User reports an issue in Ubuntu about the device switch upon playback.
We find the FLL will disalbe when switching headphone to speaker.
The pulseaudio will stop the headphone and close its power. Then,
it just opens the speaker and turn on its power. Therefore,
the supply of system clock does the OFF event and disables FLL.
But the FLL doesn't enable again when the speaker powers on.
The patch adds the recovery of system clock to enable FLL again
for this case. And it covers the case that system clock from MCLK.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Recently released USB Audio Class 3.0 specification
introduces many significant changes comparing to
previous versions, like
- new Power Domains, support for LPM/L1
- new Cluster descriptor
- changed layout of all class-specific descriptors
- new High Capability descriptors
- New class-specific String descriptors
- new and removed units
- additional sources for interrupts
- removed Type II Audio Data Formats
- ... and many other things (check spec)
It also provides backward compatibility through
multiple configurations, as well as requires
mandatory support for BADD (Basic Audio Device
Definition) on each ADC3.0 compliant device
This patch adds initial support of UAC3 specification
that is enough for Generic I/O Profile (BAOF, BAIF)
device support from BADD document.
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've observed too long probe time with Coffee Lake (CFL) machines,
and the likely cause is some communication problem between the
HD-audio controller and the codec chips. While the controller expects
an IRQ wakeup for each codec response, it seems sometimes missing, and
it takes one second for the controller driver to time out and read the
response in the polling mode.
Although we aren't sure about the real culprit yet, in this patch, we
put a workaround by forcing the polling mode as default for CFL
machines; the polling mode itself isn't too heavy, and much better
than other workarounds initially suggested (e.g. disabling
power-save), at least.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199007
Fixes: e79b0006c4 ("ALSA: hda - Add Coffelake PCI ID")
Reported-and-tested-by: Hui Wang <hui.wang@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver does not select all the codec drivers that needs.
Fix it by selecting the analog and HDMI codecs.
Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 24069b589b ("ASoC: hdmi-codec: remove multi detection support")
changed the dai_name for the HDMI Codec, breaking the rk3288_hdmi_analog
driver, which fails to register with a:
rk3288-snd-hdmi-analog sound: ASoC: CODEC DAI hdmi-hifi.0 not registered
This commit fixes the dai_name, fixing the issue.
Fixes: 24069b589b ("ASoC: hdmi-codec: remove multi detection support")
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use SET_SYSTEM_SLEEP_PM_OPS() macro instead of direct assignment to
.suspend and .resume fields.
This makes driver working after restore from hibernation.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
DA7219 is clock master for other codecs. DA7219 has exposed clock
control by using common clock framework and same is used to enable
and disable clock for all codecs in the system.
TEST=aplay -D hw:0,0 -vv <file>
arecord -D hw:0,0 -f dat -d 5 -vv <file>
aplay -D hw:0,1 -vv <file>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
BT I2S is a bi-directional dai, we will use the same
cpu dai for playback and capture.
TEST=aplay -D hw:0,0 -vv <file>
arecord -D hw:0,0 -f dat -d 5 -vv <file>
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We don't need 2 .remove callback
Fixes: 7480389fb0 ("ASoC: twl6040: replace codec to component")
Reported-by: Julia Lawall <julia.lawall@lip6.fr>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"HV" and "VREF" will be powered up when jack type detection process is
started and will be powered off when jack type detection process is finished.
It will generate an unexpected interrupt signal when they are powered
up during the capture process. Codec driver will do the jack type detection
process and we can't capture properly before the jack detection process is
finished. This patch will not power off the "HV" and "VREF" widgets if
headset is detected and it will solve the unexpected interrupt issue. As a
result, it will also solve the silence data captured at the beginning in
headset mic recording issue.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
"HV" and "VREF" will be powered up when jack type detection process is
started and will be powered off when jack type detection process is finished.
It will generate an unexpected interrupt signal when they are powered
up during the capture process. Codec driver will do the jack type detection
process and we can't capture properly before the jack detection process is
finished. This patch will not power off the "HV" and "VREF" widgets if
headset is detected and it will solve the unexpected interrupt issue. As a
result, it will also solve the silence data captured at the beginning in
headset mic recording issue.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
SSM2602 driver is broken on recent kernels (at least
since 4.9). User space applications such as amixer or
alsamixer get EIO when attempting to access codec
controls via the relevant IOCTLs.
Root cause of these failures is the regcache_hw_init
function in drivers/base/regmap/regcache.c, which
prevents regmap cache initalization from the
reg_defaults_raw element of the regmap_config structure
when registers are write only. It also disables the
regmap cache entirely when all registers are write only
or volatile as is the case for the SSM2602 driver.
Using the reg_defaults element of the regmap_config
structure rather than the reg_defaults_raw element to
initalize the regmap cache avoids the logic in the
regcache_hw_init function entirely. It also makes this
driver consistent with other ASoC codec drivers, as
this driver was the ONLY codec driver that used the
reg_defaults_raw element to initalize the cache.
Tested on Digilent Zybo Z7 development board which has
a SSM2603 codec chip connected to a Xilinx Zynq SoC.
Signed-off-by: James Kelly <jamespeterkelly@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Offload USB audio interface parsing function by
moving quirks to a specially designed location (quirks.c)
Signed-off-by: Ruslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When driver register its component to ALSA SoC, almost all drivers are
using snd_soc_register_component(), but soc-generic-dmaengine-pcm is
using snd_soc_add_component().
Existing component function had been assumed that registered component
was allocated, and it calling kfree() for it.
But, the user who used snd_soc_add_component() doesn't.
This patch uses devm_kzalloc() instead of kzalloc() for component,
and doesn't call kree() anymore.
This patch fixes commit be7ee5f32a ("ASoC: soc-generic-dmaengine-pcm:
replace platform to component").
Allwinner H3 SoC will crash without this patch.
Thanks Jernej report.
Reported-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
Validate the topology input before we dereference the pointer.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Improve the DPCM BE search debug output to make it easier to debug
issues in topologies.
Signed-off-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now when a helper for unreferencing device nodes is available
we can get rid of the local implementation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S controller can handle sample rates only up to 96000 and the CPU DAI
has already related constraint set so drop the impossible 176400, 192000
switch cases.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of sample rates lower than 44100 currently there is too low MCLK
frequency set for the CODEC. Playback fails with following errors:
$ speaker-test -c2 -t sine -f 1500 -l2 -r 32000
Sine wave rate is 1500.0000Hz
Rate set to 32000Hz (requested 32000Hz)
Buffer size range from 128 to 131072
Period size range from 64 to 65536
Using max buffer size 131072
Periods = 4
Unable to set hw params for playback: Invalid argument
Setting of hwparams failed: Invalid argument
[ 497.883700] max98090 1-0010: Invalid master clock frequency
To fix this the I2S root clock's frequency is increased, depending
on sampling rate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add Texas Instruments's PCM1789 DAC support.
It is a simple DAC and does not have many registers.
One particularity about this DAC is that the clocks must be
always enabled. Also, an entire software reset is necessary
while starting to play a sound otherwise, the clocks are not
synchronized (so the DAC is not able to send data).
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the remove callback is removed, the snd_soc_unregister_component()
is missing when remove device. Using devm_snd_soc_register_component()
instead of snd_soc_register_component().
Fixes: d06f33aed8 ("ASoC: da7210: replace codec to component")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since the remove callback is removed, the snd_soc_unregister_component()
is missing when remove device. Using devm_snd_soc_register_component()
instead of snd_soc_register_component().
Fixes: 10dc44c646 ("ASoC: wm8400: replace codec to component")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It's not necessary to unregister a component registered
with devm_snd_soc_register_component().
Fixes: f1b5bf0736 ("ASoC: mt2701/mt8173: replace platform to componen")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds syscon property for specifying soc-glue core.
Currently, soc-glue core is used for changing the state of S/PDIF
signal output pin to signal output state or Hi-Z state. After
resetting of SoC Hi-Z state is selected. This driver set to signal
output state when syscon property is available.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some HP laptops have a mute mute LED controlled by a pin VREF. The
Realtek codec driver updates the VREF via vmaster hook by calling
snd_hda_set_pin_ctl_cache().
This works fine as long as the driver is running in a normal mode.
However, when the VREF change happens during the codec being in
runtime PM suspend, the regmap access will skip and postpone the
actual register change. This ends up with the unchanged LED status
until the next runtime PM resume even if you change the Master mute
switch. (Interestingly, the machine keeps the LED status even after
the codec goes into D3 -- but it's another story.)
For improving this usability, let the driver temporarily powering up /
down only during the pin VREF change. This can be achieved easily by
wrapping the call with snd_hda_power_up_pm() / *_down_pm().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199073
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The blackfin architecture is getting removed, so the ASoC drivers
are all obsolete as well.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
structure da7219_dai_clks_ops is local to the source and does not need
to be in global scope, so make it static.
Cleans up sparse warning:
sound/soc/codecs/da7219.c:1777:22: warning: symbol 'da7219_dai_clks_ops'
was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds mixer switch for changing audio source of line-in.
We can choose one of LIN1, 2, 3, default is LIN1.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Back in 2013, runtime PM for GPUs with integrated HDA controller was
introduced with commits 0d69704ae3 ("gpu/vga_switcheroo: add driver
control power feature. (v3)") and 246efa4a07 ("snd/hda: add runtime
suspend/resume on optimus support (v4)").
Briefly, the idea was that the HDA controller is forced on and off in
unison with the GPU.
The original code is mostly still in place even though it was never a
100% perfect solution: E.g. on access to the HDA controller, the GPU
is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there
are no provisions to keep it resumed until access to the HDA controller
has ceased: The GPU autosuspends after 5 seconds, rendering the HDA
controller inaccessible.
Additionally, a kludge is required when hda_intel.c probes: It has to
check whether the GPU is powered down (check_hdmi_disabled()) and defer
probing if so.
However in the meantime (in v4.10) the driver core has gained a feature
called device links which promises to solve such issues in a clean way:
It allows us to declare a dependency from the HDA controller (consumer)
to the GPU (supplier). The PM core then automagically ensures that the
GPU is runtime resumed as long as the HDA controller's ->probe hook is
executed and whenever the HDA controller is accessed.
By default, the HDA controller has a dependency on its parent, a PCIe
Root Port. Adding a device link creates another dependency on its
sibling:
PCIe Root Port
^ ^
| |
| |
HDA ===> GPU
The device link is not only used for runtime PM, it also guarantees that
on system sleep, the HDA controller suspends before the GPU and resumes
after the GPU, and on system shutdown the HDA controller's ->shutdown
hook is executed before the one of the GPU. It is a complete solution.
Using this functionality is as simple as calling device_link_add(),
which results in a dmesg entry like this:
pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
The code for the GPU-governed audio power management can thus be removed
(except where it's still needed for legacy manual power control).
The device link is added in a PCI quirk rather than in hda_intel.c.
It is therefore legal for the GPU to runtime suspend to D3cold even if
the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL
is not enabled, for accesses to the HDA controller will cause the GPU to
wake up regardless if they're occurring outside of hda_intel.c (think
config space readout via sysfs).
Contrary to the previous implementation, the HDA controller's power
state is now self-governed, rather than GPU-governed, whereas the GPU's
power state is no longer fully self-governed. (The HDA controller needs
to runtime suspend before the GPU can.)
It is thus crucial that runtime PM is always activated on the HDA
controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which
is the default), lest the GPU stays awake. This is achieved by setting
the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME
flag on the HDA controller.
A side effect is that power consumption might be reduced if the GPU is
in use but the HDA controller is not, because the HDA controller is now
allowed to go to D3hot. Before, it was forced to stay in D0 as long as
the GPU was in use. (There is no reduction in power consumption on my
Nvidia GK107, but there might be on other chips.)
The code paths for legacy manual power control are adjusted such that
runtime PM is disabled during power off, thereby preventing the PM core
from resuming the HDA controller.
Note that the device link is not only added on vga_switcheroo capable
systems, but for *any* GPU with integrated HDA controller. The idea is
that the HDA controller streams audio via connectors located on the GPU,
so the GPU needs to be on for the HDA controller to do anything useful.
This commit implicitly fixes an unbalanced runtime PM ref upon unbind of
hda_intel.c: On ->probe, a runtime PM ref was previously released under
the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but
on ->remove a runtime PM ref was only acquired under the first of those
conditions. Thus, binding and unbinding the driver twice on a
vga_switcheroo capable system caused the runtime PM refcount to drop
below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag
is now always set if use_vga_switcheroo is true.
For more information on device links please refer to:
https://www.kernel.org/doc/html/latest/driver-api/device_link.html
Documentation/driver-api/device_link.rst
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/51bd38360ff502a8c42b1ebf4405ee1d3f27118d.1520068884.git.lukas@wunner.de
Purpose of having pinctrl dapm is to dynamically put the pins in
low power state when they are not actively used by the audio and
saving power.
Without this each driver has to set the pinctrl states, either
during probe or dynamically depending on the callbacks received
from ASoC core.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to achieve better DMA performance and reduce download time for
firmware and library, it is recommended to disable dynamic clock and
power gating. In some scenarios, DMA may wait to accumulate more data and
last chunk of data never gets completed if dynamic clock and power
gating is kept enabled.
This patch adds support to disable/enable dynamic clock and power gating
and use it during firmware and library download.
Signed-off-by: Rakesh Ughreja <rakesh.a.ughreja@intel.com>
Signed-off-by: Sanyog Kale <sanyog.r.kale@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the driver so, in addition to current DT bindings, it
also can also use the new DT bindings with cpu, codec subnodes which allow
to support sound on the HDMI interface.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes: ASoC: da7219: Add common clock usage for providing DAI clks
clkdev_drop usage in the codec remove function should be dependent
on if CONFIG_COMMON_CLK is defined for the platform, otherwise it
can cause build failures for platforms that do not support this.
The clkdev_* functions are still defined for those platforms, in
headers and source but the functions are not linked in.
This patch resolves this issue, so clkdev_drop is only used if
CONFIG_COMMON_CLK is defined.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just a minor simplification. Change from kcalloc() shouldn't matter
as each array element is fully initialized.
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A helper function used by snd_pcm_hw_refine() still keeps using VLA
for timestamps of hw constraint rules that are non-fixed size.
Let's replace the VLA with a simple kmalloc() array.
Reference: https://lkml.org/lkml/2018/3/7/621
Reviewed-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Icelake is a next generation Intel platform. Add PCI ID for
it.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the definitions of constants used in the dt-bindings from
include/sound/rt5651.h to include/dt-bindings/sound/rt5651.h.
As dt-bindings headers may also be parsed by the dt-compiler, they cannot
use enums, only defines, so this commit also changes the code declaring
the constants to use defines.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the change required to create the TLV data
for dapm widget kcontrols from topology. This also fixes the following
TLV read error shown in amixer while showing the card control contents.
"amixer: Control hw:1 element TLV read error: No such device or address"
Signed-off-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RCLKSRC mux input 0 is a default configuration after reset, so
there is no need for this explicit snd_soc_dai_set_sysclk() call.
Also, this static mux clock configuration can be specified in DT.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the RCLK clock may be updated through the common clk API before each
snd_soc_dai_ops::trigger call, it is not enough to update i2s->rclk_srcrate
only once after it has been initially set to 0. To avoid wrong PSR values
we always get RCLK frequency from the CLK_I2S_RCLK_SRC clock, when that
clock is available.
Fixes: e1417fdf3011 "ASoC: samsung: i2s: Ensure the RCLK rate is properly determined"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code for dereferencing device nodes in the 'codecs' array is moved
to a separate function so we can avoid open coding that in drivers.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
After the codec to component conversion codecs with custom read/write
function will no longer able to use update_bits as their io callbacks are
registered at component->driver level and not in component level.
To not complicate the code further, lets just use the
snd_soc_component_read/snd_soc_component_write function and let them sort
out the correct io function to call.
Fixes: d0ff8ba57d ("ASoC: add Component level .read/.write")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need to have the write callback to use the code.
Fixes: 7480389fb0 ("ASoC: twl6040: replace codec to component")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The control bits of ADC 1 and 2 clock are different. We have to
separate it.
Signed-off-by: Zhong An <zhongan@pinecone.net>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a fairly standard collection of fixes, there's no changes to the
core here just a bunch of small device specific changes for single
drivers plus an update to the MAINTAINERS file for the sgl5000.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlqmqZITHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0EVkB/9MrEZMqClZqWnolQJEFh6oGVRx78Lu
kZmFoO2l4lYcZuRwbVn/nYYTsJzCUIOptvQT8Sx0jM6xoBpWHftP9zUQ6TTakezt
vd/idrooS0Btbe/viiDt1ujkrrBlp8netS2IWWY66eJFQ8BrRwOkYWK+45YZFjAm
GIZ5b6+cLrZqnrcHVLYTg9nAzYOMcfRn7ma9NNhtYlqKkKLhZgHgQh6QJuJKyrGe
aZIjDbpbPQs594NH8rogbLOAJxfY5ib38Ah9OU3mHzzvK05kCARo9dU6dNs0boW8
6GABdIAujX3za/qeApfpqhwnrM5N8QBD28BkPGvH60sxxTeO8Vwm91Uf
=jIwC
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.16-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.16
This is a fairly standard collection of fixes, there's no changes to the
core here just a bunch of small device specific changes for single
drivers plus an update to the MAINTAINERS file for the sgl5000.
The control register for ADC L2 and R2 is RT5659_PWR_DIG_1
not RT5659_PWR_DIG_2.
Signed-off-by: Zhong An <zhongan@pinecone.net>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
RT5659_PWR_ADC_L2_BIT should be 2.
Signed-off-by: Zhong An <zhongan@pinecone.net>
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer 'pipe' is being initialized with a value that is never
read and it is re-assigned later, hence the initialization is redundant
and can be removed. Also remove pointer 'runtime' as it is no longer
required.
Cleans up clang warning:
sound/pci/echoaudio/echoaudio.c:740:20: warning: Value stored to 'pipe'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the commit 1ba8f9d308 ("ALSA: hda: Add a power_save
blacklist"), we changed the default value of power_save option to -1
for processing the power-save blacklist.
Unfortunately, this seems breaking user-space applications that
actually read the power_save parameter value via sysfs and judge /
adjust the power-saving status. They see the value -1 as if the
power-save is turned off, although the actual value is taken from
CONFIG_SND_HDA_POWER_SAVE_DEFAULT and it can be a positive.
So, overall, passing -1 there was no good idea. Let's partially
revert it -- at least for power_save option default value is restored
again to CONFIG_SND_HDA_POWER_SAVE_DEFAULT. Meanwhile, in this patch,
we keep the blacklist behavior and make is adjustable via the new
option, pm_blacklist.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199073
Fixes: 1ba8f9d308 ("ALSA: hda: Add a power_save blacklist")
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_pcm_oss_get_formats() has an obvious use-after-free around
snd_mask_test() calls, as spotted by syzbot. The passed format_mask
argument is a pointer to the hw_params object that is freed before the
loop. What a surprise that it has been present since the original
code of decades ago...
Reported-by: syzbot+4090700a4f13fccaf648@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When releasing a client, we need to clear the clienttab[] entry at
first, then call snd_seq_queue_client_leave(). Otherwise, the
in-flight cell in the queue might be picked up by the timer interrupt
via snd_seq_check_queue() before calling snd_seq_queue_client_leave(),
and it's delivered to another queue while the client is clearing
queues. This may eventually result in an uncleared cell remaining in
a queue, and the later snd_seq_pool_delete() may need to wait for a
long time until the event gets really processed.
By moving the clienttab[] clearance at the beginning of release, any
event delivery of a cell belonging to this client will fail at a later
point, since snd_seq_client_ptr() returns NULL. Thus the cell that
was picked up by the timer interrupt will be returned immediately
without further delivery, and the long stall of snd_seq_delete_pool()
can be avoided, too.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although we've covered the races between concurrent write() and
ioctl() in the previous patch series, there is still a possible UAF in
the following scenario:
A: user client closed B: timer irq
-> snd_seq_release() -> snd_seq_timer_interrupt()
-> snd_seq_free_client() -> snd_seq_check_queue()
-> cell = snd_seq_prioq_cell_peek()
-> snd_seq_prioq_leave()
.... removing all cells
-> snd_seq_pool_done()
.... vfree()
-> snd_seq_compare_tick_time(cell)
... Oops
So the problem is that a cell is peeked and accessed without any
protection until it's retrieved from the queue again via
snd_seq_prioq_cell_out().
This patch tries to address it, also cleans up the code by a slight
refactoring. snd_seq_prioq_cell_out() now receives an extra pointer
argument. When it's non-NULL, the function checks the event timestamp
with the given pointer. The caller needs to pass the right reference
either to snd_seq_tick or snd_seq_realtime depending on the event
timestamp type.
A good news is that the above change allows us to remove the
snd_seq_prioq_cell_peek(), too, thus the patch actually reduces the
code size.
Reviewed-by: Nicolai Stange <nstange@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a need to use DA7219 as DAI clock master for other codecs
within a system, which means that the DAI clocks are required to
remain, regardless of whether the codec is actually running
playback/capture. To be able to expose control of the DAI clocking
the common clock framework has been employed.
The current implementation adds a simple clock gate for enabling
and disabling the DAI clocks, with no rate control supported
(this is still handled through standard hw_params() functions as
before). If DT is enabled then the clock is added to the OF
providers list, otherwise a clkdev lookup is used.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support for UniPhier AIO sound driver
which is included in UniPhier PXs2 SoCs.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As per design, non-circular dma also need to be
stopped explicitly for both playback and capture
scenarios.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Moved 16bit resolution condition check for stoney platform
to acp_hw_params.Depending upon substream required register
value need to be programmed rather than enabling 16bit resolution
support all time in acp init.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds missing initialisation for HP 2013 UltraSlim Dock
Line-In/Out PINs and activates keyboard mute/micmute leds
for HP ProBook 640 G2
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds missing initialisation for HP 2013 UltraSlim Dock
Line-In/Out PINs and activates keyboard mute/micmute leds
for HP EliteBook 820 G3
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Odroid boards are manufactured by Hardkernel, not Samsung. New compatible
string entries are added, with "hardkernel," instead of "samsung," vendor
prefix. Support for the old compatible strings is going to be removed after
some time.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The pointer res is being initialized with a value that is never read
and re-assigned immediately after, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
sound/soc/bcm/cygnus-ssp.c:1284:19: warning: Value stored to 'res'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
One version of Lenovo Thinkpad T570 did not use ALC298
(like other Kaby Lake devices). Instead it uses ALC292.
In order to make the Lenovo dock working with that codec
the dock quirk for ALC292 will be used.
Signed-off-by: Dennis Wassenberg <dennis.wassenberg@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the previous two fixes for the write / ioctl races:
ALSA: seq: Don't allow resizing pool in use
ALSA: seq: More protection for concurrent write and ioctl races
the cells aren't any longer in queues at the point calling
snd_seq_pool_done() in snd_seq_ioctl_set_client_pool(). Hence the
function call snd_seq_queue_client_leave_cells() can be dropped safely
from there.
Suggested-by: Nicolai Stange <nstange@suse.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch is an attempt for further hardening against races between
the concurrent write and ioctls. The previous fix d15d662e89
("ALSA: seq: Fix racy pool initializations") covered the race of the
pool initialization at writer and the pool resize ioctl by the
client->ioctl_mutex (CVE-2018-1000004). However, basically this mutex
should be applied more widely to the whole write operation for
avoiding the unexpected pool operations by another thread.
The only change outside snd_seq_write() is the additional mutex
argument to helper functions, so that we can unlock / relock the given
mutex temporarily during schedule() call for blocking write.
Fixes: d15d662e89 ("ALSA: seq: Fix racy pool initializations")
Reported-by: 范龙飞 <long7573@126.com>
Reported-by: Nicolai Stange <nstange@suse.de>
Reviewed-and-tested-by: Nicolai Stange <nstange@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
None of aio-compress.c depends on the syscon header.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is a fix for a (sort of) fallout in the recent commit
d15d662e89 ("ALSA: seq: Fix racy pool initializations") for
CVE-2018-1000004.
As the pool resize deletes the existing cells, it may lead to a race
when another thread is writing concurrently, eventually resulting a
UAF.
A simple workaround is not to allow the pool resizing when the pool is
in use. It's an invalid behavior in anyway.
Fixes: d15d662e89 ("ALSA: seq: Fix racy pool initializations")
Reported-by: 范龙飞 <long7573@126.com>
Reported-by: Nicolai Stange <nstange@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use kzalloc() instead of kmalloc() so that we don't need to rely fully
on the slave get() callback to clear the control value that might be
copied to user-space.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In slave_update() of vmaster code ignores the error from the slave
get() callback and copies the values. It's not only about the missing
error code but also that this may potentially lead to a leak of
uninitialized variables when the slave get() don't clear them.
This patch fixes slave_update() not to copy the potentially
uninitialized values when an error is returned from the slave get()
callback, and to propagate the error value properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the BYT_RT5651_MCLK_EN quirk is set, we disable the MCLK from
byt_rt5651_init(), we need to select the RCCLK as sysclk before doing this
to make sure that jack-detect works directly after boot.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Change the default quirk settings to enable jack-detect, analog mics.
The old default input mapping of DMIC for non Bay Trail CR devices seems
like a poor default as I'm not aware of any Intel SST + rt5651 using
devices with a DMIC.
All Cherry Trail devices using the bytcr_rt5651 machine driver seem to be
modelled after BYT-CR devices, And the only non CR Bay Trail devices with
a rt5651 codec I'm aware of are the Minnow boards for which we already have
board specific quirks. So it seems better to me to use the BYT-CR defaults
everywhere.
This e.g. makes the Chuwi Hi8 Pro (CWI513) work ootb without needing a
quirk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a quirk setting up jack-detect and input routing for the
VIOS LTH17 laptop.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Despite its name being prefixed with bytcr, before this commit the
bytcr_rt5651 machine driver could not work with Bay Trail CR boards,
as those only have SSP0 and it only supported SSP0-AIF1 setups.
This commit adds support for this, autodetecting AIF1 vs AIF2 based on
BIOS tables.
While at it also add support for SSP2-AIF2 setups, as that requires only
minimal extra code on top of the code adding SSP0-AIF1 / SSP0-AIF2 support.
Note this code is all copy-pasted from bytcr_rt5640.c. I've looked into
merging the 2 machine drivers into 1 to avoid copy-pasting, but there are
enough subtile differences to make this hard *and* with all the quirks the
machine driver already is full with if (variant-foo) then ... else ...
constructs adding more of these is going to make the code unreadable.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a new IN2_HS_IN3 input map and add a quirk for the input mapping and
jack-detect source for the Chuwi Vi8 Plus tablet, which uses this new map.
Note the Chuwi Vi8 Plus lists an extra GPIO in its codecs ACPI resources
which needs to be driven high to enable the external speaker amplifier,
this is not supported yet and will be fixed in a future patch.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All the mappings are named for where the internal mic is routed and in that
sense the newly added in3_map really is the same as in1_map, what makes it
different is that it maps the headset mic at IN3 rather then at IN2.
Rename in3_map to in1_hs_in3_map to better reflect what it actually does.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Drop the snd_soc_dai_set_bclk_ratio() call, the rt5651 dai does not have a
set_bclk_ratio() op, so it is a nop (and returns -EINVAL).
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When platform_clock_control() first selects PLL1 as sysclk the PLL_CTRL
registers have not been setup yet and we effectively have an invalid clock
configuration until byt_rt5651_aif1_hw_params() gets called.
Add a new byt_rt5651_prepare_and_enable_pll1() helper and use that from
both platform_clock_control() and byt_rt5651_aif1_hw_params() to fix this.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for setting the micbias OVCD limits device-properties through
quirks.
And set the limits for this to 2000uA with a scale-factor of 0.75 for the
KIANO SlimNote 14.2 device, which is the only device on which
jack-detection is currently enabled.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only create the jack if we have a valid jack-detect source and properly
check the snd_soc_component_set_jack() return value.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Before this commit it was possible to set the DMIC_EN quirk in the machine
driver, but it would never be passed to the codec driver so it was a nop.
This commit adds code to actually pass the quirk to the codec driver.
Since the DMIC_EN quirk was ignored before, this commit removes it from
the default quirk settings, to avoid this causing an unexpected functional
change. If we really want the DMIC_EN behavior anywhere it should be
specifically enabled by follow up commits.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit add support for a new BYT_RT5651_JDSRC quirk, sets this
quirk for the KIANO SlimNote 14.2 laptop and uses the new "realtek,
jack-detect-source" property to pass this info to the codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If we cannot find the codec ACPI-dev, then the snd-soc-core will not be
able to find the codec either and snd_soc_register_card() will just keep
exiting with -EPROBE_DEFER, filling the log with errors each time the
probe gets retried.
Instead simply log an error from the machine driver and exit with -ENODEV.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We get the insertion event before the jack is fully inserted at which point
the second ring on a TRRS connector may short the 2nd ring and sleeve
contacts. Testing has shown that this short-circuit may happen as late
as 500ms after the insertion event, but it never lasts longer then 300ms.
This commit changes the detection algorithm to require 5 identical OVCD
values in a row at 100 ms intervals to fix the jack-type sometimes getting
mis-detected.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add rt5651_jack_inserted() helper to get the jack-detect switch status,
This is a preparation patch for rewriting the jack type-detection to
make it more reliable.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When using RCCLK instead of MCLK / PLL1 the OVCD status often gets stuck
at its last value, which breaks jack-type detection.
This commit fixes this by force-enabling the platform clock when doing
jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When the mic-gnd contacts are short-circuited by a headphones plug, the
hardware periodically retries if it can apply the bias-current leading to
the OVCD status flip-flopping 1-0-1 with it being 0 about 10% of the time.
This commit enables the sticky bit for the OVCD status to deal with this.
This commit also introduces 2 helper functions to deal with the OVCD
status bit, this may seem a bit overkill now, but these will also be
used in future patches.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect if
an inserted jack is a headset or headphones (mic shorted to ground).
The threshold for at which current the OVCD triggers on the rt5651 is not
only controlled by setting the absolute current limit, but also by setting
a scale factor which applies to the limit. Testing has shown that we need
to set both (depending on the board).
This commit adds support for the sofar unused OVCD scale-factor register
and adds support for specifying non-default values for it through the
"realtek,over-current-scale-factor" device-property.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVer-Current-Detection (OVCD) for the micbias current is used to detect
if an inserted jack is a headset or headphones (mic shorted to ground).
Some boards may need different values for the OVCD current threshold
because of a resistor on the board in serial with or parallel to the
jack mic contact.
This commit adds support for configuring the OCVD current threshold
through the "realtek,over-current-threshold-microamp" device-property.
Note this commit changes the default value from 600uA to 2000uA,
because testing has shown 600uA to be a poor default.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Configure the jack-detect source through a device-property which can be
set by code outside of the codec driver. Rather then putting platform
specific DMI quirks inside the generic codec driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The idea behind exporting rt5651_apply_properties(), was for it to be used
on platforms where the platform code may need to add device-properties,
rather then relying only on properties set by the firmware. The platform
code could then call rt5651_apply_properties() after adding properties to
make sure that the codec driver was aware of the new properties.
But this is not necessary, as long as we do all property parsing from
the codec component-driver's probe function (or later) then the machine
driver can attach properties before calling snd_soc_register_card and
calling rt5651_apply_properties() for ordering reasons is not necessary.
This commit makes rt5651_apply_properties() private and adds 2 comments
documenting that all property parsing must be done from the codec
component-driver's probe function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dock line-out pin (NID 0x17 of ALC3254 codec) on Dell Precision
7520 may route to three different DACs, 0x02, 0x03 and 0x06. The
first two DACS have the volume amp controls while the last one
doesn't. And unfortunately, the auto-parser assigns this pin to DAC3,
resulting in the non-working volume control for the line out.
Fix it by disabling the routing to DAC3 on the corresponding pin.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=199029
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal mic boost on the T480 is too high. Fix this by applying the
ALC269_FIXUP_LIMIT_INT_MIC_BOOST fixup to the machine to limit the gain.
Signed-off-by: Benjamin Berg <bberg@redhat.com>
Tested-by: Benjamin Berg <bberg@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This platform was only one phone Jack.
Add dummy lineout verb to fix automute mode disable.
This just the workaround.
[ More background information:
since the platform has only a headphone jack without speaker, the
driver doesn't create the auto-mute control. Meanwhile we do update
the headset mode via the automute hook in the driver, thus with this
setup, the headset won't be updated any longer.
By adding a dummy line-out pin here, the auto-mute is added by the
driver, and the headset update is triggered properly.
Note that this is different from the other
ALC274_FIXUP_DELL_AIO_LINEOUT_VERB, which has the real line-out pin,
while this quirk adds a dummy line-out pin. -- tiwai ]
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Driver probe function has no use and can be deleted.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the error: passing argument 1 of 'nau8824_enable_jack_detect'
from incompatible pointer type
nau8824_enable_jack_detect(codec, jack);
^~~~~
Which expects 'struct snd_soc_component *' but argument is of type
'struct snd_soc_codec *'
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With the alc289, the Pin 0x1b is Headphone-Mic, so we should assign
ALC269_FIXUP_DELL4_MIC_NO_PRESENCE rather than
ALC225_FIXUP_DELL1_MIC_NO_PRESENCE to it. And this change is suggested
by Kailang of Realtek and is verified on the machine.
Fixes: 3f2f7c553d ("ALSA: hda - Fix headset mic detection problem for two Dell machines")
Cc: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Module id is a property of firmware manifest and can vary across
platforms. So use the uuid to find module id dynamically for bind
params like kpb post bind params.
Signed-off-by: Sriram Periyasamy <sriramx.periyasamy@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Create BE DAI link for WoV and accordingly update the DAPM machine map
Signed-off-by: Pawse, GuruprasadX <guruprasadx.pawse@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently DMIC capture and WoV usecase uses same BE DAI but operate at
different sampling rates, this results in config mismatch for WoV when
DMIC is already running in parallel.
DMIC has two slots which can operate with some constraints, so add BE
DAI for DMICvoice pin which can used for WoV usecases to capture 4ch,
16KHz, 16bit data.
Signed-off-by: Pawse, GuruprasadX <guruprasadx.pawse@intel.com>
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The current check is not effective when all the widgets of a card are
involved since other widgets also can be of same type. So, make widget
type check more stringent by checking dev pointer additionally.
Signed-off-by: Guneshwor Singh <guneshwor.o.singh@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With gcc-4.1.2, if CONFIG_SND_SOC_RT5514_SPI is not set:
sound/soc/codecs/rt5514.c: In function ‘rt5514_dsp_voice_wake_up_put’:
sound/soc/codecs/rt5514.c:363: warning: ‘buf[0]’ is used uninitialized in this function
sound/soc/codecs/rt5514.c:363: warning: ‘buf[1]’ is used uninitialized in this function
sound/soc/codecs/rt5514.c:363: warning: ‘buf[2]’ is used uninitialized in this function
sound/soc/codecs/rt5514.c:363: warning: ‘buf[3]’ is used uninitialized in this function
Fix this by initializing the buffer with zeroes, to avoid random bits
being written to the calibration register later.
Fixes: fc9cab0583 ("ASoC: rt5514: The DSP clock can be calibrated by the other clock source")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5514_dsp_voice_wake_up_put() passes "(u8 *)&buf" to
rt5514_spi_burst_read(), where the cast is needed to silence a compiler
warning:
sound/soc/codecs/rt5514.c: In function ‘rt5514_dsp_voice_wake_up_put’:
sound/soc/codecs/rt5514.c:357: warning: passing argument 2 of ‘rt5514_spi_burst_read’ from incompatible pointer type
However, as the variable is declared as an array ("u8 buf[8]"), the
function should just pass "buf" instead.
Fixes: fc9cab0583 ("ASoC: rt5514: The DSP clock can be calibrated by the other clock source")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
OVCD is not only useful for jack-type detection, but is also useful
to protect against over-current faults in general, so always keep
OVCD enabled, instead of only enabling it for jack-type detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Only configure OVCD once at set_jack time, rather then configuring
it on every jack-insertion event and switch to using bit field defines
instead of hardcoding a magic value.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
To determine if a plugged in jack is a headset (speakers + mic) or
headphones (mic contact shorted to ground) we use the micbias1 OVer Current
Detect (OVCD) functionality.
For this to work we need to have a micbias current to actually cause an
overcurrent condition when headphones are plugged in, so jack-type
detection requires both the LDO and micbias1 supplies to be on.
Before this commit there were 2 issues with the handling of this:
1) The LDO supply was force-enabled twice and never disabled again even
though it only needs to be forced on when doing jack-type detection
2) micbias1 was not force-enabled, and thus may be off when doing jack-type
detection
This commit fixes both by force-enabling the LDO and micbias1 supplies
before checking for an overcurrent condition and disabling them afterwards.
Note that both supplies will still get turned on normally (and OVCD will
protect against overcurrent) when the micbias1 is enabled normally because
the user has activated a sound stream recording from the mic.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the "JD power" dapm supply which gets force-enabled once when
using jack-detect and never gets disabled again.
Since the PWR_JD_M bit simply needs to be always on when using jack-detect
there is no need to have it tracked by dapm, instead we can simply set it
to 1 once when initializing the jack-detection.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that rt5651_set_bias_level(BIAS_OFF) no longer modifies the LDO
voltage selection bits, there is no need to set them each time we move
to standby. Instead configure them once at component-probe() time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the setup of the PWR_ANLG1 reg which was done directly before
calling snd_soc_component_force_bias_level(SND_SOC_BIAS_OFF), as the
latter will override any settings done to PWR_ANLG1 immediately anyways.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, including the jack-detect and PLL power bits. When jack-detection
support was introduced a special case for jack-detect was added which
hard-codes a register value to keep both on.
This commit removes the jack-detect special case, instead simply leaving
these bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The PWR_ANLG1 reg not only contains various power on/off bits, it also
contains 2 bits which select if the LDO generates 1.0, 1.1 or 1.2V. Note
there is a separate on/off bit for the LDO.
rt5651_set_bias_level(BIAS_OFF) used to unconditionally clear the entire
register, when jack-detection support was introduced a special case for
jack-detect was added which hard-codes a register value to keep the LDO
voltage at 1.2 volt.
This commit removes the jack-detect special case, instead simply always
leaving the LDO voltage control bits as is on BIAS_OFF.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rt5651_set_bias_level() function was turning everything off at
SND_SOC_BIAS_STANDBY, rather then at SND_SOC_BIAS_OFF, requiring the bias-
level to be raised to SND_SOC_BIAS_PREPARE before turning anything on.
This is not how the bias-levels are supposed to work, this commit fixes
this by turning everything off at the SND_SOC_BIAS_OFF level and enabling
the pwr-bits needed for minimum functionality at SND_SOC_BIAS_STANDBY.
This fixes the minimum set of pwr-bits not getting enabled when
force-enabling some dapm-supplies (e.g. for jack type detection),
which raises the bias-level to standby.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
is_sys_clk_from_pll() is used as a snd_soc_dapm_route.connected callback,
checking RT5651_GBL_CLK to determine if the sys-clk is PLL1 and thus the
PWR_PLL bit in reg PWR_ANLG2 must be set.
RT5651_GBL_CLK is changed by rt5651_set_dai_sysclk(), which gets called by
the pre_pmu / post_pmd functions of the "Platform Clock" dapm-supply.
This creates an ordering issue, during a dapm transition first all
connected() callbacks are called to build a list of supplies to enable
and then the complete list is walked to enable the supplies. Since the
connected() check happens before enabling any supplies,
is_sys_clk_from_pll() ends up deciding if the PWR_PLL bit should be set
based on the state the "Platform Clock" supply had *before* the transition.
This sometimes results in PWR_PLL being off, even though *after* the
transition PLL1 is configured as sys-clk.
This commit removes is_sys_clk_from_pll() instead simply setting / clearing
PWR_PLL in rt5651_set_dai_sysclk() based on the selected sys-clk, which
fixes this and as a bonus results in a nice cleanup.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an error message within devm_ioremap_resource already,
so remove the redundant dev_err() call.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codes is stereo only with playback and capture streams bind
to the same rate.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tell user what are clock rate limits and reindent log messages.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the applying of the differential input and dmic properties to a new
rt5651_apply_properties() helper function. This new function can be called
by platform code which attaches properties after probe() has run to apply
these new properties.
Note this also moves the time when we apply these properties for DT
platforms from i2c-probe to snd-component-probe time, this should not
result in any functional difference.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the standard component set_jack callback instead of defining a codec
private API for this.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move 2 functions higher up in rt5651.c, this is a preparation patch
to avoid needing forward declarations when moving over from a codec
private function to the standard snd_soc_component_set_jack().
This commit purely moves these 2 functions up, not a single line is
changed.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move all jack-detect initialization to rt5651_set_jack_detect. The main
reason to do this is so that platform code can setup jack-detect properties
after the device has been probed, which unfortunately is necessary on some
platforms.
This has 2 additional advantages:
1) Grouping all jack-detect init together makes it easier to follow what
is happening and results in a small reduction in the number of loc.
2) Before we would register the irq handler before rt5651->hp_jack was
assigned, leading to a potential NULL deref if the jack_detect work runs
before the machine driver has called set_jack.
Tested-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There are no in tree users of platform-data for the rt5651 codec driver,
so lets remove support for it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Create sound card with NAU88L24 codec in Intel Cherryview-based platforms,
Cherrytrail and Braswell.
Signed-off-by: John Hsu <KCHSU0@nuvoton.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
rt5663 requires mclk/sclk early to synchronize its internal clocks.
Enable these clocks early.
Signed-off-by: Naveen Manohar <naveen.m@intel.com>
Signed-off-by: Kevin Cheng <kevin.cheng@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Bay Trail SST-DSP firmware version looses track of all streams over a
suspend/resume, failing any attempts to resume and/or free streams, with
a SST_ERR_INVALID_STREAM_ID error.
This commit adds support for free-ing the streams on suspend and
re-allocating them on resume, fixing suspend/resume issues on devices
using this firmware version.
This new behavior gets triggered by a new flag in sst_platform_info which
only gets set on Bay Trail platforms.
This has been tested on the following devices:
-Asus T100TA, Bay Trail + ALC5642 codec
-Ployer MOMO7W, Bay Trail CR + ALC5652 codec
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Move the struct snd_sst_alloc_mrfld alloc parameters from the stack
into struct stream_info and add a new sst_realloc_stream() function which
can re-alloc a stream with the same parameters as before.
This is a preparation patch for fixing suspend/resume issues with some
SST / DSP firmware versions.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
STREAM_DECODE is completely unused, status == STREAM_RESET was checked
for, but never set, remove both.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
sst_init_stream() has only one caller and all its function arguments are
unused. Inline it on the one call site and remove it.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove the unused ops and str_id members from the stream_info struct.
While at it also remove some kernel-doc comments for members which have
already been removed in the past.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The value returned by sst_prepare_and_post_msg() is a negated SST_ERR_*
value, so we must check for -SST_ERR_INVALID_STREAM_ID. Note that
sst_pause_resume() already has the correct check.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Replace unsafe usages of strcpy() to copy the name
argument into the sid.name buffer with strlcpy()
to guard against possible buffer overflows.
Signed-off-by: Joey Pabalinas <joeypabalinas@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Normal 512-byte get/set of a TLV isn't supported but we were
registering the normal get/set anyway and relying on omitting
the SNDRV_CTL_ELEM_ACCESS_[READ|WRITE] flags to prevent them
being called.
Trouble is if this gets broken in the core ALSA code - as it has
been since at least 4.14 - the standard get/set can be called
unexpectedly and corrupt memory.
There's no point providing functions that won't be called and
it's a trivial change. The benefit is that if the ALSA core gets
broken again we get a big fat immediate NULL dereference instead
of a memory corruption timebomb.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When LPE audio driver gets some error at probing, it may lead to a
crash because of canceling the pending work in hdmi_lpe_audio_free(),
since some of ports might be still not initialized.
For assuring the proper free of each port, initialize all ports at the
beginning of the probe.
Fixes: b4eb0d522f ("ALSA: x86: Split snd_intelhad into card and PCM specific structures")
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit change for supporting the multiple ports moved involved
some code shuffling, and there the initializations of spinlock and
mutex in snd_intelhad object were dropped mistakenly.
This patch adds the missing initializations again for each port.
Fixes: b4eb0d522f ("ALSA: x86: Split snd_intelhad into card and PCM specific structures")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Remove a bunch of trailing whitespace errors. They are
fairly annoying if you have your editor set to strip trailing
whitespace because you find you've introduced more changes
than you were trying to make.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch "ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE
operations" introduced a potential for kernel memory corruption due
to an incorrect if statement allowing non-readable controls to fall
through and call the get function. For TLV controls a driver can omit
SNDRV_CTL_ELEM_ACCESS_READ to ensure that only the TLV get function
can be called. Instead the normal get() can be invoked unexpectedly
and as the driver expects that this will only be called for controls
<= 512 bytes, potentially try to copy >512 bytes into the 512 byte
return array, so corrupting kernel memory.
The problem is an attempt to refactor the snd_ctl_elem_read function
to invert the logic so that it conditionally aborted if the control
is unreadable instead of conditionally executing. But the if statement
wasn't inverted correctly.
The correct inversion of
if (a && !b)
is
if (!a || b)
Fixes: becf9e5d55 ("ALSA: control: code refactoring for ELEM_READ/ELEM_WRITE operations")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Motorola CPCAP is a PMIC with audio functionality, that can be
found on Motorola Droid 4 and probably a few other phones from
Motorola's Droid series.
The driver has been written from scratch using Motorola's Android
driver, register dumps from running Android and datasheet for NXP
MC13783UG (which is similar to Motorola CPCAP, but not the same).
The chip provides two audio interfaces, that can be muxed to two
different audio codecs. One provides support for stereo output
(named StDAC or HiFi), while the other only provides mono output
(named Voice). Only the Voice codec provides a Capture interface.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds support of the ROHM BD28623MUV
Class D speaker amplifier for Flat-panel TVs.
This IC delivers an output power of 20W + 20W.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
fsl-asoc-card machine driver also handles wm8962, so there is
really no need for keeping the dedicated imx-wm8962 driver anymore.
Remove the imx-wm8962 machine driver.
Suggested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The show() method should use scnprintf() not snprintf() because snprintf()
may returns a value that exceeds its second argument.
Signed-off-by: Jaejoong Kim <climbbb.kim@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit f91b1e73cc.
As explained by Lars-Peter Clausen:
"This creates a resource leak. dmaengine_pcm_request_chan_of() requests
bothtransmit and receive channels. It might return with an error if one
of them fails, but the other one succeeded. In this case we need to call
dmaengine_pcm_release_chan() to free the requested channel"
So revert the commit.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We've added a quirk to enable the recent Lenovo dock support, where it
overwrites the pin configs of NID 0x17 and 19, not only updating the
pin config cache. It works right after the boot, but the problem is
that the pin configs are occasionally cleared when the machine goes to
PM. Meanwhile the quirk writes the pin configs only at the pre-probe,
so this won't be applied any longer.
For addressing that issue, this patch moves the code to overwrite the
pin configs into HDA_FIXUP_ACT_INIT section so that it's always
applied at both probe and resume time.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195161
Fixes: 61fcf8ece9 ("ALSA: hda/realtek - Enable Thinkpad Dock device for ALC298 platform")
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support of S/PDIF iec60958 playback on STM32 SAI.
Signed-off-by: olivier moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow dmaengine client to optionally register a processing callback.
This callback is intended to apply processing
on samples in buffer copied from/to user space, before/after DMA transfer.
Signed-off-by: Olivier Moysan <olivier.moysan@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the following sparse warnings are observed:
sound/soc/soc-generic-dmaengine-pcm.c:185:34: warning: restricted snd_pcm_format_t degrades to integer
sound/soc/soc-generic-dmaengine-pcm.c:186:66: warning: incorrect type in argument 1 (different base types)
sound/soc/soc-generic-dmaengine-pcm.c:186:66: expected restricted snd_pcm_format_t [usertype] format
sound/soc/soc-generic-dmaengine-pcm.c:186:66: got int [signed] [assigned] i
Fix it by changing the loop variable to be of 'snd_pcm_format_t'.
Also introduce a SNDRV_PCM_FORMAT_FIRST label, which corresponds to the
first member (index 0) of the snd_pcm_format_t formats.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When dmaengine_pcm_request_chan_of() fails it should release
the previously acquired resources, which in this case is to
call kfree(pcm), so jump to the correct point in the error
path.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clear the buffer data structure on each trigger start such that the
buffer is in a sensible state even if the DSP itself didn't restart.
This is necessary to support voice control streams which can trigger
multiple times without reloading the firmware.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I2S's RX slot number of SUN8I should be shifted 4 bit to left.
Fixes: 7d2993811a ("ASoC: sun4i-i2s: Add support for H3")
Signed-off-by: Yong Deng <yong.deng@magewell.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Bit pattern SNDRV_PCM_FMTBIT_S24_LE is being bit-wise or'd twice; remove
the redundant 2nd SNDRV_PCM_FMTBIT_S24_LE
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Bit pattern USP_RXFIFO_THD_INT is being bit-wise or'd twice;
remove the redundant 2nd USP_RXFIFO_THD_INT
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes settings for ports with SRC. These ports need to
set the fixed audio rate and clock. If not, the SRC outputs broken
sound.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The capture interface doesn't work and the playback interface only
supports 48 kHz sampling rate even though it advertises more rates.
Signed-off-by: Erik Veijola <erik.veijola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some boards setting power_save to a non 0 value leads to clicking /
popping sounds when ever we enter/leave powersaving mode. Ideally we would
figure out how to avoid these sounds, but that is not always feasible.
This commit adds a blacklist for devices where powersaving is known to
cause problems and disables it on these devices.
Note I tried to put this blacklist in userspace first:
https://github.com/systemd/systemd/pull/8128
But the systemd maintainers rightfully pointed out that it would be
impossible to then later remove entries once we actually find a way to
make power-saving work on listed boards without issues. Having this list
in the kernel will allow removal of the blacklist entry in the same commit
which fixes the clicks / plops.
The blacklist only applies to the default power_save module-option value,
if a user explicitly sets the module-option then the blacklist is not
used.
[ added an ifdef CONFIG_PM for the build error -- tiwai]
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1525104
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=198611
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
After the conversion from platform to component the following warnings
are seen:
fsl-ssi-dai 2028000.ssi: ASoC: Failed to create component debugfs
directory
fsl-spdif-dai 2004000.spdif: ASoC: Failed to create component debugfs
directory
As explained by Mark Brown:
"It's a legit warning - we shouldn't really be creating two components
for the same device. However this is a bit of a corner case as it's the
dmaengine platform driver which is kind of a virtual device, it's not
really the device that we use with DMA that's being represented but
rather the link between that and the DMA controller."
Disambiguate the DMA component name by adding a "dma" debugfs_prefix
entry.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch changes lisence comment style from C to C++.
And use SPDX instead of boiler plate of GPLv2, as same as
other audio codec drivers.
Signed-off-by: Katsuhiro Suzuki <suzuki.katsuhiro@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The recent support for the multiple PCM devices allowed user to use
multiple HDMI/DP outputs, but at the same time, the PCM stream
assignment has been changed, too. Due to that, the former PCM#0
(there was only one stream in the past) is likely assigned to a
different one (e.g. PCM#2), and it ends up with the regression when
user sticks with the fixed configuration using the device#0.
Although the multiple monitor support shouldn't matter when user
deploys the backend like PulseAudio that checks the jack detection
state, the behavior change isn't always acceptable for some users.
As a mitigation, this patch introduces an option to switch the
behavior back to the old-good-days: when the new option,
single_port=1, is passed, the driver creates only a single PCM device,
and it's assigned to the first connected one, like the earlier
versions did. The option is turned off as default still to support
the multiple monitors.
Fixes: 8a2d6ae1f7 ("ALSA: x86: Register multiple PCM devices for the LPE audio card")
Reported-and-tested-by: Hubert Mantel <mantel@metadox.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since ssi->streams is being updated along with SCR register and
its SSIEN bit, it's simpler to use it instead.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleans up probe() function by moving all Device Tree
related code into a separate function. It allows the probe() to
be Device Tree independent. This will be very useful for future
integration of imx-ssi driver which has similar functionalities
while exists only because it supports non-DT cases.
This patch also moves symmetric_channels of AC97 from the probe
to the structure snd_soc_dai_driver for simplification.
Additionally, since PowerPC and AC97 use the same pdev pointer
to register a platform device, this patch also unifies related
code.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Using symmetric_rates in the cpu_dai_drv is a bit implicit,
so this patch adds a bool synchronous instead.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The _fsl_ssi_set_dai_fmt() is a helper function being called from
fsl_ssi_set_dai_fmt() as an ASoC operation and fsl_ssi_hw_init()
mainly for AC97 format initialization.
This patch cleans the _fsl_ssi_set_dai_fmt() in following ways:
* Removing *dev pointer in the parameters as it's included in the
*ssi pointer of struct fsl_ssi.
* Using regmap_update_bits() instead of regmap_read() with masking
the value manually.
* Moving baudclk check to the switch-case routine to skip the I2S
master check. And moving SxCCR.DC settings after baudclk check.
* Adding format settings for SND_SOC_DAIFMT_AC97 like others.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
AC97 configures most of registers earlier to start a communication
with CODECs in order to successfully initialize CODEC. Currently,
_fsl_ssi_set_dai_fmt() and fsl_ssi_setup_ac97() are called to get
all SSI registers properly set.
Since now the driver has a fsl_ssi_hw_init() to handle all register
initial settings, this patch moves those register settings of AC97
to the fsl_ssi_hw_init() as well.
Meanwhile it applies _fsl_ssi_set_dai_fmt() call to AC97 only since
other formats would be configured via normal set_dai_fmt() directly.
This patch also adds fsl_ssi_hw_clean() to cleanup control bits for
AC97 in the platform remote() function.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The probe() could handle some one-time configurations since
they will not be changed once being configured.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since there is a helper function, use it to help readability.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
It'd be safer to enable both FIFOs for TX or RX at the same time.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch cleans fsl_ssi_setup_regvals() by following changes:
1) Moving DBG bits to the first lines.
2) Setting SSIE, RE/TE as default and cleaning it for AC97
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The _fsl_ssi_set_dai_fmt() bypasses an undefined format for AC97
mode. However, it's not really necessary if AC97 has its complete
format defined.
So this patch adds a DAIFMT macro of complete format including a
clock direction and polarity.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The trigger() calls fsl_ssi_tx_config() and fsl_ssi_rx_config(),
and both of them jump to fsl_ssi_config(). And fsl_ssi_config()
later calls another fsl_ssi_rxtx_config().
However, the whole routine, especially fsl_ssi_config() function,
is too complicated because of the folowing reasons:
1) It has to handle the concern of the opposite stream.
2) It has to handle cases of offline configurations support.
3) It has to handle enable and disable operations while they're
mostly different.
Since the enable and disable routines have more differences than
TX and RX rountines, this patch simplifies these helper functions
with the following changes:
- Changing to two helper functions of enable and disable instead
of TX and RX.
- Removing fsl_ssi_rxtx_config() by separately integrating it to
two newly introduced enable & disable functions.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The FIFO clear helper function is just one line of code now.
So it could be cleaned up by removing it and calling regmap
directly.
Meanwhile, FIFO clear could be applied to all use cases, not
confined to AC97. So this patch also moves FIFO clear in the
trigger() to fsl_ssi_config() and removes the AC97 check.
Note that SOR register is safe from offline_config HW limit.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The define of fsl_ssi_disable_val is not so clear as it mixes two
steps of calculations together. And those parameter names are also
a bit long to read.
Since it just tries to exclude the shared bits from the regvals of
current stream while the opposite stream is active, it's better to
use something like ssi_excl_shared_bits.
This patch also bisects fsl_ssi_disable_val into two macros of two
corresponding steps and then shortens its parameter names. It also
updates callers in the fsl_ssi_config() accordingly.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking TE and RE bits in SCR register doesn't work for AC97 mode
which enables SSIEN, TE and RE in the fsl_ssi_setup_ac97() that's
called during probe().
So when running into the trigger(), it will always get the result
of both TE and RE being enabled already, even if actually there is
no active stream.
This patch fixes this issue by adding a variable to log the active
streams manually.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch replaces the register read with ssi->i2s_net for
simplification. It also removes masking SSIEN from scr value
since it's handled later by regmap_update_bits() to set this
scr value back.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hw_params() overwrites i2s_net settings for special cases like
mono-channel support, however, it doesn't update ssi->i2s_net as
set_dai_fmt() does.
This patch removes the local i2s_net variable and directly updates
ssi->i2s_net in the hw_params() so that the driver can simply look
up the ssi->i2s_net instead of reading the register.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RX and TX macros were defined implicitly and there was
a potential risk if someone changes their values.
Since they were defined to index the array ssi->regvals[2],
this patch moves these two macros to fsl_ssi.c, closer to
its owner ssi->regvals. And it also puts some comments here
to limit their value within [0, 1].
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Tested-by: Caleb Crome <caleb@crome.org>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Reviewed-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Mark Brown <broonie@kernel.org>
Repair any formatting/style issues that can be fixed without major
code refactoring.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use // for .c and /* for .h files according to:
Documentation/process/license-rules.rst file.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hcp->chmap_info must not be freed up in the hdmi_codec_remove()
function as it leads to kernel crash due ALSA core's
pcm_chmap_ctl_private_free() is trying to free it up again when the card
destroyed via snd_card_free.
Since the driver was converted to devm_snd_soc_register_component() the
whole platform_device.remove can be removed.
Commit cd6111b262 ("ASoC: hdmi-codec: add channel mapping control")
should not have added the kfree(hcp->chmap_info); to the hdmi_codec_remove
function.
[Separate verison of the fix for -next -- broonie]
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hcp->chmap_info must not be freed up in the hdmi_codec_remove()
function as it leads to kernel crash due ALSA core's
pcm_chmap_ctl_private_free() is trying to free it up again when the card
destroyed via snd_card_free.
Commit cd6111b262 ("ASoC: hdmi-codec: add channel mapping control")
should not have added the kfree(hcp->chmap_info); to the hdmi_codec_remove
function.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Jyri Sarha <jsarha@ti.com>
Tested-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The max9759 is a gpio controlled amplifier.
Tested on a Variscite Dart MX6 SoM based custom board.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Modify SPDX comment style to match the rules. Since the original
code had a GPL-2.0 license and SPDX is compatible with GPL-2.0+,
we also modified the MODULE_LICENSE.
Signed-off-by: Cosmin-Gabriel Samoila <cosmin.samoila@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adding ACPI entry id for probing the driver.
Signed-off-by: Akshu Agrawal <akshu.agrawal@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Removed hardcoding in dma descriptor programming api's.
These changes are required to extend the logic to support
dma descriptor programming for multiple i2s controller
instances.
Signed-off-by: Vijendar Mukunda <Vijendar.Mukunda@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Mark Brown <broonie@kernel.org>