It's perfectly valid for a connection to an SRP target to have a
request limit of 0, so get rid of the message about it, which can spam
kernel logs even with printk_ratelimit(). Keep a count of such events
in a "zero_req_lim" SCSI host attribute instead, so someone who cares
can look at the statistics.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Handle IB_CM_DREQ_ERROR and IB_CM_DREQ_RECEIVED events from the CM,
instead of just printing "Unhandled CM event". In the case of
DREQ_ERROR, just ignore the event -- a TIMEWAIT_EXIT will be generated
also. For DREQ_RECEIVED, send a DREP in response to shut the
connection down cleanly.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Make the sg_tablesize used by SRP adjustable at module load time via a
module parameter. Calculate the corresponding IU length required to
support this.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow userspace to throttle traffic on a given connection to a target
port by adding "max_cmd_per_lun=xyz" to lower the cmd_per_lun value
set for that scsi_host.
Signed-off-by: Vu Pham <vu@mellanox.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Interrupts will always be enabled in srp_remove_one(), so
spin_lock_irq() can be used instead of spin_lock_irqsave().
Also, the loop takes target->scsi_host->host_lock, so target->state
can just be set to SRP_TARGET_REMOVED witout testing the old value.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The SRP driver never sleeps while holding target_mutex, and it's just
used to protect some simple list operations, so hold times will be
short. So just convert it to a spinlock, which is smaller and faster.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
list_for_each_entry_safe() is used in one place where the list isn't
modified. So just change it to list_for_each_entry().
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
SCAN_WILD_CARD is indeed available from <scsi/scsi.h>, which is
already included. So get rid of private hack.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Create an SRP FMR pool on HCAs that support FMRs, and use FMRs to map
gather/scatter lists that have more than one entry into a single
memory region that appears virtually contiguous to the SRP target
(which is the RDMA initiator).
This patch bails out on FMR mapping for SCSI commands where the
gather/scatter list cannot be mapped into a single FMR because there
are sub-page-sized entries in middle of the list. An unaligned
start or end of the list is OK.
Based on a patch by Vu Pham <vuhuong@mellanox.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When flushing out queued commands after a successful device reset,
make sure that SRP completes the right commands, instead of calling
scsi_done on the command passed into the device reset handler over and
over.
Signed-off-by: Ishai Rabinovitz <ishai@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a reconnection attempt fails, then SRP does two scsi_host_put()s.
This is a historical relic from an earlier version of the driver that
took a reference on the scsi_host before trying to reconnect, so get
rid of the extra scsi_host_put().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Sending a DREQ may fail, for example because the remote target has
already broken the connection. If so, then SRP should not wait for
the disconnection to complete, because it never will.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a SCSI abort completes, or the command completes successfully, then
the driver must remove the command from its queue of pending
commands. Similarly, if a device reset succeeds, then all commands
queued for the given device must be removed from the queue.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a SCSI abort succeeds, then the aborted request should to be
removed from the list of pending requests. This fixes list corruption
after an abort occurs.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The recently merged patch to create a fake scatterlist for non-SG SCSI
commands had a bug: the driver ended up doing dma_unmap_sg() on a
scatterlist scmnd->request_buffer rather than the fake scatter list it
created. Fix this so that the driver unmaps the same thing it maps.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Since the SCSI midlayer is moving towards entirely getting rid of
commands with use_sg == 0, we should treat this case as an exception.
Therefore, change the IB SRP initiator to create a fake scatterlist
for these commands with sg_init_one(). This simplifies the flow of
DMA mapping and unmapping, since SRP can just use dma_map_sg() and
dma_unmap_sg() unconditionally, rather than having to choose between
the dma_{map,unmap}_sg() and dma_{map,unmap}_single() variants.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix leak found by Coverity: in the SRP_OPT_DGID case,
srp_parse_options() didn't free the result of match_strdup().
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add SCSI host attributes in sysfs that show the ID extension, IOC
GUID, service ID, P_Key and destination GID for each target port that
the SRP initiator connects to.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Convert srp_host->target_mutex from a semaphore to a mutex.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a node_guid field to struct ib_device. It is the responsibility
of the low-level driver to initialize this field before registering a
device with the midlayer. Convert everyone to looking at this field
instead of calling ib_query_device() when all they want is the node
GUID, and remove the node_guid field from struct ib_device_attr.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Include fixes for 2.6.14-git11. Should allow to remove sched.h from
module.h on i386, x86_64, arm, ia64, ppc, ppc64, and s390. Probably more
to come since I haven't yet checked the other archs.
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Have __srp_get_tx_iu() fail if the target port's request limit will
not allow the initiator to post a send. This avoids continuing on and
posting a receive, and then failing to post a corresponding send. If
that happens, then the initiator will end up with an extra receive
posted, and if this happens to much, the receive queue will overflow.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Increase SRP max_luns to 512 to match the kernel's default, since SRP
storage targets can have lots of LUNs and the SRP initiator itself
doesn't have any particular limit.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch removes almost all inclusions of linux/version.h. The 3
#defines are unused in most of the touched files.
A few drivers use the simple KERNEL_VERSION(a,b,c) macro, which is
unfortunatly in linux/version.h.
There are also lots of #ifdef for long obsolete kernels, this was not
touched. In a few places, the linux/version.h include was move to where
the LINUX_VERSION_CODE was used.
quilt vi `find * -type f -name "*.[ch]"|xargs grep -El '(UTS_RELEASE|LINUX_VERSION_CODE|KERNEL_VERSION|linux/version.h)'|grep -Ev '(/(boot|coda|drm)/|~$)'`
search pattern:
/UTS_RELEASE\|LINUX_VERSION_CODE\|KERNEL_VERSION\|linux\/\(utsname\|version\).h
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add an InfiniBand SCSI RDMA Protocol (SRP) initiator. This driver is
used to talk talk to InfiniBand SRP targets (storage devices).
Signed-off-by: Roland Dreier <rolandd@cisco.com>