When NFP is modelled as a switch we assign phys_port_name to respective
port(representor )s:
vNIC0 - | - PF port (pf%d) MAC/PHY (p%d[s%d]) - |E==
In most cases there is only one vNIC for communication with the switch.
If there is more than one we need to be able to identify them. Use %d
as phys_port_name of the vNICs.
We don't have to pass ID to nfp_net_debugfs_vnic_add() separately any
more.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PCI PFs can host more than one logical endpoint. In NFP terms
this means having more than one vNIC for PCIe PF. The vNICs
are usually corresponding 1:1 to Ethernet ports. In core NIC
we use the legacy idea of vNIC *being* the Ethernet port,
hence netdevs put pX(sY) in their phys_port_name, like Ethernet
ports would. When ASIC ports are fully represented we need to
be able to name different PCIe PF ports, too. Use a scheme
similar to Ethernet ports - pfXsY, for PCIe PF number X,
sub-port Y.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current control firmware does not cater too well to multi-host
applications. There is no way to check which hosts are up or
otherwise negotiate what the state of the external port (the
Ethernet port) should be. Make sure the link is up when driver
loads, and don't take it down when Ethernet port netdev is
closed.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To configure buffering points we need full set of netdevs:
ASIC
user netdev -- | -- PCIe port MAC port -- | --
Configuring egrees qdiscs on user netdev configures standard
Linux TC software qdiscs, configuring PCIe port qdiscs will
provide a way of setting ASIC queuing parameters for PCIe block.
MAC port netdev egress qdiscs correspond to ASIC MAC Traffic
Manager block.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Our previous apps all assumed to use only one eswitch mode (legacy
or switchdev) without the ability to change it. ABM NIC will
want to support the switch so plumb devlink_eswitch_mode_set through.
The devlink_eswitch_mode_set is expected to spawn representors and
potentially devlink ports so it's called under big devlink lock and
pf->lock.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_apps can currently associate their structures with vNICs but
not representors. Add app priv pointer to representors as well.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ABM NIC requires more complex vNIC handling, allocate
per-vNIC structure. Find out RX queue base and PCI PF id.
There will be multiple PFs sharing the same MAC port, therefore
the MAC address assigned to the vNIC must be looked up in the
HWInfo database.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a very rudimentary active buffer management NIC support.
For now it's like a core NIC without SR-IOV support. Next
commits will extend its functionality.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code doesn't enforce length requirements on 32bit accesses
with action NFP_CPP_ACTION_RW to memory units, but if the access
is only aligned to 4 bytes as well we will fall into the explicit
access case and error out. Such accesses are correct, allow them
by lowering the width earlier.
While at it use a switch statement to improve readability.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow app FW to advertise its shared buffer pool information.
Use the per-PF mailbox to configure them from devlink.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When working with devlink-related functionality for locking reasons
it's easier to create a new mailbox per-PCI PF device than try to
use one of the netdev/vNIC mailboxes.
Define new mailbox structure and resolve its symbol during probe.
For forward compatibility allow silent truncation of mailbox command
data.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
nfp_net_pf_rtsym_read_optional() and nfp_net_pf_map_rtsym() are not
really related to networking code. Move them to the PF code and
remove the net from their names. They will soon be needed by code
outside of nfp_net_main.c anyway.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW requests the TLVs in interrupt context. Extracting of the required
data from upper layers and populating of the TLVs require process context.
The patch adds work-queues for processing the tlv requests. It also adds
the implementation for requesting the tlv values from appropriate protocol
driver.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for processing TLV requests/repsonses
from the mfw and upper driver layers respectively. The implementation
reads the requested TLVs from the shared memory, requests the values
from upper layer drivers, populates this info (TLVs) shared memory and
notifies MFW about the TLV values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required management firmware (MFW) interfaces such as
mailbox commands, TLV types etc.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
40GbE Intel Wired LAN Driver Updates 2018-05-22
This series contains updates to i40e only.
Jake provides all the changes in this series starting with making it
consistent in how we approach the bit lock. Fixed the reporting of the
VEB statistics and the queue statistics to always return every queue
even if it is not currently in use. Use WARN_ONCE() so that the first
time we end up with an incorrect size we will dump a stack trace and a
message to help highlight the issue early in testing. Folded the fixed
string prefix into the stat string definition. Instead of using a
separate char *p pointer when copying strings, use the data pointer
directly. Added code comments for several of the statistic functions to
better explain the number and ordering of statistics.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle append for gateway based routes. Dev-only multipath routes will
be handled by a follow on patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since we no longer use i as an array index for the data variable,
replace the use of 'j' with 'i' so that we match the general loop
variable name.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add documentation for the i40e_get_stats_count, i40e_get_stat_strings
and i40e_get_ethtool_stats explaining that the number and ordering of
statistics must remain constant for a given netdevice.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A future patch is going to add a helper function i40e_add_ethtool_stats
that will help lower the amount of boiler plate code in the
i40e_get_ethtool_stats function.
This conversion will take place over many patches, and the helper
function will work by directly updating a reference to the data pointer.
Since this would not work combined with the current method of accessing
data like an array, update all the code that copies stats into the data
buffer to use direct updates to the pointer instead of array accesses.
This will prevent incorrect stat updates for patches in between the
conversion.
Similarly, when copying strings, we used a separate char *p pointer.
Instead, use the data pointer directly as it's already a (u8 *) type
which is the same size.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We always prefix these stats with a fixed string, so just fold this
prefix into the stat string definition. This preparatory work will make
it easier to implement a helper function to copy stats and strings into
the supplied buffers in a future patch.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't really want to use BUG_ON here since that would completely
crash the kernel, thus the reason we commented it out. We *can't* use
BUILD_BUG_ON because at least now (a) the sizes aren't constant (we are
fixing this) and (b) not all compilers are smart enough to understand
that "p - data" is a constant.
Instead, just use a WARN_ONCE so that the first time we end up with an
incorrect size we will dump a stack trace and a message, hopefully
highlighting the issues early in testing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Split the statistic strings and private flags strings into their own
separate functions to aid code readability.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the queue statistics to always return
every queue even if it's not currently in use.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The ethtool API for obtaining device statistics is not intended to allow
runtime changes in the number of statistics reported. It may *appear*
this way, as there is an ability to request the number of stats using
ethtool_get_set_count(). However, it is expected that this must always
return the same value for invocations of the same device.
If we don't satisfy this contract, and allow the number of stats to
change during run time, we could cause invalid memory accesses or report
the stat strings incorrectly. This is because the API for obtaining
stats is to (1) get the size, (2) get the strings and finally (3) get
the stats. Since these are each separate ethtool op commands, it is not
possible to maintain consistency by holding the RTNL lock over the whole
operation. This results in the potential for a race condition to occur
where the size changed between any of the 3 calls.
Avoid this issue by requiring that we always return the same value for
a given device. We can check any values which remain constant for the
life of the device, but must not report different sizes depending on
runtime attributes.
This patch specifically fixes the VEB statistics strings to always be
reported. Other issues will be fixed in future patches.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the same logic to free the skb after clearing the Tx timestamp bit
lock in i40e_ptp_stop as we use in the other locations. It is not as
important here since we are not racing against a future Tx timestamp
request (as we are disabling PTP at this point). However it is good to
be consistent in how we approach the bit lock so that future callers
don't copy the old anti-pattern.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Now that we can compile test this driver on 64-bit hosts, we get some
warnings about how a pointer/address is written/read to/from a register
(sw_token). Fix this by doing the appropriate conversions, we cannot
possibly have the driver work on 64-bit hosts the way the tokens are
managed though, since the registers being written to a 32-bit only.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use %pa which is the correct formatter to print a physical address,
instead of %p which is just a pointer.
Fixes: a6286ee630 ("net: Add TI DaVinci EMAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When building on a 64-bit host we will get the following warning:
drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_add_ch_strings':
drivers/net/ethernet/ti/cpsw.c:1284:19: warning: format '%d' expects
argument of type 'int', but argument 5 has type 'long unsigned int'
[-Wformat=]
"%s DMA chan %d: %s", rx_dir ? "Rx" : "Tx",
~^
%ld
Fix this by using an %ld format and casting to long.
Fixes: e05107e6b7 ("net: ethernet: ti: cpsw: add multi queue support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On 64-bit hosts we will get the following warning:
drivers/net/ethernet/ti/cpts.c: In function 'cpts_overflow_check':
drivers/net/ethernet/ti/cpts.c:297:11: warning: format '%lld' expects
argument of type 'long long int', but argument 3 has type
'__kernel_time_t {aka long int}' [-Wformat=]
pr_debug("cpts overflow check at %lld.%09lu\n", ts.tv_sec,
ts.tv_nsec);
Fix this by using an appropriate casting that works on all bit sizes.
Fixes: a5c79c26e1 ("ptp: cpts: convert to the 64 bit get/set time methods.")
Fixes: 87c0e764d4 ("cpts: introduce time stamping code and a PTP hardware clock.")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we can compile davinci_cpdma.c on 64-bit hosts, we can see that
the format used for printing a size_t type is incorrect, use %zd
accordingly.
Fixes: aeec302104 ("net: ethernet: ti: cpdma: remove used_desc counter")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
immdlen field of FW_ETH_TX_PKT_WR is filled in a wrong way,
we must copy the length of all the cpls encapsulated in fw
work request. In the xmit path we missed adding the length
of CPL_TX_PKT_CORE but we added the length of WR_HDR and it
worked because WR_HDR and CPL_TX_PKT_CORE are of same length.
Add the length of cpl_tx_pkt_core not WR_HDR's. This also
fixes the lso cpl errors for udp tunnels
Fixes: d0a1299c6b ("cxgb4: add support for vxlan segmentation offload")
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A number of entries were not alphabetically sorted, remedy that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simon has noticed a typo in the comment accompaining the BCULR write --
fix it and move the comment before the write (following the style of
the other comments), while at it...
Reported-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All the verbs in the comments to the 'struct sh_eth_cpu_data' declaration
should be in a 3rd person singular, to match the nouns.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The correct name of the EESR bit 8 is TRO (transmit retry over), not RTO.
Note that EESIPR bit 8, TROIP remained correct...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When vf module is loading, the cmd queue initialization should
happen before misc interrupt initialization, otherwise the misc
interrupt handle will cause using uninitialized cmd queue problem.
There is also the same issue when vf module is unloading.
This patch fixes it by adjusting the location of some function.
Fixes: e2cb1dec97 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_ARM_SMMU_V3 is enabled, arm64's dma_ops will replace
arm64_swiotlb_dma_ops with iommu_dma_ops. When releasing contiguous
dma memory, the new ops will call the vunmap function which cannot
be run in interrupt context.
Currently, spin_lock_bh is called before vunmap is executed. This
disables BH and causes the interrupt context to be detected to
generate a kernel panic like below:
[ 2831.573400] kernel BUG at mm/vmalloc.c:1621!
[ 2831.577659] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
...
[ 2831.699907] Process rmmod (pid: 1893, stack limit = 0x0000000055103ee2)
[ 2831.706507] Call trace:
[ 2831.708941] vunmap+0x48/0x50
[ 2831.711897] dma_common_free_remap+0x78/0x88
[ 2831.716155] __iommu_free_attrs+0xa8/0x1c0
[ 2831.720255] hclge_free_cmd_desc+0xc8/0x118 [hclge]
[ 2831.725128] hclge_destroy_cmd_queue+0x34/0x68 [hclge]
[ 2831.730261] hclge_uninit_ae_dev+0x90/0x100 [hclge]
[ 2831.735127] hnae3_unregister_ae_dev+0xb0/0x868 [hnae3]
[ 2831.740345] hns3_remove+0x3c/0x90 [hns3]
[ 2831.744344] pci_device_remove+0x48/0x108
[ 2831.748342] device_release_driver_internal+0x164/0x200
[ 2831.753553] driver_detach+0x4c/0x88
[ 2831.757116] bus_remove_driver+0x60/0xc0
[ 2831.761026] driver_unregister+0x34/0x60
[ 2831.764935] pci_unregister_driver+0x30/0xb0
[ 2831.769197] hns3_exit_module+0x10/0x978 [hns3]
[ 2831.773715] SyS_delete_module+0x1f8/0x248
[ 2831.777799] el0_svc_naked+0x30/0x34
This patch fixes it by using spin_lock instead of spin_lock_bh.
Fixes: 68c0a5c706 ("net: hns3: Add HNS3 IMP(Integrated Mgmt Proc) Cmd Interface Support")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The link status update function is called by timer every second. But
net_stop and net_open may be called with very short intervals. The link
status update function can not detect the link state has changed. It
causes the netdev not running problem.
This patch fixes it by updating the link state in ae_stop function.
Fixes: 46a3df9f97 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does bit of a clean-up by using already defined enums for
certain values in function hclge_is_special_opcode(). Below enums from
have been used as replacements for magic values:
enum hclge_opcode_type{
<snip>
HCLGE_OPC_STATS_64_BIT = 0x0030,
HCLGE_OPC_STATS_32_BIT = 0x0031,
HCLGE_OPC_STATS_MAC = 0x0032,
<snip>
};
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the hns3 driver has been built into kernel and then loaded with
the same driver which built as KLM, it may trigger an error like
below:
[ 20.009555] hns3: Hisilicon Ethernet Network Driver for Hip08 Family - version
[ 20.016789] hns3: Copyright (c) 2017 Huawei Corporation.
[ 20.022100] Error: Driver 'hns3' is already registered, aborting...
[ 23.517397] Unable to handle kernel NULL pointer dereference at virtual address 00000000
...
[ 23.691583] Process insmod (pid: 1982, stack limit = 0x00000000cd5f21cb)
[ 23.698270] Call trace:
[ 23.700705] __list_del_entry_valid+0x2c/0xd8
[ 23.705049] hnae3_unregister_client+0x68/0xa8
[ 23.709487] hns3_init_module+0x98/0x1000 [hns3]
[ 23.714093] do_one_initcall+0x5c/0x170
[ 23.717918] do_init_module+0x64/0x1f4
[ 23.721654] load_module+0x1d14/0x24b0
[ 23.725390] SyS_init_module+0x158/0x208
[ 23.729300] el0_svc_naked+0x30/0x34
This patch fixes it by adding module version info.
Fixes: 38caee9d3e ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the missing initialization of the client list node
in the hnae3_register_client() function.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Removes the goto and directly returns in case of errors as part of the
cleanup.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During the RX leg driver needs to fetch the ethernet header
length from the RX'ed Buffer Descriptor. Currently, proprietary
version hns3_nic_get_headlen is being used to fetch the header
length which uses l234info present in the Buffer Descriptor
which might not be valid for the first Buffer Descriptor if the
packet is spanning across multiple descriptors.
Kernel default eth_get_headlen API does the job correctly.
Fixes: 76ad4f0ee7 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the error reported by Intel's kbuild and fixes a
return value in one of the legs, caught during review of the original
patch sent by kbuild.
Fixes: fdb793670a00 ("net: hns3: Add support of .sriov_configure in HNS3 driver")
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit removed calls to rtl_set_rx_mode(). This is ok for the
standard path if the link is brought up, however it breaks system
resume from suspend. Link comes up but no network traffic.
Meanwhile common code from rtl_hw_start_8169/8101/8168() was moved
to rtl_hw_start(), therefore re-add the call to rtl_set_rx_mode()
there.
Due to adding this call we have to move definition of rtl_hw_start()
after definition of rtl_set_rx_mode().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Fixes: 82d3ff6dd1 ("r8169: remove calls to rtl_set_rx_mode")
Signed-off-by: David S. Miller <davem@davemloft.net>
