Add DT earlycon for 8250_omap driver. This boot console is included
for kernels built with CONFIG_SERIAL_EARLYCON=y, CONFIG_OF=y,
CONFIG_SERIAL_8250_OMAP=y, and CONFIG_OF_EARLY_FLATTREE=y.
This boot console is enabled with the command line option "earlycon"
(without "=<name>...") when the DT 'stdout-path' property matches a
compatible uart. For example,
/ {
chosen {
stdout-path = "serial0:115200";
};
....
aliases {
serial0 = &uart0;
};
....
ocp : ocp {
uart0 : serial@44e09000 {
compatible = "ti,omap3-uart";
}
};
};
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
earlycon initializes struct uart_port::regshift to the correct
value for UPIO_MEM32 already. Use the port field rather than
hard-coded value.
This enables broader support for various i/o access methods in
8250 earlycon (eg., omap8250 earlycon).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, 8-bit (MMIO) and 32-bit (MMIO32) register interfaces are
supported for the 8250 console, but the 16-bit (MMIO16) is not.
The 8250 UART device on my board is connected to a 16-bit bus and
my main motivation is to use earlycon with it.
(Refer to arch/arm/boot/dts/uniphier-support-card.dtsi)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, wait_for_xmitr() is only called from serial_putc(), and both
are short enough. They can be merged into a single function.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current code waits until the transmitter becomes empty,
before sending each character, and after finishing the whole string.
This seems a bit redundant.
It can be more efficient by checking the transmitter only after sending
each character. This should be safe because the transmitter is already
empty at the first entry of serial_putc().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IER has already been masked in early_serial8250_setup(), there is
no reason to save and restore it every time early_serial8250_write()
is called.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This allows earlycon to be used without needing to specify the I/O
address on the kernel command line, if linux,stdout-path is specified
in the chosen node.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit ed71871bed ("tty/8250_early: Turn serial_in/serial_out into
weak symbols") made these routines weak to allow platform specific
Big endian override
However recent updates to core, specifically ebc5e20082 ("serial:
of_serial: Support big-endian register accesses") and 6e63be3fee
("serial: earlycon: Add support for big-endian MMIO accesses") means
that round about way to overide the early serial accessors is no longer
needed.
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Acked-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- DT endianness specification bindings
- Big endian 8250 serial support
- DT overlay unittest updates
- Various DT doc updates
- Compile fixes for OF_IRQ=n
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOG5kAAoJEMhvYp4jgsXihDgH/3pmPSjuRG1bhGssmnchHjWh
SU2eS2MZnlD60UqRt7jd3smCX2qL83tfwpFhOvCT9Mz775E7ggmYq9fS8pCYAbaD
x98mUrE2GzdUzlrL6RS8Z0ExjyGwbMoW3+cZtyPkmC6CsW0fwqEPmEyk7m+Hk8C3
w3pWG06o+G8UjiFmwbr8Pki2ykxvucr22NCzH4SS6bAD4QOrQO3v48QkUg7XFlVc
NHNzQbswL85uOJ7uuAbxg+s8TXkwcxUeMJEKldLrjuyppO3N1MjnOgCptnhVNOOb
zK+IsS378jMiNjAg2ui/BLH60N5yadkgk4+L4iPPy+y/yR61NCVXxRe11IQJxb0=
=rtv6
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull second batch of devicetree updates from Rob Herring:
"As Grant mentioned in the first devicetree pull request, here is the
2nd batch of DT changes for 4.1. The main remaining item here is the
endianness bindings and related 8250 driver support.
- DT endianness specification bindings
- big-endian 8250 serial support
- DT overlay unittest updates
- various DT doc updates
- compile fixes for OF_IRQ=n"
* tag 'devicetree-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
frv: add io{read,write}{16,32}be functions
mn10300: add io{read,write}{16,32}be functions
Documentation: DT bindings: add doc for Altera's SoCFPGA platform
of: base: improve of_get_next_child() kernel-doc
Doc: dt: arch_timer: discourage clock-frequency use
of: unittest: overlay: Keep track of created overlays
of/fdt: fix allocation size for device node path
serial: of_serial: Support big-endian register accesses
serial: 8250: Add support for big-endian MMIO accesses
of: Document {little,big,native}-endian bindings
of/fdt: Add endianness helper function for early init code
of: Add helper function to check MMIO register endianness
of/fdt: Remove "reg" data prints from early_init_dt_scan_memory
of: add vendor prefix for Artesyn
of: Add dummy of_irq_to_resource_table() for IRQ_OF=n
of: OF_IRQ should depend on IRQ_DOMAIN
Add cases for UPIO_MEM32BE wherever there are currently cases handling
UPIO_MEM32.
Signed-off-by: Kevin Cernekee <cernekee@gmail.com>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rob Herring <robh@kernel.org>
Restore undocumented behavior of kernel command line parameters of
the forms:
console=uart[8250],io|mmio|mmio32,<addr>[,options]
console=uart[8250],<addr>[,options]
where 'options' have not been specified; in this case, the hardware
is assumed to be initialized.
Fixes: c7cef0a849 ("console: Add extensible console matching")
Reported-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The serial_core.h file have been included in header file
serial_8250.h. so remove the "#include <serial_core.h>" in
some 8250 serial drivers, because they have included the header file
serial_8250.h.
Signed-off-by: Wang Long <long.wanglong@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
setup_earlycon() will now match and register the desired earlycon
from the param string (as if 'earlycon=...' had been set on the
command line). Use setup_earlycon() from existing arch call sites
which start an earlycon directly.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Earlycon matching can only be triggered if 'earlycon=...' has been
specified on the kernel command line. To workaround this limitation
requires tight coupling between arches and specific serial drivers
in order to start an earlycon. Devicetree avoids this limitation
with a link table that contains the required data to match earlycons.
Mirror this approach for earlycon match by name. Re-purpose
EARLYCON_DECLARE to generate a table entry which associates name with
setup() function. Re-purpose setup_earlycon() to scan this table for
an earlycon match, which is registered if found.
Declare one "earlycon" early_param, which calls setup_earlycon().
This design allows setup_earlycon() to be called directly with a
param string (as if 'earlycon=...' had been set on the command line).
Re-registration (either directly or by early_param) is prevented.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If parsing failed to decode a valid uart addr, return -ENODEV instead
of success. Although setup_earlycon() will detect the failure anyway
(because the write() method has not been set), that behavior is not
obvious and should not be relied on.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The <baud><parity><bit> option string is not supplied if the earlycon
is started via devicetree and OF_EARLYCON_DECLARE(). The option string
is also not required if started via kernel command line parameters of
the form:
earlycon=uart,mmio,<addr>
console=uart,mmio,<addr>
If earlycon_device->baud is 0, then an option string was not supplied.
In this case, assume the uart has already been initialized by the
bootloader or firmware.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
early_device was only required for serial8250_find_port_for_earlycon(),
which was replaced by extensible console matching.
Fixup early_serial8250_write() to get the earlycon_device * from
console->data (which is initialized by {of_}setup_earlycon()).
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add match() method to struct console which allows the console to
perform console command line matching instead of (or in addition to)
default console matching (ie., by fixed name and index).
The match() method returns 0 to indicate a successful match; normal
console matching occurs if no match() method is defined or the
match() method returns non-zero. The match() method is expected to set
the console index if required.
Re-implement earlycon-to-console-handoff with direct matching of
"console=uart|uart8250,..." to the 8250 ttyS console.
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PXA variant of the 8250 UART adds a UART enable bit which must not
be cleared. Make the earlycon support maintain this bit if it is set.
This implies some initialization of the UART, but we cannot
unconditionally set the bit as some other variants require this bit to
be clear for other functions.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In early 8250, IER is already zero so no point in writing this - twice
per line
This helped improve the SystemC model based ARC OSCI platform
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Rob Herring <robh@kernel.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the conversion to generic early console, the passing of options from
the early 8250 console to the regular ttyS console was broken. This
resulted in the baud rate changing when switching consoles during boot.
This feature allows specifying a single console option on the kernel
command line rather than both an early console and regular serial tty
console. It would be nice to generalize this feature. However, it only
works if the correct baud rate can be probed early which is not the
case on many platforms which have non-standard UART clock rates. So for
now, this is left as an 8250 specific feature.
Reported-and-tested-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d2fd6810a8 (tty/serial: convert 8250 to generic earlycon)
removed setup_early_serial8250_console, but there are still 2 callers
in:
arch/mips/mti-malta/malta-init.c
drivers/firmware/pcdp.c
Add back the function implemented as a wrapper to setup_earlycon.
Reported-by: Yinghai Lu <yinghai@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With the generic earlycon infrastructure in place, convert the 8250
early console to use it.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following sparse warning:
drivers/tty/serial/8250/8250_early.c:196:26: error: incompatible types in comparison expression (different type sizes)
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The earlier change to use strlcpy uncovered a bug in the options
argument length calculation causing last character to be truncated.
This makes the actual console to be configured with incorrect
baudrate when specifying the console using console=uart,... syntax.
Bug symptom seen in kernel log output:
Kernel command line: console=uart,mmio,0x90000000,115200
Early serial console at MMIO 0x90000000 (options '11520')
which then results in a invalid baud rate 11520 instead of the
expected 115200 when the console is switched to ttyS0 later
in the boot process.
Signed-off-by: Henrik Nordstrom <henrik@henriknordstrom.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fields must be null-terminated, or next printk for %s, will cause issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Allows overriding default methods serial_in/serial_out.
In such platform specific replacement it is possible to use
other regshift, biased register offset, any other manipulation
that is not covered with common default methods.
Overriding default methods may be useful for platforms which got
serial peripheral with registers represented in big endian.
In this situation and assuming that 32 bit operations / alignment
is required then it may be useful to swab words before/after
accessing the serial registers.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modify divisor to select the nearest baud rate divider rather than the
lowest. It minimizes baud rate errors especially on low UART clock
frequencies.
For example, if uartclk is 33000000 and baud is 115200 the ratio is
about 17.9 The current code selects 17 (5% error) but should select 18
(0.5% error).
This 5% error in baud rate leads to garbage on receiving end, while 0.5%
doesn't.
The issue showed up when using the stock 8250 driver for
Synopsys DW UART. This was on a FPGA with ~12MHz UART clock.
When we enabled early serial, we saw garbage which was narrowed down
to the rounding error.
So the bug had been latent and it only showed up with such low clock rates.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The drivers/tty/serial dir is already getting rather busy.
Relocate the 8250 related drivers to their own subdir to
reduce the clutter.
Note that sunsu.c is not included in this move -- it is
8250-like hardware, but it does not use any of the existing
infrastructure -- and does not depend on SERIAL_8250.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
