In standard form, each state is saved in the xsave area in fixed offset.
But in compacted form, offset of each saved state only can be calculated during
run time because some xstates may not be enabled and saved.
We define kernel API get_xsave_addr() returns address of a given state saved in a xsave area.
It can be called in kernel to get address of each xstate in xsave area in
either standard format or compacted format.
It's useful when kernel wants to directly access each state in xsave area.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Link: http://lkml.kernel.org/r/1401387164-43416-17-git-send-email-fenghua.yu@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Mike reported that commit 7d1a9417 ("x86: Use generic idle loop")
regressed several workloads and caused excessive reschedule
interrupts.
The patch in question failed to notice that the x86 code had an
inverted sense of the polling state versus the new generic code (x86:
default polling, generic: default !polling).
Fix the two prominent x86 mwait based idle drivers and introduce a few
new generic polling helpers (fixing the wrong smp_mb__after_clear_bit
usage).
Also switch the idle routines to using tif_need_resched() which is an
immediate TIF_NEED_RESCHED test as opposed to need_resched which will
end up being slightly different.
Reported-by: Mike Galbraith <bitbucket@online.de>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Cc: lenb@kernel.org
Cc: tglx@linutronix.de
Link: http://lkml.kernel.org/n/tip-nc03imb0etuefmzybzj7sprf@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The __cpuinit type of throwaway sections might have made sense
some time ago when RAM was more constrained, but now the savings
do not offset the cost and complications. For example, the fix in
commit 5e427ec2d0 ("x86: Fix bit corruption at CPU resume time")
is a good example of the nasty type of bugs that can be created
with improper use of the various __init prefixes.
After a discussion on LKML[1] it was decided that cpuinit should go
the way of devinit and be phased out. Once all the users are gone,
we can then finally remove the macros themselves from linux/init.h.
Note that some harmless section mismatch warnings may result, since
notify_cpu_starting() and cpu_up() are arch independent (kernel/cpu.c)
are flagged as __cpuinit -- so if we remove the __cpuinit from
arch specific callers, we will also get section mismatch warnings.
As an intermediate step, we intend to turn the linux/init.h cpuinit
content into no-ops as early as possible, since that will get rid
of these warnings. In any case, they are temporary and harmless.
This removes all the arch/x86 uses of the __cpuinit macros from
all C files. x86 only had the one __CPUINIT used in assembly files,
and it wasn't paired off with a .previous or a __FINIT, so we can
delete it directly w/o any corresponding additional change there.
[1] https://lkml.org/lkml/2013/5/20/589
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: x86@kernel.org
Acked-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Moving x86 to the generic idle implementation (commit 7d1a9417 "x86:
Use generic idle loop") wreckaged the stack protector.
I stupidly missed that boot_init_stack_canary() must be inlined from a
function which never returns, but I put that call into
arch_cpu_idle_prepare() which of course returns.
I pondered to play tricks with arch_cpu_idle_prepare() first, but then
I noticed, that the other archs which have implemented the
stackprotector (ARM and SH) do not initialize the canary for the
non-boot cpus.
So I decided to move the boot_init_stack_canary() call into
cpu_startup_entry() ifdeffed with an CONFIG_X86 for now. This #ifdef
is just a temporary measure as I don't want to inflict the
boot_init_stack_canary() call on ARM and SH that late in the cycle.
I'll queue a patch for 3.11 which removes the #ifdef if the ARM/SH
maintainers have no objection.
Reported-by: Wouter van Kesteren <woutershep@gmail.com>
Cc: x86@kernel.org
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core code expects the arch idle code to return with interrupts
enabled. The conversion missed two x86 cases which fail to do that.
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Borislav Petkov <bp@alien8.de>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1305021557030.3972@ionos
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
show_regs() is inherently arch-dependent but it does make sense to print
generic debug information and some archs already do albeit in slightly
different forms. This patch introduces a generic function to print debug
information from show_regs() so that different archs print out the same
information and it's much easier to modify what's printed.
show_regs_print_info() prints out the same debug info as dump_stack()
does plus task and thread_info pointers.
* Archs which didn't print debug info now do.
alpha, arc, blackfin, c6x, cris, frv, h8300, hexagon, ia64, m32r,
metag, microblaze, mn10300, openrisc, parisc, score, sh64, sparc,
um, xtensa
* Already prints debug info. Replaced with show_regs_print_info().
The printed information is superset of what used to be there.
arm, arm64, avr32, mips, powerpc, sh32, tile, unicore32, x86
* s390 is special in that it used to print arch-specific information
along with generic debug info. Heiko and Martin think that the
arch-specific extra isn't worth keeping s390 specfic implementation.
Converted to use the generic version.
Note that now all archs print the debug info before actual register
dumps.
An example BUG() dump follows.
kernel BUG at /work/os/work/kernel/workqueue.c:4841!
invalid opcode: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.9.0-rc1-work+ #7
Hardware name: empty empty/S3992, BIOS 080011 10/26/2007
task: ffff88007c85e040 ti: ffff88007c860000 task.ti: ffff88007c860000
RIP: 0010:[<ffffffff8234a07e>] [<ffffffff8234a07e>] init_workqueues+0x4/0x6
RSP: 0000:ffff88007c861ec8 EFLAGS: 00010246
RAX: ffff88007c861fd8 RBX: ffffffff824466a8 RCX: 0000000000000001
RDX: 0000000000000046 RSI: 0000000000000001 RDI: ffffffff8234a07a
RBP: ffff88007c861ec8 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000000 R12: ffffffff8234a07a
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS: 0000000000000000(0000) GS:ffff88007dc00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: ffff88015f7ff000 CR3: 00000000021f1000 CR4: 00000000000007f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Stack:
ffff88007c861ef8 ffffffff81000312 ffffffff824466a8 ffff88007c85e650
0000000000000003 0000000000000000 ffff88007c861f38 ffffffff82335e5d
ffff88007c862080 ffffffff8223d8c0 ffff88007c862080 ffffffff81c47760
Call Trace:
[<ffffffff81000312>] do_one_initcall+0x122/0x170
[<ffffffff82335e5d>] kernel_init_freeable+0x9b/0x1c8
[<ffffffff81c47760>] ? rest_init+0x140/0x140
[<ffffffff81c4776e>] kernel_init+0xe/0xf0
[<ffffffff81c6be9c>] ret_from_fork+0x7c/0xb0
[<ffffffff81c47760>] ? rest_init+0x140/0x140
...
v2: Typo fix in x86-32.
v3: CPU number dropped from show_regs_print_info() as
dump_stack_print_info() has been updated to print it. s390
specific implementation dropped as requested by s390 maintainers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Chris Metcalf <cmetcalf@tilera.com> [tile bits]
Acked-by: Richard Kuo <rkuo@codeaurora.org> [hexagon bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert AMD erratum 400 to the bug infrastructure. Then, retract all
exports for modules since they're not needed now and make the AMD
erratum checking machinery local to amd.c. Use forward declarations to
avoid shuffling too much code around needlessly.
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: http://lkml.kernel.org/r/1363788448-31325-7-git-send-email-bp@alien8.de
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
(pm_idle)() is being removed from linux/pm.h
because Linux does not have such a cross-architecture concept.
x86 uses an idle function pointer in its architecture
specific code as a backup to cpuidle. So we re-name
x86 use of pm_idle to x86_idle, and make it static to x86.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
Update APM to register its local idle routine with cpuidle.
This allows us to stop exporting pm_idle to modules on x86.
The Kconfig sub-option, APM_CPU_IDLE, now depends on on CPU_IDLE.
Compile-tested only.
Signed-off-by: Len Brown <len.brown@intel.com>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Jiri Kosina <jkosina@suse.cz>
Remove 32-bit x86 a cmdline param "no-hlt",
and the cpuinfo_x86.hlt_works_ok that it sets.
If a user wants to avoid HLT, then "idle=poll"
is much more useful, as it avoids invocation of HLT
in idle, while "no-hlt" failed to do so.
Indeed, hlt_works_ok was consulted in only 3 places.
First, in /proc/cpuinfo where "hlt_bug yes"
would be printed if and only if the user booted
the system with "no-hlt" -- as there was no other code
to set that flag.
Second, check_hlt() would not invoke halt() if "no-hlt"
were on the cmdline.
Third, it was consulted in stop_this_cpu(), which is invoked
by native_machine_halt()/reboot_interrupt()/smp_stop_nmi_callback() --
all cases where the machine is being shutdown/reset.
The flag was not consulted in the more frequently invoked
play_dead()/hlt_play_dead() used in processor offline and suspend.
Since Linux-3.0 there has been a run-time notice upon "no-hlt" invocations
indicating that it would be removed in 2012.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
mwait_idle() is a C1-only idle loop intended to be more efficient
than HLT, starting on Pentium-4 HT-enabled processors.
But mwait_idle() has been replaced by the more general
mwait_idle_with_hints(), which handles both C1 and deeper C-states.
ACPI processor_idle and intel_idle use only mwait_idle_with_hints(),
and no longer use mwait_idle().
Here we simplify the x86 native idle code by removing mwait_idle(),
and the "idle=mwait" bootparam used to invoke it.
Since Linux 3.0 there has been a boot-time warning when "idle=mwait"
was invoked saying it would be removed in 2012. This removal
was also noted in the (now removed:-) feature-removal-schedule.txt.
After this change, kernels configured with
(CONFIG_ACPI=n && CONFIG_INTEL_IDLE=n) when run on hardware
that supports MWAIT will simply use HLT. If MWAIT is desired
on those systems, cpuidle and the cpuidle drivers above
can be enabled.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
This macro is only invoked by Xen,
so make its definition specific to Xen.
> set_pm_idle_to_default()
< xen_set_default_idle()
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: xen-devel@lists.xensource.com
The text in Documentation said it would be removed in 2.6.41;
the text in the Kconfig said removal in the 3.1 release. Either
way you look at it, we are well past both, so push it off a cliff.
Note that the POWER_CSTATE and the POWER_PSTATE are part of the
legacy tracing API. Remove all tracepoints which use these flags.
As can be seen from context, most already have a trace entry via
trace_cpu_idle anyways.
Also, the cpufreq/cpufreq.c PSTATE one is actually unpaired, as
compared to the CSTATE ones which all have a clear start/stop.
As part of this, the trace_power_frequency also becomes orphaned,
so it too is deleted.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Pull big execve/kernel_thread/fork unification series from Al Viro:
"All architectures are converted to new model. Quite a bit of that
stuff is actually shared with architecture trees; in such cases it's
literally shared branch pulled by both, not a cherry-pick.
A lot of ugliness and black magic is gone (-3KLoC total in this one):
- kernel_thread()/kernel_execve()/sys_execve() redesign.
We don't do syscalls from kernel anymore for either kernel_thread()
or kernel_execve():
kernel_thread() is essentially clone(2) with callback run before we
return to userland, the callbacks either never return or do
successful do_execve() before returning.
kernel_execve() is a wrapper for do_execve() - it doesn't need to
do transition to user mode anymore.
As a result kernel_thread() and kernel_execve() are
arch-independent now - they live in kernel/fork.c and fs/exec.c
resp. sys_execve() is also in fs/exec.c and it's completely
architecture-independent.
- daemonize() is gone, along with its parts in fs/*.c
- struct pt_regs * is no longer passed to do_fork/copy_process/
copy_thread/do_execve/search_binary_handler/->load_binary/do_coredump.
- sys_fork()/sys_vfork()/sys_clone() unified; some architectures
still need wrappers (ones with callee-saved registers not saved in
pt_regs on syscall entry), but the main part of those suckers is in
kernel/fork.c now."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (113 commits)
do_coredump(): get rid of pt_regs argument
print_fatal_signal(): get rid of pt_regs argument
ptrace_signal(): get rid of unused arguments
get rid of ptrace_signal_deliver() arguments
new helper: signal_pt_regs()
unify default ptrace_signal_deliver
flagday: kill pt_regs argument of do_fork()
death to idle_regs()
don't pass regs to copy_process()
flagday: don't pass regs to copy_thread()
bfin: switch to generic vfork, get rid of pointless wrappers
xtensa: switch to generic clone()
openrisc: switch to use of generic fork and clone
unicore32: switch to generic clone(2)
score: switch to generic fork/vfork/clone
c6x: sanitize copy_thread(), get rid of clone(2) wrapper, switch to generic clone()
take sys_fork/sys_vfork/sys_clone prototypes to linux/syscalls.h
mn10300: switch to generic fork/vfork/clone
h8300: switch to generic fork/vfork/clone
tile: switch to generic clone()
...
Conflicts:
arch/microblaze/include/asm/Kbuild
The hlt_use_halt function returns always true and there is only
one definition of it.
The default_idle function can then get ride of the if ...
statement and we can remove the else branch.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: linaro-dev@lists.linaro.org
Cc: patches@linaro.org
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1351181591-8710-1-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull generic execve() changes from Al Viro:
"This introduces the generic kernel_thread() and kernel_execve()
functions, and switches x86, arm, alpha, um and s390 over to them."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/signal: (26 commits)
s390: convert to generic kernel_execve()
s390: switch to generic kernel_thread()
s390: fold kernel_thread_helper() into ret_from_fork()
s390: fold execve_tail() into start_thread(), convert to generic sys_execve()
um: switch to generic kernel_thread()
x86, um/x86: switch to generic sys_execve and kernel_execve
x86: split ret_from_fork
alpha: introduce ret_from_kernel_execve(), switch to generic kernel_execve()
alpha: switch to generic kernel_thread()
alpha: switch to generic sys_execve()
arm: get rid of execve wrapper, switch to generic execve() implementation
arm: optimized current_pt_regs()
arm: introduce ret_from_kernel_execve(), switch to generic kernel_execve()
arm: split ret_from_fork, simplify kernel_thread() [based on patch by rmk]
generic sys_execve()
generic kernel_execve()
new helper: current_pt_regs()
preparation for generic kernel_thread()
um: kill thread->forking
um: let signal_delivered() do SIGTRAP on singlestepping into handler
...
32bit wrapper is lost on that; 64bit one is *not*, since
we need to arrange for full pt_regs on stack when we call
sys_execve() and we need to load callee-saved ones from
there afterwards.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
TIF_NOTIFY_RESUME will work in precisely the same way; all that
is achieved by TIF_IRET is appearing that there's some work to be
done, so we end up on the iret exit path. Just use NOTIFY_RESUME.
And for execve() do that in 32bit start_thread(), not sys_execve()
itself.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Decouple non-lazy/eager fpu restore policy from the existence of the xsave
feature. Introduce a synthetic CPUID flag to represent the eagerfpu
policy. "eagerfpu=on" boot paramter will enable the policy.
Requested-by: H. Peter Anvin <hpa@zytor.com>
Requested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1347300665-6209-2-git-send-email-suresh.b.siddha@intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Fundamental model of the current Linux kernel is to lazily init and
restore FPU instead of restoring the task state during context switch.
This changes that fundamental lazy model to the non-lazy model for
the processors supporting xsave feature.
Reasons driving this model change are:
i. Newer processors support optimized state save/restore using xsaveopt and
xrstor by tracking the INIT state and MODIFIED state during context-switch.
This is faster than modifying the cr0.TS bit which has serializing semantics.
ii. Newer glibc versions use SSE for some of the optimized copy/clear routines.
With certain workloads (like boot, kernel-compilation etc), application
completes its work with in the first 5 task switches, thus taking upto 5 #DNA
traps with the kernel not getting a chance to apply the above mentioned
pre-load heuristic.
iii. Some xstate features (like AMD's LWP feature) don't honor the cr0.TS bit
and thus will not work correctly in the presence of lazy restore. Non-lazy
state restore is needed for enabling such features.
Some data on a two socket SNB system:
* Saved 20K DNA exceptions during boot on a two socket SNB system.
* Saved 50K DNA exceptions during kernel-compilation workload.
* Improved throughput of the AVX based checksumming function inside the
kernel by ~15% as xsave/xrstor is faster than the serializing clts/stts
pair.
Also now kernel_fpu_begin/end() relies on the patched
alternative instructions. So move check_fpu() which uses the
kernel_fpu_begin/end() after alternative_instructions().
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1345842782-24175-7-git-send-email-suresh.b.siddha@intel.com
Merge 32-bit boot fix from,
Link: http://lkml.kernel.org/r/1347300665-6209-4-git-send-email-suresh.b.siddha@intel.com
Cc: Jim Kukunas <james.t.kukunas@linux.intel.com>
Cc: NeilBrown <neilb@suse.de>
Cc: Avi Kivity <avi@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Currently for x86 and x86_32 binaries, fpstate in the user sigframe is copied
to/from the fpstate in the task struct.
And in the case of signal delivery for x86_64 binaries, if the fpstate is live
in the CPU registers, then the live state is copied directly to the user
sigframe. Otherwise fpstate in the task struct is copied to the user sigframe.
During restore, fpstate in the user sigframe is restored directly to the live
CPU registers.
Historically, different code paths led to different bugs. For example,
x86_64 code path was not preemption safe till recently. Also there is lot
of code duplication for support of new features like xsave etc.
Unify signal handling code paths for x86 and x86_64 kernels.
New strategy is as follows:
Signal delivery: Both for 32/64-bit frames, align the core math frame area to
64bytes as needed by xsave (this where the main fpu/extended state gets copied
to and excludes the legacy compatibility fsave header for the 32-bit [f]xsave
frames). If the state is live, copy the register state directly to the user
frame. If not live, copy the state in the thread struct to the user frame. And
for 32-bit [f]xsave frames, construct the fsave header separately before
the actual [f]xsave area.
Signal return: As the 32-bit frames with [f]xstate has an additional
'fsave' header, copy everything back from the user sigframe to the
fpstate in the task structure and reconstruct the fxstate from the 'fsave'
header (Also user passed pointers may not be correctly aligned for
any attempt to directly restore any partial state). At the next fpstate usage,
everything will be restored to the live CPU registers.
For all the 64-bit frames and the 32-bit fsave frame, restore the state from
the user sigframe directly to the live CPU registers. 64-bit signals always
restored the math frame directly, so we can expect the math frame pointer
to be correctly aligned. For 32-bit fsave frames, there are no alignment
requirements, so we can restore the state directly.
"lat_sig catch" microbenchmark numbers (for x86, x86_64, x86_32 binaries) are
with in the noise range with this change.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1343171129-2747-4-git-send-email-suresh.b.siddha@intel.com
[ Merged in compilation fix ]
Link: http://lkml.kernel.org/r/1344544736.8326.17.camel@sbsiddha-desk.sc.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Use a more current logging style:
- Bare printks should have a KERN_<LEVEL> for consistency's sake
- Add pr_fmt where appropriate
- Neaten some macro definitions
- Convert some Ok output to OK
- Use "%s: ", __func__ in pr_fmt for summit
- Convert some printks to pr_<level>
Message output is not identical in all cases.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: levinsasha928@gmail.com
Link: http://lkml.kernel.org/r/1337655007.24226.10.camel@joe2Laptop
[ merged two similar patches, tidied up the changelog ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull fpu state cleanups from Ingo Molnar:
"This tree streamlines further aspects of FPU handling by eliminating
the prepare_to_copy() complication and moving that logic to
arch_dup_task_struct().
It also fixes the FPU dumps in threaded core dumps, removes and old
(and now invalid) assumption plus micro-optimizes the exit path by
avoiding an FPU save for dead tasks."
Fixed up trivial add-add conflict in arch/sh/kernel/process.c that came
in because we now do the FPU handling in arch_dup_task_struct() rather
than the legacy (and now gone) prepare_to_copy().
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, fpu: drop the fpu state during thread exit
x86, xsave: remove thread_has_fpu() bug check in __sanitize_i387_state()
coredump: ensure the fpu state is flushed for proper multi-threaded core dump
fork: move the real prepare_to_copy() users to arch_dup_task_struct()
Pull scheduler changes from Ingo Molnar:
"The biggest change is the cleanup/simplification of the load-balancer:
instead of the current practice of architectures twiddling scheduler
internal data structures and providing the scheduler domains in
colorfully inconsistent ways, we now have generic scheduler code in
kernel/sched/core.c:sched_init_numa() that looks at the architecture's
node_distance() parameters and (while not fully trusting it) deducts a
NUMA topology from it.
This inevitably changes balancing behavior - hopefully for the better.
There are various smaller optimizations, cleanups and fixlets as well"
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Taint kernel with TAINT_WARN after sleep-in-atomic bug
sched: Remove stale power aware scheduling remnants and dysfunctional knobs
sched/debug: Fix printing large integers on 32-bit platforms
sched/fair: Improve the ->group_imb logic
sched/nohz: Fix rq->cpu_load[] calculations
sched/numa: Don't scale the imbalance
sched/fair: Revert sched-domain iteration breakage
sched/x86: Rewrite set_cpu_sibling_map()
sched/numa: Fix the new NUMA topology bits
sched/numa: Rewrite the CONFIG_NUMA sched domain support
sched/fair: Propagate 'struct lb_env' usage into find_busiest_group
sched/fair: Add some serialization to the sched_domain load-balance walk
sched/fair: Let minimally loaded cpu balance the group
sched: Change rq->nr_running to unsigned int
x86/numa: Check for nonsensical topologies on real hw as well
x86/numa: Hard partition cpu topology masks on node boundaries
x86/numa: Allow specifying node_distance() for numa=fake
x86/sched: Make mwait_usable() heed to "idle=" kernel parameters properly
sched: Update documentation and comments
sched_rt: Avoid unnecessary dequeue and enqueue of pushable tasks in set_cpus_allowed_rt()
Pull percpu updates from Tejun Heo:
"Contains Alex Shi's three patches to remove percpu_xxx() which overlap
with this_cpu_xxx(). There shouldn't be any functional change."
* 'for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu:
percpu: remove percpu_xxx() functions
x86: replace percpu_xxx funcs with this_cpu_xxx
net: replace percpu_xxx funcs with this_cpu_xxx or __this_cpu_xxx
There is no need to save any active fpu state to the task structure
memory if the task is dead. Just drop the state instead.
For example, this saved some 1770 xsave's during the system boot
of a two socket Xeon system.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1336692811-30576-4-git-send-email-suresh.b.siddha@intel.com
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Historical prepare_to_copy() is mostly a no-op, duplicated for majority of
the architectures and the rest following the x86 model of flushing the extended
register state like fpu there.
Remove it and use the arch_dup_task_struct() instead.
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/1336692811-30576-1-git-send-email-suresh.b.siddha@intel.com
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Chris Zankel <chris@zankel.net>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Mark Salter <msalter@redhat.com>
Cc: Aurelien Jacquiot <a-jacquiot@ti.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Richard Kuo <rkuo@codeaurora.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Jonas Bonn <jonas@southpole.se>
Cc: James E.J. Bottomley <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Since percpu_xxx() serial functions are duplicated with this_cpu_xxx().
Removing percpu_xxx() definition and replacing them by this_cpu_xxx()
in code. There is no function change in this patch, just preparation for
later percpu_xxx serial function removing.
On x86 machine the this_cpu_xxx() serial functions are same as
__this_cpu_xxx() without no unnecessary premmpt enable/disable.
Thanks for Stephen Rothwell, he found and fixed a i386 build error in
the patch.
Also thanks for Andrew Morton, he kept updating the patchset in Linus'
tree.
Signed-off-by: Alex Shi <alex.shi@intel.com>
Acked-by: Christoph Lameter <cl@gentwo.org>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
What was called show_registers() so far already showed a stack
trace for kernel faults, and kernel_stack_pointer() isn't even
valid to be used for faults from user mode, hence it was
pointless for show_regs() to call show_trace() after
show_registers().
Simply rename show_registers() to show_regs() and eliminate
the old definition.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/r/4FAA3D3902000078000826E1@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The only difference is the free_thread_info function, which frees
xstate.
Use the new arch_release_task_struct() function instead and switch
over to the core allocator.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20120505150141.559556763@linutronix.de
Cc: x86@kernel.org
The checks that exist in mwait_usable() for "idle=" kernel
parameters are insufficient. As a result, mwait_usable() can
return 1 even if "idle=nomwait" or "idle=poll" or "idle=halt"
parameters are passed.
Of these cases, incorrect handling of idle=nomwait is a
universal problem since mwait can get used for usual CPU idling.
However the rest of the cases are problematic only during CPU
Hotplug (offline) because, in the CPU offline path, the function
mwait_play_dead() is called, which might result in mwait being
used in the offline CPUs, if mwait_usable() happens to return 1.
Fix these issues by checking for the boot time "idle=" kernel
parameter properly in mwait_usable().
The first issue (usual cpu idling) is demonstrated below:
Before applying the patch (dmesg snippet):
[ 0.000000] Command line: [...] idle=nomwait
[ 0.000000] Kernel command line: [...] idle=nomwait
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.140606] using mwait in idle threads. <======= mwait being used
[ 4.303986] cpuidle: using governor ladder
[ 4.308232] cpuidle: using governor menu
After applying the patch:
[ 0.000000] Command line: [...] idle=nomwait
[ 0.000000] Kernel command line: [...] idle=nomwait
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 4.264100] cpuidle: using governor ladder
[ 4.268342] cpuidle: using governor menu
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: venki@google.com
Cc: suresh.b.siddha@intel.com
Cc: Borislav Petkov <bp@amd64.org>
Cc: lenb@kernel.org
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Link: http://lkml.kernel.org/r/4F9E37B8.30001@linux.vnet.ibm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Same code. Use the generic version. The special Makefile treatment is
pointless anyway as init_task.o contains only data which is handled by
the linker script. So no point on being treated like head text.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20120503085035.739963562@linutronix.de
Cc: x86@kernel.org
The X86_32-only disable_hlt/enable_hlt mechanism was used by the
32-bit floppy driver. Its effect was to replace the use of the
HLT instruction inside default_idle() with cpu_relax() - essentially
it turned off the use of HLT.
This workaround was commented in the code as:
"disable hlt during certain critical i/o operations"
"This halt magic was a workaround for ancient floppy DMA
wreckage. It should be safe to remove."
H. Peter Anvin additionally adds:
"To the best of my knowledge, no-hlt only existed because of
flaky power distributions on 386/486 systems which were sold to
run DOS. Since DOS did no power management of any kind,
including HLT, the power draw was fairly uniform; when exposed
to the much hhigher noise levels you got when Linux used HLT
caused some of these systems to fail.
They were by far in the minority even back then."
Alan Cox further says:
"Also for the Cyrix 5510 which tended to go castors up if a HLT
occurred during a DMA cycle and on a few other boxes HLT during
DMA tended to go astray.
Do we care ? I doubt it. The 5510 was pretty obscure, the 5520
fixed it, the 5530 is probably the oldest still in any kind of
use."
So, let's finally drop this.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Stephen Hemminger <shemminger@vyatta.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/n/tip-3rhk9bzf0x9rljkv488tloib@git.kernel.org
[ If anyone cares then alternative instruction patching could be
used to replace HLT with a one-byte NOP instruction. Much simpler. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86 updates from Ingo Molnar.
This touches some non-x86 files due to the sanitized INLINE_SPIN_UNLOCK
config usage.
Fixed up trivial conflicts due to just header include changes (removing
headers due to cpu_idle() merge clashing with the <asm/system.h> split).
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/apic/amd: Be more verbose about LVT offset assignments
x86, tls: Off by one limit check
x86/ioapic: Add io_apic_ops driver layer to allow interception
x86/olpc: Add debugfs interface for EC commands
x86: Merge the x86_32 and x86_64 cpu_idle() functions
x86/kconfig: Remove CONFIG_TR=y from the defconfigs
x86: Stop recursive fault in print_context_stack after stack overflow
x86/io_apic: Move and reenable irq only when CONFIG_GENERIC_PENDING_IRQ=y
x86/apic: Add separate apic_id_valid() functions for selected apic drivers
locking/kconfig: Simplify INLINE_SPIN_UNLOCK usage
x86/kconfig: Update defconfigs
x86: Fix excessive MSR print out when show_msr is not specified
Both functions are mostly identical.
The differences are:
- x86_32's cpu_idle() makes use of check_pgt_cache(), which is a
nop on both x86_32 and x86_64.
- x86_64's cpu_idle() uses enter/__exit_idle/(), on x86_32 these
function are a nop.
- In contrast to x86_32, x86_64 calls rcu_idle_enter/exit() in
the innermost loop because idle notifications need RCU.
Calling these function on x86_32 also in the innermost loop
does not hurt.
So we can merge both functions.
Signed-off-by: Richard Weinberger <richard@nod.at>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: paulmck@linux.vnet.ibm.com
Cc: josh@joshtriplett.org
Cc: tj@kernel.org
Link: http://lkml.kernel.org/r/1332709204-22496-1-git-send-email-richard@nod.at
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull x86/fpu changes from Ingo Molnar.
* 'x86-fpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
i387: Split up <asm/i387.h> into exported and internal interfaces
i387: Uninline the generic FP helpers that we expose to kernel modules
While various modules include <asm/i387.h> to get access to things we
actually *intend* for them to use, most of that header file was really
pretty low-level internal stuff that we really don't want to expose to
others.
So split the header file into two: the small exported interfaces remain
in <asm/i387.h>, while the internal definitions that are only used by
core architecture code are now in <asm/fpu-internal.h>.
The guiding principle for this was to expose functions that we export to
modules, and leave them in <asm/i387.h>, while stuff that is used by
task switching or was marked GPL-only is in <asm/fpu-internal.h>.
The fpu-internal.h file could be further split up too, especially since
arch/x86/kvm/ uses some of the remaining stuff for its module. But that
kvm usage should probably be abstracted out a bit, and at least now the
internal FPU accessor functions are much more contained. Even if it
isn't perhaps as contained as it _could_ be.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/alpine.LFD.2.02.1202211340330.5354@i5.linux-foundation.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
The power and cpuidle tracepoints are called within a rcu_idle_exit()
section, and must be denoted with the _rcuidle() version of the tracepoint.
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The x86_64 kernel pushes the fake kernel stack in
arch/x86/kernel/entry_64.S:FAKE_STACK_FRAME, and
rflags register in it does not conform to the specification.
Although Intel's manual[1] says bit 1 of it shall be set to 1,
this bit is cleared to 0 on pushing the fake stack.
[1] Intel(R) 64 and IA-32 Architectures Software Developer's Manual
Vol.1 3-21 Figure 3-8. EFLAGS Register
If it is not on purpose, it is better to be fixed, because
it can lead some tools misunderstanding the stack frame. For example,
"crash" utility[2] actually detects it and warns you like
below:
RIP: ffffffff8005dfa2 RSP: ffff8104ce0c7f58 RFLAGS: 00000200
[...]
bt: WARNING: possibly bogus exception frame
Signed-off-by: Seiichi Ikarashi <s.ikarashi@jp.fujitsu.com>
Tested-by: Masayoshi MIZUMA <m.mizuma@jp.fujitsu.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
