Clean up the remainings of rtl_pll_power_down/up and rename
rtl_pll_power_down() to rtl_prepare_power_down().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Realtek provided a description of bits 6 and 7 in register PMCH.
They configure whether the chip powers down certain PLL in D3hot and
D3cold respectively. They do not actually power down the PLL.
Reflect this in the code and configure D3 PLL powerdown based on
whether WOL is enabled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There's no known reason why PLL powerdown on D3 shouldn't be enabled
on chip versions 34, 35, 36, and 42. At least the vendor driver doesn't
exclude any of these chip versions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
So far we don't increase the max read request size if we switch to
jumbo mode before bringing up the interface for the first time.
Let's change this.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Align behavior with r8168 vendor driver and don't reduce max read
request size for RTL8168e in jumbo mode.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8168dp is ancient anyway, and I haven't seen any trace of its early
version 27 yet. This chip versions needs quite some special handling,
therefore it would facilitate driver maintenance if support for it
could be dropped. For now just disable detection of this chip version.
If nobody complains we can remove support for it in the near future.
v2:
- extend unknown chip version error message
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/ca98f018-a0e1-8762-e95c-f0ad773a0271@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If WOL isn't enabled, then there's no need to enable wakeup from D3
on system shutdown.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use WARN_ONCE here to get a call trace in case of a problem.
This facilitates finding the offending code part.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Use WARN here to avoid stopping the system. In addition print the addr
and mask values that triggered the warning.
v2:
- return on WARN to avoid an invalid register write
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to Realtek the ERI register 0x1a8 quirk is needed to work
around a hw issue with the PHY on RTL8168g. The register needs to be
changed before powering down the PHY. Currently we don't meet this
requirement, however I'm not aware of any problems caused by this.
Therefore I see the change as an improvement.
The PHY driver has no means to access the chip ERI registers,
therefore we have to intercept MDIO writes to BMCR register.
If the BMCR_PDOWN bit is going to be set, then let's apply the
quirk before actually powering down the PHY.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
No functional change here. We just move a code block to avoid a
function forward declaration in a subsequent change.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After recent changes there's no need any longer to define NUM_RX_DESC
as an unsigned value.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's no need to check min(budget, NUM_RX_DESC). At first budget
(NAPI_POLL_WEIGHT = 64) is less then NUM_RX_DESC (256).
And more important: Even in case of budget > NUM_RX_DESC we could
safely continue processing descriptors as long as they are owned by
the CPU. In addition replace rx_left with a normal counter variable,
this allows to simplify the code. Last but not least there's no need
any longer to pass the budget as an u32.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some chip versions have a hw bug resulting in lost door bell rings.
To work around this the doorbell is also rung whenever we still have
tx descriptors in flight after having cleaned up tx descriptors.
These PCI(e) writes come at a cost, therefore let's reduce the number
of extra doorbell rings.
If skb is NULL then this means:
- last cleaned-up descriptor belongs to a skb with at least one fragment
and last fragment isn't marked as sent yet
- hw is in progress sending the skb, therefore no extra doorbell ring
is needed for this skb
- once last fragment is marked as transmitted hw will trigger
a tx done interrupt and we come here again (with skb != NULL)
and ring the doorbell if needed
Therefore skip the workaround doorbell ring if skb is NULL.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/0a15a83c-aecf-ab51-8071-b29d9dcd529a@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Improve the following in rtl8169_start_xmit:
- tp->cur_tx can be accessed in parallel by rtl_tx(), therefore
annotate the race by using WRITE_ONCE
- avoid checking stop_queue a second time by moving the doorbell check
- netif_stop_queue() uses atomic operation set_bit() that includes a
full memory barrier on some platforms, therefore use
smp_mb__after_atomic to avoid overhead
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/80085451-3eaf-507a-c7c0-08d607c46fbc@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We can simplify the for() condition and eliminate variable tx_left.
The change also considers that tp->cur_tx may be incremented by a
racing rtl8169_start_xmit().
In addition replace the write to tp->dirty_tx and the following
smp_mb() with an equivalent call to smp_store_mb(). This implicitly
adds a WRITE_ONCE() to the write.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/c2e19e5e-3d3f-d663-af32-13c3374f5def@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
RTL8125B has same or similar short packet hw padding bug as RTL8168evl.
The main workaround has been extended accordingly, however we have to
disable also hw checksumming for short packets on affected new chip
versions. Instead of checking for an affected chip version let's
simply disable hw checksumming for short packets in general.
v2:
- remove the version checks and disable short packet hw csum in general
- reflect this in commit title and message
Fixes: 0439297be9 ("r8169: add support for RTL8125B")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/7fbb35f0-e244-ef65-aa55-3872d7d38698@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The caller of rtl8169_tso_csum_v2() frees the skb if false is returned.
eth_skb_pad() internally frees the skb on error what would result in a
double free. Therefore use __skb_put_padto() directly and instruct it
to not free the skb on error.
Fixes: b423e9ae49 ("r8169: fix offloaded tx checksum for small packets.")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/f7e68191-acff-9ded-4263-c016428a8762@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
tp->dirty_tx isn't changed outside rtl_tx(). Therefore I see no need
to guarantee a specific order of reading tp->dirty_tx and tp->cur_tx.
Having said that we can remove the memory barrier.
In addition use READ_ONCE() when reading tp->cur_tx because it can
change in parallel to rtl_tx().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/2264563a-fa9e-11b0-2c42-31bc6b8e2790@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After switching to the net core rx/tx byte/packet counters we can
remove the now unused private version.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Switch to the net core rx/tx byte/packet counter infrastructure.
This simplifies the code, only small drawback is some memory overhead
because we use just one queue, but allocate the counters per cpu.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
For several network drivers it was reported that using
__napi_schedule_irqoff() is unsafe with forced threading. One way to
fix this is switching back to __napi_schedule, but then we lose the
benefit of the irqoff version in general. As stated by Eric it doesn't
make sense to make the minimal hard irq handlers in drivers using NAPI
a thread. Therefore ensure that the hard irq handler is never
thread-ified.
Fixes: 9a899a35b0 ("r8169: switch to napi_schedule_irqoff")
Link: https://lkml.org/lkml/2020/10/18/19
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/4d3ef84a-c812-5072-918a-22a6f6468310@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Factor out handling the private packet/byte counters to new
functions rtl_get_priv_stats() and rtl_inc_priv_stats().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Small conflict around locking in rxrpc_process_event() -
channel_lock moved to bundle in next, while state lock
needs _bh() from net.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some firmware files trigger a PHY soft reset and don't wait for it to
be finished. PHY register writes directly after applying the firmware
may fail or provide unexpected results therefore. Fix this by waiting
for bit BMCR_RESET to be cleared after applying firmware.
There's nothing wrong with the referenced change, it's just that the
fix will apply cleanly only after this change.
Fixes: 89fbd26cca ("r8169: fix firmware not resetting tp->ocp_base")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Rejecting non-native endian BTF overlapped with the addition
of support for it.
The rest were more simple overlapping changes, except the
renesas ravb binding update, which had to follow a file
move as well as a YAML conversion.
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr reported that after resume from suspend RTL8402 partially
truncates incoming packets, and re-initializing register RxConfig
before the actual chip re-initialization sequence is needed to avoid
the issue.
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Proposed-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Petr reported that system freezes on r8169 driver load on a system
using ether_clk. The original change was done under the assumption
that the clock isn't needed for basic operations like chip register
access. But obviously that was wrong.
Therefore effectively revert the original change, and in addition
leave the clock active when suspending and WoL is enabled. Chip may
not be able to process incoming packets otherwise.
Fixes: 9f0b54cd16 ("r8169: move switching optional clock on/off to pll power functions")
Reported-by: Petr Tesarik <ptesarik@suse.cz>
Tested-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Mistakenly bit 2 was set instead of bit 3 as in the vendor driver.
Fixes: a7a92cf815 ("r8169: sync PCIe PHY init with vendor driver 8.047.01")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We got slightly different patches removing a double word
in a comment in net/ipv4/raw.c - picked the version from net.
Simple conflict in drivers/net/ethernet/ibm/ibmvnic.c. Use cached
values instead of VNIC login response buffer (following what
commit 507ebe6444 ("ibmvnic: Fix use-after-free of VNIC login
response buffer") did).
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
After making use of the gro_flush_timeout attribute I once got a
tx timeout due to an interrupt that wasn't handled. Seems using
irq_enabled can be racy, and it's not needed any longer anyway,
so remove it. I've never seen a report about such a race before,
therefore treat the change as an improvement.
There's just one small drawback: If a legacy PCI interrupt is used,
and if this interrupt is shared with a device with high interrupt
rate, then we may handle interrupts even if NAPI disabled them,
and we may see a certain performance decrease under high network load.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Consider the return value of napi_complete_done(), this allows users to
use the gro_flush_timeout sysfs attribute as an alternative to classic
interrupt coalescing.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most chip versions this has been added already. Allow also for
RTL8125A to enable ASPM.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for RTL8125B rev.b. In my tests 2.5Gbps worked well
w/o firmware, however for a stable link at 1Gbps firmware revision
0.0.2 is needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently have two managed helpers for mdiobus - devm_mdiobus_alloc()
and devm_mdiobus_register(). The idea behind devres is that the release
callback releases whatever resource the devm function allocates. In the
mdiobus case however there's no devres associated with the device by
devm_mdiobus_register(). Instead the release callback for
devm_mdiobus_alloc(): _devm_mdiobus_free() unregisters the device if
it is marked as managed.
This all seems wrong. The managed structure shouldn't need to know or
care about whether it's managed or not - and this is the case now for
struct mii_bus. The devres wrapper should be opaque to the managed
resource.
This changeset makes devm_mdiobus_alloc() and devm_mdiobus_register()
conform to common devres standards: devm_mdiobus_alloc() allocates a
devres structure and registers a callback that will call mdiobus_free().
__devm_mdiobus_register() allocated another devres and registers a
callback that will unregister the bus.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
