Instead of artificially enlarging the command decoding arrays to
P_MAX_CMD entries, check if an index is within the valid range using the
ARRAY_SIZE() macro.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Opening a device only succeeds on a primary node, or when explicitly
setting the allow_oos module parameter to allow opening the device
read-only on a secondary node. There is no other way that a request can
get into drbd_make_request(), so this code cannot trigger.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The previous algorithm for dealing with overlapping concurrent writes
was generating unnecessary warnings for scenarios which could be
legitimate, and did not always handle partially overlapping requests
correctly. Improve it algorithm as follows:
* While local or remote write requests are in progress, conflicting new
local write requests will be delayed (commit 82172f7).
* When a conflict between a local and remote write request is detected,
the node with the discard flag decides how to resolve the conflict: It
will ask its peer to discard conflicting requests which are fully
contained in the local request and retry requests which overlap only
partially. This involves a protocol change.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When the node with the discard flag resolves write conflicts in
dual-primary mode, it may determine that its peer has sent ack packets
on the metadata socket which did not arrive, yet. Wait for the next ack
with ping-timeout instead of a hard-coded 30 seconds.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Commit 9b1e63e changed the concurrent write detection algorithm to only insert
peer requests into write_requests tree after determining that there is no
conflict. With this change, new conflicting local requests could be added
while the algorithm runs, but this case was not handled correctly. Instead of
making the algorithm deal with this case, switch back to adding peer requests
to the write_requests tree immediately: this improves fairness.
When a peer request is discarded, remove that request from the write_requests
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Summary log messages meant for global bitmap IO
should not be printed for bitmap IO caused by
activity log transactions.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Use a new on-disk transaction format for the activity log, which allows
for multiple changes to the active set per transaction.
Using 4k transaction blocks, we can now get rid of the work-around code
to deal with devices not supporting 512 byte logical block size.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Allow multiple changes to the active set of elements in lru_cache.
The only current user of lru_cache, drbd, is driving this generalisation.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We are about to allow several changes to the active set in one activity
log transaction. We have to write out the corresponding bitmap pages as
well, if changed.
Introduce drbd_bm_mark_for_writeout(), then re-use the existing bitmap
writeout path to submit all marked pages in one go.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Some open-coded clear_bit(); smp_mb__after_clear_bit();
should in fact have been smp_mb__before_clear_bit(); clear_bit();
Instead, use clear_bit_unlock() to annotate the intention,
and have it do the right thing.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
As using an empty activity log is the whole point of the excercise,
make sure it is still empty when setting AL_SUSPENDED.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
fold
if (x >= (N+1))
return 0;
if (x < N)
return 0;
into
if (x != N)
return 0;
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Add a macro and helper function for doing that.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
That is used for graceful disconnect only
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In compatibility mode with old DRBDs, use that as the state_mutex
as well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The lock they constructed is only taken when the state_mutex
was already taken. It is superficial.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
And removed the unused mdev parameter, and made the order of
the state parameters: os, ns
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
No longer work callbacks must operate on a mdev. From now on they
can also operate on a tconn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The drbd_md_sync(mdev) happens in the after state change anyways...
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
