At least for 4430, trying to use the single conversion mode eventually
hangs the thermal sensor. This can be quite easily seen with errors:
thermal thermal_zone0: failed to read out thermal zone (-5)
Also, trying to read the temperature shows a stuck value with:
$ while true; do cat /sys/class/thermal/thermal_zone0/temp; done
Where the temperature is not rising at all with the busy loop.
Additionally, the EOCZ (end of conversion) bit is not rising on 4430 in
single conversion mode while it works fine in continuous conversion mode.
It is also possible that the hung temperature sensor can affect the
thermal shutdown alert too.
Let's fix the issue by adding TI_BANDGAP_FEATURE_CONT_MODE_ONLY flag and
use it for 4430.
Note that we also need to add udelay to for the EOCZ (end of conversion)
bit polling as otherwise we have it time out too early on 4430. We'll be
changing the loop to use iopoll in the following clean-up patch.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-3-tony@atomide.com
On dra7, there is no Start of Conversion (SOC) register bit and we have an
empty bgap_soc_mask in the configuration for the thermal driver. Let's not
do pointless reads and writes with the empty mask.
There's also no point waiting for End of Conversion bit (EOCZ) to go high
on dra7. We only care about it going down, and are now mostly timing out
waiting for EOCZ high while it has already gone down.
When we add checking for the timeout errors in a later patch, waiting for
EOCZ high would cause bogus time out errors.
Cc: Adam Ford <aford173@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: H. Nikolaus Schaller <hns@goldelico.com>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Adam Ford <aford173@gmail.com> #logicpd-torpedo-37xx-devkit
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210205134534.49200-2-tony@atomide.com
This functionality has nothing to do with MCE, move it to the thermal
framework and untangle it from MCE.
Requested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Tested-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Link: https://lkml.kernel.org/r/20210202121003.GD18075@zn.tnic
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210120162400.4115366-3-arnd@kernel.org
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210120162400.4115366-2-arnd@kernel.org
The thermal zone can have cooling devices which are missing power actor
API. This could be due to missing Energy Model for devfreq or cpufreq
cooling device. In this case it is safe to fail the binding rather than
trying to workaround and control the temperature in such thermal zone.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210119114126.19480-1-lukasz.luba@arm.com
The change of the cooling device state should be used by the governor
or at least by the core code, not by the drivers themselves.
Remove the API usage and move the function declaration to the internal
headers.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20210118173824.9970-1-daniel.lezcano@linaro.org
Like previous patch, the intel_pch_thermal device is not in ACPI
ThermalZone namespace, so a critical trip doesn't mean shutdown.
Override the default .critical callback to prevent surprising thermal
shutdoown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-2-kai.heng.feng@canonical.com
We are seeing thermal shutdown on Intel based mobile workstations, the
shutdown happens during the first trip handle in
thermal_zone_device_register():
kernel: thermal thermal_zone15: critical temperature reached (101 C), shutting down
However, we shouldn't do a thermal shutdown here, since
1) We may want to use a dedicated daemon, Intel's thermald in this case,
to handle thermal shutdown.
2) For ACPI based system, _CRT doesn't mean shutdown unless it's inside
ThermalZone namespace. ACPI Spec, 11.4.4 _CRT (Critical Temperature):
"... If this object it present under a device, the device’s driver
evaluates this object to determine the device’s critical cooling
temperature trip point. This value may then be used by the device’s
driver to program an internal device temperature sensor trip point."
So a "critical trip" here merely means we should take a more aggressive
cooling method.
As int340x device isn't present under ACPI ThermalZone, override the
default .critical callback to prevent surprising thermal shutdown.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201221172345.36976-1-kai.heng.feng@canonical.com
The function thermal_zone_device_reset() is called in the
thermal_zone_device_register() which allocates and initialize the
structure. The passive field is already zero-ed by the allocation, the
function is useless.
Call directly thermal_zone_device_init() instead and
thermal_zone_device_reset().
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201222181110.1231977-1-daniel.lezcano@linaro.org
The code does no longer use the ms unit based fields to set the
delays as they are replaced by the jiffies.
Remove them and replace their user to use the jiffies version instead.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Peter Kästle <peter@piie.net>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201216220337.839878-3-daniel.lezcano@linaro.org
The delays are also stored in jiffies based unit. Use them instead of
the ms.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201216220337.839878-2-daniel.lezcano@linaro.org
The delays are stored in ms units and when the polling function is
called this delay is converted into jiffies at each call.
Instead of doing the conversion again and again, compute the jiffies
at init time and use the value directly when setting the polling.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201216220337.839878-1-daniel.lezcano@linaro.org
The last site calling the thermal_zone_bind_cooling_device() function
with the THERMAL_TRIPS_NONE parameter was removed.
We can get rid of this test as no user of this function is calling
this function with this parameter.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-5-daniel.lezcano@linaro.org
The functions thermal_zone_device_rebind_exception and
thermal_zone_device_unbind_exception are not used from anywhere.
Remove that code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-2-daniel.lezcano@linaro.org
The code was reorganized in 2012 with the commit 0c01ebbfd3.
The main change is a loop on the trip points array and a unconditional
call to the throttle() ops of the governors for each of them even if
the trip temperature is not reached yet.
With this change, the 'forced_passive' is no longer checked in the
thermal_zone_device_update() function but in the step wise governor's
throttle() callback.
As the force_passive does no belong to the trip point array, the
thermal_zone_device_update() can not compare with the specified
passive temperature, thus does not detect the passive limit has been
crossed. Consequently, throttle() is never called and the
'forced_passive' branch is unreached.
In addition, the default processor cooling device is not automatically
bound to the thermal zone if there is not passive trip point, thus the
'forced_passive' can not operate.
If there is an active trip point, then the throttle function will be
called to mitigate at this temperature and the 'forced_passive' will
override the mitigation of the active trip point in this case but with
the default cooling device bound to the thermal zone, so usually a
fan, and that is not a passive cooling effect.
Given the regression exists since more than 8 years, nobody complained
and at the best of my knowledge there is no bug open in
https://bugzilla.kernel.org, it is reasonable to say it is unused.
Remove the 'forced_passive' related code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Thara Gopinath <thara.gopinath@linaro.org>
Link: https://lore.kernel.org/r/20201214233811.485669-1-daniel.lezcano@linaro.org
Several parts of the kernel are already using the effective CPU
utilization (as seen by the scheduler) to get the current load on the
CPU, do the same here instead of depending on the idle time of the CPU,
which isn't that accurate comparatively.
This is also the right thing to do as it makes the cpufreq governor
(schedutil) align better with the cpufreq_cooling driver, as the power
requested by cpufreq_cooling governor will exactly match the next
frequency requested by the schedutil governor since they are both using
the same metric to calculate load.
This was tested on ARM Hikey6220 platform with hackbench, sysbench and
schbench. None of them showed any regression or significant
improvements. Schbench is the most important ones out of these as it
creates the scenario where the utilization numbers provide a better
estimate of the future.
Scenario 1: The CPUs were mostly idle in the previous polling window of
the IPA governor as the tasks were sleeping and here are the details
from traces (load is in %):
Old: thermal_power_cpu_get_power: cpus=00000000,000000ff freq=1200000 total_load=203 load={{0x35,0x1,0x0,0x31,0x0,0x0,0x64,0x0}} dynamic_power=1339
New: thermal_power_cpu_get_power: cpus=00000000,000000ff freq=1200000 total_load=600 load={{0x60,0x46,0x45,0x45,0x48,0x3b,0x61,0x44}} dynamic_power=3960
Here, the "Old" line gives the load and requested_power (dynamic_power
here) numbers calculated using the idle time based implementation, while
"New" is based on the CPU utilization from scheduler.
As can be clearly seen, the load and requested_power numbers are simply
incorrect in the idle time based approach and the numbers collected from
CPU's utilization are much closer to the reality.
Scenario 2: The CPUs were busy in the previous polling window of the IPA
governor:
Old: thermal_power_cpu_get_power: cpus=00000000,000000ff freq=1200000 total_load=800 load={{0x64,0x64,0x64,0x64,0x64,0x64,0x64,0x64}} dynamic_power=5280
New: thermal_power_cpu_get_power: cpus=00000000,000000ff freq=1200000 total_load=708 load={{0x4d,0x5c,0x5c,0x5b,0x5c,0x5c,0x51,0x5b}} dynamic_power=4672
As can be seen, the idle time based load is 100% for all the CPUs as it
took only the last window into account, but in reality the CPUs aren't
that loaded as shown by the utilization numbers.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lkml.kernel.org/r/9c255c83d78d58451abc06848001faef94c87a12.1607400596.git.viresh.kumar@linaro.org
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl/cYxEACgkQqDIjiipP
6E//swf+NQe5V9ioQ7j4wshFJLwIfu7uV0pNeTx3aHGx2R03hYwtcIS21/77SAgB
3KQikcrblrT49oKyCfkzYRUmdTgweSFHj9wN9OWBsIStus2sTFho9EOmcpyX0KOJ
2QBiOvvD3+xlhSMiKelJ/3OohrHwYE9ZMMW9pL5bZKDXuHXBao2Y1s7ZB9EaaM11
p+Qo9m9E+Pbp4WdJX+AgTHYMyKpVZbbAY+hulSOWDIcOms05MtPF5glPhQQS9yfR
yS+xZVtS2G9LCkuMdbXBGEn7vKJeqjH2aJ21+UkpBQUFLQExXvitx2O3w7i0cbup
Q6j4CHTtDcXBKl9p1L5wjmjEM6hwMA==
=5VgU
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.11-2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fixlet from Daniel Lezcano:
"A trivial change which fell through the cracks:
Add Alder Lake support ACPI ids (Srinivas Pandruvada)"
* tag 'thermal-v5.11-2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: int340x: Support Alder Lake
Pull thermal updates from Daniel Lezcano:
- Add upper and lower limits clamps for the cooling device state in the
power allocator governor (Michael Kao)
- Add upper and lower limits support for the power allocator governor
(Lukasz Luba)
- Optimize conditions testing for the trip points (Bernard Zhao)
- Replace spin_lock_irqsave by spin_lock in hard IRQ on the rcar driver
(Tian Tao)
- Add MT8516 dt-bindings and device reset optional support (Fabien
Parent)
- Add a quiescent period to cool down the PCH when entering S0iX
(Sumeet Pawnikar)
- Use bitmap API instead of re-inventing the wheel on sun8i (Yangtao
Li)
- Remove useless NULL check in the hwmon driver (Bernard Zhao)
- Update the current state in the cpufreq cooling device only if the
frequency change is effective (Zhuguangqing)
- Improve the schema validation for the rcar DT bindings (Geert
Uytterhoeven)
- Fix the user time unit in the documentation (Viresh Kumar)
- Add PCI ids for Lewisburg PCH (Andres Freund)
- Add hwmon support on amlogic (Martin Blumenstingl)
- Fix build failure for PCH entering on in S0iX (Randy Dunlap)
- Improve the k_* coefficient for the power allocator governor (Lukasz
Luba)
- Fix missing const on a sysfs attribute (Rikard Falkeborn)
- Remove broken interrupt support on rcar to be replaced by a new one
(Niklas Söderlund)
- Improve the error code handling at init time on imx8mm (Fabio
Estevam)
- Compute interval validity once instead at each temperature reading
iteration on acerhdf (Daniel Lezcano)
- Add r8a779a0 support (Niklas Söderlund)
- Add PCI ids for AlderLake PCH and mmio refactoring (Srinivas
Pandruvada)
- Add RFIM and mailbox support on int340x (Srinivas Pandruvada)
- Use macro for temperature calculation on PCH (Sumeet Pawnikar)
- Simplify return conditions at probe time on Broadcom (Zheng Yongjun)
- Fix workload name on PCH (Srinivas Pandruvada)
- Migrate the devfreq cooling device code to the energy model API
(Lukasz Luba)
- Emit a warning if the thermal_zone_device_update is called without
the .get_temp() ops (Daniel Lezcano)
- Add critical and hot ops for the thermal zone (Daniel Lezcano)
- Remove notification usage when critical is reached on rcar (Daniel
Lezcano)
- Fix devfreq build when ENERGY_MODEL is not set (Lukasz Luba)
* tag 'thermal-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (45 commits)
thermal/drivers/devfreq_cooling: Fix the build when !ENERGY_MODEL
thermal/drivers/rcar: Remove notification usage
thermal/core: Add critical and hot ops
thermal/core: Emit a warning if the thermal zone is updated without ops
drm/panfrost: Register devfreq cooling and attempt to add Energy Model
thermal: devfreq_cooling: remove old power model and use EM
thermal: devfreq_cooling: add new registration functions with Energy Model
thermal: devfreq_cooling: use a copy of device status
thermal: devfreq_cooling: change tracing function and arguments
thermal: int340x: processor_thermal: Correct workload type name
thermal: broadcom: simplify the return expression of bcm2711_thermal_probe()
thermal: intel: pch: use macro for temperature calculation
thermal: int340x: processor_thermal: Add mailbox driver
thermal: int340x: processor_thermal: Add RFIM driver
thermal: int340x: processor_thermal: Add AlderLake PCI device id
thermal: int340x: processor_thermal: Refactor MMIO interface
thermal: rcar_gen3_thermal: Add r8a779a0 support
dt-bindings: thermal: rcar-gen3-thermal: Add r8a779a0 support
platform/x86/drivers/acerhdf: Check the interval value when it is set
platform/x86/drivers/acerhdf: Use module_param_cb to set/get polling interval
...
Prevent build failure if the option CONFIG_ENERGY_MODEL is not set. The
devfreq cooling is able to operate without the Energy Model.
Don't use dev->em_pd directly and use local pointer.
Fixes: 615510fe13 ("thermal: devfreq_cooling: remove old power model and use EM")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201215154221.8828-1-lukasz.luba@arm.com
The ops is only showing a trace telling a critical trip point is
crossed. The same information is given by the thermal framework.
This is redundant, remove the code.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20201210121514.25760-4-daniel.lezcano@linaro.org
Currently there is no way to the sensors to directly call an ops in
interrupt mode without calling thermal_zone_device_update assuming all
the trip points are defined.
A sensor may want to do something special if a trip point is hot or
critical.
This patch adds the critical and hot ops to the thermal zone device,
so a sensor can directly invoke them or let the thermal framework to
call the sensor specific ones.
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20201210121514.25760-2-daniel.lezcano@linaro.org
The actual code is silently ignoring a thermal zone update when a
driver is requesting it without a get_temp ops set.
That looks not correct, as the caller should not have called this
function if the thermal zone is unable to read the temperature.
That makes the code less robust as the check won't detect the driver
is inconsistently using the thermal API and that does not help to
improve the framework as these circumvolutions hide the problem at the
source.
In order to detect the situation when it happens, let's add a warning
when the update is requested without the get_temp() ops set.
Any warning emitted will have to be fixed at the source of the
problem: the caller must not call thermal_zone_device_update if there
is not get_temp callback set.
Cc: Thara Gopinath <thara.gopinath@linaro.org>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Link: https://lore.kernel.org/r/20201210121514.25760-1-daniel.lezcano@linaro.org
Remove old power model and use new Energy Model to calculate the power
budget. It drops static + dynamic power calculations and power table
in order to use Energy Model performance domain data. This model
should be easy to use and could find more users. It is also less
complicated to setup the needed structures.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-5-lukasz.luba@arm.com
The Energy Model (EM) framework supports devices such as Devfreq. Create
new registration function which automatically register EM for the thermal
devfreq_cooling devices. This patch prepares the code for coming changes
which are going to replace old power model with the new EM.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-4-lukasz.luba@arm.com
Devfreq cooling needs to now the correct status of the device in order
to operate. Devfreq framework can change the device status in the
background. To mitigate issues make a copy of the status structure and use
it for internal calculations.
In addition this patch adds normalization function, which also makes sure
that whatever data comes from the device, the load will be in range from 1
to 1024.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-3-lukasz.luba@arm.com
Prepare for deleting the static and dynamic power calculation and clean
the trace function. These two fields are going to be removed in the next
changes.
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org> # for tracing code
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-2-lukasz.luba@arm.com
Use macro for temperature calculation
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210124801.13850-1-sumeet.r.pawnikar@intel.com
Added processor thermal device mail box interface for workload hints
setting. These hints will give indication to hardware to better manage
power and thermals. The supported hints are:
idle
semi_active
burusty
sustained
battery_life
For example when the system is on battery, the hardware can be less
aggressive in power ramp up.
This will create an attribute group at
/sys/bus/pci/devices/0000:00:04.0/workload_request
This folder contains two attributes:
workload_available_types : (RO): This shows available workload types
workload_type: (RW) : Allows to set and get current workload type
setting
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-4-srinivas.pandruvada@linux.intel.com
Add support for RFIM (Radio Frequency Interference Mitigation) support
via processor thermal PCI device. This drivers allows adjustment of
FIVR (Fully Integrated Voltage Regulator) and DDR (Double Data Rate)
frequencies to avoid RF interference with WiFi and 5G.
Switching voltage regulators (VR) generate radiated EMI or RFI at the
fundamental frequency and its harmonics. Some harmonics may interfere
with very sensitive wireless receivers such as Wi-Fi and cellular that
are integrated into host systems like notebook PCs. One of mitigation
methods is requesting SOC integrated VR (IVR) switching frequency to a
small % and shift away the switching noise harmonic interference from
radio channels. OEM or ODMs can use the driver to control SOC IVR
operation within the range where it does not impact IVR performance.
DRAM devices of DDR IO interface and their power plane can generate EMI
at the data rates. Similar to IVR control mechanism, Intel offers a
mechanism by which DDR data rates can be changed if several conditions
are met: there is strong RFI interference because of DDR; CPU power
management has no other restriction in changing DDR data rates;
PC ODMs enable this feature (real time DDR RFI Mitigation referred to as
DDR-RFIM) for Wi-Fi from BIOS.
This change exports two folders under /sys/bus/pci/devices/0000:00:04.0.
One folder "fivr" contains all attributes exposed for controling FIVR
features. The other folder "dvfs" contains all attributes for DDR
features.
Changes done to implement:
- New module for rfim interfaces
- Two new per processor features for DDR and FIVR
- Enable feature for Tiger Lake (FIVR only) and Alder Lake
The attributes exposed and explanation:
FIVR attributes
vco_ref_code_lo (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 3-bit LSB field.
vco_ref_code_hi (RW): The VCO reference code is an 11-bit field and
controls the FIVR switching frequency. This is the 8-bit MSB field.
spread_spectrum_pct (RW): Set the FIVR spread spectrum clocking
percentage
spread_spectrum_clk_enable (RW): Enable/disable of the FIVR spread
spectrum clocking feature
rfi_vco_ref_code (RW): This field is a read only status register which
reflects the current FIVR switching frequency
fivr_fffc_rev (RW): This field indicated the revision of the FIVR HW.
DVFS attributes
rfi_restriction_run_busy (RW): Request the restriction of specific DDR
data rate and set this value 1. Self reset to 0 after operation.
rfi_restriction_err_code (RW): Values: 0 :Request is accepted, 1:Feature
disabled, 2: the request restricts more points than it is allowed
rfi_restriction_data_rate_Delta (RW): Restricted DDR data rate for RFI
protection: Lower Limit
rfi_restriction_data_rate_Base (RW): Restricted DDR data rate for RFI
protection: Upper Limit
ddr_data_rate_point_0 (RO): DDR data rate selection 1st point
ddr_data_rate_point_1 (RO): DDR data rate selection 2nd point
ddr_data_rate_point_2 (RO): DDR data rate selection 3rd point
ddr_data_rate_point_3 (RO): DDR data rate selection 4th point
rfi_disable (RW): Disable DDR rate change feature
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-3-srinivas.pandruvada@linux.intel.com
Added AlderLake PCI device id to support processor thermal driver. Reuse
the feature set (just includes RAPL) from previous generations.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-2-srinivas.pandruvada@linux.intel.com
The Processor Thermal PCI device supports multiple features. Currently
we export only RAPL. But we need more features from this device exposed
for Tiger Lake and Alder Lake based platforms. So re-structure the
current MMIO interface, so that more features can be added cleanly.
No functional changes are expected with this change.
Changes done in this patch:
- Using PCI_DEVICE_DATA(), hence names of defines changed
- Move RAPL MMIO code to its own module
- Move the RAPL MMIO offsets to RAPL MMIO module
- Adjust Kconfig dependency of PROC_THERMAL_MMIO_RAPL
- Per processor driver data now contains the supported features
- Moved all the common data structures and defines to a common header
file
- This new header file contains all the processor_thermal_* interfaces
- Based on the features supported the module interface is called
- Each module atleast provides one add and one remove function
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126171829.945969-1-srinivas.pandruvada@linux.intel.com
Currently the error message does not print the correct error code.
Fix it by initializing 'ret' to the proper error code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201202232448.2692-1-festevam@gmail.com
Remove the usage of interrupts for the normal temperature operation and
depend on the polling performed by the thermal core. This is done to
prepare to use the interrupts as they are intended to trigger once
specific trip points are passed and not to react to temperature changes
in the normal operational range.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201126220923.3107213-1-niklas.soderlund+renesas@ragnatech.se
The only usage of these structs is to assign their address to the
thermal_zone_attribute_groups array, which consists of pointers to
const, so make them const to allow the compiler to put them in read-only
memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201128234342.36684-1-rikard.falkeborn@gmail.com
The PID coefficients should be estimated again when there was a change to
sustainable power value made by user. This change removes unused argument
'force' and makes the function ready for such updates.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-4-lukasz.luba@arm.com
The sustainable power value might come from the Device Tree or can be
estimated in run time. The sustainable power might be updated by the user
via sysfs interface, which should trigger new estimation of PID
coefficients. There is no need to estimate it every time when the
governor is called and temperature is high. Instead, store the estimated
value and make it available via standard sysfs interface, so it can be
checked from the user-space.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-3-lukasz.luba@arm.com
Intelligent Power Allocation (IPA) is built around the PID controller
concept. The initialization code tries to setup the environment based on
the information available in DT or estimate the value based on minimum
power reported by each of the cooling device. The estimation will have an
impact on the PID controller behaviour via the related 'k_po', 'k_pu',
'k_i' coefficients and also on the power budget calculation.
This change prevents the situation when 'k_i' is relatively big compared
to 'k_po' and 'k_pu' values. This might happen when the estimation for
'sustainable_power' returned small value, thus 'k_po' and 'k_pu' are
small.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Reviewed-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201124161025.27694-2-lukasz.luba@arm.com
The reference to acpi_gbl_FADT causes a build error when ACPI is not
enabled. Fix by making that conditional on CONFIG_ACPI.
../drivers/thermal/intel/intel_pch_thermal.c: In function 'pch_wpt_suspend':
../drivers/thermal/intel/intel_pch_thermal.c:217:8: error: 'acpi_gbl_FADT' undeclared (first use in this function); did you mean 'acpi_get_type'?
if (!(acpi_gbl_FADT.flags & ACPI_FADT_LOW_POWER_S0))
^~~~~~~~~~~~~
Fixes: ef63b043ac ("thermal: intel: pch: fix S0ix failure due to PCH temperature above threshold")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Amit Kucheria <amitk@kernel.org>
Cc: linux-pm@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201117023807.8266-1-rdunlap@infradead.org
Many monitoring tools read the CPU temperature using the hwmon
interface. Expose the thermal sensors on Amlogic boards as hwmon
devices.
Without this lm_sensors' "sensors" tool does not find any temperature
sensors. Now it prints:
cpu_thermal-virtual-0
Adapter: Virtual device
temp1: +44.7 C (crit = +110.0 C)
ddr_thermal-virtual-0
Adapter: Virtual device
temp1: +45.9 C (crit = +110.0 C)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201115190658.631578-1-martin.blumenstingl@googlemail.com
I noticed that I couldn't read the PCH temperature on my workstation
(C620 series chipset, w/ 2x Xeon Gold 5215 CPUs) directly, but had to go
through IPMI. Looking at the data sheet, it looks to me like the
existing intel PCH thermal driver should work without changes for
Lewisburg.
I suspect there's some other PCI IDs missing. But I hope somebody at
Intel would have an easier time figuring that out than I...
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: Tushar Dave <tushar.n.dave@intel.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Link: https://lore.kernel.org/lkml/20200115184415.1726953-1-andres@anarazel.de/
Signed-off-by: Andres Freund <andres@anarazel.de>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201113204916.1144907-1-andres@anarazel.de
It has been observed that on OMAP4430 (ES2.0, ES2.1 and ES2.3) the enabled
notifier causes errors on the DTEMP readout values:
ti-soc-thermal 4a002260.bandgap: in range ADC val: 52
ti-soc-thermal 4a002260.bandgap: in range ADC val: 64
ti-soc-thermal 4a002260.bandgap: in range ADC val: 64
ti-soc-thermal 4a002260.bandgap: out of range ADC val: 0
thermal thermal_zone0: failed to read out thermal zone (-5)
ti-soc-thermal 4a002260.bandgap: out of range ADC val: 0
thermal thermal_zone0: failed to read out thermal zone (-5)
ti-soc-thermal 4a002260.bandgap: out of range ADC val: 4
thermal thermal_zone0: failed to read out thermal zone (-5)
ti-soc-thermal 4a002260.bandgap: in range ADC val: 100
raw 100 translates to 133 Celsius on omap4-sdp, triggering shutdown due to
critical temperature.
When the notifier is disable for OMAP4430 the DTEMP values are stable:
ti-soc-thermal 4a002260.bandgap: in range ADC val: 56
ti-soc-thermal 4a002260.bandgap: in range ADC val: 56
ti-soc-thermal 4a002260.bandgap: in range ADC val: 57
ti-soc-thermal 4a002260.bandgap: in range ADC val: 57
ti-soc-thermal 4a002260.bandgap: in range ADC val: 56
Fixes: 5093402e5b ("thermal: ti-soc-thermal: Enable addition power management")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201029100335.27665-1-peter.ujfalusi@ti.com
If state has not changed successfully and we updated cpufreq_state,
next time when the new state is equal to cpufreq_state (not changed
successfully last time), we will return directly and miss a
freq_qos_update_request() that should have been.
Fixes: 5130802ddb ("thermal: cpu_cooling: Switch to QoS requests for freq limits")
Cc: v5.4+ <stable@vger.kernel.org> # v5.4+
Signed-off-by: Zhuguangqing <zhuguangqing@xiaomi.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106092243.15574-1-zhuguangqing83@gmail.com
Function thermal_add_hwmon_sysfs, hwmon will be NULL when
new_hwmon_device = 0, so there is no need to check, kfree will
handle NULL point.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201102023121.3312-1-bernard@vivo.com
The bitmap_* API is the standard way to access data in the bitfield.
So convert irq_ack to return an unsigned long, and make things to use
bitmap API.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201109114624.23035-1-frank@allwinnertech.com
When system tries to enter S0ix suspend state, just after active load
scenarios, it fails due to PCH current temperature is higher than set
threshold.
This patch introduces delay loop mechanism that allows PCH temperature
to go down below threshold during suspend so it won't fail to enter S0ix.
Add delay loop timeout and count as module parameters for user to tune it,
if required based on system design. This change notifies the different
warning messages like when PCH temperature above the threshold and
executing delay loop. Also, notify the messages when it success or
failure for S0ix entry.
Previously out of 1000 runs around 3 to 5 times it might fail to enter
S0ix just after heavy workload. With this change, S0ix failures reduced
as PCH cools down below threshold.
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Reviewed-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201106170633.20838-1-sumeet.r.pawnikar@intel.com
MT8516 does not support thermal reset. Use device_reset_optional
instead of device_reset.
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201021164231.3029956-3-fparent@baylibre.com
On RT or even on mainline with 'threadirqs' on the command line all
interrupts which are not explicitly requested with IRQF_NO_THREAD
run their handlers in thread context. The same applies to soft interrupts.
That means they are subject to the normal scheduler rules and no other
code is going to acquire that lock from hard interrupt context either,
so the irqsave() here is pointless in all cases.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1603760790-37748-1-git-send-email-tiantao6@hisilicon.com
The trip points are checked one by one with multiple condition
branches where one condition is enough to disable the trip point.
Merge all these conditions in a single 'OR' statement.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201027013743.62392-1-bernard@vivo.com
[dlezcano] Changed patch description
Since the power actor section has one function power_actor_set_power()
move it into Intelligent Power Allocation (IPA). There is no other user
of that helper function. It would also allow to remove the check of
cdev_is_power_actor() because the code which calls it in IPA already does
the needed check. Make the function static since only IPA use it.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-5-lukasz.luba@arm.com
Since the Intelligent Power Allocation (IPA) uses different way to get
minimum and maximum power for a given cooling device, the helper functions
are not needed. There is no other code which uses them, so remove the
helper functions.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-4-lukasz.luba@arm.com
The thermal cooling device specified in DT might be instantiated for
a thermal zone trip point with a limited set of OPPs to operate on. This
configuration should be supported by Intelligent Power Allocation (IPA),
since it is a standard for other governors. Change the code and allow IPA
to get power value of lower and upper bound set for a given cooling
device.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201015112441.4056-3-lukasz.luba@arm.com
The upper and lower limits of thermal throttle state in the
DT do not apply to the Intelligent Power Allocation (IPA) governor.
Add the clamping for cooling device upper and lower limits in the
power_actor_set_power() used by IPA.
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Reviewed-by: Lukasz Luba <lukasz.luba@arm.com>
Tested-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201007024332.30322-1-michael.kao@mediatek.com
Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.
Remove the quote operator # from compiler_attributes.h __section macro.
Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.
Conversion done using the script at:
https://lore.kernel.org/lkml/75393e5ddc272dc7403de74d645e6c6e0f4e70eb.camel@perches.com/2-convert_section.pl
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@gooogle.com>
Reviewed-by: Miguel Ojeda <ojeda@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Use dev_error_probe() to simplify the error handling on imx and imx8
platforms (Anson Huang)
- Use dedicated kobj_to_dev() instead of container_of() in the sysfs
core code (Tian Tao)
- Fix coding style by adding braces to a one line conditional
statement on rcar (Geert Uytterhoeven)
- Add DT binding documentation for the r8a774e1 platform and update
the Kconfig description supporting RZ/G2 SoCs (Lad Prabhakar)
- Simplify the return expression of stm_thermal_prepare on the stm32
platform (Qinglang Miao)
- Fix the unit in the function documentation for the idle injection
cooling device (Zhuguang Qing)
- Remove an unecessary mutex_init() in the core code (Qinglang Miao)
- Add support for keep alive events in the core code and the specific
int340x (Srinivas Pandruvada)
- Remove unused thermal zone variable in devfreq and cpufreq cooling
devices (Zhuguang Qing)
- Add the A100's THS controller support (Yangtao Li)
- Add power management on the omap3's bandgap sensor (Adam Ford)
- Fix a missing nlmsg_free in the netlink core error path (Jing Xiangfeng)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl+GwbYACgkQqDIjiipP
6E8IFAf/UnO1HqfK96FnVJXx5ClXFE8PQhdVejxBEsNCJqUOwlqfpyONy7mgwABb
EuOvp5ZLX6ly9xG6J4NJhE4gN4DxqRKe0S3bQMU+DX8TQHc3otDKHILJbHrJdOY+
BYZpGxuCjU9yZrsJopztZIcpG7cF78d39XCJVSrBhoOBqPLXNGZkUUzOv9+QQti3
ipdhqB3kUzkgDFgIrDxX8t0vybQZSbiRWNUGrw/WQjMsG0NGIarCUHW4wiaea6gU
L2x1QDR5h9hxEAJiTBarOtF7ZlE15fpria0mWfTgmNMArMEtRBL60kBnmYa4o3EG
CseR7x1MdTCSqLCzKGfQyKv5SFgnVg==
=P6zv
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Fix Kconfig typo "acces" -> "access" (Colin Ian King)
- Use dev_error_probe() to simplify the error handling on imx and imx8
platforms (Anson Huang)
- Use dedicated kobj_to_dev() instead of container_of() in the sysfs
core code (Tian Tao)
- Fix coding style by adding braces to a one line conditional statement
on rcar (Geert Uytterhoeven)
- Add DT binding documentation for the r8a774e1 platform and update the
Kconfig description supporting RZ/G2 SoCs (Lad Prabhakar)
- Simplify the return expression of stm_thermal_prepare on the stm32
platform (Qinglang Miao)
- Fix the unit in the function documentation for the idle injection
cooling device (Zhuguang Qing)
- Remove an unecessary mutex_init() in the core code (Qinglang Miao)
- Add support for keep alive events in the core code and the specific
int340x (Srinivas Pandruvada)
- Remove unused thermal zone variable in devfreq and cpufreq cooling
devices (Zhuguang Qing)
- Add the A100's THS controller support (Yangtao Li)
- Add power management on the omap3's bandgap sensor (Adam Ford)
- Fix a missing nlmsg_free in the netlink core error path (Jing
Xiangfeng)
* tag 'thermal-v5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: core: Adding missing nlmsg_free() in thermal_genl_sampling_temp()
thermal: ti-soc-thermal: Enable addition power management
thermal: sun8i: Add A100's THS controller support
thermal: sun8i: add TEMP_CALIB_MASK for calibration data in sun50i_h6_ths_calibrate
dt-bindings: thermal: sun8i: Add binding for A100's THS controller
thermal: cooling: Remove unused variable *tz
thermal: int340x: Add keep alive response method
thermal: core: Add new event for sending keep alive notifications
thermal: int340x: Provide notification for OEM variable change
thermal: core: remove unnecessary mutex_init()
thermal/idle_inject: Fix comment of idle_duration_us and name of latency_ns
thermal: Kconfig: Update description for RCAR_GEN3_THERMAL config
thermal: stm32: simplify the return expression of stm_thermal_prepare()
dt-bindings: thermal: rcar-gen3-thermal: Add r8a774e1 support
thermal: rcar_thermal: Add missing braces to conditional statement
thermal: Use kobj_to_dev() instead of container_of()
thermal: imx8mm: Use dev_err_probe() to simplify error handling
thermal: imx: Use dev_err_probe() to simplify error handling
drivers: thermal: Kconfig: fix spelling mistake "acces" -> "access"
thermal_genl_sampling_temp() misses to call nlmsg_free() in an error path.
Jump to out_free to fix it.
Fixes: 1ce50e7d40 ("thermal: core: genetlink support for events/cmd/sampling")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200929082652.59876-1-jingxiangfeng@huawei.com
The bandgap sensor can be idled when the processor is too, but it
isn't currently being done, so the power consumption of OMAP3
boards can elevated if the bangap sensor is enabled.
This patch attempts to use some additional power management
to idle the clock to the bandgap when not needed.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Tested-by: Andreas Kemnade <andreas@kemnade.info> # GTA04
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200911123157.759379-1-aford173@gmail.com
For sun50i_h6_ths_calibrate(), the data read from nvmem needs a round of
calculation. On the other hand, the newer SOC may store other data in
the space other than 12bit sensor data. Add mask operation to read data
to avoid conversion error.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/dcf98648c16aff7649ff82438bfce6caae3e176f.1595572867.git.frank@allwinnertech.com
1. devfreq_cooling.c: The variable *tz is not used in
devfreq_cooling_get_requested_power(), devfreq_cooling_state2power()
and devfreq_cooling_power2state().
2. cpufreq_cooling.c: After 84fe2cab48, the variable *tz is not used
anymore in cpufreq_get_requested_power(), cpufreq_state2power() and
cpufreq_power2state().
Remove the variable *tz.
Signed-off-by: zhuguangqing <zhuguangqing@xiaomi.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200914071101.13575-1-zhuguangqing83@gmail.com
When firmware requests keep alive response, send an event to user space
to confirm by using imok sysfs entry.
Create a new sysf entry called "imok". User space can write an integer,
which results in execution of IMOK ACPI method of INT3400 thermal zone
device. This results in sending response to firmware request for keep
alive.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-4-srinivas.pandruvada@linux.intel.com
When we receive ACPI notification for OEM variable change pass the
notification to user space handler. This will avoid polling for
OEM variable change from user space.
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200915223650.406046-2-srinivas.pandruvada@linux.intel.com
The mutex poweroff_lock is initialized statically. It is
unnecessary to initialize by mutex_init().
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200916062139.191233-1-miaoqinglang@huawei.com
According to Documentation/process/coding-style.rst, if one branch of a
conditional statement needs braces, both branches should use braces.
Fixes: bbcf90c064 ("thermal: Explicitly enable non-changing thermal zone devices")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200819092716.3191-1-geert+renesas@glider.be
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-2-git-send-email-Anson.Huang@nxp.com
dev_err_probe() can reduce code size, uniform error handling and record the
defer probe reason etc., use it to simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1597129185-8460-1-git-send-email-Anson.Huang@nxp.com
Bulk of the genetlink users can use smaller ops, move them.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We want to add maxattr and policy back to genl_ops, to enable
dumping per command policy to user space. This, however, would
cause bloat for all the families with global policies. Introduce
smaller version of ops (half the size of genl_ops). Translate
these smaller ops into a full blown struct before use in the
core.
v1:
- use struct assignment
- put a full copy of the op in struct genl_dumpit_info
- s/light/small/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
resulting from an incorrect ADC conversion are too high and fire an
emergency shutdown (Tony Lindgren)
- Don't suppress negative temp for qcom spmi as they are valid and
userspace needs them (Veera Vegivada)
- Fix use-after-free in thermal_zone_device_unregister reported by
Kasan (Dmitry Osipenko)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl9SDqQACgkQqDIjiipP
6E9/qwf/WybOihgjeQUv3a9f4k6SeJphoDZRNATJtyU1e+fgJXUxjFqma6t4CYJv
uphZ1SppY9rnx1nWzhANSQjKun5KLwIskcNTCaGN4adRJ1cNdY63PdSX9BTJr9+H
w5H0AGWMErAOdmCPCro4pnZ3l3FPKXcoNvqDAjF1kZ97v5tMGzdInflOJl1ztUZA
scAnY7j0TyNsoRy2TV0oxQtSN9cDhgph1zJF1RcVzlU1uD897Htet1RF/PrHDvBW
NYVcWDTfiWmvf9Zewy2+cfApK9QGqBRhnwt4Z8PlTUcqrOgqAiNnOAnov+Topg/y
XNQzWwXFUip6bk5pTXPF8gSI0glkJg==
=LDGk
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal fixes from Daniel Lezcano:
- Fix bogus thermal shutdowns for omap4430 where bogus values resulting
from an incorrect ADC conversion are too high and fire an emergency
shutdown (Tony Lindgren)
- Don't suppress negative temp for qcom spmi as they are valid and
userspace needs them (Veera Vegivada)
- Fix use-after-free in thermal_zone_device_unregister reported by
Kasan (Dmitry Osipenko)
* tag 'thermal-v5.9-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
thermal: core: Fix use-after-free in thermal_zone_device_unregister()
thermal: qcom-spmi-temp-alarm: Don't suppress negative temp
thermal: ti-soc-thermal: Fix bogus thermal shutdowns for omap4430
The user-after-free bug in thermal_zone_device_unregister() is reported by
KASAN. It happens because struct thermal_zone_device is released during of
device_unregister() invocation, and hence the "tz" variable shouldn't be
touched by thermal_notify_tz_delete(tz->id).
Fixes: 55cdf0a283 ("thermal: core: Add notifications call in the framework")
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200817235854.26816-1-digetx@gmail.com
Currently driver is suppressing the negative temperature
readings from the vadc. Consumers of the thermal zones need
to read the negative temperature too. Don't suppress the
readings.
Fixes: c610afaa21 ("thermal: Add QPNP PMIC temperature alarm driver")
Signed-off-by: Veera Vegivada <vvegivad@codeaurora.org>
Signed-off-by: Guru Das Srinagesh <gurus@codeaurora.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/944856eb819081268fab783236a916257de120e4.1596040416.git.gurus@codeaurora.org
We can sometimes get bogus thermal shutdowns on omap4430 at least with
droid4 running idle with a battery charger connected:
thermal thermal_zone0: critical temperature reached (143 C), shutting down
Dumping out the register values shows we can occasionally get a 0x7f value
that is outside the TRM listed values in the ADC conversion table. And then
we get a normal value when reading again after that. Reading the register
multiple times does not seem help avoiding the bogus values as they stay
until the next sample is ready.
Looking at the TRM chapter "18.4.10.2.3 ADC Codes Versus Temperature", we
should have values from 13 to 107 listed with a total of 95 values. But
looking at the omap4430_adc_to_temp array, the values are off, and the
end values are missing. And it seems that the 4430 ADC table is similar
to omap3630 rather than omap4460.
Let's fix the issue by using values based on the omap3630 table and just
ignoring invalid values. Compared to the 4430 TRM, the omap3630 table has
the missing values added while the TRM table only shows every second
value.
Note that sometimes the ADC register values within the valid table can
also be way off for about 1 out of 10 values. But it seems that those
just show about 25 C too low values rather than too high values. So those
do not cause a bogus thermal shutdown.
Fixes: 1a31270e54 ("staging: omap-thermal: add OMAP4 data structures")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706183338.25622-1-tony@atomide.com
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
- New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
- Driver Removal
- Remove unused driver for TI's SMSC ECE1099
- New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
- New Functionality
- Add support for AXP803 to be probed by I2C
- Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes; stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller
- Enabled Regmap 'fast I/O'; stm32-lptimer
- Change BUG_ON to WARN_ON; arizona-core
- Remove superfluous code/initialisation; madera, max14577
- Trivial formatting/spelling issues; madera-core, madera-i2c, da9055, max77693-private
- Switch to of_platform_populate(); sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros; lm3533-ctrlbank
- Disable IRQs on suspend; motorola-cpcap
- Clean-up error handling; intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices; madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique; syscon
- Bug Fixes
- Properly 'put' clock on unbind and error; arizona-core
- Fix revision handling; da9063
- Fix 'assignment of read-only location' error; kempld-core
- Avoid using the Regmap API when atomic; rn5t618
- Redefine volatile register description; rn5t618
- Use locking to protect event handler; dln2
-----BEGIN PGP SIGNATURE-----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=X/Zn
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Frameworks
- Make better attempt at matching device with the correct OF node
- Allow batch removal of hierarchical sub-devices
New Drivers
- Add STM32 Clocksource driver
- Add support for Khadas System Control Microcontroller
Driver Removal
- Remove unused driver for TI's SMSC ECE1099
New Device Support
- Add support for Intel Emmitsburg PCH to Intel LPSS PCI
- Add support for Intel Tiger Lake PCH-H to Intel LPSS PCI
- Add support for Dialog DA revision to Dialog DA9063
New Functionality
- Add support for AXP803 to be probed by I2C
Fix-ups
- Numerous W=1 warning fixes
- Device Tree changes (stm32-lptimer, gateworks-gsc, khadas,mcu, stmfx, cros-ec, j721e-system-controller)
- Enabled Regmap 'fast I/O' in stm32-lptimer
- Change BUG_ON to WARN_ON in arizona-core
- Remove superfluous code/initialisation (madera, max14577)
- Trivial formatting/spelling issues (madera-core, madera-i2c, da9055, max77693-private)
- Switch to of_platform_populate() in sprd-sc27xx-spi
- Expand out set/get brightness/pwm macros in lm3533-ctrlbank
- Disable IRQs on suspend in motorola-cpcap
- Clean-up error handling in intel_soc_pmic_mrfld
- Ensure correct removal order of sub-devices in madera
- Many s/HTTP/HTTPS/ link changes
- Ensure name used with Regmap is unique in syscon
Bug Fixes
- Properly 'put' clock on unbind and error in arizona-core
- Fix revision handling in da9063
- Fix 'assignment of read-only location' error in kempld-core
- Avoid using the Regmap API when atomic in rn5t618
- Redefine volatile register description in rn5t618
- Use locking to protect event handler in dln2"
* tag 'mfd-next-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (76 commits)
mfd: syscon: Use a unique name with regmap_config
mfd: Replace HTTP links with HTTPS ones
mfd: dln2: Run event handler loop under spinlock
mfd: madera: Improve handling of regulator unbinding
mfd: mfd-core: Add mechanism for removal of a subset of children
mfd: intel_soc_pmic_mrfld: Simplify the return expression of intel_scu_ipc_dev_iowrite8()
mfd: max14577: Remove redundant initialization of variable current_bits
mfd: rn5t618: Fix caching of battery related registers
mfd: max77693-private: Drop a duplicated word
mfd: da9055: pdata.h: Drop a duplicated word
mfd: rn5t618: Make restart handler atomic safe
mfd: kempld-core: Fix 'assignment of read-only location' error
mfd: axp20x: Allow the AXP803 to be probed by I2C
mfd: da9063: Add support for latest DA silicon revision
mfd: da9063: Fix revision handling to correctly select reg tables
dt-bindings: mfd: st,stmfx: Remove I2C unit name
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller
mfd: motorola-cpcap: Disable interrupt for suspend
mfd: smsc-ece1099: Remove driver
mfd: core: Add OF_MFD_CELL_REG() helper
...
We just don't do that. "default y" is for things that are needed for
compatibility (when an old feature is made unconditional), or for things
that are basically part of the infrastructure of a platform.
And it can possibly be used for questions that don't enable code on
their own, but are used to enable or disable a whole slew of other
questions.
A new feature that people aren't using is never 'default y', unless it
cures cancer or ends world hunger.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events, temperature
and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8q7tsACgkQqDIjiipP
6E+5Rwf7BFEn5YXPvng8cmnAlgvEBc9DdT6mGSo0NpFm9MdUxXlaqvw3WWSGyqWQ
+z0Ka7lmn5XyiMsVN11++Snp+79X17HzZf9SXO3glyIpAn+5prTDRhzzj0/jPrtS
sEeI++DrILsKKMGVljzftLmwNJN9DkUDNcnmWmZdCDbYVEKtP9Pjf2wBjAnXj7sX
JA3CkHRMwYLEQbfaKz37M11cYM+LqbDOlb6U11YWgAGGJ7d7zNYRf2/YSYPM4AN6
iE6j0E+3jIlXesULsap1AzeJaBq+wFxj1FL2TUZ8KscvRrm3AucqzNAT2M/Bc5Az
XLKKzc6Gp9JfqB5KXhX2EDu7VRnDBg==
=cSMN
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add support to enable/disable the thermal zones resulting on core
code and drivers cleanup (Andrzej Pietrasiewicz)
- Add generic netlink support for userspace notifications: events,
temperature and discovery commands (Daniel Lezcano)
- Fix redundant initialization for a ret variable (Colin Ian King)
- Remove the clock cooling code as it is used nowhere (Amit Kucheria)
- Add the rcar_gen3_thermal's r8a774e1 support (Marian-Cristian
Rotariu)
- Replace all references to thermal.txt in the documentation to the
corresponding yaml files (Amit Kucheria)
- Add maintainer entry for the IPA (Lukasz Luba)
- Add support for MSM8939 for the tsens (Shawn Guo)
- Update power allocator and devfreq cooling to SPDX licensing (Lukasz
Luba)
- Add Cannon Lake Low Power PCH support (Sumeet Pawnikar)
- Add tsensor support for V2 mediatek thermal system (Henry Yen)
- Fix thermal zone lookup by ID for the core code (Thierry Reding)
* tag 'thermal-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (40 commits)
thermal: intel: intel_pch_thermal: Add Cannon Lake Low Power PCH support
thermal: mediatek: Add tsensor support for V2 thermal system
thermal: mediatek: Prepare to add support for other platforms
thermal: Update power allocator and devfreq cooling to SPDX licensing
MAINTAINERS: update entry to thermal governors file name prefixing
thermal: core: Add thermal zone enable/disable notification
thermal: qcom: tsens-v0_1: Add support for MSM8939
dt-bindings: tsens: qcom: Document MSM8939 compatible
thermal: core: Fix thermal zone lookup by ID
thermal: int340x: processor_thermal: fix: update Jasper Lake PCI id
thermal: imx8mm: Support module autoloading
thermal: ti-soc-thermal: Fix reversed condition in ti_thermal_expose_sensor()
MAINTAINERS: Add maintenance information for IPA
thermal: rcar_gen3_thermal: Do not shadow thcode variable
dt-bindings: thermal: Get rid of thermal.txt and replace references
thermal: core: Move initialization after core initcall
thermal: netlink: Improve the initcall ordering
net: genetlink: Move initialization to core_initcall
thermal: rcar_gen3_thermal: Add r8a774e1 support
thermal/drivers/clock_cooling: Remove clock_cooling code
...
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
* pm-em:
OPP: refactor dev_pm_opp_of_register_em() and update related drivers
Documentation: power: update Energy Model description
PM / EM: change name of em_pd_energy to em_cpu_energy
PM / EM: remove em_register_perf_domain
PM / EM: add support for other devices than CPUs in Energy Model
PM / EM: update callback structure and add device pointer
PM / EM: introduce em_dev_register_perf_domain function
PM / EM: change naming convention from 'capacity' to 'performance'
* pm-core:
mmc: jz4740: Use pm_ptr() macro
PM: Make *_DEV_PM_OPS macros use __maybe_unused
PM: core: introduce pm_ptr() macro
This patch adds full support for ver 2 thermal system (e.g., MT7622 SoC).
The new changes include reading calibration data, converting temperature
and hardware initialization which are specific for version 2 system.
Each platform decides which function to call according to its version.
Fixes: 3966be3c08 ("thermal: mediatek: add support for MT7622 SoC")
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1588238074-19338-3-git-send-email-henry.yen@mediatek.com
It is known that Mediatek owns two thermal systems, which only differ
in the way of reading calibration data and converting temperature.
MT8173, MT8183, MT2701 and MT2712 belongs to version 1 thermal
system, and MT7622 belongs to version 2.
In order to handle both systems, the suffix _V1 is appended to the
current code, and then the second patch will add _V2 functions with
the same purpose but different implementation.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1588238074-19338-2-git-send-email-henry.yen@mediatek.com
Now the calls to enable/disable a thermal zone are centralized in a
call to a function, we can add in these the corresponding netlink
notifications.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200727231033.26512-1-daniel.lezcano@linaro.org
The TSENS integrated on MSM8939 is a v0_1 device with 10 sensors.
Different from its predecessor MSM8916, where 'calib_sel' bits sit in
separate qfprom word, MSM8939 has 'cailb' and 'calib_sel' bits mixed and
spread on discrete offsets. That's why all qfprom bits are read as one
go and later mapped to calibration data for MSM8939.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Amit Kucheria <amit.kucheria@linaro.org>
Tested-by: Konrad Dybcio <konradybcio@gmail.com> /* on Asus Z00T smartphone */
Acked-by: Konrad Dybcio <konradybcio@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629144926.665-3-shawn.guo@linaro.org
When a thermal zone is looked up by an ID and no zone is found matching
that ID, the thermal_zone_get_by_id() function will return a pointer to
the thermal zone list head which isn't actually a valid thermal zone.
This can lead to a subsequent crash because a valid pointer is returned
to the called, but dereferencing that pointer as struct thermal_zone is
not safe.
Fixes: 329b064fbd ("thermal: core: Get thermal zone by id")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200724170105.2705467-1-thierry.reding@gmail.com
Update PCI device id for Jasper Lake processor thermal device.
With this proc_thermal driver is getting loaded and processor
thermal functionality works on Jasper Lake system.
Fixes: f64a6583d3 ("thermal: int340x: processor_thermal: Add Jasper Lake support")
Signed-off-by: Sumeet Pawnikar <sumeet.r.pawnikar@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1595577146-1221-1-git-send-email-sumeet.r.pawnikar@intel.com
This condition is reversed and will cause breakage.
Fixes: 7440f518da ("thermal/drivers/ti-soc-thermal: Avoid dereferencing ERR_PTR")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200616091949.GA11940@mwanda
The function rcar_gen3_thermal_calc_coefs() takes an argument called
'thcode' which shadows the static global 'thcode' variable. This is not
harmful but bad for readability and is harmful for planned changes to
the driver. The THCODE values should be read from hardware fuses if they
are available and only fallback to the global 'thcode' variable if they
are not fused.
Rename the global 'thcode' variable to 'thcodes' to avoid shadowing the
symbol in functions that take it as an argument.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200610003300.884258-1-niklas.soderlund+renesas@ragnatech.se
The generic netlink is initialized at subsys_initcall, so far after
the thermal init routine and the thermal generic netlink family
initialization.
On ŝome platforms, that leads to a memory corruption.
The fix was sent to netdev@ to move the genetlink framework
initialization at core_initcall.
Move the thermal core initialization to postcore level which is very
close to core level.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200717164217.18819-2-daniel.lezcano@linaro.org
The initcalls like to play joke. In our case, the thermal-netlink
initcall is called after the thermal-core initcall but this one sends
a notification before the former is initialized. No issue was spotted,
but it could lead to a memory corruption, so instead of relying on the
core_initcall for the thermal-netlink, let's initialize directly from
the thermal-core init routine, so we have full control of the init
ordering.
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200717164217.18819-1-daniel.lezcano@linaro.org
The variable ret is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706140747.489075-1-colin.king@canonical.com
When the network is not configured, the netlink is disabled on all
the system. The thermal framework assumed the netlink is always
opt-in.
Fix this by adding a Kconfig option for the netlink notification,
defaulting to yes and depending on CONFIG_NET.
As the change implies multiple stubs and in order to not pollute the
internal thermal header, the thermal_nelink.h has been added and
included in the thermal_core.h, so this one regain some kind of
clarity.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Link: https://lore.kernel.org/r/20200707090159.1018-1-daniel.lezcano@linaro.org
kernel panic (Bartosz Szczepanek)
- Fix debug message level to prevent flooding on some platform (Alex
Hung)
- Fix invalid bank access by reverting "thermal: mediatek: fix
register index error" (Enric Balletbo i Serra)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl8QFhUACgkQqDIjiipP
6E99Uwf+O+MIwd4epoWG6L3SYYaOJZpkmdYJoWIXxLZu5jGiS0uf48utaXVJrTSQ
5VXCoqd2alxzAE2ZveqEV2Lp558+rT7cRmWd6ZH6UPVEC2j+1TzVfcSwJRm8jrNN
lbmt2785wcUsfRzuHqfCEIDW6HTjfcGj4d+a8CJ4K/58CdhaxOxGgDK5Wsmmy/jF
Fkco37wUVw0Ew9cAuc2OwB8hOjDMtMnBZ4xoPSaptIVEyCUurl+c1JOxFkubOM0x
a7DyBS8zKM4UVGo7jaUXwC/28TUFDZNJD8E7H4JOJfVSqK5l3HKfjqeVE44cS2SJ
u9RvLCyQkp/+CC75MfIEEpqgDLHZcA==
=0Xzx
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux into master
Pull thermal fixes from Daniel Lezcano:
- Fix invalid index array access on int340x_thermal leading to a kernel
panic (Bartosz Szczepanek)
- Fix debug message level to prevent flooding on some platform (Alex
Hung)
- Fix invalid bank access by reverting "thermal: mediatek: fix register
index error" (Enric Balletbo i Serra)
* tag 'thermal-v5.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux:
Revert "thermal: mediatek: fix register index error"
thermal: int3403_thermal: Downgrade error message
thermal/int340x_thermal: Prevent page fault on .set_mode() op
Downgrade "Unsupported event" message from dev_err to dev_dbg to avoid
flooding with this message on some platforms.
Cc: stable@vger.kernel.org # v5.4+
Suggested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Alex Hung <alex.hung@canonical.com>
[ rzhang: fix typo in changelog ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200615223957.183153-1-alex.hung@canonical.com
Starting from commit "thermal/int340x_thermal: Don't require IDSP to
exist", priv->current_uuid_index is initialized to -1. This value may
be passed to int3400_thermal_run_osc() from int3400_thermal_set_mode,
contributing to page fault when accessing int3400_thermal_uuids array
at index -1.
This commit adds a check on uuid value to int3400_thermal_run_osc.
Fixes: 8d485da0dd ("thermal/int340x_thermal: Don't require IDSP to exist")
Signed-off-by: Bartosz Szczepanek <bsz@semihalf.com>
Reviewed-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
[ rzhang: Add Fixes tag ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200708134613.131555-1-bsz@semihalf.com
The generic netlink protocol is implemented but the different
notification functions are not yet connected to the core code.
These changes add the notification calls in the different
corresponding places.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200706105538.2159-4-daniel.lezcano@linaro.org
Initially the thermal framework had a very simple notification
mechanism to send generic netlink messages to the userspace.
The notification function was never called from anywhere and the
corresponding dead code was removed. It was probably a first attempt
to introduce the netlink notification.
At LPC2018, the presentation "Linux thermal: User kernel interface",
proposed to create the notifications to the userspace via a kfifo.
The advantage of the kfifo is the performance. It is usually used from
a 1:1 communication channel where a driver captures data and sends it
as fast as possible to a userspace process.
The drawback is that only one process uses the notification channel
exclusively, thus no other process is allowed to use the channel to
get temperature or notifications.
This patch defines a generic netlink API to discover the current
thermal setup and adds event notifications as well as temperature
sampling. As any genetlink protocol, it can evolve and the versioning
allows to keep the backward compatibility.
In order to prevent the user from getting flooded with data on a
single channel, there are two multicast channels, one for the
temperature sampling when the thermal zone is updated and another one
for the events, so the user can get the events only without the
thermal zone temperature sampling.
Also, a list of commands to discover the thermal setup is added and
can be extended when needed.
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200706105538.2159-3-daniel.lezcano@linaro.org
The next patch will introduce the generic netlink protocol to handle
events, sampling and command from the thermal framework. In order to
deal with the thermal zone, it uses its unique identifier to
characterize it in the message. Passing an integer is more efficient
than passing an entire string.
This change provides a function returning back a thermal zone pointer
corresponding to the identifier passed as parameter.
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200706105538.2159-2-daniel.lezcano@linaro.org
The cdev, tz and governor list, as well as their respective locks are
statically defined in the thermal_core.c file.
In order to give a sane access to these list, like browsing all the
thermal zones or all the cooling devices, let's define a set of
helpers where we pass a callback as a parameter to be called for each
thermal entity.
We keep the self-encapsulation and ensure the locks are correctly
taken when looking at the list.
Acked-by: Zhang Rui <rui.zhang@intel.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200706105538.2159-1-daniel.lezcano@linaro.org
set_mode() is only called when tzd's mode is about to change. Actual
setting is performed in thermal_core, in thermal_zone_device_set_mode().
The meaning of set_mode() callback is actually to notify the driver about
the mode being changed and giving the driver a chance to oppose such
change.
To better reflect the purpose of the method rename it to change_mode()
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-12-andrzej.p@collabora.com
Setting polling_delay is now done at thermal_core level (by not polling
DISABLED devices), so no need to repeat this code.
int340x: Checking for an impossible enum value is unnecessary.
acpi/thermal: It only prints debug messages.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-11-andrzej.p@collabora.com
Polling DISABLED devices is not desired, as all such "disabled" devices
are meant to be handled by userspace. This patch introduces and uses
should_stop_polling() to decide whether the device should be polled or not.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-10-andrzej.p@collabora.com
Some thermal zone devices never change their state, so they should be
always enabled.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-9-andrzej.p@collabora.com
Use thermal_zone_device_{en|dis}able() and thermal_zone_device_is_enabled().
Consequently, all set_mode() implementations in drivers:
- can stop modifying tzd's "mode" member,
- shall stop taking tzd's lock, as it is taken in the helpers
- shall stop calling thermal_zone_device_update() as it is called in the
helpers
- can assume they are called when the mode truly changes, so checks to
verify that can be dropped
Not providing set_mode() by a driver no longer prevents the core from
being able to set tzd's mode, so the relevant check in mode_store() is
removed.
Other comments:
- acpi/thermal.c: tz->thermal_zone->mode will be updated only after we
return from set_mode(), so use function parameter in thermal_set_mode()
instead, no need to call acpi_thermal_check() in set_mode()
- thermal/imx_thermal.c: regmap writes and mode assignment are done in
thermal_zone_device_{en|dis}able() and set_mode() callback
- thermal/intel/intel_quark_dts_thermal.c: soc_dts_{en|dis}able() are a
part of set_mode() callback, so they don't need to modify tzd->mode, and
don't need to fall back to the opposite mode if unsuccessful, as the return
value will be propagated to thermal_zone_device_{en|dis}able() and
ultimately tzd's member will not be changed in thermal_zone_device_set_mode().
- thermal/of-thermal.c: no need to set zone->mode to DISABLED in
of_parse_thermal_zones() as a tzd is kzalloc'ed so mode is DISABLED anyway
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-8-andrzej.p@collabora.com
Prepare for making the drivers not access tzd's private members.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
[staticize thermal_zone_device_set_mode()]
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-7-andrzej.p@collabora.com
get_mode() is now redundant, as the state is stored in struct
thermal_zone_device.
Consequently the "mode" attribute in sysfs can always be visible, because
it is always possible to get the mode from struct tzd.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
[for acerhdf]
Acked-by: Peter Kaestle <peter@piie.net>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200629122925.21729-6-andrzej.p@collabora.com
As description for DIV_ROUND_CLOSEST in file include/linux/kernel.h.
"Result is undefined for negative divisors if the dividend variable
type is unsigned and for negative dividends if the divisor variable
type is unsigned."
In current code, the FIXPT_DIV uses DIV_ROUND_CLOSEST but has not
checked sign of divisor before using. It makes undefined temperature
value in case the value is negative.
This patch fixes to satisfy DIV_ROUND_CLOSEST description
and fix bug too. Note that the variable name "reg" is not good
because it should be the same type as rcar_gen3_thermal_read().
However, it's better to rename the "reg" in a further patch as
cleanup.
Signed-off-by: Van Do <van.do.xw@renesas.com>
Signed-off-by: Dien Pham <dien.pham.ry@renesas.com>
[shimoda: minor fixes, add Fixes tag]
Fixes: 564e73d283 ("thermal: rcar_gen3_thermal: Add R-Car Gen3 thermal driver")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Niklas Soderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Niklas Soderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1593085099-2057-1-git-send-email-yoshihiro.shimoda.uh@renesas.com
The function cpu_power_to_freq is used to find a frequency and set the
cooling device to consume at most the power to be converted. For example,
if the power to be converted is 80mW, and the em table is as follow.
struct em_cap_state table[] = {
/* KHz mW */
{ 1008000, 36, 0 },
{ 1200000, 49, 0 },
{ 1296000, 59, 0 },
{ 1416000, 72, 0 },
{ 1512000, 86, 0 },
};
The target frequency should be 1416000KHz, not 1512000KHz.
Fixes: 349d39dc57 ("thermal: cpu_cooling: merge frequency and power tables")
Cc: <stable@vger.kernel.org> # v4.13+
Signed-off-by: Finley Xiao <finley.xiao@rock-chips.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200619090825.32747-1-finley.xiao@rock-chips.com
After merging tsens-common.c into tsens.c, we can now mark some
functions static so they don't need any prototype declarations. This
fixes the following issue reported by lkp.
>> drivers/thermal/qcom/tsens.c:385:13: warning: no previous prototype for 'tsens_critical_irq_thread' [-Wmissing-prototypes]
385 | irqreturn_t tsens_critical_irq_thread(int irq, void *data)
| ^~~~~~~~~~~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:455:13: warning: no previous prototype for 'tsens_irq_thread' [-Wmissing-prototypes]
455 | irqreturn_t tsens_irq_thread(int irq, void *data)
| ^~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:523:5: warning: no previous prototype for 'tsens_set_trips' [-Wmissing-prototypes]
523 | int tsens_set_trips(void *_sensor, int low, int high)
| ^~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:560:5: warning: no previous prototype for 'tsens_enable_irq' [-Wmissing-prototypes]
560 | int tsens_enable_irq(struct tsens_priv *priv)
| ^~~~~~~~~~~~~~~~
>> drivers/thermal/qcom/tsens.c:573:6: warning: no previous prototype for 'tsens_disable_irq' [-Wmissing-prototypes]
573 | void tsens_disable_irq(struct tsens_priv *priv)
| ^~~~~~~~~~~~~~~~~
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/6757a26876b29922929abf64b1c11fa3b3033d03.1590579709.git.amit.kucheria@linaro.org
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Fixes: 554fdbaf19 ("thermal: sprd: Add Spreadtrum thermal driver support")
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/1590371941-25430-1-git-send-email-yangtiezhu@loongson.cn
MT8183_NUM_ZONES should be set to 1
because MT8183 doesn't have multiple banks.
Fixes: a4ffe6b52d ("thermal: mediatek: add support for MT8183")
Signed-off-by: Michael Kao <michael.kao@mediatek.com>
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200323121537.22697-6-michael.kao@mediatek.com
The new Khadas VIM2 and VIM3 boards controls the cooling fan via the
on-board microcontroller.
This implements the FAN control as thermal devices and as cell of the Khadas
MCU MFD driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The Energy Model uses concept of performance domain and capacity states in
order to calculate power used by CPUs. Change naming convention from
capacity to performance state would enable wider usage in future, e.g.
upcoming support for other devices other than CPUs.
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Quentin Perret <qperret@google.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because SCHED_FIFO is a broken scheduler model (see previous patches)
take away the priority field, the kernel can't possibly make an
informed decision.
Effectively no change.
Cc: rafael.j.wysocki@intel.com
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Ingo Molnar <mingo@kernel.org>
- Thermal framework cleanups (self-encapsulation, pointless stubs,
private structures) (Daniel Lezcano)
- Use the PM QoS frequency changes for the devfreq cooling device (Matthias
Kaehlcke)
- Remove duplicate error messages from platform_get_irq() error handling
(Markus Elfring)
- Add support for the bandgap sensors (Keerthy)
- Statically initialize .get_mode/.set_mode ops (Andrzej Pietrasiewicz)
- Add Renesas R-Car maintainer entry (Niklas Söderlund)
- Fix error checking after calling ti_bandgap_get_sensor_data() for the TI SoC
thermal (Sudip Mukherjee)
- Add latency constraint for the idle injection, the DT binding and the change
the registering function (Daniel Lezcano)
- Convert the thermal framework binding to the Yaml schema (Amit Kucheria)
- Replace zero-length array with flexible-array on i.MX 8MM (Gustavo A. R. Silva)
- Thermal framework cleanups (alphabetic order for heads, replace module.h by
export.h, make file naming consistent) (Amit Kucheria)
- Merge tsens-common into the tsens driver (Amit Kucheria)
- Fix platform dependency for the Qoriq driver (Geert Uytterhoeven)
- Clean up the rcar_thermal_update_temp() function in the rcar thermal driver
(Niklas Söderlund)
- Fix the TMSAR register for the TMUv2 on the Qoriq platform (Yuantian Tang)
- Export GDDV, OEM vendor variables, and don't require IDSP for the int340x
thermal driver - trivial conflicts fixed (Matthew Garrett)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEGn3N4YVz0WNVyHskqDIjiipP6E8FAl7jra8ACgkQqDIjiipP
6E+ugAgApBF6FsHoonWIvoSrzBrrbU2oqhEJA42Mx+iY/UnXi01I79vZ/8WpZt7M
D1J01Kf0PUhRbywoKaoCX3Oh9ZO9PKq4N9ZC8yqdoD6GLl+rC9Wmr7Ui+c80klcv
M9rYhpPYfNXTFj0saSbbFWNNhP4TvhzGsNj8foYVQDKyhjbSmNE5ipZlbmP23jlr
O53SmJAwS5zxLOd8QA5nfSWP9FYYMuCR2AHj8BUCmxiAjXZLPNB/Hz2RRBr7q0MF
zRo/4HJ04mSQYp0kluP/EBhz9g2wM/htIPyWRveB/ByKEYt3UNKjB++PJmPbu5UG
dS3aXZhRfaPqpdsWrMB9fY7ll+oyfw==
=T+RI
-----END PGP SIGNATURE-----
Merge tag 'thermal-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Add the hwmon support on the i.MX SC (Anson Huang)
- Thermal framework cleanups (self-encapsulation, pointless stubs,
private structures) (Daniel Lezcano)
- Use the PM QoS frequency changes for the devfreq cooling device
(Matthias Kaehlcke)
- Remove duplicate error messages from platform_get_irq() error
handling (Markus Elfring)
- Add support for the bandgap sensors (Keerthy)
- Statically initialize .get_mode/.set_mode ops (Andrzej Pietrasiewicz)
- Add Renesas R-Car maintainer entry (Niklas Söderlund)
- Fix error checking after calling ti_bandgap_get_sensor_data() for the
TI SoC thermal (Sudip Mukherjee)
- Add latency constraint for the idle injection, the DT binding and the
change the registering function (Daniel Lezcano)
- Convert the thermal framework binding to the Yaml schema (Amit
Kucheria)
- Replace zero-length array with flexible-array on i.MX 8MM (Gustavo A.
R. Silva)
- Thermal framework cleanups (alphabetic order for heads, replace
module.h by export.h, make file naming consistent) (Amit Kucheria)
- Merge tsens-common into the tsens driver (Amit Kucheria)
- Fix platform dependency for the Qoriq driver (Geert Uytterhoeven)
- Clean up the rcar_thermal_update_temp() function in the rcar thermal
driver (Niklas Söderlund)
- Fix the TMSAR register for the TMUv2 on the Qoriq platform (Yuantian
Tang)
- Export GDDV, OEM vendor variables, and don't require IDSP for the
int340x thermal driver - trivial conflicts fixed (Matthew Garrett)
* tag 'thermal-v5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (48 commits)
thermal/int340x_thermal: Don't require IDSP to exist
thermal/int340x_thermal: Export OEM vendor variables
thermal/int340x_thermal: Export GDDV
thermal: qoriq: Update the settings for TMUv2
thermal: rcar_thermal: Clean up rcar_thermal_update_temp()
thermal: qoriq: Add platform dependencies
drivers: thermal: tsens: Merge tsens-common.c into tsens.c
thermal/of: Rename of-thermal.c
thermal/governors: Prefix all source files with gov_
thermal/drivers/user_space: Sort headers alphabetically
thermal/drivers/of-thermal: Sort headers alphabetically
thermal/drivers/cpufreq_cooling: Replace module.h with export.h
thermal/drivers/cpufreq_cooling: Sort headers alphabetically
thermal/drivers/clock_cooling: Include export.h
thermal/drivers/clock_cooling: Sort headers alphabetically
thermal/drivers/thermal_hwmon: Include export.h
thermal/drivers/thermal_hwmon: Sort headers alphabetically
thermal/drivers/thermal_helpers: Include export.h
thermal/drivers/thermal_helpers: Sort headers alphabetically
thermal/core: Replace module.h with export.h
...
The IDSP method doesn't appear to exist on the most recent Intel platforms:
instead, the IDSP data is included in the GDDV blob. Since we probably
don't want to decompress and parse that in-kernel, just allow any UUID to
be written if IDSP is missing.
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
[ rzhang: fix checkpatch warning in changelog ]
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-3-matthewgarrett@google.com
The platform vendor may expose an array of OEM-specific values to be used
in determining DPTF policy. These are obtained via the ODVP method, and
then simply exposed in sysfs. In addition, they are updated when a
notification is received or when the DPTF policy is changed by userland.
Conflicts:
drivers/thermal/intel/int340x_thermal/int3400_thermal.c
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-2-matthewgarrett@google.com
Implementing DPTF properly requires making use of firmware-provided
information associated with the INT3400 device. Calling GDDV provides a
buffer of information which userland can then interpret to determine
appropriate DPTF policy.
Conflicts:
drivers/thermal/intel/int340x_thermal/int3400_thermal.c
Signed-off-by: Matthew Garrett <mjg59@google.com>
Tested-by: Pandruvada, Srinivas <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Link: https://lore.kernel.org/r/20200414020953.255364-1-matthewgarrett@google.com
For TMU v2, TMSAR registers need to be set properly to get the
accurate temperature values.
Also the temperature read needs to be converted to degree Celsius
since it is in degrees Kelvin.
Signed-off-by: Yuantian Tang <andy.tang@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200526060212.4118-1-andy.tang@nxp.com
Moving the ctemp variable out of the private data structure made it
possible to clean up rcar_thermal_update_temp(). Initialize the local
ctemp to the error code to return if the reading fails and just return
it at the end of the function.
It's OK to change the datatype of old, new and ctemp to int as all
values are ANDed with CTEMP (0x3f) before being stored. While at it
change the datatype of the loop variable 'i' to to unsigned int.
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200514152505.1927634-1-niklas.soderlund+renesas@ragnatech.se
The QorIQ Thermal Monitoring Unit is only present on Freescale E500MC
and Layerscape SoCs, and on NXP i.MX8 SoCs. Add platform dependencies
to the QORIQ_THERMAL config symbol, to avoid asking the user about it
when configuring a kernel without support for any of the aforementioned
SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20200507112955.23520-5-geert+renesas@glider.be
tsens-common.c has outlived its usefuless. It was created expecting lots
of custom routines per version of the TSENS IP. We haven't needed those,
there is now only data in the version-specific files.
Merge the code for tsens-common.c into tsens.c. As a result,
- Remove any unnecessary forward declarations in tsens.h.
- Add a Linaro copyright to tsens.c.
- Fixup the Makefile to remove tsens-common.c.
- Where it made sense, fix some 80-column alignments in the
tsens-common.c code being copied over.
There is no functional change with this patch.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/e30e2ba6fa5c007983afd4d7d4e0311c0b57917a.1588183879.git.amit.kucheria@linaro.org
