EtherAVB hardware requires 0 to be written to status register bits in
order to clear them, however, care must be taken not to:
1. Clear other bits, by writing zero to them
2. Write one to reserved bits
This patch corrects the ravb driver with respect to the second point above.
This is done by defining reserved bit masks for the affected registers and,
after auditing the code, ensure all sites that may write a one to a
reserved bit use are suitably masked.
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the following compile warning:
drivers/net/ethernet/broadcom/bnxt/bnxt_devlink.c:49:5: warning: nvm_param.dir_type may be used uninitialized in this function [-Wmaybe-uninitialized]
if (nvm_param.dir_type == BNXT_NVM_PORT_CFG)
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJboCdPAAoJEEg/ir3gV/o+OqQH/2U2kCMUHRuG6WGEbm+bTz7m
fF2L1iRMeXvpmD0FrWs1XiBEg1/6Gf6GfNLmuwRqhHJMi/ok1310V5UbQ3dcXEQ5
7rIzBUbd2jyrI5wln9ISgmvgi/r7Cdzf9xNM3MHmPCouNWxbX85VLTGdTXcsUknd
Z7lZHbPjB8aeZEBmeQdNbGvwZOe9IIgTlfEN4gwrYvUtJD82HrGgGpdLvnSWgy4X
RhKdjvhkYx5ba3AH9CbY88oR5LRjhk3dGhngpMDvQZBmqE0W0j8tXkR8bj36zJN6
m2YJadeGlds7fubFORYaaDGuPBtCT5SnrJqboEMZ8fzuJMqdyvBNI/LtTRTIGAc=
=FOdR
-----END PGP SIGNATURE-----
Merge tag 'mlx5-fixes-2018-09-17' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2018-09-17
Sorry about the previous submission of this series which was mistakenly
marked for net-next, here I am resending with 'net' mark.
This series provides three fixes to mlx5 core and mlx5e netdevice
driver.
Please pull and let me know if there's any problem.
For -stable v4.16:
('net/mlx5: Check for SQ and not RQ state when modifying hairpin SQ')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
On the Netgear WNDAP620, the emac ethernet isn't receiving nor
xmitting any frames from/to the RTL8363SB (identifies itself
as a RTL8367RB).
This is caused by the emac hardware not knowing the forced link
parameters for speed, duplex, pause, etc.
This begs the question, how this was working on the original
driver code, when it was necessary to set the phy_address and
phy_map to 0xffffffff. But I guess without access to the old
PPC405/440/460 hardware, it's not possible to know.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to ETSI TS 102 622 specification chapter 4.4 pipe identifier
is 7 bits long which allows for 128 unique pipe IDs. Because
NFC_HCI_MAX_PIPES is used as the number of pipes supported and not
as the max pipe ID, its value should be 128 instead of 127.
nfc_hci_recv_from_llc extracts pipe ID from packet header using
NFC_HCI_FRAGMENT(0x7F) mask which allows for pipe ID value of 127.
Same happens when NCI_HCP_MSG_GET_PIPE() is being used. With
pipes array having only 127 elements and pipe ID of 127 the OOB memory
access will result.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Allen Pais <allen.pais@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling SHDLC I-Frame commands "pipe" field used for indexing
into an array should be checked before usage. If left unchecked it
might access memory outside of the array of size NFC_HCI_MAX_PIPES(127).
Malformed NFC HCI frames could be injected by a malicious NFC device
communicating with the device being attacked (remote attack vector),
or even by an attacker with physical access to the I2C bus such that
they could influence the data transfers on that bus (local attack vector).
skb->data is controlled by the attacker and has only been sanitized in
the most trivial ways (CRC check), therefore we can consider the
create_info struct and all of its members to tainted. 'create_info->pipe'
with max value of 255 (uint8) is used to take an offset of the
hdev->pipes array of 127 elements which can lead to OOB write.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Allen Pais <allen.pais@oracle.com>
Cc: "David S. Miller" <davem@davemloft.net>
Suggested-by: Kevin Deus <kdeus@google.com>
Signed-off-by: Suren Baghdasaryan <surenb@google.com>
Acked-by: Kees Cook <keescook@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cleanup function uses "$CMD 2 > /dev/null", which doesn't actually
send stderr to /dev/null, so when the netns doesn't exist, the error
message is shown. Use "2> /dev/null" instead, so that those messages
disappear, as was intended.
Fixes: d1f1b9cbf3 ("selftests: net: Introduce first PMTU test")
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Stefano Brivio <sbrivio@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jose Abreu says:
====================
net: stmmac: Coalesce and tail addr fixes
The fix for coalesce timer and a fix in tail address setting that impacts
XGMAC2 operation.
The series is:
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
on a113 s400 board (single queue)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we are always setting the tail address of descriptor list to
the end of the pre-allocated list.
According to databook this is not correct. Tail address should point to
the last available descriptor + 1, which means we have to update the
tail address everytime we call the xmit function.
This should make no impact in older versions of MAC but in newer
versions there are some DMA features which allows the IP to fetch
descriptors in advance and in a non sequential order so its critical
that we set the tail address correctly.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: f748be531d ("stmmac: support new GMAC4")
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This follows David Miller advice and tries to fix coalesce timer in
multi-queue scenarios.
We are now using per-queue coalesce values and per-queue TX timer.
Coalesce timer default values was changed to 1ms and the coalesce frames
to 25.
Tested in B2B setup between XGMAC2 and GMAC5.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Fixes: ce736788e8 ("net: stmmac: adding multiple buffers for TX")
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gpio base for GPP-E was set incorrectly to 258 instead of 256,
preventing the touchpad working on my Tong Fang GK5CN5Z laptop.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=200787
Signed-off-by: Simon Detheridge <s@sd.ai>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These values are inclusive, so a range of 1 requires min == max.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Martin Kepplinger <martin.kepplinger@ginzinger.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adding 2 new touchpad IDs to support middle button support.
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The CapsLock key on Atari keyboards is not a toggle, it does send the
normal make and break scancodes.
Drop the CapsLock toggle handling code, which did cause the CapsLock
key to merely act as a Shift key.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix errors in Atari keymap (mostly in keypad, help and undo keys).
Patch provided on debian-68k ML by Andreas Schwab <schwab@linux-m68k.org>,
keymap array size and unhandled scancode limit adjusted to 0x73 by me.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Michael Schmitz <schmitzmic@gmail.com>
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch adds wakeup function support for egalax touch
screen, if "wakeup-source" is added to device tree's egalax
touch screen node, the wakeup function will be enabled, and
egalax touch screen will be able to wakeup system from suspend.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gpio_keys.c now exists in the drivers/input/keyboard/ rather than
drivers/input/.
Signed-off-by: Song Qiang <songqiang.1304521@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
than opt-in.
-----BEGIN PGP SIGNATURE-----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=aLd2
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/efi/efi into efi/urgent
Pull EFI fix from Ard Biesheuvel:
Apply a fix from Scott to make the ARM stub's DTB loader opt-out rather
than opt-in.
The original PCI error recovery functionality was for the powerpc-specific
IBM EEH feature. PCIe subsequently added some similar features, including
AER and DPC, that can be used on any architecture.
We want the generic PCI core error handling support to work with all of
these features. Driver error recovery callbacks should be independent of
which feature the platform provides.
Add the generic PCI core error recovery files to the powerpc EEH
MAINTAINERS entry so the powerpc folks will be copied on changes to the
generic PCI error handling strategy.
Add Sam and Oliver as maintainers for this area.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Acked-by: Sam Bobroff <sbobroff@linux.ibm.com>
In order to determine a sane default cache allocation for a new CAT/CDP
resource group, all resource groups are checked to determine which cache
portions are available to share. At this time all possible CLOSIDs
that can be supported by the resource is checked. This is problematic
if the resource supports more CLOSIDs than another CAT/CDP resource. In
this case, the number of CLOSIDs that could be allocated are fewer than
the number of CLOSIDs that can be supported by the resource.
Limit the check of closids to that what is supported by the system based
on the minimum across all resources.
Fixes: 95f0b77ef ("x86/intel_rdt: Initialize new resource group with sane defaults")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-10-git-send-email-fenghua.yu@intel.com
It is possible for a resource group to consist out of MBA as well as
CAT/CDP resources. The "exclusive" resource mode only applies to the
CAT/CDP resources since MBA allocations cannot be specified to overlap
or not. When a user requests a resource group to become "exclusive" then it
can only be successful if there are CAT/CDP resources in the group
and none of their CBMs associated with the group's CLOSID overlaps with
any other resource group.
Fix the "exclusive" mode setting by failing if there isn't any CAT/CDP
resource in the group and ensuring that the CBM checking is only done on
CAT/CDP resources.
Fixes: 49f7b4efa ("x86/intel_rdt: Enable setting of exclusive mode")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-9-git-send-email-fenghua.yu@intel.com
A loop is used to check if a CAT resource's CBM of one CLOSID
overlaps with the CBM of another CLOSID of the same resource. The loop
is run over all CLOSIDs supported by the resource.
The problem with running the loop over all CLOSIDs supported by the
resource is that its number of supported CLOSIDs may be more than the
number of supported CLOSIDs on the system, which is the minimum number of
CLOSIDs supported across all resources.
Fix the loop to only consider the number of system supported CLOSIDs,
not all that are supported by the resource.
Fixes: 49f7b4efa ("x86/intel_rdt: Enable setting of exclusive mode")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-8-git-send-email-fenghua.yu@intel.com
A system supporting pseudo-locking may have MBA as well as CAT
resources of which only the CAT resources could support cache
pseudo-locking. When the schemata to be pseudo-locked is provided it
should be checked that that schemata does not attempt to pseudo-lock a
MBA resource.
Fixes: e0bdfe8e3 ("x86/intel_rdt: Support creation/removal of pseudo-locked region")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-7-git-send-email-fenghua.yu@intel.com
When a new resource group is created, it is initialized with sane
defaults that currently assume the resource being initialized is a CAT
resource. This code path is also followed by a MBA resource that is not
allocated the same as a CAT resource and as a result we encounter the
following unchecked MSR access error:
unchecked MSR access error: WRMSR to 0xd51 (tried to write 0x0000
000000000064) at rIP: 0xffffffffae059994 (native_write_msr+0x4/0x20)
Call Trace:
mba_wrmsr+0x41/0x80
update_domains+0x125/0x130
rdtgroup_mkdir+0x270/0x500
Fix the above by ensuring the initial allocation is only attempted on a
CAT resource.
Fixes: 95f0b77ef ("x86/intel_rdt: Initialize new resource group with sane defaults")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-6-git-send-email-fenghua.yu@intel.com
When multiple resources are managed by RDT, the number of CLOSIDs used
is the minimum of the CLOSIDs supported by each resource. In the function
rdt_bit_usage_show(), the annotated bitmask is created to depict how the
CAT supporting caches are being used. During this annotated bitmask
creation, each resource group is queried for its mode that is used as a
label in the annotated bitmask.
The maximum number of resource groups is currently assumed to be the
number of CLOSIDs supported by the resource for which the information is
being displayed. This is incorrect since the number of active CLOSIDs is
the minimum across all resources.
If information for a cache instance with more CLOSIDs than another is
being generated we thus encounter a warning like:
invalid mode for closid 8
WARNING: CPU: 88 PID: 1791 at [SNIP]/arch/x86/kernel/cpu/intel_rdt_rdtgroup.c
:827 rdt_bit_usage_show+0x221/0x2b0
Fix this by ensuring that only the number of supported CLOSIDs are
considered.
Fixes: e651901187 ("x86/intel_rdt: Introduce "bit_usage" to display cache allocations details")
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-5-git-send-email-fenghua.yu@intel.com
The number of CLOSIDs supported by a system is the minimum number of
CLOSIDs supported by any of its resources. Care should be taken when
iterating over the CLOSIDs of a resource since it may be that the number
of CLOSIDs supported on the system is less than the number of CLOSIDs
supported by the resource.
Introduce a helper function that can be used to query the number of
CLOSIDs that is supported by all resources, irrespective of how many
CLOSIDs are supported by a particular resource.
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-4-git-send-email-fenghua.yu@intel.com
Chen Yu reported a divide-by-zero error when accessing the 'size'
resctrl file when a MBA resource is enabled.
divide error: 0000 [#1] SMP PTI
CPU: 93 PID: 1929 Comm: cat Not tainted 4.19.0-rc2-debug-rdt+ #25
RIP: 0010:rdtgroup_cbm_to_size+0x7e/0xa0
Call Trace:
rdtgroup_size_show+0x11a/0x1d0
seq_read+0xd8/0x3b0
Quoting Chen Yu's report: This is because for MB resource, the
r->cache.cbm_len is zero, thus calculating size in rdtgroup_cbm_to_size()
will trigger the exception.
Fix this issue in the 'size' file by getting correct memory bandwidth value
which is in MBps when MBA software controller is enabled or in percentage
when MBA software controller is disabled.
Fixes: d9b48c86eb ("x86/intel_rdt: Display resource groups' allocations in bytes")
Reported-by: Chen Yu <yu.c.chen@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Chen Yu <yu.c.chen@intel.com>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Xiaochen Shen" <xiaochen.shen@intel.com>
Link: https://lkml.kernel.org/r/20180904174614.26682-1-yu.c.chen@intel.com
Link: https://lkml.kernel.org/r/1537048707-76280-3-git-send-email-fenghua.yu@intel.com
Each resource is associated with a parsing callback to parse the data
provided from user space when writing schemata file.
The 'data' parameter in the callbacks is defined as a void pointer which
is error prone due to lack of type check.
parse_bw() processes the 'data' parameter as a string while its caller
actually passes the parameter as a pointer to struct rdt_cbm_parse_data.
Thus, parse_bw() takes wrong data and causes failure of parsing MBA
throttle value.
To fix the issue, the 'data' parameter in all parsing callbacks is defined
and handled as a pointer to struct rdt_parse_data (renamed from struct
rdt_cbm_parse_data).
Fixes: 7604df6e16 ("x86/intel_rdt: Support flexible data to parsing callbacks")
Fixes: 9ab9aa15c3 ("x86/intel_rdt: Ensure requested schemata respects mode")
Signed-off-by: Xiaochen Shen <xiaochen.shen@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: "H Peter Anvin" <hpa@zytor.com>
Cc: "Tony Luck" <tony.luck@intel.com>
Cc: "Chen Yu" <yu.c.chen@intel.com>
Link: https://lkml.kernel.org/r/1537048707-76280-2-git-send-email-fenghua.yu@intel.com
This adds Intel(R) Trace Hub PCI ID for Ice Lake PCH.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The core of the driver expects the resource array from the glue layer
to be indexed by even numbers, as is the case for 64-bit PCI resources.
This doesn't hold true for others, ACPI in this instance, which leads
to an out-of-bounds access and an ioremap() on whatever address that
access fetches.
This patch fixes the problem by reading resource array differently based
on whether the 64-bit flag is set, which would indicate PCI glue layer.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes: ebc57e399b ("intel_th: Add ACPI glue layer")
CC: stable@vger.kernel.org # v4.17+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a753bfcfdb ("intel_th: Make the switch allocate its subdevices")
brings in new subdevice addition/removal logic that's broken for "host
mode": the SWITCH device has no children to begin with, which is not
handled in the code. This results in a null dereference bug later down
the path.
This patch fixes the subdevice removal code to handle host mode correctly.
Signed-off-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Fixes: a753bfcfdb ("intel_th: Make the switch allocate its subdevices")
CC: stable@vger.kernel.org # v4.14+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vsa.console is indirectly controlled by user-space, hence leading to
a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/tty/vt/vt_ioctl.c:711 vt_ioctl() warn: potential spectre issue
'vc_cons' [r]
Fix this by sanitizing vsa.console before using it to index vc_cons
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kgdb expects poll function to return immediately and
returning NO_POLL_CHAR when no character is available.
Fixes: f5316b4aea ("kgdb,8250,pl011: Return immediately from console poll")
Cc: Jason Wessel <jason.wessel@windriver.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function tty_port_tty_get() gets a reference to the tty. Since
the code is not using tty_port_tty_set(), the reference is kept
even after closing the tty.
Avoid using tty_port_tty_get() by directly access the tty instance.
Since lpuart_start_rx_dma() is called from the .startup() and
.set_termios() callback, it is safe to assume the tty instance is
valid.
Cc: stable@vger.kernel.org # v4.9+
Fixes: 5887ad43ee ("tty: serial: fsl_lpuart: Use cyclic DMA for Rx")
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently, this driver (or the hardware) does not support character
length settings. It's apparently running in 8-bit mode, but it makes
userspace believe it's in 5-bit mode. That makes tcsetattr with CS8
incorrectly fail, breaking e.g. getty from busybox, thus the login shell
on ttyMVx.
Fix by hard-wiring CS8 into c_cflag.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Fixes: 30530791a7 ("serial: mvebu-uart: initial support for Armada-3700 serial port")
Cc: stable <stable@vger.kernel.org> # 4.6+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dependency for the man page rule using asciidoctor incorrectly
specifies a source file in $(OUTPUT). When building out-of-tree, the
source file is not found, resulting in a fall-back to the following rule
which uses xmlto.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20180916151704.GF4765@decadent.org.uk
Fixes: ffef80ecf8 ("perf Documentation: Support for asciidoctor")
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Same problem that got fixed in a similar fashion in tools/perf/ in
c8b5f2c96d ("tools: Introduce str_error_r()"), fix it in the same
way, licensing needs to be sorted out to libbpf to use libapi, so,
for this simple case, just get the same wrapper in tools/lib/bpf.
This makes libbpf and its users (bpftool, selftests, perf) to build
again in Alpine Linux 3.[45678] and edge.
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: Hendrik Brueckner <brueckner@linux.ibm.com>
Cc: Jakub Kicinski <jakub.kicinski@netronome.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Martin KaFai Lau <kafai@fb.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Quentin Monnet <quentin.monnet@netronome.com>
Cc: Thomas Richter <tmricht@linux.ibm.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: Yonghong Song <yhs@fb.com>
Fixes: 1ce6a9fc15 ("bpf: fix build error in libbpf with EXTRA_CFLAGS="-Wp, -D_FORTIFY_SOURCE=2 -O2"")
Link: https://lkml.kernel.org/r/20180917151636.GA21790@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Two fixes for KVM on POWER machines. Both of these relate to memory
corruption and host crashes seen when transparent huge pages are
enabled. The first fixes a host crash that can occur when a DMA
mapping is removed by the guest and the page mapped was part of a
transparent huge page; the second fixes corruption that could occur
when a hypervisor page fault for a radix guest is being serviced at
the same time that the backing page is being collapsed or split.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABCAAGBQJbmFIyAAoJEJ2a6ncsY3Gf+L8H/jRQ0ONUpv2xrgirXdPmfuVv
xIVejn5chiygpo3ZY2YkRGjqMoX8usA5pDQONk9duoc48FedSjjmurfAkSA8NESI
y6DSRGB6pir/reP/7tBVk0eeeMBjbYnHPA7KfI8ijK424VmRpCT5stiUm7gQvSEm
LSRUSLwWKfCCjU78HVtiTuK865WZifrOCy6wiNEl79F1K6T1A+LeGaKrcDLjeK/Q
GsNSbwBK37BOvcsm0W1xrlnCmYtR/nVrhjTFMc5noBuc4znQd3wxitgiInFsOH5V
LUWL6IStFkbGKSxVZuJilkhVF58AAisrJnwvlZsjrExWYf1J42kbyvVoURt0O8I=
=blkZ
-----END PGP SIGNATURE-----
Merge tag 'kvm-ppc-fixes-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc into HEAD
Second set of PPC KVM fixes for 4.19
Two fixes for KVM on POWER machines. Both of these relate to memory
corruption and host crashes seen when transparent huge pages are
enabled. The first fixes a host crash that can occur when a DMA
mapping is removed by the guest and the page mapped was part of a
transparent huge page; the second fixes corruption that could occur
when a hypervisor page fault for a radix guest is being serviced at
the same time that the backing page is being collapsed or split.
- more fallout from the hugetlbfs enablement
- bugfix for vma handling
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=TT85
-----END PGP SIGNATURE-----
Merge tag 'kvm-s390-master-4.19-2' of git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Fixes for 4.19
- more fallout from the hugetlbfs enablement
- bugfix for vma handling
This stops us from doing code patching in init sections after they've
been freed.
In this chain:
kvm_guest_init() ->
kvm_use_magic_page() ->
fault_in_pages_readable() ->
__get_user() ->
__get_user_nocheck() ->
barrier_nospec();
We have a code patching location at barrier_nospec() and
kvm_guest_init() is an init function. This whole chain gets inlined,
so when we free the init section (hence kvm_guest_init()), this code
goes away and hence should no longer be patched.
We seen this as userspace memory corruption when using a memory
checker while doing partition migration testing on powervm (this
starts the code patching post migration via
/sys/kernel/mobility/migration). In theory, it could also happen when
using /sys/kernel/debug/powerpc/barrier_nospec.
Cc: stable@vger.kernel.org # 4.13+
Signed-off-by: Michael Neuling <mikey@neuling.org>
Reviewed-by: Nicholas Piggin <npiggin@gmail.com>
Reviewed-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
- fixes in bus for
- bus lock on master release
- incorrect exit after stream configuration
- duplicate stream state assignment
-----BEGIN PGP SIGNATURE-----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=Imbd
-----END PGP SIGNATURE-----
Merge tag 'soundwire-4.19-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/soundwire into char-misc-linus
Vinod writes:
soundwire fixes for 4.19
- fixes in bus for
- bus lock on master release
- incorrect exit after stream configuration
- duplicate stream state assignment
As documented in spi-mem.h, spi_mem_op->data.buf.{in,out} must be
DMA-able, and commit 4120f8d158 ("mtd: spi-nor: Use the spi_mem_xx()
API") failed to follow this rule as buffers passed to
->{read,write}_reg() are usually placed on the stack.
Fix that by allocating a scratch buffer and copying the data around.
Fixes: 4120f8d158 ("mtd: spi-nor: Use the spi_mem_xx() API")
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Dave writes:
"Various fixes, all over the place:
1) OOB data generation fix in bluetooth, from Matias Karhumaa.
2) BPF BTF boundary calculation fix, from Martin KaFai Lau.
3) Don't bug on excessive frags, to be compatible in situations mixing
older and newer kernels on each end. From Juergen Gross.
4) Scheduling in RCU fix in hv_netvsc, from Stephen Hemminger.
5) Zero keying information in TLS layer before freeing copies
of them, from Sabrina Dubroca.
6) Fix NULL deref in act_sample, from Davide Caratti.
7) Orphan SKB before GRO in veth to prevent crashes with XDP,
from Toshiaki Makita.
8) Fix use after free in ip6_xmit, from Eric Dumazet.
9) Fix VF mac address regression in bnxt_en, from Micahel Chan.
10) Fix MSG_PEEK behavior in TLS layer, from Daniel Borkmann.
11) Programming adjustments to r8169 which fix not being to enter deep
sleep states on some machines, from Kai-Heng Feng and Hans de
Goede.
12) Fix DST_NOCOUNT flag handling for ipv6 routes, from Peter
Oskolkov."
* gitolite.kernel.org:/pub/scm/linux/kernel/git/davem/net: (45 commits)
net/ipv6: do not copy dst flags on rt init
qmi_wwan: set DTR for modems in forced USB2 mode
clk: x86: Stop marking clocks as CLK_IS_CRITICAL
r8169: Get and enable optional ether_clk clock
clk: x86: add "ether_clk" alias for Bay Trail / Cherry Trail
r8169: enable ASPM on RTL8106E
r8169: Align ASPM/CLKREQ setting function with vendor driver
Revert "kcm: remove any offset before parsing messages"
kcm: remove any offset before parsing messages
net: ethernet: Fix a unused function warning.
net: dsa: mv88e6xxx: Fix ATU Miss Violation
tls: fix currently broken MSG_PEEK behavior
hv_netvsc: pair VF based on serial number
PCI: hv: support reporting serial number as slot information
bnxt_en: Fix VF mac address regression.
ipv6: fix possible use-after-free in ip6_xmit()
net: hp100: fix always-true check for link up state
ARM: dts: at91: add new compatibility string for macb on sama5d3
net: macb: disable scatter-gather for macb on sama5d3
net: mvpp2: let phylink manage the carrier state
...
DST_NOCOUNT in dst_entry::flags tracks whether the entry counts
toward route cache size (net->ipv6.sysctl.ip6_rt_max_size).
If the flag is NOT set, dst_ops::pcpuc_entries counter is incremented
in dist_init() and decremented in dst_destroy().
This flag is tied to allocation/deallocation of dst_entry and
should not be copied from another dst/route. Otherwise it can happen
that dst_ops::pcpuc_entries counter grows until no new routes can
be allocated because the counter reached ip6_rt_max_size due to
DST_NOCOUNT not set and thus no counter decrements on gc-ed routes.
Fixes: 3b6761d18b ("net/ipv6: Move dst flags to booleans in fib entries")
Cc: David Ahern <dsahern@gmail.com>
Acked-by: Wei Wang <weiwan@google.com>
Signed-off-by: Peter Oskolkov <posk@google.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When one vgpu is destroyed, its ggtt entries are not cleared.
This patch clears ggtt entries to avoid information leak.
v2: add 'Fixes' tag (Zhenyu)
Fixes: 2707e44466 ("drm/i915/gvt: vGPU graphics memory virtualization")
Signed-off-by: Zhipeng Gong <zhipeng.gong@intel.com>
Reviewed-by: Hang Yuan <hang.yuan@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Host prints lots of untracked MMIO at 0x4653c when creating linux guest.
"gvt: vgpu 2: untracked MMIO 0004653c len 4"
GEN9_CLKGATE_DIS_4 (0x4653c) is accessed by i915 for gmbus clockgating.
However vgpu doesn't support any clockgating powergating operations
on related mmio access trap so need add it to default handler.
GEN9_CLKGATE_DIS_4 is accessed in bxt_gmbus_clock_gating() which only
applies to GEN9_LP so doens't show the warning on other platforms.
The solution is to add it to default handler init_bxt_mmio_info().
Reviewed-by: He, Min <min.he@intel.com>
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
