Avoid touching the flip setup regs while
acceleration is running. Set them at modeset
rather than during pageflip. Touching these
regs while acceleration is active caused hangs
on pre-avivo chips. These chips do not seem
to be affected, but better safe than sorry,
plus it avoids repeatedly reprogramming the
regs every flip.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Typo in the aspect scale setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'intel/drm-intel-next' of ../drm-next: (755 commits)
drm/i915: Only wait on a pending flip if we intend to write to the buffer
drm/i915/dp: Sanity check eDP existence
drm/i915: Rebind the buffer if its alignment constraints changes with tiling
drm/i915: Disable GPU semaphores by default
drm/i915: Do not overflow the MMADDR write FIFO
Revert "drm/i915: fix corruptions on i8xx due to relaxed fencing"
drm/i915: Don't save/restore hardware status page address register
drm/i915: don't store the reg value for HWS_PGA
drm/i915: fix memory corruption with GM965 and >4GB RAM
Linux 2.6.38-rc7
Revert "TPM: Long default timeout fix"
drm/i915: Re-enable GPU semaphores for SandyBridge mobile
drm/i915: Replace vblank PM QoS with "Interrupt-Based AGPBUSY#"
Revert "drm/i915: Use PM QoS to prevent C-State starvation of gen3 GPU"
drm/i915: Allow relocation deltas outside of target bo
drm/i915: Silence an innocuous compiler warning for an unused variable
fs/block_dev.c: fix new kernel-doc warning
ACPI: Fix build for CONFIG_NET unset
mm: <asm-generic/pgtable.h> must include <linux/mm_types.h>
x86: Use u32 instead of long to set reset vector back to 0
...
Conflicts:
drivers/gpu/drm/i915/i915_gem.c
... and switch it to container_of upcasting.
v2: converted new pageflip code-paths.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The fixed ref/post dividers are set by the AdjustPll table
rather than the ss info table on dce4+. Make sure we enable
the fractional feedback dividers when using a fixed post
or ref divider on them as well.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=29272
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
The problematic boards have a recommended reference divider
to be used when spread spectrum is enabled on the laptop panel.
Enable the use of the recommended reference divider along with
the new pll algo.
v2: testing options
v3: When using the fixed reference divider with LVDS, prefer
min m to max p and use fractional feedback dividers.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28852https://bugzilla.kernel.org/show_bug.cgi?id=24462https://bugzilla.kernel.org/show_bug.cgi?id=26552
MacbookPro issues reported by Justin Mattock <justinmattock@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
- set scaler table clears the interleave bit, need to
reset it in encoder quirks, this was already done for
pre-dce4.
- remove the interleave settings from set_base() functions
this is now handled in the encoder quirks functions, and
isn't technically part of the display base setup.
- rename evergreen_do_set_base() to dce4_do_set_base() since
it's used on both evergreen and NI asics.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=28182
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Based on the vbios code. This should hopefully
fix the pll problems on a number of avivo asics
once it's enabled.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
R6xx+ have per-block swappers. BE content in the
framebuffer will now be swapped properly during scanout.
Untested, however, the same code is reported working in
the UMS ddx.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
On resume, we were attemping to unblank the displays before the
timing and plls had be reprogrammed which led to atom timeouts
waiting for things that are not yet programmed. Re-program
the mode first, then reset the dpms state.
This fixes the infamous atombios timeouts on resume.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Seems to cause problems on certain laptops
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=24462
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Tested-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The enter argument as implemented by commit 413d45d362 (drm, kdb, kms:
Add an enter argument to mode_set_base_atomic() API) should be more
descriptive as to what it does vs just passing 1 and 0 around.
There is no runtime behavior change as a result of this patch.
Reported-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-radeon-next' of ../drm-radeon-next:
drm/radeon/kms: add drm blit support for evergreen
drm/radeon: Modify radeon_pm_in_vbl to use radeon_get_crtc_scanoutpos()
drm/radeon: Add function for display scanout position query.
drm/radeon/kms: rework spread spectrum handling
drm/radeon/kms: remove new pll algo
drm/radeon/kms: remove some pll algo flags
drm/radeon/kms: prefer high post dividers in legacy pll algo
drm/radeon/kms: properly handle 40 bit MC addresses in the cursor code
drm/radeon: add properties to configure the width of the underscan borders
drm/radeon/kms/r6xx+: use new style fencing (v3)
drm/radeon/kms: enable writeback (v2)
drm/radeon/kms: clean up r6xx/r7xx blit init (v2)
Some devices such as the radeon chips receive information from user
space which needs to be saved when executing an atomic mode set
operation, else the user space would have to be queried again for the
information.
This patch extends the mode_set_base_atomic() call to pass an argument
to indicate if this is an entry or an exit from an atomic kernel mode
set change. Individual drm drivers can properly save and restore
state accordingly.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
CC: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: David Airlie <airlied@linux.ie>
CC: dri-devel@lists.freedesktop.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This patch reworks spread spectrum handling to enable it
properly on lvds and DP/eDP links. It also fixes several
bugs in the old spread spectrum code.
- Use the ss recommended reference divider if available
when calculating the pll
- Use the proper ss command tables on pre-DCE3 asics
- Avoid reading past the end of the ss info tables
- Enable ss on evergreen asics (lvds, dp, tmds)
- Enable ss on DP/eDP links
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The recent changes to the old algo (prefer high post div)
coupled with the range and precision limitations of using
fixed point with the new algo make the new algo less
useful. So drop the new algo. This should work as well
or better than the old new/old combinations and simplifies
the code a lot.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30218
among others.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
These shouldn't be needed with the post div changes
in the last patch.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV620
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=30029
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
digital underscan support regressed tv-out.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29985
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
There has been periodic evidence that LVDS, on at least some
panels, prefers the dividers selected by the legacy pll algo.
This patch forces the use of the legacy pll algo on RV515
LVDS panels. The old behavior (new pll algo) can be selected
by setting the new_pll module parameter to 1.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add options necessary bits for:
- SS on DP
- SS on LVDS
- set clocks right for DP
- deep color on hdmi (needs additional encoder and edid work as well)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This connector attribute allows you to enable or disable underscan
on a digital output to compensate for panels that automatically
overscan (e.g., many HDMI TVs). Valid values for the attribute are:
off - forces underscan off
on - forces underscan on
auto - enables underscan if an HDMI TV is connected, off otherwise
default value is auto.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This migrates a bunch of DRM_DEBUG->DRM_DEBUG_KMS so we can get more modesetting related info without all the other ioctl handling easily.
Also the PM code moves to DRM_DEBUG_DRIVER mostly.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Disables the crts as per dpms and also disables the ppll
associated with the crtc. This should save additional power.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
At least 'make CONFIG_DEBUG_SECTION_MISMATCH=y' causes
drivers/gpu/drm/radeon/atombios_crtc.c: In function 'atombios_crtc_set_pll':
drivers/gpu/drm/radeon/atombios_crtc.c:684: warning: 'pll' may be used uninitialized in this function
which has the looks of a falso positive.
Add a default: case so that gcc rests assured that all possible pll_id's are covered.
Keep the present cases that fall through to the default one for self-documentation.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Reviewed-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This also simplifies the code and enables reclocking with multiple heads
active by tracking whether the power states are single or multi-head
capable.
Eventually, we will want to select a power state based on external
factors (AC/DC state, user selection, etc.).
(v2) Update for evergreen
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* drm-radeon-evergreen-accel:
drm/radeon: fix cypress firmware typo.
drm/radeon/kms/evergreen: add hpd support
drm/radeon/kms/evergreen: implement irq support
drm/radeon/kms/evergreen: setup and enable the CP
drm/radeon/kms/evergreen: implement gfx init
drm/radeon/kms/evergreen: add soft reset function
drm/radeon/kms/evergreen: add gart support
drm/radeon/kms: add support for evergreen power tables
drm/radeon/kms: update atombios.h power tables for evergreen
Some systems have LCD* rather than DFP* device tags in the bios
for eDP connectors; notably the new apple iMac. This fixes
things up so eDP connectors with either tag will work.
v2: fix typo
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Check that atom cmd and data tables are valid
before using them.
(v2)
- fix some whitespace errors noticed by Rafał Miłecki
- check a few more cases
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- no longer needed with the latest new pll algo fixes.
- also don't use lcd pll limits. They don't seem
to work well for all systems. If we have a case where
they are useful, we can set the flag for that case.
fixes fdo bug 27083
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Adjust modeset ordering to fix spread spectrum.
The spread spectrum command table relies on the
crtc routing to already be set in order to work
properly on some asics.
Should fix fdo bug 25741.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
