After commit 74d905d2d3 devices requiring the workaround for edge
triggered interrupts stopped working.
The hardware needs the quirk to be used before even proceeding to
check if the quirk is needed because mxt_acquire_irq() is called
before mxt_check_retrigen() is called and at this point pending IRQs
need to be checked, and if the workaround is not active, all
interrupts will be lost from this point.
Solve this by switching the calls around.
Reported-by: Andre Müller <andre.muller@web.de>
Tested-by: Andre Müller <andre.muller@web.de>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 74d905d2d3 ("Input: atmel_mxt_ts - only read messages in mxt_acquire_irq() when necessary")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201201123026.1416743-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds the code for the Atmel touchscreens such as mXT224 to obtain
power regulators for the supply voltages AVDD and VDD. On mobile phones
such as Samsung GT-I8190 (Golden) this is needed to explicitly bring power
online.
We just enable the regulators at probe() and disable them at remove()
or in the error path for now.
As regulators are naturally stubbed if not available, this should have no
impact on existing systems.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-3-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The workaround of reading all messages until an invalid is received is a
way of forcing the CHG line high, which means that when using
edge-triggered interrupts the interrupt can be acquired.
With level-triggered interrupts the workaround is unnecessary.
Also, most recent maXTouch chips have a feature called RETRIGEN which, when
enabled, reasserts the interrupt line every cycle if there are messages
waiting. This also makes the workaround unnecessary.
Note: the RETRIGEN feature is only in some firmware versions/chips, it's
not valid simply to enable the bit.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
(cherry picked from ndyer/linux/for-upstream commit 1ae4e8281e491b22442cd5acdfca1862555f8ecb)
[gdavis: Fix conflicts due to v4.6-rc7 commit eb43335c40 ("Input:
atmel_mxt_ts - use mxt_acquire_irq in mxt_soft_reset").]
Signed-off-by: George G. Davis <george_davis@mentor.com>
[jiada: reset use_retrigen_workaround at beginning of mxt_check_retrigen()
call mxt_check_retrigen() after mxt_acquire_irq() in mxt_initialize()
replace white-spaces with tab for MXT_COMMS_RETRIGEN
Changed to check if IRQ is level type]
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Link: https://lore.kernel.org/r/20200727151637.23810-1-jiada_wang@mentor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_report_slot_state() ignores "tool" argument when the slot is
closed, which has caused a bit of confusion. Let's introduce
input_mt_report_slot_inactive() to report inactive slot state.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Link: https://lore.kernel.org/r/20200508055656.96389-2-jiada_wang@mentor.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Across suspend and resume, we are seeing error messages like the following:
atmel_mxt_ts i2c-PRP0001:00: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts i2c-PRP0001:00: Failed to read T44 and T5 (-121)
This occurs because the driver leaves its IRQ enabled. Upon resume, there
is an IRQ pending, but the interrupt is serviced before both the driver and
the underlying I2C bus have been resumed. This causes EREMOTEIO errors.
Disable the IRQ in suspend, and re-enable it on resume. If there are cases
where the driver enters suspend with interrupts disabled, that's a bug we
should fix separately.
Signed-off-by: Evan Green <evgreen@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- an update to Elan touchpad SMBus driver to fetch device parameters
(size, resolution) while it is still in PS/2 mode, before switching
over to SMBus, as in that mode some devices return garbage dimensions
- update to iforce joystick driver
- miscellaneous driver fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (48 commits)
Input: gpio_keys_polled - allow specifying name of input device
Input: edt-ft5x06 - simplify event reporting code
Input: max77650-onkey - add MODULE_ALIAS()
Input: atmel_mxt_ts - fix leak in mxt_update_cfg()
Input: synaptics - enable SMBUS on T480 thinkpad trackpad
Input: atmel_mxt_ts - fix -Wunused-const-variable
Input: joydev - extend absolute mouse detection
HID: quirks: Refactor ELAN 400 and 401 handling
Input: elan_i2c - export the device id whitelist
Input: edt-ft5x06 - use get_unaligned_be16()
Input: iforce - add the Saitek R440 Force Wheel
Input: iforce - use unaligned accessors, where appropriate
Input: iforce - drop couple of temps from transport code
Input: iforce - drop bus type from iforce structure
Input: iforce - use DMA-safe buffores for USB transfers
Input: iforce - allow callers supply data buffer when fetching device IDs
Input: iforce - only call iforce_process_packet() if initialized
Input: iforce - signal command completion from transport code
Input: iforce - do not combine arguments for iforce_process_packet()
Input: iforce - factor out hat handling when parsing packets
...
Fix leak (whose magnitude is the configuration file size) when the CRCs
match in mxt_update_cfg().
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Clang produces the following warning
drivers/input/touchscreen/atmel_mxt_ts.c:259:42: warning: unused
variable 'mxt_video_fops' [-Wunused-const-variable]
static const struct v4l2_file_operations mxt_video_fops = {
Since mxt_video_fops is only used inside an ifdef. It should
be moved inside the ifdef.
Link: https://github.com/ClangBuiltLinux/linux/issues/527
Signed-off-by: Nathan Huckleberry <nhuck@google.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the user attempts to update Atmel device with an invalid configuration
cfg file, error handling code is trying to free cfg file memory which is
not allocated yet hence results into kernel crash.
This patch fixes the order of memory free operations.
Signed-off-by: Sanjeev Chugh <sanjeev_chugh@mentor.com>
Fixes: a4891f1058 ("Input: atmel_mxt_ts - zero terminate config firmware file")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Both v4.16-rc7 commit 93afb1d6e7 ("Input: atmel_mxt_ts - switch from
OF to generic device properties") and v4.16-rc7 commit 96a938aa21
("Input: atmel_mxt_ts - remove platform data support") added includes of
"<linux/property.h>". Remove one of the duplicate includes to fix this.
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If T9.CTRL DISAMP is set, then pressure is reported as zero. This means
some app layers (eg tslib) will ignore the contact.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We use sscanf to parse the configuration file, so it's necessary to zero
terminate the configuration otherwise a truncated file can cause the
parser to run off into uninitialised memory.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On devices with the T71 object, the config CRC will start there, rather
than at T7.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver only registers one input device, which uses the screen
parameters from the first T9 instance. The first T63 instance also uses
those parameters.
It is incorrect to send input reports from the second instances of these
objects if they are enabled: the input scaling will be wrong and the
positions will be mashed together.
This also causes problems on Android if the number of slots exceeds 32.
In the future, this could be handled by looking for enabled touch object
instances and creating an input device for each one.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The current reset-gpio support triggers an interrupt storm on platforms
using the maxtouch with level based interrupt. The Motorola Droid 4,
which I used for some of the tests is not affected, since it uses a edge
based interrupt.
This change avoids the interrupt storm by enabling the device while its
interrupt is disabled. Afterwards we wait 100ms. This is important for
two reasons: The device is unresponsive for some time (~22ms for
mxt224E) and the CHG (interrupt) line is not working properly for 100ms.
We don't need to wait for any following interrupts, since the following
mxt_initialize() checks for bootloader mode anyways.
This fixes a boot issue on GE PPD (watchdog kills device due to
interrupt storm) and does not cause regression on Motorola Droid 4.
Fixes: f657b00df2 ("Input: atmel_mxt_ts - add support for reset line")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver needs help determining whether it is dealing with a touchscreen
or a touchpad, and with button mapping. Previously we supported passing
this data via device properties, and also had DMI lists for Chromebooks
that specified Atmel devices in ACPI, but did not provide enough data
there. Now that chromeos_laptop driver is adjusted to supply necessary
device properties even for ACPI devices, we can drop the DMI tables and
refuse to probe if device properties are not attached to the device.
We use presence of "compatible" property to determine if device properties
are attached to the device or not and rely on chromeos_laptop to re-probe
the device after attaching missing device properties to it.
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Just a few driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - add missing compatible strings to OF device table
Input: atmel_mxt_ts - fix the firmware update
Input: atmel_mxt_ts - add touchpad button mapping for Samsung Chromebook Pro
MAINTAINERS: Rakesh Iyer can't be reached anymore
Input: hideep_ts - fix a typo in Kconfig
Input: alps - fix reporting pressure of v3 trackstick
Input: leds - fix out of bound access
Input: synaptics-rmi4 - fix an unchecked out of memory error path
Commit af503716ac ("i2c: core: report OF style module alias for devices
registered via OF") fixed how the I2C core reports the module alias when
devices are registered via OF.
But the atmel_mxt_ts driver only has an "atmel,maxtouch" compatible in its
OF device ID table, so if a Device Tree is using a different one, autoload
won't be working for the module (the matching works because the I2C device
ID table is used as a fallback).
So add compatible strings for each of the entries in the I2C device table.
Fixes: af503716ac ("i2c: core: report OF style module alias for devices registered via OF")
Reported-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Rob Herring <robh@kernel.org>
[dtor: document which compatibles are deprecated and should not be used]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The automatic update mechanism will trigger an update if the
info block CRCs are different between maxtouch configuration
file (maxtouch.cfg) and chip.
The driver compared the CRCs without retrieving the chip CRC,
resulting always in a failure and firmware flashing action
triggered. Fix this issue by retrieving the chip info block
CRC before the check.
Note that this solution has the benefit that by reading the
information block and the object table into a contiguous region
of memory, we can verify the checksum at probe time. This means
we make sure that we are indeed talking to a chip that supports
object protocol correctly.
Using this patch on a kevin chromebook, the touchscreen and
touchpad drivers are able to match the CRC:
atmel_mxt_ts 3-004b: Family: 164 Variant: 14 Firmware V2.3.AA Objects: 40
atmel_mxt_ts 5-004a: Family: 164 Variant: 17 Firmware V2.0.AA Objects: 31
atmel_mxt_ts 3-004b: Resetting device
atmel_mxt_ts 5-004a: Resetting device
atmel_mxt_ts 3-004b: Config CRC 0x573E89: OK
atmel_mxt_ts 3-004b: Touchscreen size X4095Y2729
input: Atmel maXTouch Touchscreen as /devices/platform/ff130000.i2c/i2c-3/3-004b/input/input5
atmel_mxt_ts 5-004a: Config CRC 0x0AF6BA: OK
atmel_mxt_ts 5-004a: Touchscreen size X1920Y1080
input: Atmel maXTouch Touchpad as /devices/platform/ff140000.i2c/i2c-5/5-004a/input/input6
Signed-off-by: Nick Dyer <nick.dyer@shmanahar.org>
Acked-by: Benson Leung <bleung@chromium.org>
[Ezequiel: minor patch massage]
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds the correct platform data information for the Caroline
Chromebook, so that the mouse button does not get stuck in pressed state
after the first click.
The Samus button keymap and platform data definition are the correct
ones for Caroline, so they have been reused here.
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Salvatore Bellizzi <lkml@seppia.net>
Tested-by: Guenter Roeck <groeck@chromium.org>
Cc: stable@vger.kernel.org
[dtor: adjusted vendor spelling to match shipping firmware]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that there are no users of custom Atmel platform data, and everyone
has switched to the generic device properties, we can remove support for
the platform data.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Move older ChromeOS devices describing Atmel controllers in ACPI, but not
providing enough details to configure the controllers properly, from
platform data over to generic device properties. This will allow us
remove support for platform data later on, leaving only generic device
properties in place.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Instead of using OF-specific APIs to fecth device properties, let's switch
to generic device properties API. This will allow us to use device
properties on legacy ChromeOS devices and get rid of platform data down
the road.
Acked-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
The way we are supposed to put controller to sleep and wake it up does not
depend on the platform, but rather on controller itself, so we want to get
rid of suspend mode in platform data (and eventually get rid of platform
data completely). Unfortunately some early chromebooks (the original Pixel,
Acer C720) were shipped with config that requires manually re-enabling
touch reporting in T9. We will sort it out, but in the meantime let's
switch to a simple DMI quirk.
We'll keep pdata->suspend_mode for now and remove it when we rework
chromeos-laptop driver.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Benson Leung <bleung@chromium.org>
Provide support for controlling reset pin. If this is not driven
correctly the device will be held in reset and will not respond.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Switch mxt_data and interrupt to resource managed allocation methods,
which cleans up the driver slightly and prepares for adding
reset GPIO support.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When using the 'object' sysfs attribute, T100 is not displayed in
the output.
Signed-off-by: Maxime Roussin-Bélanger <maxime.roussinbelanger@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If a function declares a variable to access a structure element,
use it consistently.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add copyright lines for Zodiac who paid for the V4L touch work.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
There are different datatypes available from a maXTouch chip. Add
support to retrieve reference data as well.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The mXT1386 family of chips have a different architecture which splits
the diagnostic data into 3 columns.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Invert the diagnostic data to match the orientation of the input device.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen may have a margin where not all the matrix is used. Read
the parameters from T9 and T100 and take account of the difference.
Note: this does not read the XORIGIN/YORIGIN fields so it assumes that
the touchscreen starts at (0,0)
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Atmel maXTouch devices have a T37 object which can be used to read raw
touch deltas from the device. This consists of an array of 16-bit
integers, one for each node on the touchscreen matrix.
Signed-off-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If using IRQF_TRIGGER_FALLING, then there is a race here: if the reset
completes before we enable the IRQ, then CHG is already low and touch
will be broken.
This has been seen on Chromebook Pixel 2.
A workaround is to reconfig T18 COMMSCONFIG to enable the RETRIGEN bit
using mxt-app:
mxt-app -W -T18 44
mxt-app --backup
Tested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
