check the return value of of_address_to_resource() and also add
missing of_node_put() for np and npp nodes.
Fixes: e0a3bc6544 ("net: emaclite: Support multiple phys connected to one MDIO bus")
Addresses-Coverity: Event check_return value.
Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In xemaclite_open() function we are setting the max speed of
emaclite to 100Mb using phy_set_max_speed() function so,
there is no need to write the advertising registers to stop
giga-bit speed and the phy_start() function starts the
auto-negotiation so, there is no need to handle it separately
using advertising registers. Remove the phy_read and phy_write
of advertising registers in xemaclite_open() function.
Signed-off-by: Shravya Kumbham <shravya.kumbham@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In some SGMII use cases where both a fixed link external PHY and the
internal PCS/PMA PHY need to be configured, we should explicitly use a
phandle "pcs-phy" to get the reference to the PCS/PMA PHY. Otherwise, the
driver would use "phy-handle" in the DT as the reference to both the
external and the internal PCS/PMA PHY.
In other cases where the core is connected to a SFP cage, we could still
point phy-handle to the intenal PCS/PMA PHY, and let the driver connect
to the SFP module, if exist, via phylink.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the struct member `phy_node` of struct axienet_local is not used by the
driver anymore after initialization. It might be a remnent of old code
and could be removed.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to axienet_mdio_setup should not depend on whether "phy-node"
pressents on the DT. Besides, since `lp->phy_node` is used if PHY is in
SGMII or 100Base-X modes, move it into the if statement. And the next patch
will remove `lp->phy_node` from driver's private structure and do an
of_node_put on it right away after use since it is not used elsewhere.
Signed-off-by: Andy Chiu <andy.chiu@sifive.com>
Reviewed-by: Greentime Hu <greentime.hu@sifive.com>
Reviewed-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use napi_alloc_skb to allocate memory when refilling the RX ring
in axienet_poll for more efficiency. napi_alloc_skb() can reuse
softirq-local cache of freed skbs which may still be cache-warm
and skipping allocator calls.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220308211013.1530955-1-robert.hancock@calian.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This node pointer is returned by of_parse_phandle() with refcount
incremented in this function. Calling of_node_put() to avoid the
refcount leak. As the remove function do.
Fixes: 5cdaaa1286 ("net: emaclite: adding MDIO and phy lib support")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220308024751.2320-1-linmq006@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the ability to configure the RX/TX coalesce timer with ethtool.
Change default setting to scale with the clock rate rather than being a
fixed number of clock cycles.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that NAPI has been implemented, the hardware interrupt mitigation
mechanism is not needed to avoid excessive interrupt load in most cases.
Reduce the default RX interrupt threshold to 1 to reduce introduced
latency. This can be increased with ethtool if desired if some applications
still want to reduce interrupts.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement NAPI and GRO receive. In addition to better performance, this
also avoids handling RX packets in hard IRQ context, which reduces the
IRQ latency impact to other devices.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the RX or TX coalesce count is set to 1, there's no point in
setting the delay timer value since an interrupt will already be raised
on every packet, and the delay interrupt just causes extra pointless
interrupts.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the DMA error handling process, and remove some duplicated code
between the DMA error handling and the stop function.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using lp->ndev.parent to find the correct device to use for
DMA API calls, just use the dev attribute in the device structure.
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a memory allocation error occurred during an attempt to refill a slot
in the RX ring after the packet was received, the hardware tail pointer
would still have been updated to point to or past the slot which remained
marked as previously completed. This would likely result in the DMA engine
raising an error when it eventually tried to use that slot again.
If a slot cannot be refilled, then just stop processing and do not move
the tail pointer past it. On the next attempt, we should skip receiving
the packet from the empty slot and just try to refill it again.
This failure mode has not actually been observed, but was found as part
of other driver updates.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_kmalloc() returns a pointer to allocated memory on success, NULL
on failure. While lp->indirect_lock is allocated by devm_kmalloc()
without proper check. It is better to check the value of it to
prevent potential wrong memory access.
Fixes: f14f5c11f0 ("net: ll_temac: Support indirect_mutex share within TEMAC IP")
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the second 'the'.
Replacements:
endiannes to endianness
areconnected to are connected
Mamagement to Management
undoccumented to undocumented
Xilink to Xilinx
strucutre to structure
Change kernel-doc comment style to c style for
/* Management ...
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
XTE_MAX_JUMBO_FRAME_SIZE is over 9000 bytes and the default value for
'rx_bd_num' is RX_BD_NUM_DEFAULT (i.e. 1024)
So this loop allocates more than 9 Mo of memory.
Previous memory allocations in this function already use GFP_KERNEL, so
use __netdev_alloc_skb_ip_align() and an explicit GFP_KERNEL instead of a
implicit GFP_ATOMIC.
This gives more opportunities of successful allocation.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/694abd65418b2b3974106a82d758e3474c65ae8f.1645042560.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Commit 0ebecb2644 ("net: mdio: Add helper functions for accessing
MDIO devices") added support for mdiodev accessor operations that
neatly wrap the mdiobus accessor operations. Since we are dealing with
a mdio device here, update the driver to use mdiodev_write().
Tested-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert axienet to use the phylink_pcs layer, resulting in it no longer
being a legacy driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
With previous changes to make the driver handle the TX ring size more
correctly, the default TX ring size of 64 appears to significantly
bottleneck TX performance to around 600 Mbps on a 1 Gbps link on ZynqMP.
Increasing this to 128 seems to bring performance up to near line rate and
shouldn't cause excess bufferbloat (this driver doesn't yet support modern
byte-based queue management).
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Network driver documentation indicates we should be avoiding returning
NETDEV_TX_BUSY from ndo_start_xmit in normal cases, since it requires
the packets to be requeued. Instead the queue should be stopped after
a packet is added to the TX ring when there may not be enough room for an
additional one. Also, when TX ring entries are completed, we should only
wake the queue if we know there is room for another full maximally
fragmented packet.
Print a warning if there is insufficient space at the start of start_xmit,
since this should no longer happen.
Combined with increasing the default TX ring size (in a subsequent
patch), this appears to recover the TX performance lost by previous changes
to actually manage the TX ring state properly.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for the number of available TX ring slots was off by 1 since a
slot is required for the skb header as well as each fragment. This could
result in overwriting a TX ring slot that was still in use.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The check for whether a TX ring slot was available was incorrect,
since a slot which had been loaded with transmit data but the device had
not started transmitting would be treated as available, potentially
causing non-transmitted slots to be overwritten. The control field in
the descriptor should be checked, rather than the status field (which may
only be updated when the device completes the entry).
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver will not work properly if the TX ring size is set to below
MAX_SKB_FRAGS + 1 since it needs to hold at least one full maximally
fragmented packet in the TX ring. Limit setting the ring size to below
this value.
Fixes: 8b09ca823f ("net: axienet: Make RX/TX ring sizes configurable")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver was missing some required memory barriers:
Use dma_rmb to ensure we see all updates to the descriptor after we see
that an entry has been completed.
Use wmb and rmb to avoid stale descriptor status between the TX path and
TX complete IRQ path.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some cases where the Xilinx Ethernet core was used in 1000Base-X or
SGMII modes, which use the internal PCS/PMA PHY, and the MGT
transceiver clock source for the PCS was not running at the time the
FPGA logic was loaded, the core would come up in a state where the
PCS could not be found on the MDIO bus. To fix this, the Ethernet core
(including the PCS) should be reset after enabling the clocks, prior to
attempting to access the PCS using of_mdio_find_device.
Fixes: 1a02556086 (net: axienet: Properly handle PCS/PMA PHY for 1000BaseX mode)
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When resetting the device, wait for the PhyRstCmplt bit to be set
in the interrupt status register before continuing initialization, to
ensure that the core is actually ready. When using an external PHY, this
also ensures we do not start trying to access the PHY while it is still
in reset. The PHY reset is initiated by the core reset which is
triggered just above, but remains asserted for 5ms after the core is
reset according to the documentation.
The MgtRdy bit could also be waited for, but unfortunately when using
7-series devices, the bit does not appear to work as documented (it
seems to behave as some sort of link state indication and not just an
indication the transceiver is ready) so it can't really be relied on for
this purpose.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The previous timeout of 1ms was too short to handle some cases where the
core is reset just after the input clocks were started, which will
be introduced in an upcoming patch. Increase the timeout to 50ms. Also
simplify the reset timeout checking to use read_poll_timeout.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
axienet has a PCS, but does not make use of the phylink PCS support.
Mark it was a pre-March 2020 driver.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
axienet has no special behaviour in its validation implementation, so
can be switched to phylink_generic_validate().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode in the
validation function. Remove this to simplify it.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Populate the phy_interface_t bitmap for the Xilinx axienet driver with
interfaces modes supported by the MAC.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This big patch sprinkles const on local variables and
function arguments which may refer to netdev->dev_addr.
Commit 406f42fa0d ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Some of the changes here are not strictly required - const
is sometimes cast off but pointer is not used for writing.
It seems like it's still better to add the const in case
the code changes later or relevant -W flags get enabled
for the build.
No functional changes.
Link: https://lore.kernel.org/r/20211014142432.449314-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use the new of_get_ethdev_address() helper for the cases
where dev->dev_addr is passed in directly as the destination.
@@
expression dev, np;
@@
- of_get_mac_address(np, dev->dev_addr)
+ of_get_ethdev_address(np, dev)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... dev->addr_len)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, dev->addr_len)
+ eth_hw_addr_set(dev, np)
In theory addr_len may not be ETH_ALEN, but we don't expect
non-Ethernet devices to live under this directory, and only
the following cases of setting addr_len exist:
- cxgb4 for mgmt device,
and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all Ethernet drivers from memcpy(... ETH_ADDR)
to eth_hw_addr_set():
@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to support more coalesce parameters through netlink,
add two new parameter kernel_coal and extack for .set_coalesce
and .get_coalesce, then some extra info can return to user with
the netlink API.
Signed-off-by: Yufeng Mo <moyufeng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As documented in Documentation/networking/driver.rst, the ndo_start_xmit
method must not return NETDEV_TX_BUSY under any normal circumstances, and
as recommended, we simply stop the tx queue in advance, when there is a
risk that the next xmit would cause a NETDEV_TX_BUSY return.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just as the initial check, we need to ensure num_frag+1 buffers available,
as that is the number of buffers we are going to use.
This fixes a buffer overflow, which might be seen during heavy network
load. Complete lockup of TEMAC was reproducible within about 10 minutes of
a particular load.
Fixes: 84823ff80f ("net: ll_temac: Fix race condition causing TX hang")
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a couple of memory-barriers to ensure correct ordering of read/write
access to TX BDs.
In xmit_done, we should ensure that reading the additional BD fields are
only done after STS_CTRL_APP0_CMPLT bit is set.
When xmit_done marks the BD as free by setting APP0=0, we need to ensure
that the other BD fields are reset first, so we avoid racing with the xmit
path, which writes to the same fields.
Finally, making sure to read APP0 of next BD after the current BD, ensures
that we see all available buffers.
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the skb pointer piggy-backed on the TX BD, we have a simple and
efficient way to free the skb buffer when the frame has been transmitted.
But in order to avoid freeing the skb while there are still fragments from
the skb in use, we need to piggy-back on the TX BD of the skb, not the
first.
Without this, we are doing use-after-free on the DMA side, when the first
BD of a multi TX BD packet is seen as completed in xmit_done, and the
remaining BDs are still being processed.
Cc: stable@vger.kernel.org # v5.4+
Signed-off-by: Esben Haabendal <esben@geanix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
