We already had a few bugs in the past where FBC was compressing
nothing when it was enabled, which makes the feature quite useless.
Add this information to debugfs so the test suites can check for
regressions in this piece of the code.
Our igt/tests/kms_frontbuffer_tracking already has support for this
message.
v2: - Remove pointless VLV check (Ville).
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The docs don't support the 64k linear scanout alignment we impose
on gen2/3. And it really makes no sense since we have no DSPSURF
register, so the only thing that the hardware will see is the linear
offset which will be just pixel aligned anyway.
There is one case where 64k comes into the picture, and that's FBC.
The start of the line length buffer corresponds to a 64k aligned
address of the uncompressed framebuffer. So if the uncompressed fb is
not 64k aligned, the first actually used entry in the line length
buffer will not be byte 0. There are 32 extra entries in the line
length buffer to account for this extra alignment so we shouldn't
have to worry about it when mapping the uncompressed fb to the GTT.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
VLV/CHV have problems with 4k aligned linear scanout buffers. The VLV
docs got updated at some point to say that we need to align them to
128k, just like we do on gen4.
So far I've seen the problem manifest when the stride is an odd multiple
of 512 bytes, and the surface address meets the following pattern
'(addr & 0xf000) == 0x1000' (also == 0x2000 is problematic on VLV). The
result is a starcase effect (so some pages get dropped maybe?), with a
few pages here and there clearly getting scannout out at the wrong position.
I've not actually been able to reproduce this problem on gen4, so it's
not clear of the issue is any way related to the 128k restrictions
supposedly inherited from gen4. But let's hope the 128k alignment is
sufficient to hide it all.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently intel_gen4_compute_page_offset() simply picks the closest
page boundary below the linear offset. That however may not be suitably
aligned to satisfy any hardware specific restrictions. So let's make
sure the page boundary we choose is properly aligned.
Also to play it a bit safer lets split the remaining linear offset into
x and y values instead of just x. This should make no difference for
most platforms since we convert the x and y offsets back into a linear
offset before feeding them to the hardware. HSW+ are different however
and use x and y offsets even with linear buffers, so they might have
trouble if either the x or y get too big.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Corrected the documentation on the intel_edp_drrs_flush and
intel_edp_drrs_invalidate.
And accordingly edp_drrs_flush function is modified to restart the idleness
detection after upclocking.
v2: Update kerneldoc
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com> (v1)
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The i915 atomic conversion is a real beast and it's not getting easier
wrangling in a separate branch. I'm might be regretting this, but
right after vacation nothing can burst my little bubble here!
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
In igt, we want to test handling of GPU hangs, both for recovery
purposes and for reporting. However, we don't want to inject a genuine
GPU hang onto a machine that cannot recover and so be permenantly
wedged. Rather than embed heuristics into igt, have the kernel report
exactly when it expects the GPU reset to work.
This can also be usefully extended in future to indicate different
levels of fine-grained resets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tim Gore <tim.gore@intel.com>
Cc: Tomas Elf <tomas.elf@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
drivers/gpu/drm/i915/i915_debugfs.c: In function ‘i915_runtime_pm_status’:
drivers/gpu/drm/i915/i915_debugfs.c:2528:34: error: ‘struct dev_pm_info’ has no member named ‘usage_count’
atomic_read(&dev->dev->power.usage_count));
Regression from commit a6aaec8be2
Author: Damien Lespiau <damien.lespiau@intel.com>
Date: Thu Jun 4 18:23:58 2015 +0100
drm/i915: Add runtime PM's usage_count in i915_runtime_pm_status
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Damien Lespiau <damien.lespiau@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only bit 27 of SCRATCH1 and bit 6 of ROW_CHICKEN3 are allowed to be
set because of security-sensitive bits we don't want userspace to mess
with. On HSW hardware the whitelisted bits control whether atomic
read-modify-write operations are performed on L3 or on GTI, and when
set to L3 (which can be 10x-30x better performing than on GTI,
depending on the application) require great care to avoid a system
hang, so we currently program them to be handled on GTI by default.
Beignet can immediately start taking advantage of this change to
enable L3 atomics. Mesa should eventually switch to L3 atomics too,
but a number of non-trivial changes are still required so it will
continue using GTI atomics for now.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
In some cases it might be unnecessary or dangerous to give userspace
the right to write arbitrary values to some register, even though it
might be desirable to give it control of some of its bits. This patch
extends the register whitelist entries to contain a mask/value pair in
addition to the register offset. For registers with non-zero mask,
any LRM writes and LRI writes where the bits of the immediate given by
the mask don't match the specified value will be rejected.
This will be used in my next patch to grant userspace partial write
access to some sensitive registers.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Until now the software command checker assumed that commands could
read or write at most a single register per packet. This is not
necessarily the case, MI_LOAD_REGISTER_IMM expects a variable-length
list of offset/value pairs and writes them in sequence. The previous
code would only check whether the first entry was valid, effectively
allowing userspace to write unrestricted registers of the MMIO space
by sending a multi-register write with a legal first register, with
potential security implications on Gen6 and 7 hardware.
Fix it by extending the drm_i915_cmd_descriptor table to represent
multi-register access and making validate_cmd() iterate for all
register offsets present in the command packet.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
I noticed one of those and it turned out we have a few lingering around.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
It's handy to have debug message for the "big" events and this one
qualifies IMHO. Also helpful to see what's happening while we're loading
the firwmare and how much time it takes.
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In Linux, macros are usually well done and protect their arguments
properly, even avoiding multiple evaluations of the parameters. Extra ()
are really not needed.
Cc: Suketu Shah <suketu.j.shah@intel.com>
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Only bit 27 of SCRATCH1 and bit 6 of ROW_CHICKEN3 are allowed to be
set because of security-sensitive bits we don't want userspace to mess
with. On HSW hardware the whitelisted bits control whether atomic
read-modify-write operations are performed on L3 or on GTI, and when
set to L3 (which can be 10x-30x better performing than on GTI,
depending on the application) require great care to avoid a system
hang, so we currently program them to be handled on GTI by default.
Beignet can immediately start taking advantage of this change to
enable L3 atomics. Mesa should eventually switch to L3 atomics too,
but a number of non-trivial changes are still required so it will
continue using GTI atomics for now.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
In some cases it might be unnecessary or dangerous to give userspace
the right to write arbitrary values to some register, even though it
might be desirable to give it control of some of its bits. This patch
extends the register whitelist entries to contain a mask/value pair in
addition to the register offset. For registers with non-zero mask,
any LRM writes and LRI writes where the bits of the immediate given by
the mask don't match the specified value will be rejected.
This will be used in my next patch to grant userspace partial write
access to some sensitive registers.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Until now the software command checker assumed that commands could
read or write at most a single register per packet. This is not
necessarily the case, MI_LOAD_REGISTER_IMM expects a variable-length
list of offset/value pairs and writes them in sequence. The previous
code would only check whether the first entry was valid, effectively
allowing userspace to write unrestricted registers of the MMIO space
by sending a multi-register write with a legal first register, with
potential security implications on Gen6 and 7 hardware.
Fix it by extending the drm_i915_cmd_descriptor table to represent
multi-register access and making validate_cmd() iterate for all
register offsets present in the command packet.
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Zhigang Gong <zhigang.gong@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Switch from using 31 PFI credits to 63 PFI credits when cdclk>=czclk on
CHV. The spec lists both 31 and 63 as "suggested" values, but based on
feedback from hardware folks we should actually be using 63. Originally
I picked the 31 basically by flipping a coin.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fixes the resume from suspend-to-ram on the IBM X30
laptop. The problem is caused by the Bios missing to re-initialize
the iVCH registers, especially the PLL registers.
This patch records the iVCH registers during initialization, and
re-installs this register set when resuming.
Signed-off-by: Thomas Richter <thor@math.tu-berlin.de>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
We are always allocating a single page. No need to be verbose so
remove the suffix.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Free the scratch page if dma mapping fails.
Signed-off-by: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The divider value to convert from CZ clock rate to ms needs a +1
adjustment on VLV just like on CHV. This matches both the spec and
the accuracy test by pm_rc6_residency.
v2:
- simplify logic checking for the CHV 320MHz special case (Rodrigo)
Testcase: igt/pm_rc6_residency
Signed-off-by: Imre Deak <imre.deak@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=76877
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we're forgetting to double the port clock when using double
clocked modes with 12bpc on HDMI. We're only accounting for the 1.5x
factor due to the 12bpc. So further double the 1.5x port clock when we
have a double clocked mode.
Unfortunately I don't have any displays that support both 12bpc and
double clocked modes, so I was unable to test this.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Account for the pixel multiplier when reading out the HDMI
mode dotclock. Makes the state checked happier on my ILK when using
double clocked modes.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Check that the DIP is enabled on the right port on IBX and VLV/CHV as
we're doing on g4x, and also check for all the infoframe enable bits on
all platforms.
Eventually we should track each infoframe type independently, and also
their contents. This is a small step in that direction as .infoframe_enabled()
return value could be easily turned into a bitmask.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Currently we just disable the GCP infoframe when turning off the port.
That means if the same transcoder is used on a DP port next, we might
end up pushing infoframes over DP, which isn't intended. Just disable
all the infoframes when turning off the port.
Also protect against two ports stomping on each other on g4x due to
the single video DIP instance. Now only the first port to enable
gets to send infoframes.
v2: Rebase
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Follow the procedure listed in Bspec to toggle the port enable bit off
and on when enabling HDMI with 12bpc and pixel repeat on IBX. The old
code didn't actually enable the port before "toggling" the bit back off,
so the whole workaround was essentially a nop.
Also take the opportunity to clarify the code by splitting the gmch
platforms to a separate (much more straightforward) function.
v2: Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
IBX BSpec says we must specify 8bpc in TRANSCONF for both 8bpc
and 12bpc HDMI output. Do so.
v2: Pass intel_crtc to intel_pipe_has_type()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
When the video timings are suitably aligned so that all different
periods start at phase 0 (ie. none of the periods start mid-pixel)
we can inform the sink about this. Supposedly the sink can then
optimize certain things. Obviously this is only relevant when
outputting >8bpc data since otherwise there are no mid-pixel phases.
v2: Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
GCP infoframes are required to inform the HDMI sink about the color
depth.
Send the GCP infoframe whenever the sink supports any deep color modes
since such sinks must anyway be capable of receiving them. For sinks
that don't support deep color let's skip the GCP in case it might
confuse the sink, although HDMI 1.4 spec does say all sinks must be
capable of reciving them. In theory we could skip the GCP infoframe
for deep color sinks in 8bpc mode as well since sinks must fall back to
8bpc whenever GCP isn't received for some time.
BSpec says we should disable GCP after disabling the port, so do that as
well.
v2: s/intel_set_gcp_infoframe/intel_hdmi_set_gcp_infoframe/
Rebased due to crtc->config changes
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict with lack of chv phy patches and fixup typo
Chandra spotted.]
Reviewed-by: Chandra Konduru <Chandra.konduru@intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Apparently we can have requests even if though the active list is empty,
so do the request retirement regardless of whether there's anything
on the active list.
The way it happened here is that during suspend intel_ring_idle()
notices the olr hanging around and then proceeds to get rid of it by
adding a request. However since there was nothing on the active lists
i915_gem_retire_requests() didn't clean those up, and so the idle work
never runs, and we leave the GPU "busy" during suspend resulting in a
WARN later.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
CPT/PPT require a specific procedure for enabling 12bpc HDMI. Implement
it, and to keep things neat pull the code into a function.
v2: Rebased due to crtc->config changes
s/HDMI_GC/HDMIUNIT_GC/ to match spec better
Factor out intel_enable_hdmi_audio()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ander Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-By: Chandra Konduru <Chandra.konduru@intel.com>
Testecase: igt/kms_render/*
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Fix warnings related to size_t when building for 64-bit architectures:
drivers/gpu/drm/drm_gem_cma_helper.c: In function ‘drm_gem_cma_create’:
drivers/gpu/drm/drm_gem_cma_helper.c:114:4: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t’ [-Wformat=]
size);
^
drivers/gpu/drm/drm_gem_cma_helper.c: In function ‘drm_gem_cma_describe’:
drivers/gpu/drm/drm_gem_cma_helper.c:393:4: warning: format ‘%d’ expects argument of type ‘int’, but argument 8 has type ‘size_t’ [-Wformat=]
off, &cma_obj->paddr, cma_obj->vaddr, obj->size);
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Moving rotation property to "Drm" and removing from i915 and omap.
Also, adding description to the property
Cc: DRI Development <dri-devel@lists.freedesktop.org>
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Sonika Jindal <sonika.jindal@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Rework the crtc event/flip_wait system as follows:
- If we enable a crtc (full modeset), we set omap_crtc->pending and
register vblank irq.
- If we need to set GO bit (page flip), we do the same but also set the
GO bit.
- On vblank we unregister the irq, clear the 'pending' flag, send vblank
event to userspace if crtc->state->event != NULL, and wake up
'pending_wait' wq.
- In omap_atomic_complete() we wait for the 'pending' flag to get reset
for all enabled crtcs using 'pending_wait' wq.
The above ensures that we send the events to userspace in vblank, and
that after the wait in omap_atomic_complete() everything for the
affected crtcs has been completed.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_crtc_atomic_flush() is the only user of omap_crtc_flush(), so just
move the code from omap_crtc_flush() to omap_crtc_atomic_flush().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Before atomic modesetting omap_framebuffer_pin() and
omap_framebuffer_unpin() were always called with modesetting locks
taken. With atomic modesetting support this is no longer the case, and
we need locking to protect the pin_count and the paddr, as multiple
threads may pin the same fb concurrently.
This patch adds a mutex to struct omap_framebuffer, and uses it in
omap_framebuffer_pin() and omap_framebuffer_unpin().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
omap_plane_atomic_update() calls dispc_ovl_setup(), which can fail (but
shouldn't). To make the code a bit more robust, make sure the plane gets
disabled if dispc_ovl_setup() fails, as otherwise we might get illegal
HW configuration leading to error interrupts.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
At the moment we have omap_plane_setup() function which handles both
enabling (and configuring) and disabling the plane. With atomic
modesetting we have separate hooks for plane enable/config and disable.
This patch moves the code from omap_plane_setup() to
omap_plane_atomic_update() and omap_plane_atomic_disable().
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
With atomic modesetting, omap_plane_setup()'s return value is ignored as
the functions using it cannot fail. dispc_ovl_setup(), called by
omap_plane_setup(), can fail (but shouldn't).
Instead of returning an error from omap_plane_setup() which gets
ignored, return void and use WARN if dispc_ovl_setup() fails.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Planes setup is handled by the DRM core through the atomic helpers,
there's no need to duplicate the code in the CRTC .enable() and
.disable() operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_flush() call in omap_crtc_enable() and omap_crtc_disable()
is a no-op, as the display manager is always disabled at this point. Just
remove the function call.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Now that the driver is fully converted to atomic operations, and that
the atomic helpers call the operations in the right order, we can move
encoder setup to where it belongs, in the encoder operations.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Instead of sprinkling dispc_runtime_get() and dispc_runtime_put() calls
in various CRTC operations, move all power management code to the atomic
commit function.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_encoder_setup() function is always called with the DSS
enabled. Remove the dispc_runtime_get() and dispc_runtime_put() calls.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
DRM page flip vblank events requested by page flips or atomic commits
are created by the DRM core and then passed to driver through CRTC
states (for atomic commit) or directly to the page flip handler (for
legacy page flips). The events are then kept aside until the page flip
completes, at which point drivers queue them for delivery with a call to
drm_send_vblank_event().
When a DRM file handle is closed events pending for delivery are cleaned
up automatically by the DRM core. Events that have been passed to the
driver but haven't completed yet, however, are not handled by the DRM
core. Drivers are responsible for destroying them and must not attempt
to queue them for delivery. This is usually handled by drivers'
preclose() handlers that cancel and destroy page flip events that
reference the file handle being closed.
With asynchronous atomic updates the story becomes more complex. Several
asynchronous atomic updates can be pending, each of them carrying
per-CRTC events. As the atomic_commit() operation doesn't receive a file
handle context, drivers can't know which file handle a pending update
refers to, making it difficult to cancel or wait for completion of
updates related to the file handle being closed.
It should be noted that cancelling page flips or waiting for atomic
updates completion isn't required by the DRM core when closing a file
handle. The only requirement is that no event gets queued for delivery
after the preclose() operation returns. This can easily be achieved by
storing events for atomic commits in a list, unlinking events from the
file handle being closed by setting the file_priv field to NULL, and
skipping delivery of unlinked events.
This logic replaces the page flip cancellation completely.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
When performing asynchronous atomic updates the modeset lock isn't taken
around the callers of omap_crtc_flush(). This isn't an issue though, as
access to the CRTC is properly serialized. Just drop the warning.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The omap_crtc_flush() function is always called with a reference to the
dispc held. Remove unnecessary calls to dispc_runtime_get() and
dispc_runtime_put().
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
