Oded writes:
This tag contains the following fixes:
- Fix the code that checks whether we can use 2MB page size when mapping
memory in the ASIC's MMU. The current code had a "hole" which happened
in architectures other then x86-64.
- Fix the debugfs interface to read/write from/to the device using device
virtual addresses. There was a bug in the translation regarding
addresses that were mapped using 2MB page size.
- Fix a bug in the debug/profiling code, where the code didn't read the
full address but only the lower 32-bits of the address.
* tag 'misc-habanalabs-fixes-2019-06-06' of git://people.freedesktop.org/~gabbayo/linux:
habanalabs: Read upper bits of trace buffer from RWPHI
habanalabs: Fix virtual address access via debugfs for 2MB pages
habanalabs: fix bug in checking huge page optimization
Since GCC 9, the compiler warns about evolution of the
platform-specific ABI, in particular relating for the marshaling of
certain structures involving bitfields.
The kernel is a standalone binary, and of course nobody would be
so stupid as to expose structs containing bitfields as function
arguments in ABI. (Passing a pointer to such a struct, however
inadvisable, should be unaffected by this change. perf and various
drivers rely on that.)
So these warnings do more harm than good: turn them off.
We may miss warnings about future ABI drift, but that's too bad.
Future ABI breaks of this class will have to be debugged and fixed
the traditional way unless the compiler evolves finer-grained
diagnostics.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
According to the found documentation, data cache flushes and sync
instructions are needed on the PCX-U+ (PA8200, e.g. C200/C240)
platforms, while PCX-W (PA8500, e.g. C360) platforms aparently don't
need those flushes when changing the IO PDIR data structures.
We have no documentation for PCX-W+ (PA8600) and PCX-W2 (PA8700) CPUs,
but Carlo Pisani reported that his C3600 machine (PA8600, PCX-W+) fails
when the fdc instructions were removed. His firmware didn't set the NIOP
bit, so one may assume it's a firmware bug since other C3750 machines
had the bit set.
Even if documentation (as mentioned above) states that PCX-W (PA8500,
e.g. J5000) does not need fdc flushes, Sven could show that an Adaptec
29320A PCI-X SCSI controller reliably failed on a dd command during the
first five minutes in his J5000 when fdc flushes were missing.
Going forward, we will now NOT replace the fdc and sync assembler
instructions by NOPS if:
a) the NP iopdir_fdc bit was set by firmware, or
b) we find a CPU up to and including a PCX-W+ (PA8600).
This fixes the HPMC crashes on a C240 and C36XX machines. For other
machines we rely on the firmware to set the bit when needed.
In case one finds HPMC issues, people could try to boot their machines
with the "no-alternatives" kernel option to turn off any alternative
patching.
Reported-by: Sven Schnelle <svens@stackframe.org>
Reported-by: Carlo Pisani <carlojpisani@gmail.com>
Tested-by: Sven Schnelle <svens@stackframe.org>
Fixes: 3847dab774 ("parisc: Add alternative coding infrastructure")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 5.0+
Most I/O in the kernel is done using the kernel offset mapping.
However, there is one API that uses aliased kernel address ranges:
> The final category of APIs is for I/O to deliberately aliased address
> ranges inside the kernel. Such aliases are set up by use of the
> vmap/vmalloc API. Since kernel I/O goes via physical pages, the I/O
> subsystem assumes that the user mapping and kernel offset mapping are
> the only aliases. This isn't true for vmap aliases, so anything in
> the kernel trying to do I/O to vmap areas must manually manage
> coherency. It must do this by flushing the vmap range before doing
> I/O and invalidating it after the I/O returns.
For this reason, we should use the hardware lpa instruction to load the
physical address of kernel virtual addresses in the driver code.
I believe we only use the vmap/vmalloc API with old PA 1.x processors
which don't have a sba, so we don't hit this problem.
Tested on c3750, c8000 and rp3440.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 1be01d4a57 ("driver: base: Disable
CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
made default to 'n',
2. It is not recommended (help message: "This should not be used today
[...] creates a high system load") and was kept only for ancient
userland,
3. Certain userland specifically requests it to be disabled (systemd
README: "Legacy hotplug slows down the system and confuses udev").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Helge Deller <deller@gmx.de>
We only support I/O to kernel space. Using %sr1 to load the coherence
index may be racy unless interrupts are disabled. This patch changes the
code used to load the coherence index to use implicit space register
selection. This saves one instruction and eliminates the race.
Tested on rp3440, c8000 and c3750.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
Fix a s/TIF_SECOMP/TIF_SECCOMP/ comment typo
Cc: Jiri Kosina <trivial@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
We need to check whether drm_atomic_get_crtc_state() returns an error
pointer before dereferencing "crtc_st".
Fixes: 9e56030941 ("drm/komeda: Add komeda_plane/plane_helper_funcs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: "james qian wang (Arm Technology China)" <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/arm/display/komeda/komeda_plane.c: In function komeda_plane_atomic_check:
drivers/gpu/drm/arm/display/komeda/komeda_plane.c:49:22: warning: variable kcrtc set but not used [-Wunused-but-set-variable]
It is never used since introduction in
commit 9e56030941 ("drm/komeda: Add komeda_plane/plane_helper_funcs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Some chips have attributes which exist on more than one page but the
attribute is not presently marked as paged. This causes the attributes
to be generated with the same label, which makes it impossible for
userspace to tell them apart.
Marking all such attributes as paged would result in the page suffix
being added regardless of whether they were present on more than one
page or not, which might break existing setups. Therefore, we add a
second check which treats the attribute as paged, even if not marked as
such, if it is present on multiple pages.
Fixes: b4ce237b7f ("hwmon: (pmbus) Introduce infrastructure to detect sensors and limit registers")
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
update_lock is a mutex intended to protect write operations. It was not
taken, however, when _pmbus_write_word_data is called from
pmbus_set_samples() function which may cause problems especially when
some PMBUS_VIRT_* operation is implemented as a read-modify-write cycle.
This patch makes sure the lock is held during the operation.
Fixes: 49c4455dcc ("hwmon: (pmbus) Introduce PMBUS_VIRT_*_SAMPLES registers")
Signed-off-by: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
[groeck: Declared and initialized missing 'data' variable]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Drivers may register to hwmon and request for also registering
with the thermal subsystem (HWMON_C_REGISTER_TZ). However,
some of these driver, e.g. marvell phy, may be probed from
Device Tree or being dynamically allocated, and in the later
case, it will not have a dev->of_node entry.
Registering with hwmon without the dev->of_node may result in
different outcomes depending on the device tree, which may
be a bit misleading. If the device tree blob has no 'thermal-zones'
node, the *hwmon_device_register*() family functions are going
to gracefully succeed, because of-thermal,
*thermal_zone_of_sensor_register() return -ENODEV in this case,
and the hwmon error path handles this error code as success to
cover for the case where CONFIG_THERMAL_OF is not set.
However, if the device tree blob has the 'thermal-zones'
entry, the *hwmon_device_register*() will always fail on callers
with no dev->of_node, propagating -EINVAL.
If dev->of_node is not present, calling of-thermal does not
make sense. For this reason, this patch checks first if the
device has a of_node before going over the process of registering
with the thermal subsystem of-thermal interface. And in this case,
when a caller of *hwmon_device_register*() with HWMON_C_REGISTER_TZ
and no dev->of_node will still register with hwmon, but not with
the thermal subsystem. If all the hwmon part bits are in place,
the registration will succeed.
Fixes: d560168b5d ("hwmon: (core) New hwmon registration API")
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-hwmon@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Eduardo Valentin <eduval@amazon.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This reverts commit e9919a24d3.
Nathan reported the new behaviour breaks Android, as Android just add
new rules and delete old ones.
If we return 0 without adding dup rules, Android will remove the new
added rules and causing system to soft-reboot.
Fixes: e9919a24d3 ("fib_rules: return 0 directly if an exactly same rule exists when NLM_F_EXCL not supplied")
Reported-by: Nathan Chancellor <natechancellor@gmail.com>
Reported-by: Yaro Slav <yaro330@gmail.com>
Reported-by: Maciej Żenczykowski <zenczykowski@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Tested-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WoL magic packet configuration sometimes does not work due to
couple of leakages found.
Mainly there was a regression introduced during readx_poll refactoring.
Next, fw request waiting time was too small. Sometimes that
caused sleep proxy config function to return with an error
and to skip WoL configuration.
At last, WoL data were passed to FW from not clean buffer.
That could cause FW to accept garbage as a random configuration data.
Fixes: 6a7f227731 ("net: aquantia: replace AQ_HW_WAIT_FOR with readx_poll_timeout_atomic")
Signed-off-by: Nikita Danilov <nikita.danilov@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool_get_regs() allocates a buffer of size ops->get_regs_len(),
and pass it to the kernel driver via ops->get_regs() for filling.
There is no restriction about what the kernel drivers can or cannot do
with the open ethtool_regs structure. They usually set regs->version
and ignore regs->len or set it to the same size as ops->get_regs_len().
But if userspace allocates a smaller buffer for the registers dump,
we would cause a userspace buffer overflow in the final copy_to_user()
call, which uses the regs.len value potentially reset by the driver.
To fix this, make this case obvious and store regs.len before calling
ops->get_regs(), to only copy as much data as requested by userspace,
up to the value returned by ops->get_regs_len().
While at it, remove the redundant check for non-null regbuf.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot found the following leak in sctp_process_init
BUG: memory leak
unreferenced object 0xffff88810ef68400 (size 1024):
comm "syz-executor273", pid 7046, jiffies 4294945598 (age 28.770s)
hex dump (first 32 bytes):
1d de 28 8d de 0b 1b e3 b5 c2 f9 68 fd 1a 97 25 ..(........h...%
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000a02cebbd>] kmemleak_alloc_recursive include/linux/kmemleak.h:55
[inline]
[<00000000a02cebbd>] slab_post_alloc_hook mm/slab.h:439 [inline]
[<00000000a02cebbd>] slab_alloc mm/slab.c:3326 [inline]
[<00000000a02cebbd>] __do_kmalloc mm/slab.c:3658 [inline]
[<00000000a02cebbd>] __kmalloc_track_caller+0x15d/0x2c0 mm/slab.c:3675
[<000000009e6245e6>] kmemdup+0x27/0x60 mm/util.c:119
[<00000000dfdc5d2d>] kmemdup include/linux/string.h:432 [inline]
[<00000000dfdc5d2d>] sctp_process_init+0xa7e/0xc20
net/sctp/sm_make_chunk.c:2437
[<00000000b58b62f8>] sctp_cmd_process_init net/sctp/sm_sideeffect.c:682
[inline]
[<00000000b58b62f8>] sctp_cmd_interpreter net/sctp/sm_sideeffect.c:1384
[inline]
[<00000000b58b62f8>] sctp_side_effects net/sctp/sm_sideeffect.c:1194
[inline]
[<00000000b58b62f8>] sctp_do_sm+0xbdc/0x1d60 net/sctp/sm_sideeffect.c:1165
[<0000000044e11f96>] sctp_assoc_bh_rcv+0x13c/0x200
net/sctp/associola.c:1074
[<00000000ec43804d>] sctp_inq_push+0x7f/0xb0 net/sctp/inqueue.c:95
[<00000000726aa954>] sctp_backlog_rcv+0x5e/0x2a0 net/sctp/input.c:354
[<00000000d9e249a8>] sk_backlog_rcv include/net/sock.h:950 [inline]
[<00000000d9e249a8>] __release_sock+0xab/0x110 net/core/sock.c:2418
[<00000000acae44fa>] release_sock+0x37/0xd0 net/core/sock.c:2934
[<00000000963cc9ae>] sctp_sendmsg+0x2c0/0x990 net/sctp/socket.c:2122
[<00000000a7fc7565>] inet_sendmsg+0x64/0x120 net/ipv4/af_inet.c:802
[<00000000b732cbd3>] sock_sendmsg_nosec net/socket.c:652 [inline]
[<00000000b732cbd3>] sock_sendmsg+0x54/0x70 net/socket.c:671
[<00000000274c57ab>] ___sys_sendmsg+0x393/0x3c0 net/socket.c:2292
[<000000008252aedb>] __sys_sendmsg+0x80/0xf0 net/socket.c:2330
[<00000000f7bf23d1>] __do_sys_sendmsg net/socket.c:2339 [inline]
[<00000000f7bf23d1>] __se_sys_sendmsg net/socket.c:2337 [inline]
[<00000000f7bf23d1>] __x64_sys_sendmsg+0x23/0x30 net/socket.c:2337
[<00000000a8b4131f>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:3
The problem was that the peer.cookie value points to an skb allocated
area on the first pass through this function, at which point it is
overwritten with a heap allocated value, but in certain cases, where a
COOKIE_ECHO chunk is included in the packet, a second pass through
sctp_process_init is made, where the cookie value is re-allocated,
leaking the first allocation.
Fix is to always allocate the cookie value, and free it when we are done
using it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Reported-by: syzbot+f7e9153b037eac9b1df8@syzkaller.appspotmail.com
CC: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: netdev@vger.kernel.org
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When KASAN is enabled, after several rds connections are
created, then "rmmod rds_rdma" is run. The following will
appear.
"
BUG rds_ib_incoming (Not tainted): Objects remaining
in rds_ib_incoming on __kmem_cache_shutdown()
Call Trace:
dump_stack+0x71/0xab
slab_err+0xad/0xd0
__kmem_cache_shutdown+0x17d/0x370
shutdown_cache+0x17/0x130
kmem_cache_destroy+0x1df/0x210
rds_ib_recv_exit+0x11/0x20 [rds_rdma]
rds_ib_exit+0x7a/0x90 [rds_rdma]
__x64_sys_delete_module+0x224/0x2c0
? __ia32_sys_delete_module+0x2c0/0x2c0
do_syscall_64+0x73/0x190
entry_SYSCALL_64_after_hwframe+0x44/0xa9
"
This is rds connection memory leak. The root cause is:
When "rmmod rds_rdma" is run, rds_ib_remove_one will call
rds_ib_dev_shutdown to drop the rds connections.
rds_ib_dev_shutdown will call rds_conn_drop to drop rds
connections as below.
"
rds_conn_path_drop(&conn->c_path[0], false);
"
In the above, destroy is set to false.
void rds_conn_path_drop(struct rds_conn_path *cp, bool destroy)
{
atomic_set(&cp->cp_state, RDS_CONN_ERROR);
rcu_read_lock();
if (!destroy && rds_destroy_pending(cp->cp_conn)) {
rcu_read_unlock();
return;
}
queue_work(rds_wq, &cp->cp_down_w);
rcu_read_unlock();
}
In the above function, destroy is set to false. rds_destroy_pending
is called. This does not move rds connections to ib_nodev_conns.
So destroy is set to true to move rds connections to ib_nodev_conns.
In rds_ib_unregister_client, flush_workqueue is called to make rds_wq
finsh shutdown rds connections. The function rds_ib_destroy_nodev_conns
is called to shutdown rds connections finally.
Then rds_ib_recv_exit is called to destroy slab.
void rds_ib_recv_exit(void)
{
kmem_cache_destroy(rds_ib_incoming_slab);
kmem_cache_destroy(rds_ib_frag_slab);
}
The above slab memory leak will not occur again.
>From tests,
256 rds connections
[root@ca-dev14 ~]# time rmmod rds_rdma
real 0m16.522s
user 0m0.000s
sys 0m8.152s
512 rds connections
[root@ca-dev14 ~]# time rmmod rds_rdma
real 0m32.054s
user 0m0.000s
sys 0m15.568s
To rmmod rds_rdma with 256 rds connections, about 16 seconds are needed.
And with 512 rds connections, about 32 seconds are needed.
>From ftrace, when one rds connection is destroyed,
"
19) | rds_conn_destroy [rds]() {
19) 7.782 us | rds_conn_path_drop [rds]();
15) | rds_shutdown_worker [rds]() {
15) | rds_conn_shutdown [rds]() {
15) 1.651 us | rds_send_path_reset [rds]();
15) 7.195 us | }
15) + 11.434 us | }
19) 2.285 us | rds_cong_remove_conn [rds]();
19) * 24062.76 us | }
"
So if many rds connections will be destroyed, this function
rds_ib_destroy_nodev_conns uses most of time.
Suggested-by: Håkon Bugge <haakon.bugge@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Jianlin's testing, netperf was broken with 'Connection reset by peer',
as the cookie check failed in rt6_check() and ip6_dst_check() always
returned NULL.
It's caused by Commit 93531c6743 ("net/ipv6: separate handling of FIB
entries from dst based routes"), where the cookie can be got only when
'c1'(see below) for setting dst_cookie whereas rt6_check() is called
when !'c1' for checking dst_cookie, as we can see in ip6_dst_check().
Since in ip6_dst_check() both rt6_dst_from_check() (c1) and rt6_check()
(!c1) will check the 'from' cookie, this patch is to remove the c1 check
in rt6_get_cookie(), so that the dst_cookie can always be set properly.
c1:
(rt->rt6i_flags & RTF_PCPU || unlikely(!list_empty(&rt->rt6i_uncached)))
Fixes: 93531c6743 ("net/ipv6: separate handling of FIB entries from dst based routes")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the topo:
h1 ---| rp1 |
| route rp3 |--- h3 (192.168.200.1)
h2 ---| rp2 |
If rp1 bc_forwarding is set while rp2 bc_forwarding is not, after
doing "ping 192.168.200.255" on h1, then ping 192.168.200.255 on
h2, and the packets can still be forwared.
This issue was caused by the input route cache. It should only do
the cache for either bc forwarding or local delivery. Otherwise,
local delivery can use the route cache for bc forwarding of other
interfaces.
This patch is to fix it by not doing cache for local delivery if
all.bc_forwarding is enabled.
Note that we don't fix it by checking route cache local flag after
rt_cache_valid() in "local_input:" and "ip_mkroute_input", as the
common route code shouldn't be touched for bc_forwarding.
Fixes: 5cbf777cfd ("route: add support for directed broadcast forwarding")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vm test build fails when test is built by itself using
make -C tools/testing/selftests/vm
or
cd tools/testing/selftests/vm; make
When the test is built invoking its Makefile directly, it defines
OUTPUT which conflicts with lib.mk's logic to install headers.
make --no-builtin-rules INSTALL_HDR_PATH=$OUTPUT/usr \
ARCH=x86 -C ../../../.. headers_install
make[1]: Entering directory '/mnt/data/lkml/linux_5.2'
REMOVE shmparam.h
rm: cannot remove '/usr/include/asm-generic/shmparam.h': Permission denied
scripts/Makefile.headersinst:96: recipe for target '/usr/include/asm-generic/.install' failed
make[3]: *** [/usr/include/asm-generic/.install] Error 1
scripts/Makefile.headersinst:32: recipe for target 'asm-generic' failed
make[2]: *** [asm-generic] Error 2
Makefile:1199: recipe for target 'headers_install' failed
make[1]: *** [headers_install] Error 2
make[1]: Leaving directory '/mnt/data/lkml/linux_5.2'
../lib.mk:52: recipe for target 'khdr' failed
make: *** [khdr] Error 2
Fixes: 8ce72dc325 ("selftests: fix headers_install circular dependency")
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
This Kselftest update for Linux 5.2-rc4 consists of
- Alex Shi's fixes to cgroup tests
- Alakesh Haloi's fix to userfaultfd compiler warning
- Naresh Kamboju's fix to vm install to include test script to run
the test.
-----BEGIN PGP SIGNATURE-----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=9KtO
-----END PGP SIGNATURE-----
Merge tag 'linux-kselftest-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull Kselftest fixes from Shuah Khan:
- fixes to cgroup tests (Alex Shi)
- fix to userfaultfd compiler warning (Alakesh Haloi)
- fix to vm install to include test script to run the test (Naresh
Kamboju)
* tag 'linux-kselftest-5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: vm: install test_vmalloc.sh for run_vmtests
userfaultfd: selftest: fix compiler warning
kselftest/cgroup: fix incorrect test_core skip
kselftest/cgroup: fix unexpected testing failure on test_core
kselftest/cgroup: fix unexpected testing failure on test_memcontrol
-----BEGIN PGP SIGNATURE-----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=KySr
-----END PGP SIGNATURE-----
Merge tag 'pidfd-fixes-v5.2-rc4' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux
Pull pidfd fixes from Christian Brauner:
"The contains two small patches to the pidfd samples and test binaries
respectively.
They were lacking appropriate ifdefines for __NR_pidfd_send_signal and
could hence lead to compilation errors when that was not defined.
This was spotted on mips independently by Guenter Roeck (who was kind
enough to send a fix for the samples binary) and Arnd who spotted it
in linux-next.
Apart from these two patches, there's also a patch to update the
comments for the pidfd_send_signal() syscall which were slightly
wrong/inconsistenly worded"
* tag 'pidfd-fixes-v5.2-rc4' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
tests: fix pidfd-test compilation
signal: improve comments
samples: fix pidfd-metadata compilation
Use hverkuil-cisco@xs4all.nl instead of hans.verkuil@cisco.com.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Use hverkuil-cisco@xs4all.nl instead of hans.verkuil@cisco.com.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The class_ptr will be NULL if pvr2_sysfs_class_create() fails
in pvr_init(), when call pvr2_sysfs_class_destroy(), it will
lead to null-ptr-deref, fix it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Since locking is handled by regmap, the spin_lock_irqsave() in the
meson_ao_cec_g12a_read/write() regmap callbacks is not needed.
Fixes: b7778c4668 ("media: platform: meson: Add Amlogic Meson G12A AO CEC Controller driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of ioremap failure, the core code will take care of printing
the error message, so there is no need for having a local error
message in the driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The CSI registers are 32-bit, so using u32 type is more suitable
for storing the values from register reads.
Switch from 'unsigned long' to 'u32' type.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently there is a macro for reading and another macro for writing
to the CSI registers.
Functions can do parameter type checking, which leads to a safer code,
so switch from macro to function implementation.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Rui Miguel Silva <rmfrfs@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
In case of watchdog timeout detected while doing mode detection,
it's better triggering video engine hardware reset immediately so
this commit fixes code for the case. Other than the case, it will
trigger video engine hardware reset after RESOLUTION_CHANGE_DELAY.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
There are cases that interrupt bits are cleared by a 500ms delayed
work which causes unnecessary irq calls. Also, the current
interrupt handler returns IRQ_HANDLED always but it should return
IRQ_NONE if there is any unhandled interrupt. So this commit
refines the interrupt handling logic to fix these issues.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
- Avoid NULL deref when unloading/reloading ramoops module (Pi-Hsun Shih)
- Run ramoops without crash dump region
-----BEGIN PGP SIGNATURE-----
Comment: Kees Cook <kees@outflux.net>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=g26W
-----END PGP SIGNATURE-----
Merge tag 'pstore-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull pstore fixes from Kees Cook:
- Avoid NULL deref when unloading/reloading ramoops module (Pi-Hsun
Shih)
- Run ramoops without crash dump region
* tag 'pstore-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
pstore/ram: Run without kernel crash dump region
pstore: Set tfm to NULL on free_buf_for_compression
VE_INTERRUPT_CAPTURE_COMPLETE and VE_INTERRUPT_COMP_COMPLETE are
not set at the same time but the current interrupt handling
mechanism of this driver doesn't clear the interrupt flag until
both two are set, and this behavior causes unnecessary interrupt
handler calls. In fact, this driver provides JPEG format only so
taking care of the VE_INTERRUPT_COMP_COMPLETE is enough for getting
compressed image frame so this commit gets rid of the
VE_INTERRUPT_CAPTURE_COMPLETE checking logic to simplify the logic.
Handling of VE_INTERRUPT_CAPTURE_COMPLETE could be added back later
when it's actually needed.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver prints out too much log messages when a
mode change happens, video turned off by screen saver and etc.
Actually, all cases are reported to user space properly. Also,
these are not critical errors but recoverable things, so this
commit changes the log level of some noisy printing outs.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Video Engine has a dedicated interrupt line so this driver doesn't
need to use IRQF_SHARED flag so remove it. Also, it'd be good for
following what Thomas recommended in the IRQF_ONESHOT support
patch like below:
"Note that for now IRQF_ONESHOT cannot be used with IRQF_SHARED to
avoid complex accounting mechanisms."
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Differently from other Aspeed drivers, this driver calls clock
control APIs in interrupt context. Since ECLK is coupled with a
reset bit in clk-aspeed module, aspeed_clk_enable will make 10ms of
busy waiting delay for triggering the reset and it will eventually
disturb other drivers' interrupt handling. To fix this issue, this
commit changes this driver's irq to threaded irq so that the delay
can be happened in a thread context.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Currently, this driver calls clk_prepare and clk_unprepare from
interrupt context too but these should be called from sleepable
context only. To fix this issue, this commit splits out
clk_enable/disable and clk_prepare/unprepare, and it places
clk_prepare/unprepare calls into the module probe/remove function.
Signed-off-by: Jae Hyun Yoo <jae.hyun.yoo@linux.intel.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
This patch shouldn't have been included in the pull request as it adds
a non-standard raw mode that is for debugging only. So revert
commit ead14a7075.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
The assigment of FB_VMODE_NONINTERLACE to var->vmode should be a
bit-wise or of FB_VMODE_NONINTERLACE instead of an assignment,
otherwise the previous clearing of the FB_VMODE_MASK bits of
var->vmode makes no sense and is redundant.
Addresses-Coverity: ("Unused value")
Fixes: ad4e02d508 ("[media] vivid: add a simple framebuffer device for overlay testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
MT8183 will use a multi-planar format backed by a single buffer. Adapt
the existing code to be able to handle such frames instead of assuming
each frame is backed by two buffers.
Co-developed-by: Alexandre Courbot <acourbot@chromium.org>
[acourbot: refactor, cleanup and split]
Signed-off-by: Yunfei Dong <yunfei.dong@mediatek.com>
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
[hverkuil-cisco@xs4all.nl: fix checkpatch alignment warning]
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Formats are read-only internal memory structures, so make them const.
Signed-off-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
If we only set the max_segment_size on the queue an IOMMU merge might
create bigger segments again, so limit the IOMMU merges as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If we only set the max_segment_size on the queue an IOMMU merge might
create bigger segments again, so limit the IOMMU merges as well.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
