The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:
* tunning off L1 data cache and the MMU
* putting SDRAM into self-refresh
* storing some EMC registers and SCLK burst policy
* switching CPU to CLK_M (12MHz OSC)
* switching SCLK to CLK_S (32KHz OSC)
* tunning off PLLM, PLLP and PLLC
* shutting off the CPU rail
The sequence of LP1 resuming:
* re-enabling PLLM, PLLP, and PLLC
* restoring some EMC registers and SCLK burst policy
* setting up CCLK burst policy to PLLP
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41
Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored, CCLK burst policy be set in PLLP. Then jumping to
"tegra_resume" that was expected to be stored in PMC_SCRATCH41 to restore
CPU context and back to kernel.
Based on the work by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The LP1 suspend mode will power off the CPU, clock gated the PLLs and put
SDRAM to self-refresh mode. Any interrupt can wake up device from LP1. The
sequence when LP1 suspending:
* tunning off L1 data cache and the MMU
* storing some EMC registers, DPD (deep power down) status, clk source of
mselect and SCLK burst policy
* putting SDRAM into self-refresh
* switching CPU to CLK_M (12MHz OSC)
* tunning off PLLM, PLLP, PLLA, PLLC and PLLX
* switching SCLK to CLK_S (32KHz OSC)
* shutting off the CPU rail
The sequence of LP1 resuming:
* re-enabling PLLM, PLLP, PLLA, PLLC and PLLX
* restoring the clk source of mselect and SCLK burst policy
* setting up CCLK burst policy to PLLX
* restoring DPD status and some EMC registers
* resuming SDRAM to normal mode
* jumping to the "tegra_resume" from PMC_SCRATCH41
Due to the SDRAM will be put into self-refresh mode, the low level
procedures of LP1 suspending and resuming should be copied to
TEGRA_IRAM_CODE_AREA (TEGRA_IRAM_BASE + SZ_4K) when suspending. Before
restoring the CPU context when resuming, the SDRAM needs to be switched
back to normal mode. And the PLLs need to be re-enabled, SCLK burst policy
be restored, CCLK burst policy be set in PLLX. Then jumping to
"tegra_resume" that was expected to be stored in PMC_SCRATCH41 to restore
CPU context and back to kernel.
Based on the work by: Scott Williams <scwilliams@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Tegra114 is a quad cores SoC. Each core can be hotplugged including
CPU0. The hotplug sequence can be controlled by setting event trigger in
flow controller. Then the flow controller will take care all the power
sequence that include CPU up and down.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
More multiplatform enablement for ARM platforms. The ones converted in
this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was a
patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=4hSo
-----END PGP SIGNATURE-----
Merge tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC multiplatform updates from Olof Johansson:
"More multiplatform enablement for ARM platforms. The ones converted
in this branch are:
- bcm2835
- cns3xxx
- sirf
- nomadik
- msx
- spear
- tegra
- ux500
We're getting close to having most of them converted!
One of the larger platforms remaining is Samsung Exynos, and there are
a bunch of supporting patches in this merge window for it. There was
a patch in this branch to a early version of multiplatform conversion,
but it ended up being reverted due to need of more bake time. The
revert commit is part of the branch since it would have required
rebasing multiple dependent branches and they were stable by then"
* tag 'multiplatform-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
mmc: sdhci-s3c: Fix operation on non-single image Samsung platforms
clocksource: nomadik-mtu: fix up clocksource/timer
Revert "ARM: exynos: enable multiplatform support"
ARM: SPEAr13xx: Fix typo "ARCH_HAVE_CPUFREQ"
ARM: exynos: enable multiplatform support
rtc: s3c: make header file local
mtd: onenand/samsung: make regs-onenand.h file local
thermal/exynos: remove unnecessary header inclusions
mmc: sdhci-s3c: remove platform dependencies
ARM: samsung: move mfc device definition to s5p-dev-mfc.c
ARM: exynos: move debug-macro.S to include/debug/
ARM: exynos: prepare for sparse IRQ
ARM: exynos: introduce EXYNOS_ATAGS symbol
ARM: tegra: build assembly files with -march=armv7-a
ARM: Push selects for TWD/SCU into machine entries
ARM: ux500: build hotplug.o for ARMv7-a
ARM: ux500: move to multiplatform
ARM: ux500: make remaining headers local
ARM: ux500: make irqs.h local to platform
ARM: ux500: get rid of <mach/[hardware|db8500-regs].h>
...
This branch contains platform updates for 3.10. Among the highlights:
- Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
- New support for CSR SiRFatlas6 SoCs
- A handful of updates for NVidia T114 (a.k.a. Tegra 4)
- A bunch of updates for the shmobile platforms
- A handful of updates for davinci
- A few updates for Qualcomm MSM
- Plus a handful of other patches, defconfig updates, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HXX3
-----END PGP SIGNATURE-----
Merge tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"This branch contains part 1 of the platform updates for 3.10. Among
the highlights:
- Support for the new Atmel Cortex-A5 based platforms (SAMA5D3)
- New support for CSR SiRFatlas6 SoCs
- A handful of updates for NVidia T114 (a.k.a. Tegra 4)
- A bunch of updates for the shmobile platforms
- A handful of updates for davinci
- A few updates for Qualcomm MSM
- Plus a handful of other patches, defconfig updates, etc."
* tag 'soc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (135 commits)
ARM: tegra: pm: fix build error w/o PM_SLEEP
ARM: davinci: ensure global variables are declared
ARM: davinci: sram.c: fix incorrect type in assignment
ARM: davinci: da8xx dt: make file local symbols static
ARM: davinci: da8xx: add remoteproc support
ARM: socfpga: Upgrade clk driver for socfpga to make use of dts clock entries
ARM: socfpga: Add clock entries into device tree
ARM: socfpga: Enable soft reset
ARM: EXYNOS: replace cpumask by the corresponding macro
ARM: EXYNOS: handle properly the return values
ARM: EXYNOS: factor out the idle states
ARM: OMAP4: Enable fix for Cortex-A9 erratas
ARM: OMAP2+: Export SoC information to userspace
ARM: OMAP2+: SoC name and revision unification
ARM: OMAP2+: Move common part of late init into common function
ARM: tegra: pm: remove duplicated include from pm.c
ARM: davinci: da850: override mmc DT node device name
ARM: davinci: da850: add mmc DT entries
mmc: davinci_mmc: add DT support
ARM: SAMSUNG: check processor type before cache restoration in resume
...
Here is a collection of cleanup patches. Among the pieces that stand out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=xCAx
-----END PGP SIGNATURE-----
Merge tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanup from Olof Johansson:
"Here is a collection of cleanup patches. Among the pieces that stand
out are:
- The deletion of h720x platforms
- Split of at91 non-dt platforms to their own Kconfig file to keep
them separate
- General cleanups and refactoring of i.MX and MXS platforms
- Some restructuring of clock tables for OMAP
- Convertion of PMC driver for Tegra to dt-only
- Some renames of sunxi -> sun4i (Allwinner A10)
- ... plus a bunch of other stuff that I haven't mentioned"
* tag 'cleanup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (119 commits)
ARM: i.MX: remove unused ARCH_* configs
ARM i.MX53: remove platform ahci support
ARM: sunxi: Rework the restart code
irqchip: sunxi: Rename sunxi to sun4i
irqchip: sunxi: Make use of the IRQCHIP_DECLARE macro
clocksource: sunxi: Rename sunxi to sun4i
clocksource: sunxi: make use of CLKSRC_OF
clocksource: sunxi: Cleanup the timer code
ARM: at91: remove trailing semicolon from macros
ARM: at91/setup: fix trivial typos
ARM: EXYNOS: remove "config EXYNOS_DEV_DRM"
ARM: EXYNOS: change the name of USB ohci header
ARM: SAMSUNG: Remove unnecessary code for dma
ARM: S3C24XX: Remove unused GPIO drive strength register definitions
ARM: OMAP4+: PM: Restore CPU power state to ON with clockdomain force wakeup method
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2412
ARM: S3C24XX: Removed unneeded dependency on CPU_S3C2410
ARM: S3C24XX: Removed unneeded dependency on ARCH_S3C24XX for boards
ARM: SAMSUNG: Fix typo "CONFIG_SAMSUNG_DEV_RTC"
ARM: S5P64X0: Fix typo "CONFIG_S5P64X0_SETUP_SDHCI"
...
The tegra assembly files are written for ARMv7 and are not compatible
with ARMv6, which leads to build warnings when compiling a dual
ARMv6/v7 kernel. Since this code is only ever run on Tegra ARMv7
hardware, we can tell the assembler which architecture level to
use.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch moves cpufreq driver of ARM based tegra platform to drivers/cpufreq.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add speedo-based process identification for Tegra114.
Based on the work by: Alex Frid <afrid@nvidia.com>
Signed-off-by: Danny Huang <dahuang@nvidia.com>
[swarren: added include of bug.h]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This is the preparation to unify "board-dt-tegra{20,30,114}.c" to a
single file "tegra.c".
Signed-off-by: Hiroshi Doyu <hdoyu@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Adding the generic ARM_CPUIDLE_WFI_STATE support for Tegra114.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The "sleep.S" file has many functions that be shared by different module
currently. Not just for CPU idle driver. Make it build as default now.
Reported-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren: add sleep.o to separate line so each line only contains 1 file]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The reset handler code is used for either UP or SMP. To make Tegra device
can compile for UP. It needs to be moved to another file that is not SMP
only. This is because the reset handler also be needed by CPU idle
"powered-down" mode. So we also need to put the reset handler init function
in non-SMP only and init them always.
And currently the implementation of the reset handler to know which CPU is
OK to bring up was identital with "cpu_present_mask". But the
"cpu_present_mask" did not initialize yet when the reset handler init
function was moved to init early function. We use the "cpu_possible_mask"
to replace "cpu_present_mask". Then it can work on both UP and SMP case.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren: dropped the move of v7_invalidate_l1() from one file to another,
to avoid conflicts with Pavel's cleanup of this function, adjust Makefile
so each line only contains 1 file.]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Move arch/arm/mach-tegra/timer.c to drivers/clocksource/tegra20_timer.c
so that the code is co-located with other clocksource drivers, and to
reduce the size of the mach-tegra directory.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This supports power-gated idle on secondary CPUs for Tegra30. The
secondary CPUs can go into powered-down state independently. When
CPU goes into this state, it saves it's contexts and puts itself
to flow controlled WFI state. After that, it will been power gated.
Be aware of that, you may see the legacy power state "LP2" in the
code which is exactly the same meaning of "CPU power down".
Based on the work by:
Scott Williams <scwilliams@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The different Tegra chips may have different CPU idle states and data.
Individual CPU idle driver make it more easy to maintain.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
For the naming consistency under the mach-tegra, we re-name the file of
"sleep-tXX" to "sleep-tegraXX" (e.g., sleep-t30 to sleep-tegra30).
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
This patch adds speedo-based process identification support for Tegra30.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
[swarren s/Tegra3/Tegra30/ in log print,
s/T30/Tegra30/ in commit description]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Detect CPU and core process ID by checking speedo corner tables.
This can provide a more accurate process ID.
Signed-off-by: Danny Huang <dahuang@nvidia.com>
[swarren s/Tegra2/Tegra20/ in log print]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
A shorter cleanup branch submitted separately due to dependencies with
some of the previous topics.
Major thing here is that the Broadcom bcmring platform is removed. It's an
SoC that's used on some stationary VoIP platforms, and is in desperate
need of some cleanup. Broadcom came back and suggested that we just
deprecate the platform for now, since they aren't going to spend the
resources needed on cleaning it up, and there are no users of the platform
directly from mainline.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=LPF/
-----END PGP SIGNATURE-----
Merge tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc cleanups, part 2 from Olof Johansson:
"A shorter cleanup branch submitted separately due to dependencies with
some of the previous topics.
Major thing here is that the Broadcom bcmring platform is removed.
It's an SoC that's used on some stationary VoIP platforms, and is in
desperate need of some cleanup. Broadcom came back and suggested that
we just deprecate the platform for now, since they aren't going to
spend the resources needed on cleaning it up, and there are no users
of the platform directly from mainline."
Fix some conflicts due to BCM2835 getting added next to the removed
BCMRING, and removal of tegra files that had been converted to
devicetree.
* tag 'cleanup2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: Orion5x: ts78xx: Add IOMEM for virtual addresses.
ARM: ux500: use __iomem pointers for MMIO
ARM: Remove mach-bcmring
ARM: clps711x: Remove board support for CEIVA
ARM: clps711x: Fix register definitions
ARM: clps711x: Fix lowlevel debug-macro
ARM: clps711x: Added simple clock framework
pinctrl: tegra: move pinconf-tegra.h content into drivers/pinctrl
ARM: tegra: delete unused headers
ARM: tegra: remove useless includes of <mach/*.h>
ARM: tegra: remove dead code
Most notable here is probably the addition of basic support for the
BCM2835, an SoC used in some of the Roku 2 players as well as the
much-hyped Raspberry Pi, cleaned up and contributed by Stephen
Warren. It's still early days on mainline support, with just the
basics working. But it has to start somewhere!
Beyond that there's some conversions of clock infrastructure on tegra
to common clock, misc updates for several other platforms, and OMAP
now has its own bus (under drivers/bus) to manage its devices through.
This branch adds two new directories outside of arch/arm:
drivers/irqchip for new irq controllers, and drivers/bus for the above
OMAP bus. It's expected that some of the other platforms will migrate
parts of their platforms to those directories over time as well.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BCp4
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc-specific updates from Olof Johansson:
"Most notable here is probably the addition of basic support for the
BCM2835, an SoC used in some of the Roku 2 players as well as the
much-hyped Raspberry Pi, cleaned up and contributed by Stephen Warren.
It's still early days on mainline support, with just the basics
working. But it has to start somewhere!
Beyond that there's some conversions of clock infrastructure on tegra
to common clock, misc updates for several other platforms, and OMAP
now has its own bus (under drivers/bus) to manage its devices through.
This branch adds two new directories outside of arch/arm:
drivers/irqchip for new irq controllers, and drivers/bus for the above
OMAP bus. It's expected that some of the other platforms will migrate
parts of their platforms to those directories over time as well."
Fix up trivial conflicts with the clk infrastructure changes.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (62 commits)
ARM: shmobile: add new __iomem annotation for new code
ARM: LPC32xx: Support GPI 28
ARM: LPC32xx: Platform update for devicetree completion of spi-pl022
ARM: LPC32xx: Board cleanup
irqchip: fill in empty Kconfig
ARM: SAMSUNG: Add check for NULL in clock interface
ARM: EXYNOS: Put PCM, Slimbus, Spdif clocks to off state
ARM: EXYNOS: Add bus clock for FIMD
ARM: SAMSUNG: Fix HDMI related warnings
ARM: S3C24XX: Add .get_rate callback for "camif-upll" clock
ARM: EXYNOS: Fix incorrect help text
ARM: EXYNOS: Turn off clocks for NAND, OneNAND and TSI controllers
ARM: OMAP: AM33xx hwmod: fixup SPI after platform_data move
MAINTAINERS: add an entry for the BCM2835 ARM sub-architecture
ARM: bcm2835: instantiate console UART
ARM: bcm2835: add stub clock driver
ARM: bcm2835: add system timer
ARM: bcm2835: add interrupt controller driver
ARM: add infra-structure for BCM2835 and Raspberry Pi
ARM: tegra20: add CPU hotplug support
...
This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used with
a mainline kernel. We have not been able to find anyone interested
in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=ck1u
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM soc general cleanups from Olof Johansson:
"This is a large branch that contains a handful of different cleanups:
- Fixing up the I/O space remapping on PCI on ARM. This is a series
from Rob Herring that restructures how all pci devices allocate I/O
space, and it's part of the work to allow multiplatform kernels.
- A number of cleanup series for OMAP, moving and removing some
headers, sparse irq rework and in general preparation for
multiplatform.
- Final removal of all non-DT boards for Tegra, it is now
device-tree-only!
- Removal of a stale platform, nxp4008. It's an old mobile chipset
that is no longer in use, and was very likely never really used
with a mainline kernel. We have not been able to find anyone
interested in keeping it around in the kernel.
- Removal of the legacy dmaengine driver on tegra
+ A handful of other things that I haven't described above."
Fix up some conflicts with the staging tree (and because nxp4008 was
removed)
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (184 commits)
ARM: OMAP2+: serial: Change MAX_HSUART_PORTS to 6
ARM: OMAP4: twl-common: Support for additional devices on i2c1 bus
ARM: mmp: using for_each_set_bit to simplify the code
ARM: tegra: harmony: fix ldo7 regulator-name
ARM: OMAP2+: Make omap4-keypad.h local
ARM: OMAP2+: Make l4_3xxx.h local
ARM: OMAP2+: Make l4_2xxx.h local
ARM: OMAP2+: Make l3_3xxx.h local
ARM: OMAP2+: Make l3_2xxx.h local
ARM: OMAP1: Move irda.h from plat to mach
ARM: OMAP2+: Make hdq1w.h local
ARM: OMAP2+: Make gpmc-smsc911x.h local
ARM: OMAP2+: Make gpmc-smc91x.h local
ARM: OMAP1: Move flash.h from plat to mach
ARM: OMAP2+: Make debug-devices.h local
ARM: OMAP1: Move board-voiceblue.h from plat to mach
ARM: OMAP1: Move board-sx1.h from plat to mach
ARM: OMAP2+: Make omap-wakeupgen.h local
ARM: OMAP2+: Make omap-secure.h local
ARM: OMAP2+: Make ctrl_module_wkup_44xx.h local
...
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
The branch is based on v3.6-rc6 in order to pick up a bug-fix to the
ASoC Tegra PCM driver that's required for audio to work correctly when
using dmaengine.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=4eRL
-----END PGP SIGNATURE-----
Merge tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra into next/cleanup
ARM: tegra: switch to dmaengine
The Tegra code-base has contained both a legacy DMA and a dmaengine
driver since v3.6-rcX. This series flips Tegra's defconfig to enable
dmaengine rather than the legacy driver, and removes the legacy driver
and all client code.
* tag 'tegra-for-3.7-dmaengine' of git://git.kernel.org/pub/scm/linux/kernel/git/swarren/linux-tegra:
ASoC: tegra: remove support of legacy DMA driver based access
spi: tegra: remove support of legacy DMA driver based access
ARM: tegra: apbio: remove support of legacy DMA driver based access
ARM: tegra: dma: remove legacy APB DMA driver
ARM: tegra: config: enable dmaengine based APB DMA driver
+ sync to 3.6-rc6
Remove the legacy APB dma driver. The APB DMA support
is moved to dmaengine based Tegra APB DMA driver.
All clients are also moved to dmaengine based APB DMA
driver.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now that all boards are converted to device tree, devices.[ch] and
board-pinmux.[ch] are no longer used. So, remove them.
The only exception is the EHCI platform data in devices.h. Move that
data to board-dt-tegra20.c - the only places it's used.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Harmony uses a TPS6586x regulator. Instantiate this, and hook up a
couple of fixed GPIO-controlled regulators too.
Based on Ventana regulator patch by Stephen Warren <swarren@nvidia.com>
and converted to Harmony.
swarren made the following changes:
* Added ldo0 regulator configuration to device tree, and updated
board-harmony-pcie.c for the new regulator name.
* Fixed vdd_1v05's voltage from 10.5V to 1.05V.
* Modified board-harmony-pcie.c to obtain the en_vdd_1v05 GPIO number at
run-time from device tree instead of hard-coding it.
* Removed board-harmony{-power.c,.h} now that they're unused.
* Disabled vdd_1v05 regulator; the code in board-harmony-pcie.c hijacks
this GPIO for now. This will be fixed when the PCIe driver is re-
written as a driver. The code can't regulator_get("vdd_1v05") right
now, because the vdd_1v05 regulator's probe gets deferred due to its
supply being the PMIC, which gets probed after the regulator the first
time around, and this dependency is only resolved by repeated probing,
which happens when deferred_probe_initcall() is called, which happens
in a late initcall, whose runtime order relative to harmony_pcie_init()
is undefined, since that's also called from a late initcall.
* Removed unused harmony_pcie_initcall().
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Harmony can be booted using device tree with equal functionality as when
booted using a board file. Remove as much of the board file as is
possible, since it's no longer needed.
Two special-cases are still left in board-dt-tegra20.c, since the Tegra
PCIe driver doesn't support device tree yet, and the Harmony .dts file
doesn't yet describe regulators which are needed for PCIe. This logic is
now enabled unconditionally rather than via CONFIG_MACH_HARMONY. While
this is more code than other boards, it's still unlikely to be much of a
problem, and both regulators and PCIe should be supported via device tree
in the near future, allowing the remaining code to be removed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Paz00 (Toshiba AC100) can be booted using device tree with equal
functionality as when booted using a board file. Remove as much of the
board file as is possible, since it's no longer needed.
One special-case is still left in board-dt-tegra20.c, since there is no
way to create a WiFi rfkill device from device tree yet. This logic is
now enabled unconditionally rather than via CONFIG_MACH_PAZ00. The extra
cases where it's enabled (.configs which did not enable Paz00 support)
shouldn't impact much since the amount of code is tiny.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Marc Dietrich <marvin24@gmx.de>
TrimSlice can be booted using device tree with equal functionality as
when booted using a board file. Remove the board file since it's no
longer needed.
One special-case is still left in board-dt-tegra20.c, since the Tegra
PCIe driver doesn't support device tree yet. This logic is now enabled
by CONFIG_TEGRA_PCI rather than via CONFIG_MACH_TRIMSLICE. The extra
cases where it's enabled (.configs which did not enable TrimSlice
support) shouldn't impact much since the amount of code is tiny.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Hotplug function put CPU in offline or online mode at runtime.
When the CPU been put into offline, it was been clock gated. The
offline CPU can be power gated, when the remaining CPU goes into
LP2.
Based on the worked by:
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Hotplug function put CPUs in offline or online state at runtime.
When the CPU been put in the offline state, it was been clock and
power gated. Except primary CPU other CPUs can be hotplugged.
Based on the work by:
Scott Williams <scwilliams@nvidia.com>
Colin Cross <ccross@android.com>
Gary King <gking@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Make the name consistent with other files.
s/tegra2/tegra20
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Move clock initialization data to separate file. This is
required for migrating to generic clock framework if static
initialization is used.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Move clock initialization data to separate file. This is
required for migrating to generic clock framework if static
initialization is used.
Signed-off-by: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
As part of this patch:
1. Moved existing tegra phy driver to drivers/USB directory.
2. Added standard USB phy driver APIs to tegra phy driver.
Signed-off-by: Venu Byravarasu <vbyravarasu@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
These changes are all for individual board files. In the long run, those
files will largely go away, and the amount of changes appears to be
continuously decreasing, which is a good sign. This time around, changes
are focused on tegra, omap and samsung.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUAUA2dfmCrR//JCVInAQLsaw//az90mZ0Tub0UO01D0uIJORBwD9JsMTQM
W3/L3FEByskB+ZbJ6HG6XEYIzbJZxN49RbXOl0DGOuqfAlAGO61jVMaSkOKsqMCz
WoLxaMZFOB7UBCGD+dvJYriirnS3OwFbCJ0Zn1xvBnpsYC2qavhorpvIXcYHh/mK
v1zBNuDWVeedKsjYQWEAI2O1kCRuFa0P91YlmdKA3pQ9kKoA/WORHVA2i8Ou+5Mc
5Yu1JQCxfJPFA0HA612zdj8bbQbqanlKgGlm7dYJ9lLSZBnQolrVMnLhVhl5wf8d
YWlJsDdSyrbIY/HFd2xul4kWGZSg1PoKDFNwBDHoBBzdR25kXmER92PuskpwBeDo
Nv56W7Hx2q7tob1woG5kE1tZFlE1cCT/MCVoLGDwpZnFJE0pBA1Hua15mB829k2y
2vnXjRIM3j020cMC9Qa9/6aFgQu5ojCvHTuKBEwFX4zxZGGrYStINhE8jg4MXI9Y
NOaqo1MP2X84T7ONuWaiJv6MyluhdGofbzWyxVU7Af+im6N8M3Lezmw8mMfsXwiw
URHHOKnBmbkQxAUKWq+G7xr+Ti5JxLkCSUrJffJSkXPOBojKnaAegRBxexM9NhTB
Y6NPt0zKxiJqyFpW4WZ8+29GP6RbwRhoeUNyI88i3RQwa3pwHAOiExZ3q86no9rO
ONQe3uLFr3k=
=nKn1
-----END PGP SIGNATURE-----
Merge tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc board specific updates from Arnd Bergmann:
"These changes are all for individual board files. In the long run,
those files will largely go away, and the amount of changes appears to
be continuously decreasing, which is a good sign. This time around,
changes are focused on tegra, omap and samsung."
Fix conflicts in arch/arm/mach-{omap2/common-board-devices.c,tegra/Makefile.boot}
as per the 'for-linus' branch.
* tag 'boards' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
ARM: EXYNOS: Add leds status1 and status2 on Origen board
ARM: S3C64XX: Mark most Cragganmore initdata devinitdata
ARM: EXYNOS: Add missing .reserve field to SMDKC210
ARM: EXYNOS: Add DRM device to SMDK4X12 board
ARM: S3C64XX: Clean up after SPI driver platform data updates
ARM: SAMSUNG: no need to set the value for clk_xusbxti when it is 24Mhz
ARM: EXYNOS: Add framebuffer support for SMDK4X12
ARM: EXYNOS: Add HSOTG support to SMDK4X12
ARM: S5PV210: Add audio platform device in Goni board
ARM: S5PV210: Add audio platform device in Aquila board
ARM: EXYNOS: Add audio platform device in SMDKV310 board
ARM: S3C64XX: Don't specify an irq_base for WM1192-EV1 board
ARM: OMAP3: Fix omap3evm randconfig error introduced by VBUS support
ARM: OMAP: board-omap4panda: MUX configuration for sys_nirq2
ARM: OMAP: board-4430sdp: MUX configuration for sys_nirq2
ARM: OMAP3530evm: set pendown_state and debounce time for ads7846
ARM: omap3evm: enable VBUS switch for EHCI tranceiver
ARM: OMAP3EVM: Adding USB internal LDOs board file
ARM: OMAP3EVM: Add NAND flash definition
ARM: OMAP3: cm-t35: add tvp5150 decoder support
...
This is stuff that does not fit well into another category and in
particular is not related to a particular board. The largest part
in here is extending the am33xx support in the omap platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Qclg
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific updates from Arnd Bergmann:
"This is stuff that does not fit well into another category and in
particular is not related to a particular board. The largest part in
here is extending the am33xx support in the omap platform."
Fix up trivial conflicts in arch/arm/mach-{imx/mach-mx35_3ds.c, tegra/Makefile}
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (74 commits)
ARM: LPC32xx: Add PWM support
ARM: LPC32xx: Add PWM clock
ARM: LPC32xx: Set system serial based on cpu unique id
ARM: vexpress: Config option for early printk console
ARM: vexpress: Add Device Tree for V2P-CA15_CA7 core tile
ARM: vexpress: Convert V2P-CA15 Device Tree to 64 bit addresses
ARM: vexpress: Add fixed regulator for SMSC
ARM: vexpress: Add missing SP804 interrupt in motherboard's DTS files
ARM: vexpress: Initial common clock support
ARM: SAMSUNG: Introduce Kconfig variable for Samsung custom clk API
ARM: EXYNOS: Add missing static storage class specifier in pmu.c file
ARM: EXYNOS: Make combiner_init function static
ARM: EXYNOS: Update HSOTG PHY clock setting for EXYNOS4X12
ARM: versatile: Make plat-versatile clock optional
ARM: vexpress: Check master site in daughterboard's sysctl operations
ARM: vexpress: remove automatic errata workaround selection
ARM: LPC32xx: Adjust to pl08x DMA interface changes
ARM: EXYNOS: Clear SYS_WDTRESET bit to use watchdog reset
ARM: imx: fix mx51 ehci setup errors
ARM: imx: make ehci power/oc polarities configurable
...
The Tegra20 HW issue with accessing APBIO registers (such
as fuse registers) directly from the CPU concurrently with
APB DMA accesses has been fixed in Tegra30 and later chips.
Access these registers directly from the CPU on Tegra30
and later, and apply the workaround only for Tegra20.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Tested-by: Chaitanya Bandi <bandik@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The Seaboard device tree supports all the features that the Seaboard
board files support. Hence, there's no need to keep the board files
around any more; all users should convert to device tree.
MACH_KAEN and MACH_WARIO are also removed. While tegra-seaboard.dts
doesn't support those explicitly, it would be trivial to create device
trees for those boards if anyone cares.
The Seaboard device tree is now compiled if Tegra2 support is enabled,
rather than when Seaboard support is enabled.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
* Make ARCH_TEGRA select USE_OF; DT is the way forward.
* Build board-dt-tegra*.c when the relevant Tegra SoC support is enabled,
rather than requiring a specific config option for this.
* The board-specific config options already build board-*-pinmux.o, and
when booting from device tree these files are no longer needed, so we
can remove some Makefile commands related to those files.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
powergate functions are needed for tegra30 as well (see common.c), so
build it always. Fixes:
arch/arm/mach-tegra/built-in.o: In function `tegra30_init_early':
apbio.c:(.init.text+0x78): undefined reference to `tegra_powergate_init'
(using "allnoconfig" with tegra30 enabled)
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The pinctrl driver is now active and used by all boards. Remove the
old pinmux driver.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
This branch contains a handful of updates of SoC base code that had
dependencies on other external trees that have now been merged:
* Support for the new EXYNOS5250 SoC from Samsung
* SMP and power domain support for Tegra3 from NVIDIA
* ux500 updates for exporting SoC information through sysfs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPcpwnAAoJEIwa5zzehBx3RIQP/AvTVHF7EIXfu5XGLBYeKW+U
HBeT1kO1qL8m3gA/+DG/JzNpd8JDlILGob6hUN4lqA8f49MBkmttdbATZvBj4Nx+
T4+louPteiueexJdolj6hVCuNBhFJLgik3zMKGHvL8wbvqYHKpfqvuWWuzxtP3Hl
F1BvFSrQ5TZALGtNiRWDMwxFa2oA03ZNXjy+v9i3GIdn1vH18/IDryz7/7MW6GPv
NuKmZkcEpX2jDFe3AkqUMLxqMYizfuGg20FlV4tmxiF5Wlht6EiN38Y56LZgwuly
mde6AWN8qgwTYDk4cJ5ZVJtwkowosF5ko57V3SPmVaVc/WajZ0v28gt9YgNLVPL7
TXFEUJgIxzJnyM+DoSltzQ9tCsWUscQGmyPt4QSOLO2D76/3z+8+24/EwAIM/7Bj
u5/+74k5jDBZe1suCt/1P1Vr3l5Z3os483R7y4BtyLtWtQvBcjpkITj9lHmnsAf3
RqN2Z4osLcILwWVKa2y2DCOeJm0jvSCsn53+O3FGTSqhfwWTUVkqaDALeGXwJGbH
2rMks18BqJ2sT2ruFXHiVvZOj/8XxkcLsq8ztnuYoHQssrNtAtBM97l/xi1V7L0z
FmXnPszVA1mIkelsY2VDImEks/Iaad4o3Iuba9Yr3OKOSr/d8kLyB0reTmS/SHQL
u/o8ch/V5QVEo/H+ud7K
=X89H
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: More SoC support updates" from Olof Johansson:
"This branch contains a handful of updates of SoC base code that had
dependencies on other external trees that have now been merged:
* Support for the new EXYNOS5250 SoC from Samsung
* SMP and power domain support for Tegra3 from NVIDIA
* ux500 updates for exporting SoC information through sysfs"
Fix up trivial merge conflicts as per Olof.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (30 commits)
ARM: mach-shmobile: ap4evb: Reserve DMA memory for the frame buffer
ARM: EXYNOS: Fix compilation error with mach-exynos4-dt board
ARM: dts: add initial dts file for EXYNOS5250, SMDK5250
ARM: EXYNOS: add support device tree enabled board file for EXYNOS5
ARM: EXYNOS: add support ARCH_EXYNOS5 for EXYNOS5 SoCs
ARM: EXYNOS: add support get_core_count() for EXYNOS5250
ARM: EXYNOS: support EINT for EXYNOS4 and EXYNOS5
ARM: EXYNOS: add interrupt definitions for EXYNOS5250
ARM: EXYNOS: add support for EXYNOS5250 SoC
ARM: EXYNOS: add support uart for EXYNOS4 and EXYNOS5
ARM: EXYNOS: add initial setup-i2c0 for EXYNOS5
ARM: EXYNOS: add clock part for EXYNOS5250 SoC
ARM: EXYNOS: use exynos_init_uarts() instead of exynos4_init_uarts()
ARM: EXYNOS: to declare static for mach-exynos/common.c
ARM: EXYNOS: Add clkdev lookup entry for lcd clock
ARM: dt: Explicitly configure all serial ports on Tegra Cardhu
ARM: tegra: support for secondary cores on Tegra30
ARM: tegra: support for Tegra30 CPU powerdomains
ARM: tegra: add support for Tegra30 powerdomains
ARM: tegra: export tegra_powergate_is_powered()
...
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
These changes are all specific to an soc family or the code for
one soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later in
the merge window for stuff that has dependencies on external trees or
that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly because
of changes regarding localtimer.c, which was removed in the end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WdYR
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: SoC specific updates" from Arnd Bergmann:
"These changes are all specific to an soc family or the code for one
soc. Lots of work for Tegra3 this time, but also a lot of other
platforms. There will be another (smaller) set of soc patches later
in the merge window for stuff that has dependencies on external trees
or that was sent just before the merge window opened.
The asoc tree added a few devices to the i.mx platform, which conflict
with other devices added in the same place here.
The tegra Makefile conflicts between a number of branches, mostly
because of changes regarding localtimer.c, which was removed in the
end.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fix up some trivial conflicts, including the mentioned Tegra Makefile.
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (51 commits)
ARM: EXYNOS: fix cycle count for periodic mode of clock event timers
ARM: EXYNOS: add support JPEG
ARM: EXYNOS: Add DMC1, allow PPMU access for DMC
ARM: SAMSUNG: Correct MIPI-CSIS io memory resource definition
ARM: SAMSUNG: fix __init attribute on regarding s3c_set_platdata()
ARM: SAMSUNG: Add __init attribute to samsung_bl_set()
ARM: S5PV210: Add usb otg phy control
ARM: S3C64XX: Add usb otg phy control
ARM: EXYNOS: Enable l2 configuration through device tree
ARM: EXYNOS: remove useless code to save/restore L2
ARM: EXYNOS: save L2 settings during bootup
ARM: S5P: add L2 early resume code
ARM: EXYNOS: Add support AFTR mode on EXYNOS4210
ARM: mx35: Setup the AIPS registers
ARM: mx5: Use common function for configuring AIPS
ARM: mx3: Setup AIPS registers
ARM: mx3: Let mx31 and mx35 enter in LPM mode in WFI
ARM: defconfig: imx_v6_v7: build in REGULATOR_FIXED_VOLTAGE
ARM: imx: update imx_v6_v7_defconfig
ARM: tegra: Demote EMC clock inconsistency BUG to WARN
...
