This converts the Cadence SPI master driver to use GPIO
descriptors for chip select handling.
The Cadence driver was allocating a state container just
to hold the requested GPIO line and contained lots of
polarity inversion code. As this is all handled by gpiolib
and a simple devm_* request in the core, and as the driver
is fully device tree only, most of this code chunk goes
away in favour of central handling. The setup/cleanup
callbacks goes away.
This driver does NOT drive the CS line by setting the
value of the GPIO so it relies on the SPI core to do
this, which should work just fine with the descriptors.
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Cc: Janek Kotas <jank@cadence.com>
Cc: Linuxarm <linuxarm@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the Atmel SPI master driver to use GPIO descriptors
for chip select handling.
The Atmel driver has duplicate code to look up and initialize CS
GPIOs from the device tree, so this is removed. It further has code
to retrieve a CS GPIO from .controller_data but this seems to be
completely unused in the kernel (legacy codepath?) so I deleted
this support. It keeps track of polarity when switching the CS, but
this is not needed anymore since we moved this over to the gpiolib.
The local handling of the "npcs_pin" (I guess this might mean
"negative polarity chip select pin") is preserved, but I strongly
suspect this can be switched over to handling by the core and
using the SPI_MASTER_GPIO_SS flag on the master to assure that
the additional CS handling in the driver is also done.
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Radu Pirea <radu.pirea@microchip.com>
Cc: Linuxarm <linuxarm@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This converts the ATH79 SPI master driver to use GPIO descriptors
for chip select handling.
The ATH79 driver was requesting the GPIO and driving it from the
bitbang .chipselect callback. Do not request it anymore as the SPI
core will request it, remove the line inversion semantics for the
GPIO case (handled by gpiolib) and let the SPI core deal with
requesting the GPIO line from the device tree node of the controller.
This driver can be instantiated from a board file (no device tree)
but the board files only use native CS (no GPIO lines) so we should
be fine just letting the SPI core grab the GPIO from the device.
The fact that the driver is actively driving the GPIO in the
ath79_spi_chipselect() callback is confusing since the host does
not set SPI_MASTER_GPIO_SS so this should not ever get called when
using GPIO CS. I put in a comment about this.
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Alban Bedel <albeu@free.fr>
Cc: Linuxarm <linuxarm@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This augments the SPI core to optionally use GPIO descriptors
for chip select on a per-master-driver opt-in basis.
Drivers using this will rely on the SPI core to look up
GPIO descriptors associated with the device, such as
when using device tree or board files with GPIO descriptor
tables.
When getting descriptors from the device tree, this will in
turn activate the code in gpiolib that was
added in commit 6953c57ab1
("gpio: of: Handle SPI chipselect legacy bindings")
which means that these descriptors are aware of the active
low semantics that is the default for SPI CS GPIO lines
and we can assume that all of these are "active high" and
thus assign SPI_CS_HIGH to all CS lines on the DT path.
The previously used gpio_set_value() would call down into
gpiod_set_raw_value() and ignore the polarity inversion
semantics.
It seems like many drivers go to great lengths to set up the
CS GPIO line as non-asserted, respecting SPI_CS_HIGH. We pull
this out of the SPI drivers and into the core, and by simply
requesting the line as GPIOD_OUT_LOW when retrieveing it from
the device and relying on the gpiolib to handle any inversion
semantics. This way a lot of code can be simplified and
removed in each converted driver.
The end goal after dealing with each driver in turn, is to
delete the non-descriptor path (of_spi_register_master() for
example) and let the core deal with only descriptors.
The different SPI drivers have complex interactions with the
core so we cannot simply change them all over, we need to use
a stepwise, bisectable approach so that each driver can be
converted and fixed in isolation.
This patch has the intended side effect of adding support for
ACPI GPIOs as it starts relying on gpiod_get_*() to get
the GPIO handle associated with the device.
Cc: Linuxarm <linuxarm@huawei.com>
Acked-by: Jonathan Cameron <jonathan.cameron@huawei.com>
Tested-by: Fangjian (Turing) <f.fangjian@huawei.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add routines, registers & bitfield definition. Also baud rate divisor
definitions for STM32F4 SPI. This version supports full-duplex,
simplex TX and half-duplex TX communication with 8 or 16-bit per word.
DMA capability is optionally supported for transfer longer than 16 bytes.
For transfer less than 16 bytes frames can be send in discontinuous mode.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prepare support for STM32F4 spi variant by introducing compatible
configuration data.
Move STM32H7 specific stuff to compatible data structure:
- registers & bit fields
- routines to control driver
- baud rate divisor definitions
- fifo availability
- split IRQ functions to parts to be called when the IRQ occurs
and for threaded interrupt what helps to provide less discontinuous
mode for drivers without FIFO.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add transfer_one_dma_start function to be more generic for other
stm32 SPI family drivers.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Split stm32_spi_transfer_one_setup function into smaller chunks
to be more generic for other stm32 SPI family drivers.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Interrupt function is used as a thread so rename it to express
meaning directly by more clear function name.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rename STM32 SPI registers to be related to STM32H7 SPI driver
and not STM32 generally.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver does not support SPI LOOP mode by configuration
in registers.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Driver supports SPI mode 0 to 3 not only the mode 3.
Use SPI_CPOL and SPI_CPHA indicates that these bits
can be changed to obtain modes 0 - 3.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix typo from STMicroelectonics to STMicroelectronics.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When SPI driver is configured to work only with TX or RX DMA channel
then dmaengine functions can dereferene NULL pointer.
Running full-duplex mode when when only RX or TX DMA channel is
available can cause overrun condition or incorrect writing to transmit
buffer so disable this types of DMA configuration and go back to
interrupt mode.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Patch fixes sparse warning: Using plain integer as NULL pointer. Replaces
second argument of function devm_clk_get from 0 to NULL.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Cezary Gapinski <cezary.gapinski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
spi::mode is defined by framework for several SPI capabilities,
such as polarity, phase, bit-endian, wire number. Directly use this
variable for setting controller's polarity and phase causes other
bit in register being set. Since SPI framework has its definition,
SPI_CPOL and SPI_CPHA offset may be changed by framwork change.
Instead of just mask off the relevant bits,
fetch required bit in spi::mode and set to register.
Signed-off-by: shaftarger <shol@livemail.tw>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add some cpu families that are actually using the fsl-dspi module
in the related Kconfig description.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
On ColdFire mcf54418, using DSPI_DMA_MODE mode, spi transfers
at first boot stage are not succeding:
m25p80 spi0.1: unrecognized JEDEC id bytes: 00, 00, 00
The reason is the SPI_SR initial value set by the driver, that
is not clearing (not setting to 1) the RF_DF flag. After a tour
on the dspi hw modules that use this driver(Vybrid, ColdFire and
ls1021a) a better init value for SR register has been set.
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver is derived from the SPI NOR driver at
mtd/spi-nor/fsl-quadspi.c. It uses the new SPI memory interface
of the SPI framework to issue flash memory operations to up to
four connected flash chips (2 buses with 2 CS each).
The controller does not support generic SPI messages.
This patch also disables the build of the "old" driver and reuses
its Kconfig option CONFIG_SPI_FSL_QUADSPI to replace it.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Acked-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Tested-by: Han Xu <han.xu@nxp.com>
Reviewed-by: Boris Brezillon <bbrezillon@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Remove Reset operation in fsl_lpspi_config(). This RST may cause both CLK
and CS pins go from high to low level under cs-gpio mode.
Add fsl_lpspi_reset() function after one message transfer to clear all
flags in use.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add judgment on SR_MBF and FSR_RXCOUNT.
In PIO mode, if don't use CONT to keep cs selected in one transfer, the
transfer will go wrong. FCIE will be set after one frame transfer
finish. If use CONT, the frame refer to the whole data in one transfer.
If don't use CONT, the frame refer to one byte of whole data. This will
cause the transfer ending early.
This patch add a register reading in isr function, it might lead to a
slight decrease in the max transmission speed in PIO mode.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use SR_TDF to judge if need to send data, and SR_FCF is to judge if
transmission end and to replace the waiting after transmission end.
This waiting has no actual meaning, for module will set the FCF
flag at the real end.
The changes of interrupt flag and ISR function reduce the times of
calling ISR. The use of the FCF flag improves the stability of the
data transmission. These two points generally improve the data
transfer speed of lpspi, especially when it is set to slave mode
it can support higher transfer speed of the host.
After making these changes, there is no need to use
fsl_lpspi_txfifo_empty(), so remove it.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In npcm_pspi_probe(), current code set platform_set_drvdata(pdev, master);
so in npcm_pspi_remove() platform_get_drvdata(pdev) will return pointer to
master rather than priv. Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while for
controller features designed to make them perform better but it's not
worked out as well as hoped so the interface has been redesigned in a
way that will hopefully do better - it's already been adopted by a
number of additional controllers so things are looking good. Otherwise
most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris Brezillon
and Yogesh Narayan Gaur plus usage of it in several drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlwhLBsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AGvB/9odNqLjVJiG6v0EIKqLyYXMzCYgmrZ
RyBZoqTKoNmXxv0b/Fdsi8VaiJ8x2WIcqLzhpQlg3twOCvXQbgoA+JzQNyHZlZ1u
8cxfFGebVS6r0k14bkmAVR8LSvGlReOZQLC2MvccVc/UAwN0/p5ncN0xUADHvIOW
/Pmx0/e2uCMx1+OMAudlUXQ5IIbnb5/OjvDfR/7tlVo5YKSgkHBJeunOYSaPSNuO
QNf9+kZxvQ8djYbpYqqHWovPF7JSlQAj0WkMJPB/g3R09E/vatSBlCMnETBJWn/L
wogHquLK/vwRaS+MqTSrGsi0ylpqgxmZrbGKcXKF51fim0EvBg7cMqe6
=ZnI3
-----END PGP SIGNATURE-----
Merge tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The main thing this release has been a lot of work on the integration
with SPI NOR flashes, there's been some specific support for a while
for controller features designed to make them perform better but it's
not worked out as well as hoped so the interface has been redesigned
in a way that will hopefully do better - it's already been adopted by
a number of additional controllers so things are looking good.
Otherwise most of the work has been driver specific:
- Support for better integration with NOR flashes from Boris
Brezillon and Yogesh Narayan Gaur plus usage of it in several
drivers.
- A big cleanup of the Rockchip driver from Emil Renner Berthing.
- Lots of performance improvements for bcm2835 from Lukas Wunner.
- Slave mode support for pxa2xx from Lubomir Rintel.
- Support for Macronix MXIC, Mediatek MT7629 and MT8183, NPCM PSPI,
and Renesas r8a77470"
* tag 'spi-v4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (90 commits)
spi: sh-msiof: Reduce the number of times write to and perform the transmission from FIFO
spi: sh-msiof: Add r8a774c0 support
doc: lpspi: Document DT bindings for LPSPI slave mode
spi: lpspi: Let watermark change with send data length
spi: lpspi: Add slave mode support
spi: lpspi: Replace all "master" with "controller"
spi: imx: drop useless member speed_hz from driver data struct
spi: imx: rename config callback and add useful parameters
spi: imx: style fixes
spi: imx: mx51-ecspi: Move some initialisation to prepare_message hook.
spi: imx: add a device specific prepare_message callback
mtd: atmel-quadspi: disallow building on ebsa110
spi: Update NPCM PSPI controller documentation
spi: npcm: Modify pspi send function
spi: Use of_node_name_eq for node name comparisons
spi: dw-mmio: add ACPI support
spi: bcm2835: Synchronize with callback on DMA termination
spi: bcm2835: Speed up FIFO access if fill level is known
spi: bcm2835: Polish transfer of DMA prologue
spi: spi-mem: add support for octal mode I/O data transfer
...
The current state of the spi-sh-msiof, in master transfer mode: if t-> bits_per_word <= 8,
if the data length is divisible by 4 ((len & 3) = 0), the length of each word will be 32 bits
In case of data length can not be divisible by 4 ((len & 3) != 0), always set each word to be
8 bits, this will increase the number of times that write to FIFO, increasing the number of
times it should be transmitted. Assume that the number of bytes of data length more than 64 bytes,
each transmission will write 64 times into the TFDR then transmit, a maximum one-time
transmission will transmit 64 bytes if each word is 8 bits long.
Switch to setting if t->bits_per_word <= 8, the word length will be 32 bits although the data
length is not divisible by 4, then if leftover, will transmit the balance and the length of each
words is 1 byte. The maximum each can transmit up to 64 x 4 (Data Size = 32 bits (4 bytes)) = 256 bytes.
TMDR2 : Bits 28 to 24 BITLEN1[4:0] Data Size (8 to 32 bits)
Bits 23 to 16 WDLEN1[7:0] Word Count (1 to 64 words)
Signed-off-by: Hoan Nguyen An <na-hoan@jinso.co.jp>
Signed-off-by: Mark Brown <broonie@kernel.org>
Configure watermark to change with the length of the sent data.
Support LPSPI sending message shorter than tx/rxfifosize.
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add slave mode support to the fsl-lpspi driver, only in PIO mode.
For now, there are some limitations for slave mode transmission:
1. The stale data in RXFIFO will be dropped when the Slave does any new
transfer.
2. One transfer can be finished only after all transfer->len data been
transferred to master device
3. Slave device only accepts transfer->len data. Any data longer than
this from master device will be dropped. Any data shorter than this
from master will cause LPSPI to stuck due to mentioned limitation 2.
4. Only PIO transfer is supported in Slave Mode.
Wire connection:
GND, SCK, MISO(to MISO of slave), MOSI(to MOSI of slave), SCS
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to enable the slave mode and make the code more readable,
replace all related structure names and object names which is
named "master" with "controller".
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver data's member variable just caches the transfer's speed_hz
member. All users of the former now have access directly to the latter.
So fix them to use the uncached value and remove the cache.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The config callback is called once per transfer while some things can (and
should) be done on a per message manner. To have unambiguous naming in the
end include "transfer" in the callback's name and rename the
implementations accordingly. Also pass the driver struct and transfer
which allows further simplifications in the following patch.
There is no change in behavior intended here.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change fixes some random style issues that I noticed while debugging
the driver: Remove some double spaces, use tabs for indention instead
of spaces if possible, fix comment style.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The relevant difference between prepare_message and config is that the
former is run before the CS signal is asserted. So the polarity of the
CLK line must be configured in prepare_message as an edge generated by
config might already result in a latch of the MOSI line.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is just preparatory work which allows to move some initialisation
that currently is done in the per transfer hook .config to an earlier
point in time in the next few patches. There is no change in behaviour
introduced by this patch.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
I ran into a link-time error with the atmel-quadspi driver on the
EBSA110 platform:
drivers/mtd/built-in.o: In function `atmel_qspi_run_command':
:(.text+0x1ee3c): undefined reference to `_memcpy_toio'
:(.text+0x1ee48): undefined reference to `_memcpy_fromio'
The problem is that _memcpy_toio/_memcpy_fromio are not available on
that platform, and we have to prevent building the driver there.
In case we want to backport this to older kernels: between linux-4.8
and linux-4.20, the Kconfig entry was in drivers/mtd/spi-nor/Kconfig
but had the same problem.
Link: https://lore.kernel.org/patchwork/patch/812860/
Fixes: 161aaab8a0 ("mtd: atmel-quadspi: add driver for Atmel QSPI controller")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Align pspi send function code with the recieve function
code, Also simplify the code a bit with early return.
Signed-off-by: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Convert string compares of DT node names to use of_node_name_eq helper
instead. This removes direct access to the node name pointer.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Hisilicon Hip08 platform, that uses ACPI, has this controller.
Let's add ACPI support for DW SPI MMIO-based host.
The ACPI ID used is "HISI0173" for the Designware SPI controller of
Hisilicon Hip08 platform.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit b36f09c3c4 ("dmaengine: Add transfer termination
synchronization support") deprecated dmaengine_terminate_all() in favor
of dmaengine_terminate_sync() and dmaengine_terminate_async() to avoid
freeing resources used by the DMA callback before its execution has
concluded.
Commit de92436ac4 ("dmaengine: bcm2835-dma: Use vchan_terminate_vdesc()
instead of desc_free") amended the BCM2835 DMA driver with an
implementation of ->device_synchronize(), which is a prerequisite for
dmaengine_terminate_sync(). Thus, clients of the DMA driver (such as
the BCM2835 SPI driver) may now be converted to the new API.
It is generally desirable to use the _sync() variant except in atomic
context. There is only a single occurrence where the BCM2835 SPI driver
calls dmaengine_terminate_all() in atomic context and that is in
bcm2835_spi_dma_done() (the RX DMA channel's callback) to terminate the
TX DMA channel. The TX DMA channel doesn't have a callback (yet), hence
it is safe to use the _async() variant there.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Cc: Vinod Koul <vkoul@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RX and TX FIFO of the BCM2835 SPI master each accommodate 64 bytes
(16 32-bit dwords). The CS register provides hints on their fill level:
"Bit 19 RXR - RX FIFO needs Reading ([¾] full)
0 = RX FIFO is less than [¾] full (or not active TA = 0).
1 = RX FIFO is [¾] or more full. Cleared by reading sufficient
data from the RX FIFO or setting TA to 0."
"Bit 16 DONE - Transfer Done
0 = Transfer is in progress (or not active TA = 0).
1 = Transfer is complete. Cleared by writing more data to the
TX FIFO or setting TA to 0."
"If DONE is set [...], write up to 16 [dwords] to SPI_FIFO. [...]
If RXR is set read 12 [dwords] data from SPI_FIFO."
[Source: Pages 153, 154 and 158 of
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
Note: The spec is missing the "¾" character, presumably due to
copy-pasting from a different charset. It also incorrectly
refers to 16 and 12 "bytes" instead of 32-bit dwords.]
In short, the RXR bit indicates that 48 bytes can be read and the DONE
bit indicates 64 bytes can be written. Leverage this knowledge to read
or write bytes blindly to the FIFO, without polling whether data can be
read or free space is available to write. Moreover, when a transfer is
starting, the TX FIFO is known to be empty, likewise allowing a blind
write of 64 bytes.
This cuts the number of bus accesses in half if the fill level is known.
Also, the (posted) write accesses can be pipelined on the AXI bus since
they are no longer interleaved with (non-posted) reads.
bcm2835_spi_transfer_one_poll() switches to interrupt mode when a time
limit is exceeded by calling bcm2835_spi_transfer_one_irq(). The TX
FIFO may contain data in this case, but is known to be empty when the
function is called from bcm2835_spi_transfer_one(). Hence only blindly
fill the TX FIFO in the latter case but not the former.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Tested-by: Eric Anholt <eric@anholt.net>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 3bd7f6589f ("spi: bcm2835: Overcome sglist entry length
limitation") was unfortunately merged even though submission of a
refined version was imminent. Apply those refinements as an amendment:
* Drop no longer needed #include <asm/page.h>. The lines requiring
its inclusion were removed by the commit.
* Change type of tx_spillover flag from bool to unsigned int for
consistency with dma_pending flag and pursuant to Linus' dictum:
https://lkml.org/lkml/2017/11/21/384
* In bcm2835_rd_fifo_count() do not check for bs->rx_buf != NULL.
The function will never be called if that's the case.
* Amend kerneldoc of bcm2835_wait_tx_fifo_empty() to prevent its use in
situations where the function might spin forever. (In response to a
review comment by Stefan Wahren.)
* Sync only the cacheline containing the RX prologue back to memory,
not the full first sglist entry.
* Use sg_dma_address() and sg_dma_len() instead of referencing the
sglist entry members directly. Seems to be the more common syntax in
the tree, even for lvalues.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for octal mode I/O data transfer in spi-mem framework.
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add flags for Octal mode I/O data transfer
Required for the SPI controller which can do the data transfer (TX/RX)
on 8 data lines e.g. NXP FlexSPI controller.
SPI_TX_OCTAL: transmit with 8 wires
SPI_RX_OCTAL: receive with 8 wires
Signed-off-by: Yogesh Gaur <yogeshnarayan.gaur@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix build errors when CONFIG_PINCTRL is not enabled.
The header file <linux/pinctrl/consumer.h> handles both CONFIG_PINCTRL
enabled and disabled cases.
CC [M] drivers/spi/spi-at91-usart.o
../drivers/spi/spi-at91-usart.c: In function 'at91_usart_spi_runtime_suspend':
../drivers/spi/spi-at91-usart.c:409:2: error: implicit declaration of function 'pinctrl_pm_select_sleep_state' [-Werror=implicit-function-declaration]
pinctrl_pm_select_sleep_state(dev);
../drivers/spi/spi-at91-usart.c: In function 'at91_usart_spi_runtime_resume':
../drivers/spi/spi-at91-usart.c:419:2: error: implicit declaration of function 'pinctrl_pm_select_default_state' [-Werror=implicit-function-declaration]
pinctrl_pm_select_default_state(dev);
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Radu Pirea <radu.pirea@microchip.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit e82b0b3828 ("spi: bcm2835: Fix race on DMA termination") broke
the build with COMPILE_TEST=y on arches whose cmpxchg() requires 32-bit
operands (xtensa, older arm ISAs).
Fix by changing the dma_pending flag's type from bool to unsigned int.
Fixes: e82b0b3828 ("spi: bcm2835: Fix race on DMA termination")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
A few driver specific fixes here, nothing big or that stands out for
anyone other than the driver users.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlv+uFQTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0GN/B/9rkzlaRTNvBepsN3qbDfFotIt2+9T0
as4tDY5t+C6PWHkKaqezTuKzin+fSOpSQ9n8rx2yc9oddwpelDsqLVxUlxRuN+RB
C+UBfls7rP3J8AlYaGFor+N+MjiRuWVpfYW0PbFf1kM8l1fmOP7FC7BB76G1Ketu
3U9DSWeL5YMZq+IIXI3e77f3luq4/bo2DVxNMQ/PL/frbpRIqOVYag5kGFRxYYez
7rcAo68mOCv/85xdqNZ5u2m+xO/fpSYV+CGFXbYvGPizFIGl9REnw+8DE7EVSCo7
xsPsMuj/bE0Gr3frPguZ0XFsOyFB+SVxqMQxQt2zKiEDuLtQYTFmhs9h
=kDIQ
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few driver specific fixes here, nothing big or that stands out for
anyone other than the driver users.
The omap2-mcspi fix is for issues that started showing up with a
change in defconfig in this release to make cpuidle get turned on by
default"
* tag 'spi-fix-v4.20-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: omap2-mcspi: Add missing suspend and resume calls
spi: mediatek: use correct mata->xfer_len when in fifo transfer
spi: uniphier: fix incorrect property items
When in DMA mode, the BCM2835 SPI controller requires that the FIFO is
accessed in 4 byte chunks. This rule is not fulfilled if a transfer
consists of multiple sglist entries, one per page, and the first entry
starts in the middle of a page with an offset not a multiple of 4.
The driver currently falls back to programmed I/O for such transfers,
incurring a significant performance penalty.
Overcome this hardware limitation by transferring the first few bytes of
a transfer without DMA such that the remainder of the first sglist entry
becomes a multiple of 4. Specifics are provided in kerneldoc comments.
An alternative approach would have been to split transfers in the
->prepare_message hook, but this may necessitate two transfers per page,
defeating the goal of clustering multiple pages together in a single
transfer for efficiency. E.g. if the first TX sglist entry's length is
23 and the first RX's is 40, the first transfer would send and receive
23 bytes, the second 40 - 23 = 17 bytes, the third 4096 - 17 = 4079
bytes, the fourth 4096 - 4079 = 17 bytes and so on. In other words,
O(n) transfers are necessary (n = number of sglist entries), whereas
the algorithm implemented herein only requires O(1) additional work.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document the driver's data structure to lower the barrier to entry for
contributors.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit a30a555d74 ("spi: bcm2835: transform native-cs to gpio-cs on
first spi_setup") disabled the use of hardware-controlled native Chip
Select in favour of software-controlled GPIO Chip Select but left code
to support the former untouched. Remove it to simplify the driver and
ease the addition of new features and further optimizations.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If a DMA transfer finishes orderly right when spi_transfer_one_message()
determines that it has timed out, the callbacks bcm2835_spi_dma_done()
and bcm2835_spi_handle_err() race to call dmaengine_terminate_all(),
potentially leading to double termination.
Prevent by atomically changing the dma_pending flag before calling
dmaengine_terminate_all().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Fixes: 3ecd37edaa ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Cc: stable@vger.kernel.org # v4.2+
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If submission of a DMA TX transfer succeeds but submission of the
corresponding RX transfer does not, the BCM2835 SPI driver terminates
the TX transfer but neglects to reset the dma_pending flag to false.
Thus, if the next transfer uses interrupt mode (because it is shorter
than BCM2835_SPI_DMA_MIN_LENGTH) and runs into a timeout,
dmaengine_terminate_all() will be called both for TX (once more) and
for RX (which was never started in the first place). Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Fixes: 3ecd37edaa ("spi: bcm2835: enable dma modes for transfers meeting certain conditions")
Cc: stable@vger.kernel.org # v4.2+
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The IRQ handler bcm2835_spi_interrupt() first reads as much as possible
from the RX FIFO, then writes as much as possible to the TX FIFO.
Afterwards it decides whether the transfer is finished by checking if
the TX FIFO is empty.
If very few bytes were written to the TX FIFO, they may already have
been transmitted by the time the FIFO's emptiness is checked. As a
result, the transfer will be declared finished and the chip will be
reset without reading the corresponding received bytes from the RX FIFO.
The odds of this happening increase with a high clock frequency (such
that the TX FIFO drains quickly) and either passing "threadirqs" on the
command line or enabling CONFIG_PREEMPT_RT_BASE (such that the IRQ
handler may be preempted between filling the TX FIFO and checking its
emptiness).
Fix by instead checking whether rx_len has reached zero, which means
that the transfer has been received in full. This is also more
efficient as it avoids one bus read access per interrupt. Note that
bcm2835_spi_transfer_one_poll() likewise uses rx_len to determine
whether the transfer has finished.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Fixes: e34ff011c7 ("spi: bcm2835: move to the transfer_one driver model")
Cc: stable@vger.kernel.org # v4.1+
Cc: Mathias Duckeck <m.duckeck@kunbus.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Martin Sperl <kernel@martin.sperl.org>
Cc: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch implements power management callback function for USART as
SPI driver.
Signed-off-by: Radu Pirea <radu_nicolae.pirea@upb.ro>
Signed-off-by: Mark Brown <broonie@kernel.org>
The compiler has no way to know that rsize 1 or 2 are the only valid
values. Also simplify the code a bit with early return.
The warning was:
drivers/spi/spi-npcm-pspi.c:215:6: warning: 'val' may be used uninitialized in this function [-Wmaybe-uninitialized]
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
There is an IS_ERR() vs PTR_ERR() typo here. The current code returns 1
but we want to return the negative error code.
Fixes: 2a22f1b30c ("spi: npcm: add NPCM PSPI controller driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Address remaining comments from original driver patch series
* Move RD_FIFO_CFG to be ordered corretly
* Expand spinlock comment
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Most modern SPI controllers can directly map a SPI memory (or a portion
of the SPI memory) in the CPU address space. Most of the time this
brings significant performance improvements as it automates the whole
process of sending SPI memory operations every time a new region is
accessed.
This new API allows SPI memory drivers to create direct mappings and
then use them to access the memory instead of using spi_mem_exec_op().
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The logic surrounding the ->exec_op() call applies to direct mapping
accessors. Move this code to separate functions to avoid duplicating
code.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When defining spi_mem_op templates we don't necessarily know the size
that will be passed when the template is actually used, and basing the
supports_op() check on op->data.nbytes to know whether there will be
data transferred for a specific operation is this not possible.
Add SPI_MEM_NO_DATA to the spi_mem_data_dir enum so that we can base
our checks on op->data.dir instead of op->data.nbytes.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I've been wondering still about omap2-mcspi related suspend and resume
flakeyness and looks like we're missing calls to spi_master_suspend()
and spi_master_resume(). Adding those and using pm_runtime_force_suspend()
and pm_runtime_force_resume() makes things work for suspend and resume
and allows us to stop using noirq suspend and resume.
And while at it, let's use SET_SYSTEM_SLEEP_PM_OPS to simplify things
further.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The refactoring done as part of adding the core support for handling
waiting for slave transfer dropped a conditional which meant that we
started waiting for completion of all transfers, not just those that the
controller asked for. This caused hangs and massive delays on platforms
that don't need the core delay. Re-add the delay to fix this.
Fixes: 810923f3bf (spi: Deal with slaves that return from transfer_one() unfinished)
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
drivers/spi/spi-npcm-pspi.c:470:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Fixes: 2a22f1b30c ("spi: npcm: add NPCM PSPI controller driver")
CC: Tomer Maimon <tmaimon77@gmail.com>
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The license text is specifying GPL v2 or later but the MODULE_LICENSE
is set to GPL v2 which means GNU Public License v2 only. So choose the
license text as the correct one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Kauer <florian.kauer@koalo.de>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The u32 variable csgpio is being checked for an error return
from the call to of_get_named_gpio, however, since this is unsigned
this comparison will always be false. Fix this by making csgpio an
int and fix up the %u format specifiers to %d accordingly.
Detected by CoverityScan, CID#1475476 ("Unsigned compared against 0")
Fixes: 2a22f1b30c ("spi: npcm: add NPCM PSPI controller driver")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Do not deselect cs when cs_change is set for the last transfer in the
message. In this case, cs_change indicates that cs should stay selected
until the next transfer.
Signed-off-by: Fredrik Ternerot <fredrikt@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
There doesn't seem to be a way to empty TXFIFO on MMP2. The datasheet is
super-secret and the method described in Armada 16x manual won't work:
"The TXFIFO and RXFIFO are cleared to 0b0 when the SSPx port is reset or
disabled (by writing a 0b0 to the <Synchronous Serial Port Enable> field
in the SSP Control Register 0)."
# devmem 0xd4037008 # read SSSR
0x0000F204
# devmem 0xd4037000 32 0x07 # SSE off in SSCR0
# devmem 0xd4037000 32 0x87 # SSE on
# devmem 0xd4037008
0x0000F204
^ TXFIFO level is still 2. Sigh.
The OLPC 1.75 boot firmware leaves two bytes in the TXFIFO. Those are
basically throwaway bytes used in response to the messages from the EC.
The OLPC kernel copes with this by power-cycling the hardware. Perhaps
the firmware should do this instead.
Other than that, there's not much we can do other than complain loudly
until the garbage gets drained and discard the actual data... For the
OLPC EC this will work just fine and pushing more data to TXFIFO would
break further transactions.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Strobe a GPIO line when the slave TX FIFO is filled. This is how the
Embedded Controller on an OLPC XO-1.75 machine, that happens to be a SPI
master, learns that it can initiate a transaction.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Tested-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Tested on an OLPC XO-1.75 machine, where the Embedded Controller happens
to be a SPI master.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some drivers, such as spi-pxa2xx return from the transfer_one callback
immediately, idicating that the transfer will be finished asynchronously.
Normally, spi_transfer_one_message() synchronously waits for the
transfer to finish with wait_for_completion_timeout(). For slaves, we
don't want the transaction to time out as it can complete in a long time
in future. Use wait_for_completion_interruptible() instead.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some devices such as the TPO TPG110 display panel require
a "high-impedance turn-around", in effect a clock cycle after
switching the line from output to input mode.
Support this in the GPIO driver to begin with. Other driver
may implement it if they can, it is unclear if this can
be achieved with anything else than GPIO bit-banging.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Enable McSPI driver to be built for K3 platforms, to support McSPI on
AM654 SoC of K3 family.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Kernel contains QSPI driver strongly tied to MTD and nor-flash memory.
New spi-mem interface allows usage also other memory types, especially
much larger NAND with SPI interface. This driver works as SPI controller
and is not related to MTD, however can work with NAND-flash or other
peripherals using spi-mem interface.
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Piotr Bugalski <bugalski.piotr@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a driver for Macronix SPI controller IP.
Signed-off-by: Mason Yang <masonccyang@mxic.com.tw>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Re-arrange existing APIs in probe function to
avoid using goto and remove redundant variables.
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
fixed the nitpicks.
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SoC share one irq number between DSPI controllers.
For example, on the LX2160 board, DSPI0 and DSPI1 share one irq number.
In this case, only one DSPI controller can register successfully,
and others will fail.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel LPSS private register restoring in spi-pxa2xx.c: pxa2xx_spi_resume()
was added before there was no any other code restoring them. This was
changed after following commits for previous and current LPSS platforms:
c78b083066 ("ACPI / LPSS: custom power domain for LPSS")
41a3da2b8e ("mfd: intel-lpss: Save register context on suspend")
However there is one caveat: There is no LPSS private register context
save/restore for the Intel Lynxpoint in the Linux kernel code.
I did some debugging on one Lynxpoint based device I have and on it the
LPSS register context is not lost over suspend/resume cycle (s2idle).
Which happens for instance on Intel Braswell. I'm speculating but I guess
either firmware does it or the LPSS is kept always on Lynxpoint.
Given that we haven't needed to implement Lynxpoint LPSS I2C or UART
private register context save/restore over four years time I think we are
safe to remove this LPSS private register restoring during resume here.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add missing support for lsb-first mode.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware supports 4, 8 and 16bit spi words,
so add the missing support for 4bit words.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Register an interrupt handler to fill/empty the
tx and rx fifos rather than busy-looping.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now that we no longer potentially change spi clock
at runtime we can precompute the rx sample delay
at probe time rather than for each transfer.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver previously checked each transfer if the
requested speed was higher than possible with the
current spi clock rate and raised the clock rate
accordingly.
However, there is no check to see if the spi clock
was actually set that high and no way to dynamically
lower the spi clock rate again.
So it seems any potiential users of this functionality
are better off just setting the spi clock rate at init
using the assigned-clock-rates devicetree property.
Removing this dynamic spi clock rate raising allows
us let the spi framework handle min/max speeds
for us.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
We only need to know if we're using dma when setting
up the transfer, so just use a local variable for
that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
In almost all cases we already have a pointer to the
spi master structure where we have the driver data.
The only exceptions are the dma callbacks which are
easily fixed by passing them the master and using
spi_master_get_devdata to retrieve the driver data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi master (aka spi controller) structure already
has two fields for storing the rx and tx dma channels.
Just use them rather than duplicating them in driver data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Just read transfer info directly from the spi device
and transfer structures rather than storing it in
driver data first.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Successful transfers leave the spi disabled, so if
we just make sure to disable the spi on error
there should be no need to disable the spi from
master->unprepare_message.
This also flushes the tx and rx fifos,
so no need to do that manually.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The state field is currently only used to make sure
only the last of the tx and rx dma callbacks issue
an spi_finalize_current_transfer.
Rather than using a spinlock we can get away
with just turning the state field into an atomic_t.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hardware supports 3 different variants of SPI
and there were some code around it, but nothing
to actually set it to anything but "Motorola SPI".
Just drop that code and always use that mode.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use C99 designated initializers for dma slave config
structures. This also makes sure uninitialized fields
are zeroed so we don't need an explicit memset.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_enable_chip function takes a boolean
argument. Change the type to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
when xfer_len is greater than 64 bytes and use fifo mode
to transfer, the actual length from the third time is mata->xfer_len
but not len in mtk_spi_interrupt().
Signed-off-by: Leilk Liu <leilk.liu@mediatek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
ARM-based 63xx DSL platforms have the spi-bcm63xx-hsspi controller
present, allow using this driver there as well.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support to use McSPI controller as SPI slave. In slave mode, DMA TX
completion does not mean entire data has been shifted out as data might
still be stuck in FIFO waiting for master to clock the bus. Therefore,
add an IRQ handler for slave mode to know when entire data in FIFO has
been shifted out.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
McSPI has 32 byte FIFO in Transmit-Receive mode. Current code tries to
configuration FIFO watermark level for DMA trigger to be GCD of transfer
length and max FIFO size which would mean trigger level may be set to 32
for transmit-receive mode if length is aligned. This does not work in
case of SPI slave mode where FIFO always needs to have data ready
whenever master starts the clock. With DMA trigger size of 32 there will
be a small window during slave TX where DMA is still putting data into
FIFO but master would have started clock for next byte, resulting in
shifting out of stale data. Similarly, on Slave RX side there may be RX
FIFO overflow
Fix this by setting FIFO watermark for DMA trigger to word
length. This means DMA is triggered as soon as FIFO has space for word
length bytes and DMA would make sure FIFO is almost always full
therefore improving FIFO occupancy in both master and slave mode.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use standard readl_poll_timeout() macro for polling on status bits.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The qspi controller is a specialized communication interface
targeting single, dual or quad SPI Flash memories (NOR/NAND).
It can operate in any of the following modes:
-indirect mode: all the operations are performed using the quadspi
registers
-read memory-mapped mode: the external Flash memory is mapped to the
microcontroller address space and is seen by the system as if it was
an internal memory
tested on:
-NOR: mx66l51235l
-NAND: MT29F2G01ABAGD
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DMA API does its own zone decisions based on the coherent_dma_mask.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since commit 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
platform_get_irq() can return -EPROBE_DEFER. However, the driver overrides
an error returned by that function with -ENOENT which breaks the deferred
probing. Propagate upstream an error code returned by platform_get_irq()
and remove the bogus "platform" from the error message, while at it...
Fixes: 9ec36cafe4 ("of/irq: do irq resolution in platform_get_irq")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use PIO mode instead if size is smaller than fifo size, since
dma may be less efficient.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Correct wml as the last rx sg length instead of the whole transfer
length. Otherwise, mtd_stresstest will be failed as below:
insmod mtd_stresstest.ko dev=0
=================================================
mtd_stresstest: MTD device: 0
mtd_stresstest: not NAND flash, assume page size is 512 bytes.
mtd_stresstest: MTD device size 4194304, eraseblock size 65536, page size 512, count of eraseblocks 64, pa0
mtd_stresstest: doing operations
mtd_stresstest: 0 operations done
mtd_test: mtd_read from 1ff532, size 880
mtd_test: mtd_read from 20c267, size 64998
spi_master spi0: I/O Error in DMA RX
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
mtd_test: error: read failed at 0x20c267
mtd_stresstest: error -110 occurred
=================================================
insmod: ERROR: could not insert module mtd_stresstest.ko: Connection timed out
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Current dynamic burst length is based on the whole transfer length,
that's ok if there is only one sg, but is not right in case multi sgs
in one transfer,because the tail data should be based on the last sg
length instead of the whole transfer length. Move wml setting for DMA
to the later place, thus, the next patch could get the right last sg
length for wml setting. This patch is a preparation one, no any
function change involved.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI configuration state includes an SPI_NO_CS flag that disables
all CS line manipulation, for applications that want to manage their
own chip selects. However, this flag is ignored by the GPIO CS code
in the SPI framework.
Correct this omission with a trivial patch.
Signed-off-by: Phil Elwell <phil@raspberrypi.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MMP2 platform, that uses device tree, has this controller. Let's add
devicetree alongside platform & PCI.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver supports GENI based SPI Controller in the Qualcomm SOCs. The
Qualcomm Generic Interface (GENI) is a programmable module supporting a
wide range of serial interfaces including SPI. This driver supports SPI
operations using FIFO mode of transfer.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Dilip Kota <dkota@codeaurora.org>
Signed-off-by: Alok Chauhan <alokc@codeaurora.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let the dma/non-dma code paths handle the spi enable
flag themselves. This removes some logic to determine
if the flag should be turned on before or after dma
and also don't leave the spi enabled if the dma path
fails.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dma direction for the tx and rx dma channels never
change, so just use the constants directly rather
than storing them in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The driver data has a u32 field use_dma which is
only ever used as a boolean, so change its type
to reflect that.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
We no longer need the dma_caps since the dma driver
already clamps the burst length to the hardware limit,
so don't request and store dma_caps in device data.
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signal tx dma when spi fifo is less than half full,
and limit tx bursts to half the fifo length.
Clamp rx burst length to 1 to avoid alignment issues.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
The rxconf and txconf structs are allocated on the
stack, so make sure we zero them before filling out
the relevant fields.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
New driver for Qualcomm QuadSPI(QSPI) controller that is used to
communicate with slaves such as flash memory devices. The QSPI controller
can operate in 2 or 4 wire mode but only supports SPI Mode 0. The
controller can also operate in Single or Dual data rate modes.
Signed-off-by: Girish Mahadevan <girishm@codeaurora.org>
Signed-off-by: Ryan Case <ryandcase@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for a new devicetree compatible string called
'amazon,alpine-apb-ssi', which is necessary for the Amazon Alpine spi
controller. 'amazon,alpine-dw-apb-ssi' is used in the dw spi driver if
specified in the devicetree. Otherwise, fall back to driver default
behavior, i.e. original dw IP hw driver behavior.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixing/optimizing bcm_qspi_bspi_read() performance introduced two
changes:
1) It added a loop to read all requested data using multiple BSPI ops.
2) It bumped max size of a single BSPI block request from 256 to 512 B.
The later change resulted in occasional BSPI timeouts causing a
regression.
For some unknown reason hardware doesn't always handle reads as expected
when using 512 B chunks. In such cases it may happen that BSPI returns
amount of requested bytes without the last 1-3 ones. It provides the
remaining bytes later but doesn't raise an interrupt until another LR
start.
Switching back to 256 B reads fixes that problem and regression.
Fixes: 345309fa7c ("spi: bcm-qspi: Fix bcm_qspi_bspi_read() performance")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
During implementation of the new API bcm_qspi_bspi_set_flex_mode() has
been modified breaking calculation of address length. An unnecessary
multiplication was added breaking flash reads.
Fixes: 5f195ee7d8 ("spi: bcm-qspi: Implement the spi_mem interface")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
spidev will make a big fuss if a device tree node binds a device by
using "spidev" as the node's compatible property.
However, the logic for this isn't looking for "spidev" in the
compatible, but rather checking that the device is NOT compatible with
spidev's list of devices.
This causes a false positive if a device not named "rohm,dh2228fv", etc.
binds to spidev, even if a means other than putting "spidev" in the
device tree was used. E.g., the sysfs driver_override attribute.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
This attribute works the same was as the identically named attribute
for PCI, AMBA, and platform devices. For reference, see:
commit 3cf3857134 ("ARM: 8256/1: driver coamba: add device binding
path 'driver_override'")
commit 3d713e0e38 ("driver core: platform: add device binding path
'driver_override'")
commit 782a985d7a ("PCI: Introduce new device binding path using
pci_dev.driver_override")
If the name of a driver is written to this attribute, then the device
will bind to the named driver and only the named driver.
The device will bind to the driver even if the driver does not list the
device in its id table. This behavior is different than the driver's
bind attribute, which only allows binding to devices that are listed as
supported by the driver.
It can be used to bind a generic driver, like spidev, to a device.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Certain devices don't work well when a transmit FIFO underrun or
receive FIFO overrun occurs. Example is the SAF400x radio chip when
running at high speed which leads to garbage being sent to/received from
the chip. In which case, it should stall waiting for further data to be
available before proceeding. This patch unset the NOSTALL bit in CFGR1
by default to prevent this issue.
Signed-off-by: Hieu Tran Dang <dangtranhieu2012@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is implicitly converted to another.
drivers/spi/spi-ep93xx.c:342:62: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
nents = dma_map_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:428:58: note: expanded from macro
'dma_map_sg'
#define dma_map_sg(d, s, n, r) dma_map_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:348:57: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
drivers/spi/spi-ep93xx.c:377:56: warning: implicit conversion from
enumeration type 'enum dma_transfer_direction' to different enumeration
type 'enum dma_data_direction' [-Wenum-conversion]
dma_unmap_sg(chan->device->dev, sgt->sgl, sgt->nents, dir);
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~
./include/linux/dma-mapping.h:429:62: note: expanded from macro
'dma_unmap_sg'
#define dma_unmap_sg(d, s, n, r) dma_unmap_sg_attrs(d, s, n, r, 0)
~~~~~~~~~~~~~~~~~~ ^
3 warnings generated.
dma_{,un}map_sg expect an enum of type dma_data_direction but this
driver uses dma_transfer_direction for everything. Convert the driver to
use dma_data_direction for these two functions.
There are two places that strictly require an enum of type
dma_transfer_direction: the direction member in struct dma_slave_config
and the direction parameter in dmaengine_prep_slave_sg. To avoid using
an explicit cast, add a simple function, ep93xx_dma_data_to_trans_dir,
to safely map between the two types because they are not 1 to 1 in
meaning.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
With this commit the DSPI driver on the BK4 board can be used for SPI
transmission managed from user space (via /dev/spidev0.0).
Example usage/testing:
insmod ./spi-fsl-dspi.ko
./spidev_test -D /dev/spidev0.0 -s 3000000 -v -H -b 8 -p "\xCC\x11\x22\x74"
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Rewrite switch code block to directly do the expected number
of shifts in each case and have break statements.
Addresses-Coverity-ID: 1056539 ("Missing break in switch")
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Apparently, this code does not actually fall through to the next case
because the machine restarts before it has a chance. However, for the
sake of maintenance and readability, we better add the missing break
statement.
Addresses-Coverity-ID: 1437892 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added spi-mem
code. The Tegra fix is relatively large but fairly straightforward and
mechanical, it runs on probe so it's been reasonably well covered in
-next testing.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluuOnETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0AhkB/9ahKdmxdxu0uuzzvS5qmdGD+98dTaV
M+7+Bq6CJfBz0YTc9dxTiynbJot15vo5mKDZkDaJrgOoLCWWDGWa/DjRif2qS2o9
QxjWlBPzfOhKb81/HMJ+MaIHYDtAxvCu4iZExUZPxZzypX8Q9U3+9a/u0+JnRug2
guQ/4vYdxTGbR/taFsKLzf28DRqQb74KuDRAHaN44UYBxA1begy5gFOc7cEQTRu0
WACGM8jNL2eWWLXDNnQQTfb2t1v7LbbMorazyCn2e5ujamE4+DSaYWJF5axZiaQN
ZcRVATw0SPiQlsQW/G014SSFJT0waybxWLOynWS9MSgjx84/GRYWvxRv
=3ATM
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
Quite a few fixes for the Renesas drivers in here, plus a fix for the
Tegra driver and some documentation fixes for the recently added
spi-mem code. The Tegra fix is relatively large but fairly
straightforward and mechanical, it runs on probe so it's been
reasonably well covered in -next testing."
* tag 'spi-fix-v4.19-rc5' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-mem: Move the DMA-able constraint doc to the kerneldoc header
spi: spi-mem: Add missing description for data.nbytes field
spi: rspi: Fix interrupted DMA transfers
spi: rspi: Fix invalid SPI use during system suspend
spi: sh-msiof: Fix handling of write value for SISTR register
spi: sh-msiof: Fix invalid SPI use during system suspend
spi: gpio: Fix copy-and-paste error
spi: tegra20-slink: explicitly enable/disable clock
The of_find_spi_device_by_node() helper function is useful for other
modules too. Export the funciton as GPL like all other spi helper
functions and make it available if CONFIG_OF is enabled, because it isn't
related to the CONFIG_OF_DYNAMIC context. Finally add a stub if
CONFIG_OF isn't enabled, so others must not care about it.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Use the appropriate SPDX license identifier and drop the previous
license text.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
On r8a7791/koelsch:
m25p80 spi0.0: error -22 reading 9f
m25p80: probe of spi0.0 failed with error -22
Apparently the logic in spi_mem_check_op() is wrong, rejecting the
spi-mem operation if any buswidth is valid, instead of invalid.
Fixes: 380583227c ("spi: spi-mem: Add extra sanity checks on the op param")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The __exit section is left out for built-in drivers, so a
'remove' callback must not be marked as such to avoid breaking when
we unbind a device at runtime. This was pointed out by kbuild:
`sprd_spi_remove' referenced in section `.data' of drivers/spi/spi-sprd.o: defined in discarded section `.exit.text' of drivers/spi/spi-sprd.o
Fixes: e7d973a31c ("spi: sprd: Add SPI driver for Spreadtrum SC9860")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clang warns when one enumerated type is converted implicitly to another:
drivers/spi/spi-pic32.c:323:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_FROM_DEVICE,
^~~~~~~~~~~~~~~
drivers/spi/spi-pic32.c:333:8: warning: implicit conversion from
enumeration type 'enum dma_data_direction' to different enumeration type
'enum dma_transfer_direction' [-Wenum-conversion]
DMA_TO_DEVICE,
^~~~~~~~~~~~~
2 warnings generated.
Use the proper enums from dma_transfer_direction (DMA_FROM_DEVICE =
DMA_DEV_TO_MEM = 2, DMA_TO_DEVICE = DMA_MEM_TO_DEV = 1) to satify Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/159
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some combinations are simply not valid and should be rejected before
the op is passed to the SPI controller driver.
Add an spi_mem_check_op() helper and use it in spi_mem_exec_op() and
spi_mem_supports_op() to make sure the spi-mem operation is valid.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This remove the check and subsequent return of error for the case when
a SPI device requires SPI_CS_WORD and is also configured to use a GPIO
for the CS line.
Commit a134cc414e86 ("spi: always use software fallback for SPI_CS_WORD
when using cs_gio") handles this case now, so this check is no longer
necessary.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This modifies the condition for using the software fallback
implementation for SPI_CS_WORD when the SPI controller is using a GPIO
for the CS line. When using a GPIO for CS, the hardware implementation
won't work, so we just enable the software fallback globally in this
case.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mediatek SPI driver modifies some fields (tx_buf, rx_buf, len, tx_dma,
rx_dma) of the spi_transfer* passed in when doing transfer_one and in
interrupt handler. This is somewhat unexpected, and there are some
caller (e.g. Cr50 spi driver) that reuse the spi_transfer for multiple
messages. Add a field to record how many bytes have been transferred,
and calculate the right len / buffer based on it instead.
Signed-off-by: Pi-Hsun Shih <pihsun@chromium.org>
Change-Id: I23e218cd964f16c0b2b26127d4a5ca6529867673
Signed-off-by: Mark Brown <broonie@kernel.org>
If the pll clock needs to be enabled to get its rate, it will also need
to be enabled to provide it. So ensure it is kept enabled through the
lifetime of the device.
Fixes: 0d7412ed1f ("spi/bcm63xx-hspi: Enable the clock before calling clk_get_rate().")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It makes no sense to remove the device on shutdown. And it break things
when the hardware crucial for shutdown (such as the embedded controller)
is attached to the SPI bus.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Signed-off-by: Mark Brown <broonie@kernel.org>
This adds support for the SPI_CS_WORD flag to the TI DaVinci SPI
driver. This mode can be used as long as we are using the hardware
chip select and not a GPIO chip select.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This provides a SPI operation mode which changes chip select after every
word, used by some devices such as ADCs and DACs.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlugGWgTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0OAqB/99Zk/yjUqw3q8mQ9TcDyurMrllpNYm
n9KshwKOc1wyfHsbPMke+ytCJHmMpNDKbv80Dk5aTNBvbeNN9OZdcqonGfVfulEB
hhZy6X4wN6QwX6HpIeWl52o4V4zLd0skeZOqMod/4RQKQvG7kCVVetKFfzMBxYpP
4B+jVLg/L/lVsbNqXe53A59C0myg/lkCBFL9uWmiUaAScS/eeWmHX/Z+Guf3DTjo
eR0ZoB55HeovL8AsTV0xAwjae+YM6LMElptXLF/+AlaFmW4WmuRGuU2tCXh+SaHU
/VzwLgekzd1hplHc8tX1Nhdr4qJhI6tcpQOu+IelTqZ/Z/JlpIruaJVB
=sMBd
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlugGesTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0LpbB/9eeBHjpAthphCZ1Q87oUtqn0dbhV9j
+djnjM3BgJX+3T3vl6fnOtyD2MPg/sGX8pMePEcVqUSRp+StY5tCO++zbR7maMxs
Czw5GslnJJ9CG6T7xx1ZE1vWAIeWywH7Pw98daFJpQkj17BEhGrrqSbpctJaRdSy
3e5nZvc3mWQ5k4ttmK+C9MTa6XV3ReaHDfJaagXWM7bykV6mDwVh6dyx4QJ7kwht
Ti+MQ+SYZndySXTFoborSss+5zgYIJ5nKr07PvOsNrjlk2p3hoU+y7MuU+RB9zzs
XP9dgZKSoLWbFdCspaC6DtcT1P2HLQRi5kBfdc8xlUCupa6Y2Jt3Hms1
=TFpo
-----END PGP SIGNATURE-----
Merge tag 'spi-cs-word' into spi-4.20
spi: Provide SPI_CS_WORD
This provides a SPI operation mode which changes chip select after every
word, used by some devices such as ADCs and DACs.
This adds a default software implementation for the SPI_CS_WORD flag for
controllers that don't have such a feature.
The SPI_CS_WORD flag indicates that the CS line should be toggled
between each word sent, not just between each transfer. The
implementation works by using existing functions to split transfers into
one-word-sized transfers and sets the cs_change bit for each of the
new transfers.
Signed-off-by: David Lechner <david@lechnology.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As well as one driver fix there's a couple of fixes here which address
issues with the use of IDRs for allocation of dynamic bus numbers,
ensuring that dynamic bus numbers interact well with static bus numbers
assigned via DT and otherwise.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAluf2foTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DooB/4/c+c9nX31WeKh5EUFS3WJUQ4quHC+
ZPS0rqliJm0KQxdSCU6ig2+xbobZWAs9T4ZXPlE7PNk6DmqdtATS5jlzbwmoLvdA
PvxsBwz3dRdIGR/BNbDYEZCb0WGtMHO6BR5c//lBCy+ea5oNENi0w0mFnY+AVeUt
ivM55i/nNmV4DReT3rl5mRz/TQgfI9zc11DPpqDnlQML3emYHmJ+hZa8/1g68d8C
lQHLIQMo6hGyOd3p6uPODGt98cDKIuYl9+fcYVzYFScNshwuMsxTDUXpkhv85Frb
QV6LGlikaEQBh9X9BHjzTHMBqbTFVLX/I+jRC/vK2G21862rfOt3R6vh
=rRj7
-----END PGP SIGNATURE-----
Merge tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark writes:
"spi: Fixes for v4.19
As well as one driver fix there's a couple of fixes here which address
issues with the use of IDRs for allocation of dynamic bus numbers,
ensuring that dynamic bus numbers interact well with static bus numbers
assigned via DT and otherwise."
* tag 'spi-fix-v4.19-rc4' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: spi-fsl-dspi: fix broken DSPI_EOQ_MODE
spi: Fix double IDR allocation with DT aliases
spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_sqi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-davinci.c: In function 'davinci_spi_setup':
drivers/spi/spi-davinci.c:422:36: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The DaVinci SPI can use either:
- Internal chip selects (inside the SPI host)
- External chip selects (using GPIO)
- External chip selects passed in pdata
The last way of passing external chip selects through
platform data is not used in the kernel. Delete it to make
the code simpler when refactoring GPIO.
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@kernel.org>
Cc: Michele Dionisio <michele.dionisio@gmail.com>
Cc: Frode Isaksen <fisaksen@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
We need that to adjust the len of the 2nd transfer (called data in
spi-mem) if it's too long to fit in a SPI message or SPI transfer.
Fixes: c36ff266dc ("spi: Extend the core to ease integration of SPI memory controllers")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This is the driver for at91-usart in spi mode. The USART IP can be configured
to work in many modes and one of them is SPI.
The driver was tested on sama5d3-xplained and sama5d4-xplained boards with
enc28j60 ethernet controller as slave.
Signed-off-by: Radu Pirea <radu.pirea@microchip.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviwed-by: Mark Brown <broonie@kernel.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
There is a logical problem in spi-gpio with host just
assigning a MOSI line and no MISO: this is interpreted
as the host cannot do RX and the host is flagged with
SPI_MASTER_NO_RX.
This is wrong: since GPIO lines can switch direction,
in 3WIRE operation the host will simply reverse the
direction of the GPIO line and start reading from it,
there is even code for doing this in the driver, but
it went unnoticed because it was tested by using a
master with 4 wires but a device using just 3 wires.
Remove the offending flag.
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Almost all spi drivers assign spi master->dev.of_node from
its parent platform device without additional refcounting.
It seems of_node_get() in pic32_spi_probe() is unnecessary
and there is no corresponding of_node_put().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-pl022.c: In function 'do_polling_transfer':
drivers/spi/spi-pl022.c:1493:20: warning:
variable 'chip' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi-dw driver currently only supports 8 or 16 bits per word.
Since the hardware supports 4-16 bits per word, adapt the driver
to also support this.
Tested on socfpga cyclone5 with a 9-bit SPI display.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-gpio.c: In function 'spi_gpio_remove':
drivers/spi/spi-gpio.c:450:33: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When interrupted, wait_event_interruptible_timeout() returns
-ERESTARTSYS, and the SPI transfer in progress will fail, as expected:
m25p80 spi0.0: SPI transfer failed: -512
spi_master spi0: failed to transfer one message from queue
However, as the underlying DMA transfers may not have completed, all
subsequent SPI transfers may start to fail:
spi_master spi0: receive timeout
qspi_transfer_out_in() returned -110
m25p80 spi0.0: SPI transfer failed: -110
spi_master spi0: failed to transfer one message from queue
Fix this by calling dmaengine_terminate_all() not only for timeouts, but
also for errors.
This can be reproduced on r8a7991/koelsch, using "hd /dev/mtd0" followed
by CTRL-C.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume,
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Based on a patch for sh-msiof by Gaku Inami.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
This patch changes writing to the SISTR register according to the H/W
user's manual.
The TDREQ bit and RDREQ bits of SISTR are read-only, and must be written
their initial values of zero.
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI queue is running during system suspend, the system may lock
up.
Fix this by stopping/restarting the queue during system suspend/resume
by calling spi_master_suspend()/spi_master_resume() from the PM
callbacks. In-kernel users will receive an -ESHUTDOWN error while
system suspend/resume is in progress.
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
[geert: Cleanup, reword]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
spi_controller_{suspend,resume}() already prints an error message on
failure, so there is no need to repeat this in individual drivers.
Note: spi_master_{suspend,resume}() is an alias for
spi_controller_{suspend,resume}().
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Daniel Mack <daniel@zonque.org>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This fixes an embarrassing copy-and-paste error in the
errorpath of spi_gpio_request(): we were checking the wrong
struct member for error code right after retrieveing the
sck GPIO.
Fixes: 9b00bc7b90 ("spi: spi-gpio: Rewrite to use GPIO descriptors")
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This change increases the source code readability.
Instead of using `spi->child[cs].direct_access.XXX` use `dir_acc->XXX`.
Instead of using `orion_spi->child[cs].direct_access.vaddr` use `vaddr`.
Signed-off-by: Kosta Zertsekel <zertsekel@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
Depending on the SPI instance one may get an interrupt storm upon
requesting resp. interrupt unless the clock is explicitly enabled
beforehand. This has been observed trying to bring up instance 4 on
T20.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Define a mask for the IF_SI_OWNER field.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/spi/spi-davinci.c: In function 'davinci_spi_chipselect':
drivers/spi/spi-davinci.c:211:36: warning:
variable 'pdata' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Unfortunately, the Jaguar2 CPU_SYSTEM_CTRL register set has a different
layout than the Ocelot one. Handle that while keeping most of the code
common.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch adds the SPI controller driver for Spreadtrum SC9860 platform.
Signed-off-by: Lanqing Liu <lanqing.liu@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fixes the dspi_eoq_write function used by the
ColdFire mcf5441x family. The 16 bit cmd part must be re-set at
each data transfer.
Also, now that fifo_size variables are used for eoq_read/write,
a proper fifo size must be set (16 slots for the ColdFire dspi
module version).
Signed-off-by: Angelo Dureghello <angelo@sysam.it>
Acked-by: Esben Haabendal <esben@haabendal.dk>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
If the SPI bus number is provided by a DT alias, idr_alloc() is called
twice, leading to:
WARNING: CPU: 1 PID: 1 at drivers/spi/spi.c:2179 spi_register_controller+0x11c/0x5d8
couldn't get idr
Fix this by moving the handling of fixed SPI bus numbers up, before the
DT handling code fills in ctlr->bus_num.
Fixes: 1a4327fbf4 ("spi: fix IDR collision on systems with both fixed and dynamic SPI bus numbers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
This introduces devres helpers and an API to request a lock by name,
then migrates the sprd SPI driver to use these.
-----BEGIN PGP SIGNATURE-----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=zanh
-----END PGP SIGNATURE-----
Merge tag 'hwlock-v4.19' of git://github.com/andersson/remoteproc
Pull hwspinlock updates from Bjorn Andersson:
"This introduces devres helpers and an API to request a lock by name,
then migrates the sprd SPI driver to use these"
* tag 'hwlock-v4.19' of git://github.com/andersson/remoteproc:
hwspinlock: Fix incorrect return pointers
spi: sprd: Change to use devm_hwspin_lock_request_specific()
spi: sprd: Replace of_hwspin_lock_get_id() with of_hwspin_lock_get_id_byname()
hwspinlock: Fix one comment mistake
hwspinlock: Remove redundant config
hwspinlock: Add devm_xxx() APIs to register/unregister one hwlock controller
hwspinlock: Add devm_xxx() APIs to request/free hwlock
hwspinlock: Add one new API to support getting a specific hwlock by the name
On systems where some controllers get a dynamic ID assigned and some have
a fixed number (e.g. from ACPI tables), the current implementation might
run into an IDR collision: in case of a fixed bus number is gotten by a
driver (but not marked busy in IDR tree) and a driver with dynamic bus
number gets the same ID and predictably fails.
Fix this by means of checking-in fixed IDsin IDR as far as dynamic ones
at the moment of the controller registration.
Fixes: 9b61e30221 (spi: Pick spi bus number from Linux idr or spi alias)
Signed-off-by: Kirill Kapranov <kirill.kapranov@compulab.co.il>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
On non-OF systems spi->controlled_data may be NULL. This causes a NULL
pointer derefence on dm365-evm.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
When porting (Q)SPI controller drivers from the MTD layer to the SPI
layer, the naming scheme for the memory devices changes. To be able
to keep compatibility with the old drivers naming scheme, a name
field is added to struct spi_mem and a hook is added to let controller
drivers set a custom name for the memory device.
Example for the FSL QSPI driver:
Name with the old driver: 21e0000.qspi,
or with multiple devices: 21e0000.qspi-0, 21e0000.qspi-1, ...
Name with the new driver without spi_mem_get_name: spi4.0
Suggested-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This commit removed include headers of linux/of.h and linux/of_platform.h,
because they are not used.
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SPI_3WIRE support to spi-gpio controller introducing
set_line_direction function pointer in spi_bitbang data structure.
Spi-gpio controller has been tested using hts221 temp/rh iio sensor
running in 3wire mode and lsm6dsm running in 4wire mode
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the capability to specify the flag parameter used in
bitbang_txrx_be_cpha{0,1} through the txrx_word function pointers of
spi_bitbang data structure. That feature will be used to add spi-3wire
support to the spi-gpio controller
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add SPI controller driver implemented in Socionext UniPhier SoCs.
UniPhier SoCs have two types SPI controllers; SCSSI supports a
single channel, and MCSSI supports multiple channels.
This driver supports SCSSI only.
This controller has 32bit TX/RX FIFO with depth of eight entry,
and supports the SPI master mode only.
This commit is implemented in PIO transfer mode, not DMA transfer.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Keiji Hayashibara <hayashibara.keiji@socionext.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Even if the chip select line is not controlled by the SPFI
hardware, the device select bits need to be set to specify
the chip select line in use for the hardware to know what
parameters to use for the current transfer.
Signed-off-by: Ionela Voinescu <ionela.voinescu@imgtec.com>
Signed-off-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Variable count, l, mcspi and spi_cntrl are being assigned but are
never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'count' set but not used [-Wunused-but-set-variable]
warning: variable 'l' set but not used [-Wunused-but-set-variable]
warning: variable 'mcspi' set but not used [-Wunused-but-set-variable]
warning: variable 'spi_cntrl' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Because the SPI controller deasserts the chip select when the TX fifo is
empty (which may happen in the middle of a transfer), the CS should be
handled by linux. Unfortunately, some or all of the first four chip
selects are not muxable as GPIOs, depending on the SoC.
There is a way to bitbang those pins by using the SPI boot controller so
use it to set the chip selects.
At init time, it is also necessary to give control of the SPI interface to
the Designware IP.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Export dw_spi_set_cs so it can be used from the various IP integration
modules.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Log RX and TX fifo counters when a transfer is done and these are not
zero.
Signed-off-by: Tiago Brusamarello <tiago.brusamarello@datacom.ind.br>
Signed-off-by: Mark Brown <broonie@kernel.org>
Dynamic burst mode allows to group together multiple words and send them
in one continuous burst. When the number of bytes to be sent is not a
strict multiple of the FIFO entry size (32 bits), the controller expects
the non aligned bits to be sent first.
This commit adds support for this particular constraint, avoiding the
need to send the non-aligned bytes one by one at the end of the
transfer, speeding-up transfer speed in that case.
With this method, a transfer is divided into multiple bursts, limited in
size by the maximum amount of data that the controller can transfer in
one continuous burst (which is 512 bytes).
The non-512 byte part of the transfer is sent first. The remaining bytes
to be transferred in the current burst is stored in the 'remainder'
field.
With this method, the read_u32 field is no longer necessary, and is
removed.
This was tested on imx6 solo and imx6 quad.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_imx_can_dma function computes the watermark level so that
the transfer will fit in exactly N bursts (without a remainder).
The smallest watermark level possible being one FIFO entry per burst, we
can't never have a case where the transfer size isn't divsiible by 1.
Remove the extra check for the wml being different than 0.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SPI core enforces that we always use the next power-of-two number of
bytes to store words. As a result, a 24 bits word will be stored in 4
bytes.
This commit fixes the spi_imx_bytes_per_word function to return the
correct number of bytes.
This also allows to get rid of unnecessary checks in the can_dma
function, since the SPI core validates that we always have a transfer
length that is a multiple of the number of bytes per word.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The dynamic bursts mode allows to group together multiple words into a
single burst. To do so, it's necessary that words can be packed into the
32-bits FIFO entries, so we can't allow using this mode with bit_per_words
different to 8, 16 or 32.
This prevents shitfing out extra clock ticks for transfers with
bit_per_word values not aligned on 8 bits.
With that , we are sure that only the correct number of bits is
shifted out at each transfer, so we don't need to mask out the remaining
parts of the words.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some fields in struct spi_imx_data are assigned a different value twice
in a row, in spi_imx_setupxfer.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPMSETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BizB/9lSfg4JrgJdAP8mDWfi7L5LjbpP9bB
9n1MlUFGRGU0Uc/yOD99QA6kB1WSpthFcgLBj+JDn3X30MzOqfZcHb3d9x5Z+XiV
YnIPzYqBPnnMSeTAX21c3Tz5nwO9hgz/xYr8onwYPeJWmt4RltYhiMdCgCQFWm9c
QaYNHiHymJP0ZFPXzLXlnIf+OW21ZOO9bH+eX1PAzbuWoDPxJZ63Eir22eKwTNey
bIIu19sxZE6o6Rd2Z0XAPtSGbd/r/9ULZAQcP429H+ETIfyefC6/IZv+yd4NrHmc
7WpWYi0JNdPLCXgLOvg5mwPBgDfs3tzoInWQu305882qlaK6kkivCgBu
=JPLR
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAltPMZgTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0JxACACAVtjwSy7KjJZ92ZljiyDP2MUydcM8
+6WiN96NCQVgMwFb6WBfePSJFeDeAnr0t4oANZpfa9rGV7YEYB5KlPmkGvuP+u6N
Jj+kRYXNcsu4LiyfZ82b/in3nBQ370Ufe32c4OECD/WDBLUx9TfWcur0sHLjHyp0
wh/9VxqQcGjgt/espt3QGDrASdymWHwF3sTEAoAIOeUzOgO61J2/4fQotUhPVPTN
q7jS6tmbR9GapEKGPOEzRz+3Ici3zK75zM3Yk2wSfh2xXk9Ly9q2HVO7ju7tC8Pe
XMnPxermqar/+PRgYYgLxrUDNyKHlzce4+hqc1cwj0XwAlvMiImB2nsB
=3WLv
-----END PGP SIGNATURE-----
Merge tag 'spi-dw-set-cs' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi into spi-4.19
spi: dw: Allow custom set_cs_callback
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
Allow platform specific drivers to provide their own set_cs callback when
the IP integration requires it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
It is possible to get an interrupt as soon as it is requested. dw_spi_irq
does spi_controller_get_devdata(master) and expects it to be different than
NULL. However, spi_controller_set_devdata() is called after request_irq(),
resulting in the following crash:
CPU 0 Unable to handle kernel paging request at virtual address 00000030, epc == 8058e09c, ra == 8018ff90
[...]
Call Trace:
[<8058e09c>] dw_spi_irq+0x8/0x64
[<8018ff90>] __handle_irq_event_percpu+0x70/0x1d4
[<80190128>] handle_irq_event_percpu+0x34/0x8c
[<801901c4>] handle_irq_event+0x44/0x80
[<801951a8>] handle_level_irq+0xdc/0x194
[<8018f580>] generic_handle_irq+0x38/0x50
[<804c6924>] ocelot_irq_handler+0x104/0x1c0
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Upper layer users of SPI device drivers may rely on 'actual_length',
so it is important that information is correctly reported. One such
example is spi_mem_exec_op() function that will fail if
'actual_length' of the data transferred is not what was requested. Add
necessary code to populate 'actual_length.
Cc: Mark Brown <broonie@kernel.org>
Cc: Sanchayan Maity <maitysanchayan@gmail.com>
Cc: Stefan Agner <stefan@agner.ch>
Cc: cphealy@gmail.com
Cc: linux-spi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix the missing clk_disable_unprepare() before return
from cnds_runtime_resume() in the error handling case.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Registers of DSPI should not be accessed before enabling its clock. On
Toradex Colibri VF50 on Iris carrier board this could be seen during
bootup as imprecise abort:
Unhandled fault: imprecise external abort (0x1c06) at 0x00000000
Internal error: : 1c06 [#1] ARM
Modules linked in:
CPU: 0 PID: 1 Comm: swapper Not tainted 4.14.39-dirty #97
Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
Backtrace:
[<804166a8>] (regmap_write) from [<80466b5c>] (dspi_probe+0x1f0/0x8dc)
[<8046696c>] (dspi_probe) from [<8040107c>] (platform_drv_probe+0x54/0xb8)
[<80401028>] (platform_drv_probe) from [<803ff53c>] (driver_probe_device+0x280/0x2f8)
[<803ff2bc>] (driver_probe_device) from [<803ff674>] (__driver_attach+0xc0/0xc4)
[<803ff5b4>] (__driver_attach) from [<803fd818>] (bus_for_each_dev+0x70/0xa4)
[<803fd7a8>] (bus_for_each_dev) from [<803fee74>] (driver_attach+0x24/0x28)
[<803fee50>] (driver_attach) from [<803fe980>] (bus_add_driver+0x1a0/0x218)
[<803fe7e0>] (bus_add_driver) from [<803fffe8>] (driver_register+0x80/0x100)
[<803fff68>] (driver_register) from [<80400fdc>] (__platform_driver_register+0x48/0x50)
[<80400f94>] (__platform_driver_register) from [<8091cf7c>] (fsl_dspi_driver_init+0x1c/0x20)
[<8091cf60>] (fsl_dspi_driver_init) from [<8010195c>] (do_one_initcall+0x4c/0x174)
[<80101910>] (do_one_initcall) from [<80900e8c>] (kernel_init_freeable+0x144/0x1d8)
[<80900d48>] (kernel_init_freeable) from [<805ff6a8>] (kernel_init+0x10/0x114)
[<805ff698>] (kernel_init) from [<80107be8>] (ret_from_fork+0x14/0x2c)
Cc: <stable@vger.kernel.org>
Fixes: 5ee67b587a ("spi: dspi: clear SPI_SR before enable interrupt")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Intel Ice Lake SPI host controller follows the Intel Cannon Lake but the
PCI IDs are different. Add the new PCI IDs to the driver supported
devices list.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
Change to use devm_hwspin_lock_request_specific() instead of
freeing the hwlock explicitly when unbound the device.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Now the hwlock core has supplied new function to get a specific hwlock id
by one hwlock name, which is more clear for users. So change to use
of_hwspin_lock_get_id_byname().
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
It seems that the proper structure field to use in this particular
case is *regmap_pushr* instead of regmap.
Addresses-Coverity-ID: 1470126 ("Copy-paste error")
Fixes: 58ba07ec79 ("spi: spi-fsl-dspi: Add support for XSPI mode registers")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Esben Haabendal <eha@deif.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Set the XSPI bit for devices configured for XSPI mode (currently LS1021A),
and thereby switch to extended SPI mode, allowing for SPI transfers using
from 4 to 32 bits per word instead of 4 to 16 bits per word.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This implements handling of split CMD and TX FIFO queues for XSPI when
running in TCFQ mode.
It should be simple to add it to EOQ mode also. Currently, EOQ mode is
only used with coldfire. So if coldfire DSPI supports XSPI, XSPI FIFO
handling should be added to EOQ mode also.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This prepares for adding support for extended SPI mode (XSPI), by extending
the regmap with the extra SREX and CTAREx registers.
An additional register map is made for allowing 16 bit access to CMD and TX
FIFO of the PUSHR register separately, which is also needed for XSPI mode
support.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Mark volatile registers to avoid caching bugs.
Note: SPI_MCR is marked volatile because of CLR_TXF and CLR_RXF bits.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The MCR register is not changed, so initialize it in dspi_init().
The exception is the CLR_TXF and CLR_RXF bits, which should be written to
before each transfer to make sure we start with empty FIFOs. With MCR
register now configured as volatile, the regmap_update_bits will do a real
read-modify-write cycle.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This extends the driver with support for all SPI framesizes from 4 to 16
bits, and adds support for per transfer specific bits_per_word, while at
the same time reducing code size and complexity.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify driver by avoiding counter wrapping by clearing transfer counter
on first SPI transfer per interrupt instead of tracking what it was before.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As of 92dc20d83a, transfer->cs_change has
been supported for non-last transfers, but not for last transfer.
This change brings handling of cs_change in line with the specification in
spi.h, implementing handling of transfer->cs_change for all transfers.
The value for CMD FIFO is precalculated with transfer->cs_change field
taken into account, allowing for CS de-activate between transfers and
keeping CS activated after last transfer.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Checking directly against pointer value should be at least as fast as doing
bitmasking and compare, so let's keep it simple.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The if statement just above this if/else statement triggers on the same
condition, and then invalidates it.
Signed-off-by: Esben Haabendal <eha@deif.com>
Acked-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The code did not de-assert any CS GPIOs before probing slaves. This
means that several CS signals could be active at once, garbling the
communication. Whether this was actually a problem depended on the type
of the SPI device attached (so my "spidev" for userspace access worked
correctly because its probe was effectively a no-op), and on the state
of the GPIO pins at SoC's boot.
The code was already iterating through all DT children of the SPI
controller, so this change re-uses that loop for CS GPIO setup as well.
This means that this might change the number of the HW CS signal which
is picked for all GPIO CS devices. Previously, the lowest one was used,
but we now use the first one from the DT.
With this move of the code, we can also finally initialize each GPIO CS
lane before registering the SPI controller (which in turn probes for
slaves).
I tried to fix this in 544248623b already, but that only did it half
way by registering the GPIOs properly. That patch failed to set their
logic signals early enough, though.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Mark Brown <broonie@kernel.org>
The path "spi: cadence: Add usleep_range() for
cdns_spi_fill_tx_fifo()" added a usleep_range() function call,
which cannot be used in atomic context.
However the cdns_spi_fill_tx_fifo() function can be called during
an interrupt which may result in a kernel panic:
BUG: scheduling while atomic: grep/561/0x00010002
Modules linked in:
Preemption disabled at:
[<ffffff800858ea28>] wait_for_common+0x48/0x178
CPU: 0 PID: 561 Comm: grep Not tainted 4.17.0 #1
Hardware name: Cadence CSP (DT)
Call trace:
dump_backtrace+0x0/0x198
show_stack+0x14/0x20
dump_stack+0x8c/0xac
__schedule_bug+0x6c/0xb8
__schedule+0x570/0x5d8
schedule+0x34/0x98
schedule_hrtimeout_range_clock+0x98/0x110
schedule_hrtimeout_range+0x10/0x18
usleep_range+0x64/0x98
cdns_spi_fill_tx_fifo+0x70/0xb0
cdns_spi_irq+0xd0/0xe0
__handle_irq_event_percpu+0x9c/0x128
handle_irq_event_percpu+0x34/0x88
handle_irq_event+0x48/0x78
handle_fasteoi_irq+0xbc/0x1b0
generic_handle_irq+0x24/0x38
__handle_domain_irq+0x84/0xf8
gic_handle_irq+0xc4/0x180
This patch replaces the function call with udelay() which can be
used in an atomic context, like an interrupt.
Signed-off-by: Jan Kotas <jank@cadence.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
In case of a bi-directional transfer, receive DMA may complete in the
rcar-dmac driver before transmit DMA, due to scheduling latencies.
As the MSIOF driver waits for completion of the receive DMA only, it may
submit the next transmit DMA request before the previous one has
completed.
Make the driver more robust by waiting for the completion of both
receive and transmit DMA, when applicable.
Based on a patch in the BSP by Ryo Kataoka.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Mark Brown <broonie@kernel.org>
These include a significant update of the generic power domains (genpd)
and Operating Performance Points (OPP) frameworks, mostly related to
the introduction of power domain performance levels, cpufreq updates
(new driver for Qualcomm Kryo processors, updates of the existing
drivers, some core fixes, schedutil governor improvements), PCI power
management fixes, ACPI workaround for EC-based wakeup events handling
on resume from suspend-to-idle, and major updates of the turbostat
and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks
in the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the
schedutil cpufreq governor (Joel Fernandes, Dietmar Eggemann,
Rafael Wysocki, Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman,
Viresh Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag
set and update stale comments in the PCI core PM code (Rafael
Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver
(David Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=wqBV
-----END PGP SIGNATURE-----
Merge tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These include a significant update of the generic power domains
(genpd) and Operating Performance Points (OPP) frameworks, mostly
related to the introduction of power domain performance levels,
cpufreq updates (new driver for Qualcomm Kryo processors, updates of
the existing drivers, some core fixes, schedutil governor
improvements), PCI power management fixes, ACPI workaround for
EC-based wakeup events handling on resume from suspend-to-idle, and
major updates of the turbostat and pm-graph utilities.
Specifics:
- Introduce power domain performance levels into the the generic
power domains (genpd) and Operating Performance Points (OPP)
frameworks (Viresh Kumar, Rajendra Nayak, Dan Carpenter).
- Fix two issues in the runtime PM framework related to the
initialization and removal of devices using device links (Ulf
Hansson).
- Clean up the initialization of drivers for devices in PM domains
(Ulf Hansson, Geert Uytterhoeven).
- Fix a cpufreq core issue related to the policy sysfs interface
causing CPU online to fail for CPUs sharing one cpufreq policy in
some situations (Tao Wang).
- Make it possible to use platform-specific suspend/resume hooks in
the cpufreq-dt driver and make the Armada 37xx DVFS use that
feature (Viresh Kumar, Miquel Raynal).
- Optimize policy transition notifications in cpufreq (Viresh Kumar).
- Improve the iowait boost mechanism in the schedutil cpufreq
governor (Patrick Bellasi).
- Improve the handling of deferred frequency updates in the schedutil
cpufreq governor (Joel Fernandes, Dietmar Eggemann, Rafael Wysocki,
Viresh Kumar).
- Add a new cpufreq driver for Qualcomm Kryo (Ilia Lin).
- Fix and clean up some cpufreq drivers (Colin Ian King, Dmitry
Osipenko, Doug Smythies, Luc Van Oostenryck, Simon Horman, Viresh
Kumar).
- Fix the handling of PCI devices with the DPM_SMART_SUSPEND flag set
and update stale comments in the PCI core PM code (Rafael Wysocki).
- Work around an issue related to the handling of EC-based wakeup
events in the ACPI PM core during resume from suspend-to-idle if
the EC has been put into the low-power mode (Rafael Wysocki).
- Improve the handling of wakeup source objects in the PM core (Doug
Berger, Mahendran Ganesh, Rafael Wysocki).
- Update the driver core to prevent deferred probe from breaking
suspend/resume ordering (Feng Kan).
- Clean up the PM core somewhat (Bjorn Helgaas, Ulf Hansson, Rafael
Wysocki).
- Make the core suspend/resume code and cpufreq support the RT patch
(Sebastian Andrzej Siewior, Thomas Gleixner).
- Consolidate the PM QoS handling in cpuidle governors (Rafael
Wysocki).
- Fix a possible crash in the hibernation core (Tetsuo Handa).
- Update the rockchip-io Adaptive Voltage Scaling (AVS) driver (David
Wu).
- Update the turbostat utility (fixes, cleanups, new CPU IDs, new
command line options, built-in "Low Power Idle" counters support,
new POLL and POLL% columns) and add an entry for it to MAINTAINERS
(Len Brown, Artem Bityutskiy, Chen Yu, Laura Abbott, Matt Turner,
Prarit Bhargava, Srinivas Pandruvada).
- Update the pm-graph to version 5.1 (Todd Brandt).
- Update the intel_pstate_tracer utility (Doug Smythies)"
* tag 'pm-4.18-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (128 commits)
tools/power turbostat: update version number
tools/power turbostat: Add Node in output
tools/power turbostat: add node information into turbostat calculations
tools/power turbostat: remove num_ from cpu_topology struct
tools/power turbostat: rename num_cores_per_pkg to num_cores_per_node
tools/power turbostat: track thread ID in cpu_topology
tools/power turbostat: Calculate additional node information for a package
tools/power turbostat: Fix node and siblings lookup data
tools/power turbostat: set max_num_cpus equal to the cpumask length
tools/power turbostat: if --num_iterations, print for specific number of iterations
tools/power turbostat: Add Cannon Lake support
tools/power turbostat: delete duplicate #defines
x86: msr-index.h: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: Correct SNB_C1/C3_AUTO_UNDEMOTE defines
tools/power turbostat: add POLL and POLL% column
tools/power turbostat: Fix --hide Pk%pc10
tools/power turbostat: Build-in "Low Power Idle" counters support
tools/power turbostat: Don't make man pages executable
tools/power turbostat: remove blank lines
tools/power turbostat: a small C-states dump readability immprovement
...
* pm-domains:
PM / domains: Improve wording of dev_pm_domain_attach() comment
PM / Domains: Don't return -EEXIST at attach when PM domain exists
spi: Respect all error codes from dev_pm_domain_attach()
soundwire: Respect all error codes from dev_pm_domain_attach()
mmc: sdio: Respect all error codes from dev_pm_domain_attach()
i2c: Respect all error codes from dev_pm_domain_attach()
driver core: Respect all error codes from dev_pm_domain_attach()
amba: Respect all error codes from dev_pm_domain_attach()
PM / Domains: Allow a better error handling of dev_pm_domain_attach()
PM / Domains: Check for existing PM domain in dev_pm_domain_attach()
PM / Domains: Drop redundant code in genpd while attaching devices
PM / Domains: Drop comment in genpd about legacy Samsung DT binding
PM / Domains: Fix error path during attach in genpd
The correct form is "a high-level", so fix it accordingly.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
According to section 59.2.4 MSIOF Receive Mode Register 1 (SIRMDR1) in
the R-Car Gen3 datasheet Rev.1.00, the value of the SIRMDR1.SYNCAC bit
must match the value of the SITMDR1.SYNCAC bit. However,
sh_msiof_spi_setup() changes only the latter.
Fix this by updating the SIRMDR1 register like the SITMDR1 register,
taking into account register bits that exist in SITMDR1 only.
Reported-by: Renesas BSP team via Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Fixes: 7ff0b53c40 ("spi: sh-msiof: Avoid writing to registers from spi_master.setup()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 5a686b2c9e ("spi: omap2-mcspi: Idle hardware during suspend
and resume") added calls for pm_runtime_force_suspend() and
pm_runtime_force_resume() to make sure spi is idled between
device_prepare() and device_complete().
But testing Linux next, I now noticed that we will get the following:
spi_master spi0: Failed to power device: -13
Looking at things more turns out we can just remove this non-standard
code. I was probably testing with some extra experimental patches
earlier when I thought we need pm_runtime_force_suspend() and
pm_runtime_force_resume().
Fixes: 5a686b2c9e ("spi: omap2-mcspi: Idle hardware during suspend
and resume")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If pm_runtime_get_sync() fails we should call pm_runtime_put_noidle().
This is probably not a critical fix as we should only hit this when
things are broken elsewhere.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
resource_size() is dereferencing the res without checking that it is
not NULL, so we need to do the check before calling resource_size().
Fixes: b95cb394ab ("spi: ti-qspi: Implement the spi_mem interface")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since Linux v4.10 release (commit 1d9174fbc5 "PM / Runtime: Defer
resuming of the device in pm_runtime_force_resume()"),
pm_runtime_force_resume() function doesn't runtime resume device if it was
not runtime active before system suspend. Thus, driver should not do any
register access after pm_runtime_force_resume() without checking the
runtime status of the device. To fix this issue, simply move
s3c64xx_spi_hwinit() call to s3c64xx_spi_runtime_resume() to ensure that
hardware is always properly initialized. This fixes Synchronous external
abort issue on system suspend/resume cycle on newer Exynos SoCs.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Cc: stable@vger.kernel.org
The limitation of being able to check only for -EPROBE_DEFER from
dev_pm_domain_attach() has been removed. Hence let's respect all error
codes and bail out accordingly.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Patch http://patchwork.ozlabs.org/patch/905205/ has been partially
applied, and changes to the bcm-qspi driver have been lost somehow
(probably due to a conflict when applying the patch).
Remove the ->spi_flash_read() bits from this driver to fix the build
error.
Fixes: c1f5ba70de ("spi: Get rid of the spi_flash_read() API")
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This API has been replaced by the spi_mem_xx() one, its only user
(spi-nor) has been converted to spi_mem_xx() and all SPI controller
drivers that were implementing the ->spi_flash_xxx() hooks are also
implementing the spi_mem ones. So we can safely get rid of this API.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_mem interface is meant to replace the spi_flash_read() one.
Implement the ->exec_op() method so that we can smoothly get rid of the
old interface.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Vignesh R <vigneshr@ti.com>
Tested-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The spi_mem interface is meant to replace the ->spi_flash_read() one.
Implement the ->exec_op() method to ease removal of the old interface.
Not that ->spi_flash_read() is now implemented as a wrapper around the
new bcm_qspi_exec_mem_op() function so that we can easily get rid of
it when ->spi_flash_read() is removed.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Kamal Dasu <kdasu.kdev@gmail.com>
Tested-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Some SPI/QuadSPI controllers only expose a high-level SPI memory
interface, thus preventing any regular SPI transfers from being done.
In that case, SPI controller drivers can leave all ->transfer_xxx()
hooks empty and only implement the spi_mem_ops interface.
Adjust the core to allow such situations:
- extend spi_controller_check_ops() to accept situations where all
->transfer_xxx() pointers are NULL only if ->mem_ops != NULL
- make sure we do not initialize the SPI message queue if
ctlr->transfer_one and ctlr->transfer_one_message are missing
- return -ENOTSUPP if someone tries to do a regular SPI transfer on
a controller that does not support it
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Tested-by: Frieder Schrempf <frieder.schrempf@exceet.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
