Setting the tuner frequency at the same time as initializing the other devices
on the i2c bus can cause problems on devices that require firmware download or
extensive calibration proceduces during initialization.
This change allows us to prevent the tune at startup for devices that perform
better without it.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_mr97310a: Change blue gain setting for Sakar Digital VGA camera
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When "shooting" certain (quite rare) scenes, the mr97310's compression is not
effective and it cannot keep up with the data stream. This patch adds a
minimum clock divider control, which influences the maximum framerate,
libv4l will automatically increase this minimum clockdiv control when it
detect the cam cannot keep up.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The variables are unsigned so the test `>= 0' is always true,
the `< 0' test always fails. In these cases the other part of
the test catches wrapped values.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
In buffer_release() the previously allocated pagetables are not
freed, which might result in a memory leak in certain application
use-cases, where the frame format is changed from planar format to
non-planar format. The fix explicitely frees the page tables when a
format change is done and when buffer_release() is called.
Signed-off-by: Johann Friedrichs <johann.friedrichs@web.de>
Signed-off-by: Michael Hunold <hunold@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Upcoming I2C v4l2_subdev drivers need a way to control the subdevice
power state from the core. This use case is already partially covered by
the tuner s_standby operation, but no way to explicitly come back from
the standby state is available.
Rename the tuner s_standby operation to core s_power, and fix tuner
drivers accordingly. The tuner core will call s_power(0) instead of
s_standby(). No explicit call to s_power(1) is required for tuners as
they are supposed to wake up from standby automatically.
[mchehab@redhat.com: CodingStyle fix]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
I do not think it makes sense any longer for ir-kbd-i2c to reject
devices at unknown I2C addresses. The caller can provide all the
details about how the device should be handled. Having to add new
addresses to ir-kbd-i2c so that they aren't rejected is a pain we
don't need. Unsupported devices will be spotted a few lines later
anyway.
This already lets us unlist 2 addresses (0x7a and 0x2d) for which
handling details are always provided by the caller (saa7134-input).
Hopefully we can remove more in the future.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Google is pretty clear that the HVR 1110 IR chip is always at address
0x71 and the BeholdTV IR chip is always at address 0x2d. This
completes the list of IR device addresses for the SAA7134-based
adapters, and we no longer need to probe any of them.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The i2c core prevents us from probing I2C address 0x7a because it's
not a valid 7-bit address (reserved for 10-bit addressing.) So we must
stop probing this address, and explicitly list all adapters which use
it. Under the assumption that only the Upmost Purple TV adapter uses
this invalid address, this fix should do the trick.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: hermann pitton <hermann-pitton@arcor.de>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Recent fixes to the em28xx and saa7134 drivers have been overzealous.
While the ir-kbd-i2c platform data indeed needs to be persistent, the
struct i2c_board_info doesn't, as it is only used by i2c_new_device().
So revert a part of the original fixes, to save some memory.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
cx25840:
Disable 6.5MHz carrier autodetection for PAL, always assume its DK.
Only try to autodetect 6.5MHz carrier for SECAM if user accepts both
system DK and L.
Signed-off-by: Aleksandr V. Piskunov <alexandr.v.piskunov@gmail.com>
Reviewed-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Change own implementation of pwc_atoi() by simple_strtol(x, NULL, 10).
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After detecting failure due to module initialization error, get out.
Don't report jammed hardware. Problem due to a missing break statement.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver also contains a piece of configuration data that produces a
one line description of the specific hardware being driver
(e.g. "Hauppauge 24xxx", "OnAir", etc). This change generates an
informational message to the kernel log reporting the hardware type
being driven. This is a very useful thing to know when diagnosing
problems.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It used to be that the only real detectable reason for the driver to
fail during initialization would be that if the hardware is simply
jammed. However with the advent of the sub-device mechanism in V4L it
is possible now to detect if a sub-device module fails to load
successfully. The pvrusb2 driver does in fact react to this by also
(correctly) failing, however the original diagnostic message "hardware
is jammed" was still being reported. This misleads the user because
in fact it might not actually be a hardware failure. This change adds
logic to tell the difference and then report a more appropriate
message to the kernel log.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Encoder failures are mostly recoverable by the driver. While
it would sure be nice not to have the failure happen in the first
place, this has been going on for years and I doubt that a real
solution will ever present itself. I think that part's firmware is
just slightly flakey and we have to deal with it. The driver does
deal with it just fine, but the warning message going into the kernel
log is probably a little more alarming than it should be. So try to
soften up the warning somewhat.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
pvrusb2: Associate V4L device node in sysfs with the underlying USB
device. This opens the door to device information tracking in udev
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
consolidate common code used to determine if calibration on startup is needed
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If rf_cal_on_startup is enabled in the structure passed into
tda18271_attach, and the cal module option isn't disabled, then we
should run the initialization and calibration procedures during the
tda18271_attach function call, regardless of how many instances of the
driver have been attached. If the device is already calibrated, the
driver will detect that and will only calibrate again if necessary.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If rf_cal_on_startup is enabled in the structure passed into
tda18271_set_config, and the cal module option isn't disabled,
then we should run the initialization and calibration procedures
during the tda18271_set_config function call.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add the set_config method to allow drivers to configure the
tda18271 driver options after attach.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There is already an option for sending 16 byte chunks rather that writing
39 bytes all at once during the tuner's initialization. Some i2c buses
can't send 16 bytes at once, so create an option for sending 8 byte chunks.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Thanks to Terry Wu for finding the GPIOs required for svideo / composite input
Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable the standby mode optimization to disable the tda18271
slave tuner output / loop thru options when in low power mode
on the slave tuner, only. The master tuner must always leave
slave tuner output / loop thru enabled.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
- add flip/mirror support for OV2640
- fix for backlight value range
- fix for red-blue inversion hue mode with V4L1 applications
Signed-off-by: Olivier Lorin <o.lorin@laposte.net>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The original implementation of pac_find_sof() does not always find
the Start Of Frame (SOF) marker. Replace it with a state machine
based design.
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marton Nemeth <nm127@freemail.hu>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Xc5000 tuning attempts shouldn't return zero in the case where the firmware
did not load successfully.
Thanks to Michael Krufky for pointing out this issue.
Cc: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for saturation/hue controls, prompted by errors showing up in
the mythbackend log.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca: Don't resubmit error status URB's when suspending
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The gscpa core was not resubmitting URB's when the URB status was an error,
this means we will loose URB's (potentially all stopping the stream) in
case of sporadic USB issues. I've seen this with an Aiptek stv0680 based
PenCam connected through an USB 2.0 hub.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
