After following the call tree of phy_set_max_speed(), it became clear
that this function never returns anything but 0, so we can change its
result type to *void* and drop the result checks from the three drivers
that actually bothered to do it...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for downstream SFP cages for AR8031 and AR8033. This is
primarily intended for fiber modules or direct-attach cables, however
copper modules which work in 1000Base-X mode may also function. Such
modules are allowed with a warning.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously this driver always forced the copper page to be selected,
however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page
needs to be selected. Set the appropriate mode based on the hardware
mode_cfg strap selection.
Enable the appropriate interrupt bits to detect fiber-side link up
or down events.
Update config_aneg and read_status methods to use the appropriate
Clause 37 calls when fiber mode is in use.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fix to select the copper page on AR8031 was being done in the probe
function rather than config_init, so it would not be redone after resume
from suspend. Move this to config_init so it is always redone when
needed.
Fixes: c329e5afb4 ("net: phy: at803x: select correct page on config init")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices
and sfp cages") added code which finds SFP bus DT node even if the node
is disabled with status = "disabled". Because of this, when phylink is
created, it ends with non-null .sfp_bus member, even though the SFP
module is not probed (because the node is disabled).
We need to ignore disabled SFP bus node.
Fixes: ce0aa27ff3 ("sfp: add sfp-bus to bridge between network devices and sfp cages")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: stable@vger.kernel.org # 2203cbf2c8 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bafbdd527d ("phylib: Add device reset GPIO support") added call
to phy_device_reset(phydev) after the put_device() call in phy_detach().
The comment before the put_device() call says that the phydev might go
away with put_device().
Fix potential use-after-free by calling phy_device_reset() before
put_device().
Fixes: bafbdd527d ("phylib: Add device reset GPIO support")
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220119162748.32418-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A problem was encountered with the Bel-Fuse 1GBT-SFP05 SFP module (which
is a 1 Gbps copper module operating in SGMII mode with an internal
BCM54616S PHY device) using the Xilinx AXI Ethernet MAC core, where the
module would work properly on the initial insertion or boot of the
device, but after the device was rebooted, the link would either only
come up at 100 Mbps speeds or go up and down erratically.
I found no meaningful changes in the PHY configuration registers between
the working and non-working boots, but the status registers seemed to
have a lot of error indications set on the SERDES side of the device on
the non-working boot. I suspect the problem is that whatever happens on
the SGMII link when the device is rebooted and the FPGA logic gets
reloaded ends up putting the module's onboard PHY into a bad state.
Since commit 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
the genphy_soft_reset call is not made automatically by the PHY core
unless the callback is explicitly specified in the driver structure. For
most of these Broadcom devices, there is probably a hardware reset that
gets asserted to reset the PHY during boot, however for SFP modules
(where the BCM54616S is commonly found) no such reset line exists, so if
the board keeps the SFP cage powered up across a reboot, it will end up
with no reset occurring during reboots.
Hook up the genphy_soft_reset callback for BCM54616S to ensure that a
PHY reset is performed before the device is initialized. This appears to
fix the issue with erratic operation after a reboot with this SFP
module.
Fixes: 6e2d85ec05 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a setup with KSZ9131 and MACB drivers it happens on suspend path, from
time to time, that the PHY interrupt arrives after PHY and MACB were
suspended (PHY via genphy_suspend(), MACB via macb_suspend()). In this
case the phy_read() at the beginning of kszphy_handle_interrupt() will
fail (as MACB driver is suspended at this time) leading to phy_error()
being called and a stack trace being displayed on console. To solve this
.suspend/.resume functions for all KSZ devices implementing
.handle_interrupt were replaced with kszphy_suspend()/kszphy_resume()
which disable/enable interrupt before/after calling
genphy_suspend()/genphy_resume().
The fix has been adapted for all KSZ devices which implements
.handle_interrupt but it has been tested only on KSZ9131.
Fixes: 59ca4e58b9 ("net: phy: micrel: implement generic .handle_interrupt() callback")
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7cfa9c92d0 ("net: sfp: avoid power switch on address-change
modules") unintetionally changed the semantics for high power modules
without the digital diagnostics monitoring. We repeatedly attempt to
read the power status from the non-existing 0xa2 address in a futile
hope this failure is temporary:
[ 8.856051] sfp sfp-eth3: module NTT 0000000000000000 rev 0000 sn 0000000000000000 dc 160408
[ 8.865843] mvpp2 f4000000.ethernet eth3: switched to inband/1000base-x link mode
[ 8.873469] sfp sfp-eth3: Failed to read EEPROM: -5
[ 8.983251] sfp sfp-eth3: Failed to read EEPROM: -5
[ 9.103250] sfp sfp-eth3: Failed to read EEPROM: -5
We previosuly assumed such modules were powered up in the correct mode,
continuing without further configuration as long as the required power
class was supported by the host.
Restore this behaviour, while preserving the intent of subsequent
patches to avoid the "Address Change Sequence not supported" warning
if we are not going to be accessing the DDM address.
Fixes: 7cfa9c92d0 ("net: sfp: avoid power switch on address-change modules")
Reported-by: 照山周一郎 <teruyama@springboard-inc.jp>
Tested-by: 照山周一郎 <teruyama@springboard-inc.jp>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Existing genphy_loopback() is not applicable for Marvell PHY. Besides
configuring bit-6 and bit-13 in Page 0 Register 0 (Copper Control
Register), it is also required to configure same bits in Page 2
Register 21 (MAC Specific Control Register 2) according to speed of
the loopback is operating.
Tested working on Marvell88E1510 PHY for all speeds (1000/100/10Mbps).
FIXME: Based on trial and error test, it seem 1G need to have delay between
soft reset and loopback enablement.
Fixes: 014068dcb5 ("net: phy: genphy_loopback: add link speed configuration")
Cc: <stable@vger.kernel.org> # 5.15.x
Signed-off-by: Mohammad Athari Bin Ismail <mohammad.athari.ismail@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't populate the read-only const array offsets on the stack
but instead make it static. Also makes the object code a little smaller.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220109231716.59012-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Corentin Labbe reports that the SSI 1328 does not work when allowing
the PHY to operate at gigabit speeds, but does work with the generic
PHY driver.
This appears to be because m88e1118_config_init() writes a fixed value
to the MSCR register, claiming that this is to enable 1G speeds.
However, this always sets bits 4 and 5, enabling RGMII transmit and
receive delays. The suspicion is that the original board this was
added for required the delays to make 1G speeds work.
Add the necessary configuration for RGMII delays for the 88E1118 to
bring this into line with the requirements for RGMII support, and thus
make the SSI 1328 work.
Corentin Labbe has tested this on gemini-ssi1328 and gemini-ns2502.
Reported-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use phy_write_paged() in m88e1118_config_init() to set the MSCR value.
We leave the other paged write for the LEDs in case the DT register
parsing is relying on this page.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for external timestamp and periodic signal output.
TJA1103 have one periodic signal and one external time stamp signal that
can be multiplexed on all 11 gpio pins.
The periodic signal can be only enabled or disabled. Have no start time
and if is enabled will be generated with a period of one second in sync
with the LTC seconds counter. The phase change is possible only with a
half of a second.
The external timestamp signal has no interrupt and no valid bit and
that's why the timestamps are handled by polling in .do_aux_work.
Signed-off-by: Radu Pirea (NXP OSS) <radu-nicolae.pirea@oss.nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On systems with large numbers of MDIO bus/muxes the message indicating
that a given MDIO bus has been successfully probed is repeated for as
many buses we have, which can eat up substantial boot time for no
reason, demote to a debug print.
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220103194024.2620-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit b45396afa4 ("net: phy:
fixed_phy: Fix NULL vs IS_ERR() checking in __fixed_phy_register")
since it prevents any system that uses a fixed PHY without a GPIO
descriptor from properly working:
[ 5.971952] brcm-systemport 9300000.ethernet: failed to register fixed PHY
[ 5.978854] brcm-systemport: probe of 9300000.ethernet failed with error -22
[ 5.986047] brcm-systemport 9400000.ethernet: failed to register fixed PHY
[ 5.992947] brcm-systemport: probe of 9400000.ethernet failed with error -22
Fixes: b45396afa4 ("net: phy: fixed_phy: Fix NULL vs IS_ERR() checking in __fixed_phy_register")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220103193453.1214961-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c
commit 077cdda764 ("net/mlx5e: TC, Fix memory leak with rules with internal port")
commit 31108d142f ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
commit 4390c6edc0 ("net/mlx5: Fix some error handling paths in 'mlx5e_tc_add_fdb_flow()'")
https://lore.kernel.org/all/20211229065352.30178-1-saeed@kernel.org/
net/smc/smc_wr.c
commit 49dc9013e3 ("net/smc: Use the bitmap API when applicable")
commit 349d43127d ("net/smc: fix kernel panic caused by race of smc_sock")
bitmap_zero()/memset() is removed by the fix
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The fixed_phy_get_gpiod function() returns NULL, it doesn't return error
pointers, using NULL checking to fix this.i
Fixes: 5468e82f70 ("net: phy: fixed-phy: Drop GPIO from fixed_phy_add()")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20211224021500.10362-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add config_init for LAN8814. This function is required for the following
reasons:
- we need to make sure that the PHY is reset,
- disable ANEG with QSGMII PCS Host side
- swap the MDI-X A,B transmit so that there will not be any link flip-flaps
when the PHY gets a link.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for Link up or Link down
interrupt support in LAN8814 Quad phy
Signed-off-by: Divya Koppera <Divya.Koppera@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211221112217.9502-1-Divya.Koppera@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a hook for PCS to validate the link parameters. This avoids MAC
drivers having to have knowledge of their PCS in their validate()
method, thereby allowing several MAC drivers to be simplfied.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac_select_pcs() allows us to have an explicit point to query which
PCS the MAC wishes to use for a particular PHY interface mode, thereby
allowing us to add support to validate the link settings with the PCS.
Phylink will also use this to select the PCS to be used during a major
configuration event without the MAC driver needing to call
phylink_set_pcs().
Note that if mac_select_pcs() is present, the supported_interfaces
bitmap must be filled in; this avoids mac_select_pcs() being called
with PHY_INTERFACE_MODE_NA when we want to get support for all
interface types. Phylink will return an error in phylink_create()
unless this condition is satisfied.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 94dd016ae5 ("bond: pass get_ts_info and SIOC[SG]HWTSTAMP
ioctl to active device") the user could get bond active interface's
PHC index directly. But when there is a failover, the bond active
interface will change, thus the PHC index is also changed. This may
break the user's program if they did not update the PHC timely.
This patch adds a new hwtstamp_config flag HWTSTAMP_FLAG_BONDED_PHC_INDEX.
When the user wants to get the bond active interface's PHC, they need to
add this flag and be aware the PHC index may be changed.
With the new flag. All flag checks in current drivers are removed. Only
the checking in net_hwtstamp_validate() is kept.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, a patch has been submitted to "fix" the refcounting for a DT
node in of_mdiobus_link_mdiodev(). This is not a leaked refcount. The
refcount is passed to the new device.
Sadly, coccicheck identifies this location as a leaked refcount, which
means we're likely to keep getting patches to "fix" this. However,
fixing this will cause breakage. Add a comment to state that the lack
of of_node_put() here is intentional.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY settings table is supposed to be sorted by descending match
priority - in other words, earlier entries are preferred over later
entries.
The order of 1000baseKX/Full and 1000baseT/Full is such that we
prefer 1000baseKX/Full over 1000baseT/Full, but 1000baseKX/Full is
a lot rarer than 1000baseT/Full, and thus is much less likely to
be preferred.
This causes phylink problems - it means a fixed link specifying a
speed of 1G and full duplex gets an ethtool linkmode of 1000baseKX/Full
rather than 1000baseT/Full as would be expected - and since we offer
userspace a software emulation of a conventional copper PHY, we want
to offer copper modes in preference to anything else. However, we do
still want to allow the rarer modes as well.
Hence, let's reorder these two modes to prefer copper.
Tested-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/E1muvFO-00F6jY-1K@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the legacy flag to indicate whether we should operate in legacy
mode. This allows us to stop using the presence of a PCS as an
indicator to the age of the phylink user, and make PCS presence
optional.
Legacy mode involves:
1) calling mac_config() whenever the link comes up
2) calling mac_config() whenever the inband advertisement changes,
possibly followed by a call to mac_an_restart()
3) making use of mac_an_restart()
4) making use of mac_pcs_get_state()
All the above functionality was moved to a seperate "PCS" block of
operations in March 2020.
Update the documents to indicate that the differences that this flag
makes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tidy up the disable bit clearing where we clear a bit
and then run the link resolver.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1ms4Rx-00EKEc-En@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On mv88e6xxx 1G/2.5G PCS, the SerDes register 4.2001.2 has the following
description:
This register bit indicates when link was lost since the last
read. For the current link status, read this register
back-to-back.
Thus to get current link state, we need to read the register twice.
But doing that in the link change interrupt handler would lead to
potentially ignoring link down events, which we really want to avoid.
Thus this needs to be solved in phylink's resolve, by retriggering
another resolve in the event when PCS reports link down and previous
link was up, and by re-reading PCS state if the previous link was down.
The wrong value is read when phylink requests change from sgmii to
2500base-x mode, and link won't come up. This fixes the bug.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On PHY state change the phylink_resolve() function can read stale
information from the MAC and report incorrect link speed and duplex to
the kernel message log.
Example with a Marvell 88X3310 PHY connected to a SerDes port on Marvell
88E6393X switch:
- PHY driver triggers state change due to PHY interface mode being
changed from 10gbase-r to 2500base-x due to copper change in speed
from 10Gbps to 2.5Gbps, but the PHY itself either hasn't yet changed
its interface to the host, or the interrupt about loss of SerDes link
hadn't arrived yet (there can be a delay of several milliseconds for
this), so we still think that the 10gbase-r mode is up
- phylink_resolve()
- phylink_mac_pcs_get_state()
- this fills in speed=10g link=up
- interface mode is updated to 2500base-x but speed is left at 10Gbps
- phylink_major_config()
- interface is changed to 2500base-x
- phylink_link_up()
- mv88e6xxx_mac_link_up()
- .port_set_speed_duplex()
- speed is set to 10Gbps
- reports "Link is Up - 10Gbps/Full" to dmesg
Afterwards when the interrupt finally arrives for mv88e6xxx, another
resolve is forced in which we get the correct speed from
phylink_mac_pcs_get_state(), but since the interface is not being
changed anymore, we don't call phylink_major_config() but only
phylink_mac_config(), which does not set speed/duplex anymore.
To fix this, we need to force the link down and trigger another resolve
on PHY interface change event.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 4904b6ea1f ("net: phy: phylink: Use PHY device interface if
N/A") introduced handling for the phy interface mode where this is not
known at phylink creation time. This was never added to the OF/fwnode
paths, but is necessary when the phy is present in DT, but the phy-mode
is not specified.
Add this handling.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices expose memory-mapped c22-compliant PHYs. Because these
devices do not have an MDIO bus, we cannot use the existing helpers.
Refactor the existing helpers to allow supplying the values for c22
registers directly, instead of using MDIO to access them. Only get_state
and set_advertisement are converted, since they contain the most complex
logic. Because set_advertisement is never actually used outside
phylink_mii_c22_pcs_config, move the MDIO-writing part into that
function. Because some modes do not need the advertisement register set
at all, we use -EINVAL for this purpose.
Additionally, a new function phylink_pcs_enable_an is provided to
determine whether to enable autonegotiation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the TI DP83561-SP Gigabit ethernet phy device.
The dp83561-sp is a radiation hardened space grade gigabit ethernet
PHY. It has been tested for single event latch upto 121 MeV, the
critical reliability parameter for space designs. It interfaces directly to
twisted pair media through an external transformer. And the device also
interfaces directly to the MAC layer through Reduced GMII (RGMII) and MII.
DP83867, DP83869 and DP83561-SP, all these parts support 1000Base-T/
100Base-TX/ and 10Base-Te standards and have similar register map for
the core functionality.
The data sheet for this part is at https://www.ti.com/product/DP83561-SP
Signed-off-by: Hari Nagalla <hnagalla@ti.com>
Signed-off-by: Geet Modi <geet.modi@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211118102532.9835-1-hnagalla@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
1000base-KX was missed in phylink_caps_to_linkmodes(), add it. This
will be necessary to convert stmmac with xpcs to ensure we don't drop
any supported linkmodes.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Killing the kernel because a certain MDIO bus object is not in the
desired state at various points in the registration or unregistration
paths is excessive and is not helping in troubleshooting or fixing
issues. Replace the BUG_ON() with WARN() and print out the MDIO bus name
to facilitate debugging.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
SMII has not been documented in the kernel, but information on this PHY
interface mode has been recently found. Document it, and correct the
recently introduced phylink handling for this interface mode.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/E1mmfVl-0075nP-14@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a generic validate() implementation using the supported_interfaces
and a bitmask of MAC pause/speed/duplex capabilities. This allows us
to entirely eliminate many driver private validate() implementations.
We expose the underlying phylink_get_linkmodes() function so that
drivers which have special needs can still benefit from conversion.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Zhang there's a small issue if in forced mode the duplex
mode changes with the link staying up [0]. In this case the MAC isn't
notified about the change.
The proposed patch relies on the phylib state machine and ignores the
fact that there are drivers that uses phylib but not the phylib state
machine. So let's don't change the behavior for such drivers and fix
it w/o re-adding state PHY_FORCING for the case that phylib state
machine is used.
[0] https://lore.kernel.org/netdev/a5c26ffd-4ee4-a5e6-4103-873208ce0dc5@huawei.com/T/
Fixes: 2bd229df5e ("net: phy: remove state PHY_FORCING")
Reported-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Tested-by: Zhang Changzhong <zhangchangzhong@huawei.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/7b8b9456-a93f-abbc-1dc5-a2c2542f932c@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add a function to initialize phy rgmii delay according to phydev->interface.
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211101162119.29275-1-yuiko.oshino@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
mvneta does not support asymetric pause modes, and it flags this by the
lack of AsymPause in the supported field. When setting pause modes, we
check that pause->rx_pause == pause->tx_pause, but only when pause
autoneg is enabled. When pause autoneg is disabled, we still allow
pause->rx_pause != pause->tx_pause, which is incorrect when the MAC
does not support asymetric pause, and causes mvneta to issue a warning.
Fix this by removing the test for pause->autoneg, so we always check
that pause->rx_pause == pause->tx_pause for network devices that do not
support AsymPause.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a basic cable test (diagnostic) support for lan87xx phy.
Tested with LAN8770 for connected/open/short wires using ethtool.
Signed-off-by: Yuiko Oshino <yuiko.oshino@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following coccicheck warning:
./drivers/net/phy/at803x.c:493:5-10: WARNING: Unsigned expression
compared with zero: value < 0.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Fixes: 7beecaf7d5 ("net: phy: at803x: improve the WOL feature")
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/1635325191-101815-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fixed warning: Function parameter or member 'enable' not
described in 'genphy_c45_fast_retrain'
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211026102957.17100-1-luoj@codeaurora.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If the network device supplies a supported interface bitmap, we can use
that during phylink's validation to simplify MAC drivers in two ways by
using the supported_interfaces bitmap to:
1. reject unsupported interfaces before calling into the MAC driver.
2. generate the set of all supported link modes across all supported
interfaces (used mainly for SFP, but also some 10G PHYs.)
Suggested-by: Sean Anderson <sean.anderson@seco.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a race condition where the PHY state machine can change
members of the phydev structure at the same time userspace requests a
change via ethtool. To prevent this, have phy_ethtool_ksettings_set
take the PHY lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Reported-by: Walter Stoll <Walter.Stoll@duagon.com>
Suggested-by: Walter Stoll <Walter.Stoll@duagon.com>
Tested-by: Walter Stoll <Walter.Stoll@duagon.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split phy_start_aneg into a wrapper which takes the PHY lock, and a
helper doing the real work. This will be needed when
phy_ethtook_ksettings_set takes the lock.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows it to make use of a helper which assume the PHY is already
locked.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PHY structure should be locked while copying information out if
it, otherwise there is no guarantee of self consistency. Without the
lock the PHY state machine could be updating the structure.
Fixes: 2d55173e71 ("phy: add generic function to support ksetting support")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
To perform CDT of qca8081 phy:
1. disable hibernation.
2. force phy working in MDI mode.
3. force phy working in 1000BASE-T mode.
4. configure the related thresholds.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. The master/slave seed needs to be updated when the link can't
be created.
2. The case where two qca8081 PHYs are connected each other and
master/slave seed is generated as the same value also needs
to be considered, so adding this code change into read_status
instead of link_change_notify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 phy is a single port phy, configure
phy the lower seed value to make it linked as slave
mode easier.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the qca8081 phy driver config_init function, which includes:
1. Enable fast restrain.
2. Add 802.3az configurations.
3. Initialize ADC threshold as 100mv.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add generic fast retrain auto-negotiation function for C45 PHYs.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse at803x phy driver config_aneg excepting
adding 2500M auto-negotiation.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reuse the at803x phy driver get_features excepting
adding 2500M capability.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Separate the function at803x_read_specific_status from
the at803x_read_status, since it can be reused by the
read_status of qca8081 phy driver excepting adding the
2500M speed.
2. Add the qca8081 read_status function qca808x_read_status.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca8081 is a single port ethernet phy chip that supports
10/100/1000/2500 Mbps mode.
Add the basic phy driver features, and reuse the at803x
phy driver functions.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use GENMASK() for the current speed value.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wol feature is controlled by the MMD3.8012 bit5,
need to set this bit when the wol function is enabled.
The reg18 bit0 is for enabling WOL interrupt, when wol
occurs, the wol interrupt status reg19 bit0 is set to 1.
Call phy_trigger_machine if there are any other interrupt
pending in the function set_wol.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert at803x_set_wol to use phy_modify.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace AT803X_DEVICE_ADDR with MDIO_MMD_PCS defined in mdio.h.
Signed-off-by: Luo Jie <luoj@codeaurora.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev->dev_addr will become a const soon(ish),
constify the local variables referring to it.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
7712 is a 16nm process SoC with a 10/100 integrated Ethernet PHY,
utilize the recently defined 16nm EPHY macro to configure that PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
This refactors the phylink pcs helper functions to use mdiobus_* instead
of mdiodev_*.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Micrel KSZ8041NL PHY chips exhibit continuous RX errors after using
the power down mode bit (0.11). If the PHY is taken out of power down
mode in a certain temperature range, the PHY enters a weird state which
leads to continuously reporting RX errors. In that state, the MAC is not
able to receive or send any Ethernet frames and the activity LED is
constantly blinking. Since Linux is using the suspend callback when the
interface is taken down, ending up in that state can easily happen
during a normal startup.
Micrel confirmed the issue in errata DS80000700A [*], caused by abnormal
clock recovery when using power down mode. Even the latest revision (A4,
Revision ID 0x1513) seems to suffer that problem, and according to the
errata is not going to be fixed.
Remove the suspend/resume callback to avoid using the power down mode
completely.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/80000700A.pdf
Fixes: 1a5465f5d6 ("phy/micrel: Add suspend/resume support to Micrel PHYs")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The auto-negotiation state in the PCS as set by
phylink_mii_c22_pcs_config was previously always enabled when the
driver is configured for in-band autonegotiation, even if
autonegotiation was disabled on the interface with ethtool. Update the
code to set the BMCR_ANENABLE bit based on the interface's
autonegotiation enabled state.
Update phylink_mii_c22_pcs_get_state to not check
autonegotiation-related fields when autonegotiation is disabled.
Update phylink_mac_pcs_get_state to initialize the state based on the
interface's configured speed, duplex and pause parameters rather than
to unknown when autonegotiation is disabled, before calling the
driver's pcs_get_state functions, as they are not likely to provide
meaningful data for these fields when autonegotiation is disabled. In
this case the driver is really just filling in the link state field.
Note that in cases where there is a downstream PHY connected, such as
with SGMII and a copper PHY, the configuration set by ethtool is
handled by phy_ethtool_ksettings_set and not propagated to the PCS.
This is correct since SGMII or 1000Base-X autonegotiation with the PCS
should normally still be used even if the copper side has disabled it.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit ea269a6f72 ("net: phylink: Update SFP selected interface on
advertising changes") added a better solution to selecting the
interface mode for SFPs using the advertisement mask. This method will
work for mvneta and mvpp2 when selecting between 2500base-X and
1000base-X without needing to use the basex helper, or indicate that
we support both 1000base-X and 2500base-X when in either of these two
interface modes.
Hence, we need to eliminate the validation prior to selecting the
interface, otherwise when we clean up mvneta's validation function, we
will end up locking to 2500base-X as we validate with an interface mode
of PHY_INERFACE_MODE_2500BASEX.
The supported mask will already have been reduced down to the union of
support for the SFP and MAC already, so we can be confident that the
advertisement mask is already appropriately restricted. We only need to
select the appropriate interface, and then revalidate with the new
interface mode.
We get rid of the check for pl->sfp_port too, this is meaningless here
as it doesn't get cleared when a module is removed, so it doesn't
indicate if a module is present. Just rely on pl->sfp_bus.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RTL8365MB-VC ethernet switch controller has 4 internal PHYs for its
user-facing ports. All that is needed is to let the PHY driver core
pick up the IRQ made available by the switch driver.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY driver dp83867 has rich supports for OF-platform to fine-tune the PHY
chip during phy configuration. However, for non-OF platform, certain PHY
tunable parameters such as IO impedance and RX & TX internal delays are
critical and should be initialized to its default during PHY driver probe.
Tested-by: Clement <clement@intel.com>
Signed-off-by: Lay, Kuan Loon <kuan.loon.lay@intel.com>
Co-developed-by: Ong Boon Leong <boon.leong.ong@intel.com>
Signed-off-by: Ong Boon Leong <boon.leong.ong@intel.com>
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://lore.kernel.org/r/20211013065941.2124858-1-boon.leong.ong@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It seems reasonable to fine-tune only some of the skew values when using
one of the rgmii-*id PHY modes, and even when all skew values are
specified, using the correct ID PHY mode makes sense for documentation
purposes. Such a configuration also appears in the binding docs in
Documentation/devicetree/bindings/net/micrel-ksz90x1.txt, so the driver
should not warn about it.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211012103402.21438-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tools/testing/selftests/net/ioam6.sh
7b1700e009 ("selftests: net: modify IOAM tests for undef bits")
bf77b1400a ("selftests: net: Test for the IOAM encapsulation with IPv6")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Give a name to known debug regs from Documentation instead of using
unknown hex values.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
From original QCA source code the port was set to prefer master as port
type in 1000BASE-T mode. Apply the same settings also here.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
QCA8327 internal phy require DAC amplitude adjustement set to +6% with
100m speed. Also add additional define to report a change of the same
reg in QCA8337. (different scope it does set 1000m voltage)
Add link_change_notify function to set the proper amplitude adjustement
on PHY_RUNNING state and disable on any other state.
Fixes: b4df02b562 ("net: phy: at803x: add support for qca 8327 A variant internal phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From Documentation phy resume triggers phy reset and restart
auto-negotiation. Add a dedicated function to wait reset to finish as
it was notice a regression where port sometime are not reliable after a
suspend/resume session. The reset wait logic is copied from phy_poll_reset.
Add dedicated suspend function to use genphy_suspend only with QCA8337
phy and set only additional debug settings for QCA8327. With more test
it was reported that QCA8327 doesn't proprely support this mode and
using this cause the unreliability of the switch ports, especially the
malfunction of the port0.
Fixes: 15b9df4ece ("net: phy: at803x: add resume/suspend function to qca83xx phy")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case a PHY device was probed thus in the PHY_READY state, but not
configured and with no network device attached yet, we should not be
trying to shut it down because it has been brought back into reset by
phy_device_reset() towards the end of phy_probe() and anyway we have not
configured the PHY yet.
Fixes: e2f016cf77 ("net: phy: add a shutdown procedure")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Micrel KSZ9131 PHY LED behavior is not correct when configured in
Individual Mode, LED1 (Activity LED) is in the ON state when there is
no-link.
Workaround this by setting bit 9 of register 0x1e after verifying that
the LED configuration is Individual Mode.
This issue is described in KSZ9131RNX Silicon Errata DS80000693B [*]
and according to that it will not be corrected in a future silicon
revision.
[*] https://ww1.microchip.com/downloads/en/DeviceDoc/KSZ9131RNX-Silicon-Errata-and-Data-Sheet-Clarification-80000863B.pdf
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHYLIB device drivers must match by either numerical PHY ID or by their
.match_phy_device method. Matching by DT is not permitted.
Link: https://lore.kernel.org/r/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
On the MDIO bus, we have PHYLIB devices and drivers, and we have non-
PHYLIB devices and drivers. PHYLIB devices are MDIO devices that are
wrapped with a struct phy_device.
Trying to bind a MDIO device with a PHYLIB driver results in out-of-
bounds accesses as we attempt to access struct phy_device members. So,
let's prevent this by ensuring that the type of the MDIO device
(indicated by the MDIO_DEVICE_FLAG_PHY flag) matches the type of the
MDIO driver (indicated by the MDIO_DEVICE_IS_PHY flag.)
Link: https://lore.kernel.org/r/2b1dc053-8c9a-e3e4-b450-eecdfca3fe16@gmail.com
Tested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
netfilter, and wireless.
Current release - regressions:
- xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting
a new value in the middle of an enum
- unix: fix an issue in unix_shutdown causing the other end
read/write failures
- phy: mdio: fix memory leak
Current release - new code bugs:
- mlx5e: improve MQPRIO resiliency against bad configs
Previous releases - regressions:
- bpf: fix integer overflow leading to OOB access in map element
pre-allocation
- stmmac: dwmac-rk: fix ethernet on rk3399 based devices
- netfilter: conntrack: fix boot failure with nf_conntrack.enable_hooks=1
- brcmfmac: revert using ISO3166 country code and 0 rev as fallback
- i40e: fix freeing of uninitialized misc IRQ vector
- iavf: fix double unlock of crit_lock
Previous releases - always broken:
- bpf, arm: fix register clobbering in div/mod implementation
- netfilter: nf_tables: correct issues in netlink rule change
event notifications
- dsa: tag_dsa: fix mask for trunked packets
- usb: r8152: don't resubmit rx immediately to avoid soft lockup
on device unplug
- i40e: fix endless loop under rtnl if FW fails to correctly
respond to capability query
- mlx5e: fix rx checksum offload coexistence with ipsec offload
- mlx5: force round second at 1PPS out start time and allow it
only in supported clock modes
- phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
sequence
Misc:
- xfrm: slightly rejig the new policy uAPI to make it less cryptic
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=xzZg
-----END PGP SIGNATURE-----
Merge tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from xfrm, bpf, netfilter, and wireless.
Current release - regressions:
- xfrm: fix XFRM_MSG_MAPPING ABI breakage caused by inserting a new
value in the middle of an enum
- unix: fix an issue in unix_shutdown causing the other end
read/write failures
- phy: mdio: fix memory leak
Current release - new code bugs:
- mlx5e: improve MQPRIO resiliency against bad configs
Previous releases - regressions:
- bpf: fix integer overflow leading to OOB access in map element
pre-allocation
- stmmac: dwmac-rk: fix ethernet on rk3399 based devices
- netfilter: conntrack: fix boot failure with
nf_conntrack.enable_hooks=1
- brcmfmac: revert using ISO3166 country code and 0 rev as fallback
- i40e: fix freeing of uninitialized misc IRQ vector
- iavf: fix double unlock of crit_lock
Previous releases - always broken:
- bpf, arm: fix register clobbering in div/mod implementation
- netfilter: nf_tables: correct issues in netlink rule change event
notifications
- dsa: tag_dsa: fix mask for trunked packets
- usb: r8152: don't resubmit rx immediately to avoid soft lockup on
device unplug
- i40e: fix endless loop under rtnl if FW fails to correctly respond
to capability query
- mlx5e: fix rx checksum offload coexistence with ipsec offload
- mlx5: force round second at 1PPS out start time and allow it only
in supported clock modes
- phy: pcs: xpcs: fix incorrect CL37 AN sequence, EEE disable
sequence
Misc:
- xfrm: slightly rejig the new policy uAPI to make it less cryptic"
* tag 'net-5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (66 commits)
net: prefer socket bound to interface when not in VRF
iavf: fix double unlock of crit_lock
i40e: Fix freeing of uninitialized misc IRQ vector
i40e: fix endless loop under rtnl
dt-bindings: net: dsa: marvell: fix compatible in example
ionic: move filter sync_needed bit set
gve: report 64bit tx_bytes counter from gve_handle_report_stats()
gve: fix gve_get_stats()
rtnetlink: fix if_nlmsg_stats_size() under estimation
gve: Properly handle errors in gve_assign_qpl
gve: Avoid freeing NULL pointer
gve: Correct available tx qpl check
unix: Fix an issue in unix_shutdown causing the other end read/write failures
net: stmmac: trigger PCS EEE to turn off on link down
net: pcs: xpcs: fix incorrect steps on disable EEE
netlink: annotate data races around nlk->bound
net: pcs: xpcs: fix incorrect CL37 AN sequence
net: sfp: Fix typo in state machine debug string
net/sched: sch_taprio: properly cancel timer from taprio_destroy()
net: bridge: fix under estimation in br_get_linkxstats_size()
...
Use the mdiobus_modify_changed() helper in the C22 PCS advertisement
helper.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add mdiobus_modify_changed() helper to reflect the phylib and similar
equivalents. This will avoid this functionality being open-coded, as
has already happened in phylink, and it looks like other users will be
appearing soon.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the embedded fast-ethernet PHY found on the QCA9561
WiSoC platform. It supports the usual Atheros PHY featureset including
the cable tester.
Tested on a Xiaomi MiRouter 4Q (QCA9561)
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David Bauer <mail@david-bauer.net>
Link: https://lore.kernel.org/r/20211005225401.10653-1-mail@david-bauer.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The string should be "tx_disable" to match the state enum.
Fixes: 4005a7cb4f ("net: phy: sftp: print debug message with text, not numbers")
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a helper for setting 10Gigabit modes, so we have one central
place that sets all appropriate 10G modes for a driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here are some driver core and kernfs fixes for reported issues for
5.15-rc4. These fixes include:
- kernfs positive dentry bugfix
- debugfs_create_file_size error path fix
- cpumask sysfs file bugfix to preserve the user/kernel abi (has
been reported multiple times.)
- devlink fixes for mdiobus devices as reported by the subsystem
maintainers.
Also included in here are some devlink debugging changes to make it
easier for people to report problems when asked. They have already
helped with the mdiobus and other subsystems reporting issues.
All of these have been linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYVmC1A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfCQCgtQ0kdPoPdUG6mPCn45rrbJQLBY4AnRL5JyhO
zB60l6C2EHHnLnRxMnQq
=gygB
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here are some driver core and kernfs fixes for reported issues for
5.15-rc4. These fixes include:
- kernfs positive dentry bugfix
- debugfs_create_file_size error path fix
- cpumask sysfs file bugfix to preserve the user/kernel abi (has been
reported multiple times.)
- devlink fixes for mdiobus devices as reported by the subsystem
maintainers.
Also included in here are some devlink debugging changes to make it
easier for people to report problems when asked. They have already
helped with the mdiobus and other subsystems reporting issues.
All of these have been linux-next for a while with no reported issues"
* tag 'driver-core-5.15-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
kernfs: also call kernfs_set_rev() for positive dentry
driver core: Add debug logs when fwnode links are added/deleted
driver core: Create __fwnode_link_del() helper function
driver core: Set deferred probe reason when deferred by driver core
net: mdiobus: Set FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD for mdiobus parents
driver core: fw_devlink: Add support for FWNODE_FLAG_NEEDS_CHILD_BOUND_ON_ADD
driver core: fw_devlink: Improve handling of cyclic dependencies
cpumask: Omit terminating null byte in cpumap_print_{list,bitmask}_to_buf
debugfs: debugfs_create_file_size(): use IS_ERR to check for error
Syzbot reported memory leak in MDIO bus interface, the problem was in
wrong state logic.
MDIOBUS_ALLOCATED indicates 2 states:
1. Bus is only allocated
2. Bus allocated and __mdiobus_register() fails, but
device_register() was called
In case of device_register() has been called we should call put_device()
to correctly free the memory allocated for this device, but mdiobus_free()
calls just kfree(dev) in case of MDIOBUS_ALLOCATED state
To avoid this behaviour we need to set bus->state to MDIOBUS_UNREGISTERED
_before_ calling device_register(), because put_device() should be
called even in case of device_register() failure.
Link: https://lore.kernel.org/netdev/YVMRWNDZDUOvQjHL@shell.armlinux.org.uk/
Fixes: 46abc02175 ("phylib: give mdio buses a device tree presence")
Reported-and-tested-by: syzbot+398e7dc692ddbbb4cfec@syzkaller.appspotmail.com
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/eceae1429fbf8fa5c73dd2a0d39d525aa905074d.1633024062.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit ab609f25d1.
This patch is correct in the sense that we _should_ call device_put() in
case of device_register() failure, but the problem in this code is more
vast.
We need to set bus->state to UNMDIOBUS_REGISTERED before calling
device_register() to correctly release the device in mdiobus_free().
This patch prevents us from doing it, since in case of device_register()
failure put_device() will be called 2 times and it will cause UAF or
something else.
Also, Reported-by: tag in revered commit was wrong, since syzbot
reported different leak in same function.
Link: https://lore.kernel.org/netdev/20210928092657.GI2048@kadam/
Acked-by: Yanfei Xu <yanfei.xu@windriver.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/f12fb1faa4eccf0f355788225335eb4309ff2599.1633024062.git.paskripkin@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for the downshift tunable for the Marvell 88x3310 PHY.
Downshift is only usable with firmware 0.3.5.0 and later.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When EEE support was added to the 28nm EPHY it was assumed that it would
be able to support the standard clause 45 over clause 22 register access
method. It turns out that the PHY does not support that, which is the
very reason for using the indirect shadow mode 2 bank 3 access method.
Implement {read,write}_mmd to allow the standard PHY library routines
pertaining to EEE querying and configuration to work correctly on these
PHYs. This forces us to implement a __phy_set_clr_bits() function that
does not grab the MDIO bus lock since the PHY driver's {read,write}_mmd
functions are always called with that lock held.
Fixes: 83ee102a69 ("net: phy: bcm7xxx: add support for 28nm EPHY")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
