Pull networking updates from David Miller:
"Another merge window, another set of networking changes. I've heard
rumblings that the lightweight tunnels infrastructure has been voted
networking change of the year. But what do I know?
1) Add conntrack support to openvswitch, from Joe Stringer.
2) Initial support for VRF (Virtual Routing and Forwarding), which
allows the segmentation of routing paths without using multiple
devices. There are some semantic kinks to work out still, but
this is a reasonably strong foundation. From David Ahern.
3) Remove spinlock fro act_bpf fast path, from Alexei Starovoitov.
4) Ignore route nexthops with a link down state in ipv6, just like
ipv4. From Andy Gospodarek.
5) Remove spinlock from fast path of act_gact and act_mirred, from
Eric Dumazet.
6) Document the DSA layer, from Florian Fainelli.
7) Add netconsole support to bcmgenet, systemport, and DSA. Also
from Florian Fainelli.
8) Add Mellanox Switch Driver and core infrastructure, from Jiri
Pirko.
9) Add support for "light weight tunnels", which allow for
encapsulation and decapsulation without bearing the overhead of a
full blown netdevice. From Thomas Graf, Jiri Benc, and a cast of
others.
10) Add Identifier Locator Addressing support for ipv6, from Tom
Herbert.
11) Support fragmented SKBs in iwlwifi, from Johannes Berg.
12) Allow perf PMUs to be accessed from eBPF programs, from Kaixu Xia.
13) Add BQL support to 3c59x driver, from Loganaden Velvindron.
14) Stop using a zero TX queue length to mean that a device shouldn't
have a qdisc attached, use an explicit flag instead. From Phil
Sutter.
15) Use generic geneve netdevice infrastructure in openvswitch, from
Pravin B Shelar.
16) Add infrastructure to avoid re-forwarding a packet in software
that was already forwarded by a hardware switch. From Scott
Feldman.
17) Allow AF_PACKET fanout function to be implemented in a bpf
program, from Willem de Bruijn"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1458 commits)
netfilter: nf_conntrack: make nf_ct_zone_dflt built-in
netfilter: nf_dup{4, 6}: fix build error when nf_conntrack disabled
net: fec: clear receive interrupts before processing a packet
ipv6: fix exthdrs offload registration in out_rt path
xen-netback: add support for multicast control
bgmac: Update fixed_phy_register()
sock, diag: fix panic in sock_diag_put_filterinfo
flow_dissector: Use 'const' where possible.
flow_dissector: Fix function argument ordering dependency
ixgbe: Resolve "initialized field overwritten" warnings
ixgbe: Remove bimodal SR-IOV disabling
ixgbe: Add support for reporting 2.5G link speed
ixgbe: fix bounds checking in ixgbe_setup_tc for 82598
ixgbe: support for ethtool set_rxfh
ixgbe: Avoid needless PHY access on copper phys
ixgbe: cleanup to use cached mask value
ixgbe: Remove second instance of lan_id variable
ixgbe: use kzalloc for allocating one thing
flow: Move __get_hash_from_flowi{4,6} into flow_dissector.c
ixgbe: Remove unused PCI bus types
...
CPSW driver has multiple compatibles for errata implementations but not
documented, add necessary documentation.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
An SFP module may have a link up/down status pin which can be
connection to a GPIO line of the host. Add support for reading such an
GPIO in the fixed_phy driver.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 4.3.
With this one we have:
- A new driver for Samsung's S3FWRN5 NFC chipset. In order to
properly support this driver, a few NCI core routines needed
to be exported. Future drivers like Intel's Fields Peak will
benefit from this.
- SPI support as a physical transport for STM st21nfcb.
- An additional netlink API for sending replies back to userspace
from vendor commands.
- 2 small fixes for TI's trf7970a
- A few st-nci fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=KMsn
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.3 pull request
This is the NFC pull request for 4.3.
With this one we have:
- A new driver for Samsung's S3FWRN5 NFC chipset. In order to
properly support this driver, a few NCI core routines needed
to be exported. Future drivers like Intel's Fields Peak will
benefit from this.
- SPI support as a physical transport for STM st21nfcb.
- An additional netlink API for sending replies back to userspace
from vendor commands.
- 2 small fixes for TI's trf7970a
- A few st-nci fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add driver for Samsung S3FWRN5 NFC controller.
S3FWRN5 is using NCI protocol and I2C communication interface.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With more than two switches in a hierarchy, it becomes necessary to
describe multi-hop routes between switches. The current binding does
not allow this, although the older platform_data did. Extend the link
property to be a list rather than a single phandle to a remote switch.
It is then possible to express that a port should be used to reach
more than one switch and the switch maybe more than one hop away.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using a cluster of switches, some topologies will have an MDIO
bus per switch, not one for the whole cluster. Allow this to be
represented in the device tree, by adding an optional mii-bus property
at the switch level. The old platform_device method of instantiation
supports this already, so only the device tree binding needs extending
with an additional optional phandle.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some of the K2E and K2L platforms, the two DWORDs in
efuse occupied by the pre-programmed mac address for
slave port 1 are swapped. To workaround this issue,
this patch adds a new define NETCP_EFUSE_ADDR_SWAP (2)
which signifies the occurrence of such swapping so that
the driver can take proper action. The flag can be
enabled in the corresponding netcp interface dts binding
as efuse-mac = <2> under the corresponding netcp
interface node.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding documentation for the Synopsys DWC Ethernet
QoS driver supporting revision 4.10a of the hardware IP.
Signed-off-by: Lars Persson <larper@axis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently the PHY management type is selected by the MAC driver arbitrary.
The decision is based on the presence of the "fixed-link" node and on a
will of the driver's authors.
This caused a regression recently, when mvneta driver suddenly started
to use the in-band status for auto-negotiation on fixed links.
It appears the auto-negotiation may not work when expected by the MAC driver.
Sebastien Rannou explains:
<< Yes, I confirm that my HW does not generate an in-band status. AFAIK, it's
a PHY that aggregates 4xSGMIIs to 1xQSGMII ; the MAC side of the PHY (with
inband status) is connected to the switch through QSGMII, and in this context
we are on the media side of the PHY. >>
https://lkml.org/lkml/2015/7/10/206
This patch introduces the new string property 'managed' that allows
the user to set the management type explicitly.
The supported values are:
"auto" - default. Uses either MDIO or nothing, depending on the presence
of the fixed-link node
"in-band-status" - use in-band status
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
CC: Rob Herring <robh+dt@kernel.org>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Kumar Gala <galak@codeaurora.org>
CC: Florian Fainelli <f.fainelli@gmail.com>
CC: Grant Likely <grant.likely@linaro.org>
CC: devicetree@vger.kernel.org
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The mvneta driver supports the Ethernet IP found in the Armada 370, XP,
380 and 385 SoCs. Since at least one more hardware feature is available
for the Armada XP SoCs then a way to identify them is needed.
This patch introduces a new compatible string "marvell,armada-xp-neta".
Signed-off-by: Simon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff18204 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple LAN device for debug or management purposes.
Device supports interrupts for RX and TX(completion).
Device does not have DMA ability.
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Tal Zilcer <talz@ezchip.com>
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add constants and callback functions for the dwmac on rk3368 socs.
As can be seen, the base structure is the same, only registers and
the bits in them moved slightly.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add sama5d2 to the biding documentation for this use of the GEM IP.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sama5d4, we only have a GEM IP that is configured to do 10/100 Mbits. So the
use of "Gigabit" can be confusing.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the driver and the DT bindings we use the "atmel" prefix. Fix it in the
binding documentation.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 4.2.
- NCI drivers can now define their own handlers for processing
proprietary NCI responses and notifications.
- NFC vendors can use a dedicated netlink API to send their own
proprietary commands, like e.g. all commands needed to implement
vendor specific manufacturing tools.
- A new generic NCI over UART driver against which any NCI chipset
running on top of a serial interface can register.
- The st21nfcb driver is renamed to st-nci as it can and will support
most of ST Microelectronics NCI chipsets.
- The st21nfcb driver can put its CLF in hibernate mode and save
significant amount of power.
- A few st21nfcb minor fixes.
- The NXP NCI driver now supports ACPI enumeration.
- The Marvell NCI driver now supports both USB and serial
physical interfaces.
- The Marvell NCI drivers also supports NCI frames being muxed
over HCI. This is a setting that can be defined by a DT property.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=+IG2
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC 4.2 pull request
This is the NFC pull request for 4.2.
- NCI drivers can now define their own handlers for processing
proprietary NCI responses and notifications.
- NFC vendors can use a dedicated netlink API to send their own
proprietary commands, like e.g. all commands needed to implement
vendor specific manufacturing tools.
- A new generic NCI over UART driver against which any NCI chipset
running on top of a serial interface can register.
- The st21nfcb driver is renamed to st-nci as it can and will support
most of ST Microelectronics NCI chipsets.
- The st21nfcb driver can put its CLF in hibernate mode and save
significant amount of power.
- A few st21nfcb minor fixes.
- The NXP NCI driver now supports ACPI enumeration.
- The Marvell NCI driver now supports both USB and serial
physical interfaces.
- The Marvell NCI drivers also supports NCI frames being muxed
over HCI. This is a setting that can be defined by a DT property.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support of Marvell NFC chip controlled over UART
Signed-off-by: Vincent Cuissard <cuissard@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Ethernet AVB includes an Gigabit Ethernet controller (E-MAC) that is basically
compatible with SuperH Gigabit Ethernet E-MAC. Ethernet AVB has a dedicated
direct memory access controller (AVB-DMAC) that is a new design compared to the
SuperH E-DMAC. The AVB-DMAC is compliant with 3 standards formulated for IEEE
802.1BA: IEEE 802.1AS timing and synchronization protocol, IEEE 802.1Qav real-
time transfer, and the IEEE 802.1Qat stream reservation protocol.
The driver only supports device tree probing, so the binding document is
included in this patch.
Based on the original patches by Mitsuhiro Kimura.
Signed-off-by: Mitsuhiro Kimura <mitsuhiro.kimura.kc@renesas.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STMicroelectronics NFC NCI chips family is extending
with the new ST21NFCC using the AMS AS39230 RF booster.
The st21nfcb driver is relevant for this solution and
might be with future products.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Fix the device tree entries to modify the '_' to '-'.
Also changes the names of the internal delay properties
from -int- to -internal- as the -int- appeared as a keyword.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current versions of the trf7970a has an erratum where it returns
an extra byte in the response to 'Read Multiple Block' (RMB) commands.
This command is issued to Type 5 tags (i.e., ISO/IEC 15693 tags) by
the neard daemon.
To handle this, define a new Device Tree property,
't5t-rmb-extra-byte-quirk', which indicates that the associated
trf7970a device has this erratum. The trf7970a device driver
will then ensure that the response length to RMB commands is
reduced by one byte (for devices with the erratum).
Signed-off-by: Mark A. Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add support for the TI dp83867 Gigabit ethernet phy
device.
The DP83867 is a robust, low power, fully featured
Physical Layer transceiver with integrated PMD
sublayers to support 10BASE-T, 100BASE-TX and
1000BASE-T Ethernet protocols.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the device tree bindings documentation for the QCA IPQ806x
variant of the Synopsys DesignWare MAC.
Signed-off-by: Mathieu Olivari <mathieu@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
drivers/net/phy/phy.c
include/linux/skbuff.h
net/ipv4/tcp.c
net/switchdev/switchdev.c
Switchdev was a case of RTNH_H_{EXTERNAL --> OFFLOAD}
renaming overlapping with net-next changes of various
sorts.
phy.c was a case of two changes, one adding a local
variable to a function whilst the second was removing
one.
tcp.c overlapped a deadlock fix with the addition of new tcp_info
statistic values.
macb.c involved the addition of two zyncq device entries.
skbuff.h involved adding back ipv4_daddr to nf_bridge_info
whilst net-next changes put two other existing members of
that struct into a union.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the device tree support of the amd-xgbe driver by defining
the PHY-related resources within the ethernet device node. The support
provides backwards compatibility with the original way.
Update the driver version to 1.0.2.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMD XGBE device is intended to work with a specific integrated PHY
and that PHY is not meant to be a standalone PHY for use by other
devices. As such this patch removes the phylib driver and implements
the PHY support in the amd-xgbe driver (the majority of the logic from
the phylib driver is moved into the amd-xgbe driver).
Update the driver version to 1.0.1.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding documentation for nxp,lpc1850-dwmac.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet PHY devices/switches may not properly release the MDIO bus
during turn-around time, and fail to drive it low, which can be seen by
some controllers as a read failure, while the data clocked in is still
correct.
Add a boolean property "broken-turn-around" which is parsed by the
generic MDIO bus probing code and will set the corresponding bit in the
MDIO bus phy_ignore_ta_mask bitmask for MDIO bus drivers to utilize that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add "cdns,zynqmp-gem" to be used for Zynq Ultrascale+ MPSoC.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As always, this tends to be one of our bigger branches. There are lots of
updates this release, but not that many jumps out as something that needs
more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- More graphics DT pieces falling into place on Exynos, bridges, clocks.
- Plenty of DT updates for Qualcomm platforms for various IP blocks
- Some churn on Tegra due to switch-over to tool-generated pinctrl data
- Misc fixes and updates for Atmel at91 platforms
- Various DT updates to add IP block support on Broadcom's Cygnus platforms
- More updates for Renesas platforms as DT support is added for various IP
blocks (IPMMU, display, audio, etc).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=wqhB
-----END PGP SIGNATURE-----
Merge tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM DT updates from Olof Johansson:
"As always, this tends to be one of our bigger branches. There are
lots of updates this release, but not that many jumps out as something
that needs more detailed coverage. Some of the highlights are:
- DTs for the new Annapurna Labs Alpine platform
- more graphics DT pieces falling into place on Exynos, bridges,
clocks.
- plenty of DT updates for Qualcomm platforms for various IP blocks
- some churn on Tegra due to switch-over to tool-generated pinctrl
data
- misc fixes and updates for Atmel at91 platforms
- various DT updates to add IP block support on Broadcom's Cygnus
platforms
- more updates for Renesas platforms as DT support is added for
various IP blocks (IPMMU, display, audio, etc)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (231 commits)
ARM: dts: alpine: add internal pci
Revert "ARM: dts: mt8135: Add pinctrl/GPIO/EINT node for mt8135."
ARM: mvebu: use 0xf1000000 as internal registers on Armada 370 DB
ARM: dts: qcom: Add idle state device nodes for 8064
ARM: dts: qcom: Add idle states device nodes for 8084
ARM: dts: qcom: Add idle states device nodes for 8974/8074
ARM: dts: qcom: Update power-controller device node for 8064 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8084 Krait CPUs
ARM: dts: qcom: Add power-controller device node for 8074 Krait CPUs
devicetree: bindings: Document qcom,idle-states
devicetree: bindings: Update qcom,saw2 node bindings
dt-bindings: Add #defines for MSM8916 clocks and resets
arm: dts: qcom: Add LPASS Audio HW to IPQ8064 device tree
arm: dts: qcom: Add APQ8084 chipset SPMI PMIC's nodes
arm: dts: qcom: Add 8x74 chipset SPMI PMIC's nodes
arm: dts: qcom: Add SPMI PMIC Arbiter nodes for APQ8084 and MSM8974
arm: dts: qcom: Add LCC nodes
arm: dts: qcom: Add TCSR support for MSM8960
arm: dts: qcom: Add TCSR support for MSM8660
arm: dts: qcom: Add TCSR support for IPQ8064
...
devicetree changes queued up for v4.1. Here are the highlights:
- Lots of unittest cleanup from Frank Rowand
- Bugfixes and updates to the of_graph code
- Tighten up of_get_mac_address() code
- Documentation updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=u6Zy
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux
Pull devicetree changes from Grant Likely:
"Here are the devicetree changes queued up for v4.1. Nothing really
exciting here. Rob has another few commits for big-endian attached
UARTs, but those will be sent in a separate merge request since they
haven't been as thoroughly tested as this batch.
Here are the highlights:
- lots of unittest cleanup from Frank Rowand
- bugfixes and updates to the of_graph code
- tighten up of_get_mac_address() code
- documentation updates"
* tag 'devicetree-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/glikely/linux:
of/unittest: Fix of_platform_depopulate test case
of/unittest: early return from test skips tests
of/unittest: breadcrumbs to reduce pain of future maintainers
of/unittest: reduce checkpatch noise - line after declarations
of/unittest: typo in error string
of/unittest: add const where needed
of_net: factor out repetitive code from of_get_mac_address()
drivers/of: Add empty ranges quirk for PA-Semi
of: Allow selection of OF_DYNAMIC and OF_OVERLAY if OF_UNITTEST
of: Empty node & property flag accessors when !OF
of: Explicitly include linux/types.h in of_graph.h
dt-bindings: brcm: rationalize Broadcom documentation naming
of/unittest: replace 'selftest' with 'unittest'
Documentation: rename of_selftest.txt to of_unittest.txt
Documentation: update the of_selftest.txt
dt: OF_UNITTEST make dependency broken
MAINTAINERS: Pantelis Antoniou device tree overlay maintainer
of: Add of_graph_get_port_by_id function
of: Add for_each_endpoint_of_node helper macro
of: Decrement refcount of previous endpoint in of_graph_get_next_endpoint
The Synopsys stmmac fifo sizes are configurable, and need to be known
in order to configure certain controller features. This patch adds
tx-fifo-depth and rx-fifo-depth properties to the stmmac document
file.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the NFC pull request for 4.1.
This is a shorter one than usual, as the Intel Field Peak NFC
driver could not make it in time.
We have:
- A new driver for NXP NCI based chipsets, like e.g. the NPC100 or
the PN7150. It currently only supports an i2c physical layer, but
could easily be extended to work on top of e.g. SPI.
This driver also includes support for user space triggered firmware
updates.
- A few minor st21nfc[ab] fixes, cleanups, and comments improvements.
- A pn533 error return fix.
- A few NFC related logs formatting cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MzOJ
-----END PGP SIGNATURE-----
Merge tag 'nfc-next-4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-next
Samuel Ortiz says:
====================
NFC: 4.1 pull request
This is the NFC pull request for 4.1.
This is a shorter one than usual, as the Intel Field Peak NFC
driver could not make it in time.
We have:
- A new driver for NXP NCI based chipsets, like e.g. the NPC100 or
the PN7150. It currently only supports an i2c physical layer, but
could easily be extended to work on top of e.g. SPI.
This driver also includes support for user space triggered firmware
updates.
- A few minor st21nfc[ab] fixes, cleanups, and comments improvements.
- A pn533 error return fix.
- A few NFC related logs formatting cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The DWMAC block on certain SoCs (such as IMG Pistachio) have a second
clock which must be enabled in order to access the peripheral's
register interface, so add support for requesting and enabling an
optional "pclk".
Signed-off-by: Andrew Bresticker <abrestic@chromium.org>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/mellanox/mlx4/cmd.c
net/core/fib_rules.c
net/ipv4/fib_frontend.c
The fib_rules.c and fib_frontend.c conflicts were locking adjustments
in 'net' overlapping addition and removal of code in 'net-next'.
The mlx4 conflict was a bug fix in 'net' happening in the same
place a constant was being replaced with a more suitable macro.
Signed-off-by: David S. Miller <davem@davemloft.net>
According to description in 'include/net/dsa.h', in cascade switches
configurations where there are more than one interconnected devices,
'rtable' array in 'dsa_chip_data' structure is used to indicate which
port on this switch should be used to send packets to that are destined
for corresponding switch.
However, dsa_of_setup_routing_table() fills 'rtable' with port numbers
of the _target_ switch, but not current one.
This commit removes redundant devicetree parsing and adds needed port
number as a function argument. So dsa_of_setup_routing_table() now just
looks for target switch number by parsing parent of 'link' device node.
To remove possible misunderstandings with the way of determining target
switch number, a corresponding comment was added to the source code and
to the DSA device tree bindings documentation file.
This was tested on a custom board with two Marvell 88E6095 switches with
following corresponding routing tables: { -1, 10 } and { 8, -1 }.
Signed-off-by: Pavel Nakonechny <pavel.nakonechny@skitlab.ru>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patchset attempts to standardize the naming of dt-bindings
documents based on the Broadcom vendor prefix of brcm.
Although there are no guidelines currently present for how to name
the dt-bindings document the "vendor,binding.txt" style is in use by
some of the other vendors.
Acked-by: Lee Jones <lee@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Gregory Fong <gregory.0xf0@gmail.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Add a module to the NXP-NCI driver to support NFC controllers with an
I2C control interface, such as the NPC100.
Signed-off-by: Clément Perrochaud <clement.perrochaud@effinnov.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add device tree binding documentation for TI's wilink
(wl12xx and wl18xx) wlan chip.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Tested-by: Nikita Kiryanov <nikita@compulab.co.il>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
NetCP 1.5 available on newer K2 SoCs such as K2E and K2L introduced 3
variants of the ethss subsystem, 9 port, 5 port and 2 port. These have
one host port towards the CPU and N external slave ports.
To customize the driver for these new ethss sub systems, multiple
compatibility strings are introduced. Currently some of parameters that
are different on different variants such as number of ALE ports, stats
modules and number of ports are defined through constants. These are now
changed to variables in gbe_priv data that get set based on the
compatibility string. This is required as there are no hardware
identification registers available to distinguish among the variants
of NetCP 1.5 ethss. However there is identification register available
to differentiate between NetCP 1.4 vs NetCP 1.5 and the same is made use
of in the code to differentiate them.
For more reading on the details of this peripheral, please refer to the
User Guide available at http://www.ti.com/lit/pdf/spruhz3
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Ethss has multiple modules within the sub system
- switch sub system
- sgmii
- mdio
- switch module
NetCP driver re-uses existing davinci mdio driver. It requires to
have its own register region to map the reg space. So restructure
the code to use separate reg region for the individual modules it
manages. Use range property to define register space of NetCP and
use reg property to define individual reg spaces. So MDIO will have
its own reg space to map. This is a pre-requisite to enable MDIO
driver for NetCP.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Mugunthan V N <mugunthanvnm@ti.com>
CC: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: Christoph Jaeger <cj@linux.com>
CC: Lokesh Vutla <lokeshvutla@ti.com>
CC: Markus Pargmann <mpa@pengutronix.de>
CC: Kumar Gala <galak@codeaurora.org>
CC: Ian Campbell <ijc+devicetree@hellion.org.uk>
CC: Mark Rutland <mark.rutland@arm.com>
CC: Pawel Moll <pawel.moll@arm.com>
CC: Rob Herring <robh+dt@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-03-19
This wont the last 4.1 bluetooth-next pull request, but we've piled up
enough patches in less than a week that I wanted to save you from a
single huge "last-minute" pull somewhere closer to the merge window.
The main changes are:
- Simultaneous LE & BR/EDR discovery support for HW that can do it
- Complete LE OOB pairing support
- More fine-grained mgmt-command access control (normal user can now do
harmless read-only operations).
- Added RF power amplifier support in cc2520 ieee802154 driver
- Some cleanups/fixes in ieee802154 code
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The TI CC2521 is an RF power amplifier that is designed to interface
with the CC2520. Conveniently, it directly interfaces with the CC2520
and does not require any pins to be connected to a
microcontroller/processor. Adding a CC2591 increases the CC2520's range,
which is useful for border router and other wall-powered applications.
Using the CC2591 with the CC2520 requires configuring the CC2520 GPIOs
that are connected to the CC2591 to correctly set the CC2591 into TX and
RX modes. Further, TI recommends that the CC2520_TXPOWER and
CC2520_AGCCTRL1 registers are set differently to maximize the CC2591's
performance. These settings are covered in TI Application Note AN065.
This patch adds an optional `amplified` field to the cc2520 entry in the
device tree. If present, the CC2520 will be configured to operate with a
CC2591.
The expected pin mapping is:
CC2520 GPIO0 --> CC2591 EN
CC2520 GPIO5 --> CC2591 PAEN
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Acked-by: Varka Bhadram <varkabhadram@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Keyur Chudgar <kchudgar@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cadence/macb.c
Overlapping changes in macb driver, mostly fixes and cleanups
in 'net' overlapping with the integration of at91_ether into
macb in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing "cdns,at91sam9260-macb", "atmel,sama5d3-gem" and
"atmel,sama5d4-gem" compatible strings.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
