey information
to the perf cmd line tools when using ETMv4 tracers as PMU.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As with the etm3x driver, sysFS entries are big enough to justify
their own file. As such moving all sysFS related declarations to
a dedicated location.
No gain/loss of functionality is incurred from this patch.
Signed-off-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
