Using a clear page for scratch means that we have relatively benign
errors in case it is accidentally used, but that can be rather too
benign for debugging. If we poison the scratch, ideally it quickly
results in an obvious error.
v2: Set each page individually just in case we are using highmem for our
scratch page.
v3: Pick a new scratch register as MI_STORE_REGISTER_MEM does not work
with GPR0 on gen7, unbelievably.
v4: Haswell still considers 3DPRIM a privileged register!
Suggested-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200124115133.53360-1-chris@chris-wilson.co.uk
Due to the asynchronous nature of releasing our wakerefs, we can signal
the main GT wakeref as complete before the individual engines have
cleared their own wakerefs. During shutdown we assert that the engines
are indeed parked before we release them, but for this to be always true
we need to flush their workers as well.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200124143339.140988-1-chris@chris-wilson.co.uk
Perhaps in some cases the BIOS/GOP or other firmware may turn on
PHY A but may not program the MUX correctly. Therefore, re-program
PHY A if it is determined after reading the VBT that the value
programmed for the MUX bit does not match the expected value.
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121235848.8457-1-vivek.kasireddy@intel.com
A recent change in BSpec allow us to change EXTLINE while transcoder
is enabled so this allow us to change it even when doing the first
fastset after taking over previous hardware state set by BIOS.
BIOS don't enable PSR, so if sink supports PSR it will be enabled on
the first fastset, so moving the EXTLINE compute and set to PSR flows
allow us to simplfy a bunch of code.
This will save a lot of time in all the IGT tests that uses CRC, as
when PSR2 is enabled CRCs are not generated, so we switch to PSR1, so
the previous code would compute dc3co_exitline=0 causing a full
modeset that would shutdown pipe, enable and train link.
v2: only programming EXTLINE when DC3CO is enabled
BSpec: 49196
Cc: Imre Deak <imre.deak@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200122182617.18597-2-jose.souza@intel.com
This will calculaet the DC3CO exit delay only once per full modeset.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200122182617.18597-1-jose.souza@intel.com
Remove the i2c_bus_num >= 0 check from the adapter lookup function
as this would prevent ACPI bus number override. This check was mainly
there to return early if the bus number has already been found but we
anyway return in the next line if the slave address does not match.
Fixes: 8cbf89db29 ("drm/i915/dsi: Parse the I2C element from the VBT MIPI sequence block (v3)")
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Nabendu Maiti <nabendu.bikash.maiti@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Bob Paauwe <bob.j.paauwe@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200118005848.20382-1-vivek.kasireddy@intel.com
Optimistically wait for the prior vma activity before taking the mutex
to minimise the mutex hold time while unbinding. We will then verify the
vma is idle with a second wait under the mutex to ensure it is safe to
unbind.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123224459.38128-2-chris@chris-wilson.co.uk
Only assert that the i915_vma is now idle if and only if no other pins
are present. If another user has the i915_vma pinned, they may submit
more work to the i915_vma skipping the vm->mutex used to serialise the
unbind. We need to wait again, if we want to continue and unbind this
vma.
However, if we own the i915_vma (we hold the vm->mutex for the unbind
and the pin_count is 0), we can assert that the vma remains idle as we
unbind.
Fixes: 2850748ef8 ("drm/i915: Pull i915_vma_pin under the vm->mutex")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/530
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123224459.38128-1-chris@chris-wilson.co.uk
If the ctx->vm is freed before we can acquire a local reference to it,
we proceed to call i915_vm_put(NULL), which is invalid.
Reported-by: Colin Ian King <colin.king@canonical.com>
Fixes: 5dbd2b7be6 ("drm/i915/gem: Convert vm idr to xarray")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123152602.1432282-1-chris@chris-wilson.co.uk
Include the current RC6 residency counter in the error message, so that
if we fail to park and manually enter RC6 we can see if the counter has
a particularly suspect value (such as 0).
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Andi Shyti <andi.shyti@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123145755.1420622-1-chris@chris-wilson.co.uk
In the port sync mode, for the master crtc, the master_transcoder is INVALID.
In that case since its value is -1, do not set the bit in the bitmask.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d0eed1545f ("drm/i915: Fix post-fastset modeset check for port sync")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200123002415.31478-1-manasi.d.navare@intel.com
Add convenience helpers for the most common uncore operations with
struct drm_i915_private * as context rather than struct intel_uncore *.
The goal is to replace all instances of I915_READ(),
I915_POSTING_READ(), I915_WRITE(), I915_READ_FW(), and I915_WRITE_FW()
in display/ with these, to finally be able to get rid of the implicit
dev_priv local parameter use.
The idea is that any non-u32 reads or writes are special enough that
they can use the intel_uncore_* functions directly.
v2:
- rename the file intel_de.h
- move intel_de_wait_for_* there too
- also add de fw helpers
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200121113915.9813-1-jani.nikula@intel.com
Just a couple of fixes to GP10x ACR support after the work, and a
(fairly severe if you're running piglit a lot) memory leak fix.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <skeggsb@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <CACAvsv51mZaRuT5R=VhbKSTPzd15L4FbDiPQ+wsF+C23c_fOAQ@mail.gmail.com
- it changes enable and disable callback functions names of
struct exynos_drm_crtc_ops to atomic_enable and atomic_disable
for consistency.
Modify "EXYNOS" prefix to "Exynos"
- "Exynos" name is a regular trademarked name promoted by its
manufacturer, Samsung Electronics Co., Ltd.. This patch
corrects the name.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tE0S
-----END PGP SIGNATURE-----
Merge tag 'exynos-drm-next-for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/daeinki/drm-exynos into drm-next
Change Exynos DRM specific callback function names
- it changes enable and disable callback functions names of
struct exynos_drm_crtc_ops to atomic_enable and atomic_disable
for consistency.
Modify "EXYNOS" prefix to "Exynos"
- "Exynos" name is a regular trademarked name promoted by its
manufacturer, Samsung Electronics Co., Ltd.. This patch
corrects the name.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1579567970-4467-1-git-send-email-inki.dae@samsung.com
If CONFIG_IOMMU_API is n, build fails:
vers/gpu/drm/nouveau/nvkm/subdev/ltc/gp10b.c:37:9: error: implicit declaration of function dev_iommu_fwspec_get; did you mean iommu_fwspec_free? [-Werror=implicit-function-declaration]
spec = dev_iommu_fwspec_get(device->dev);
^~~~~~~~~~~~~~~~~~~~
iommu_fwspec_free
drivers/gpu/drm/nouveau/nvkm/subdev/ltc/gp10b.c:37:7: warning: assignment makes pointer from integer without a cast [-Wint-conversion]
spec = dev_iommu_fwspec_get(device->dev);
^
drivers/gpu/drm/nouveau/nvkm/subdev/ltc/gp10b.c:39:17: error: struct iommu_fwspec has no member named ids
u32 sid = spec->ids[0] & 0xffff;
Seletc IOMMU_API under config DRM_NOUVEAU to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drivers/gpu/drm/nouveau/dispnv04/arb.c: In function nv04_calc_arb:
drivers/gpu/drm/nouveau/dispnv04/arb.c:56:21: warning:
variable width set but not used [-Wunused-but-set-variable]
'width' is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
drivers/gpu/drm/nouveau/dispnv50/disp.c: In function nv50_pior_enable:
drivers/gpu/drm/nouveau/dispnv50/disp.c:1672:28: warning:
variable nv_connector set but not used [-Wunused-but-set-variable]
commit ac2d9275f3 ("drm/nouveau/kms/nv50-: Store the
bpc we're using in nv50_head_atom") left behind this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
gp10b doesn't have all the registers that gp102_gr_zbc wants to access,
which causes IBUS MMIO faults to occur. Avoid this by using the gp100
variants of grctx and gr_zbc.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The low-level Falcon bootstrapping callbacks are expected to return 0 on
success or a negative error code on failure. However, the implementation
on Tegra returns the ID or mask of the Falcons that were bootstrapped on
success, thus breaking the calling code, which treats this as failure.
Fix this by making sure we only return 0 or a negative error code, just
like the code for discrete GPUs does.
Fixes: 86ce2a7153 ("drm/nouveau/flcn/cmdq: move command generation to subdevs")
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
[why]
FMT has limitation to support YCbCr420 with h_active greater than 4096.
[how]
Use odm combine to overcome the limitation.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver didn't init hw i2c speed cause hdcp hw cannot
send command, because the default value of speed register
is 0x2.
[How]
Restore the default speed when release i2c engine
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
MPO isn't enabled on some 4k videos due to video source width is 4096
and the current limit is 3840.
[How]
Changed the limit to 4096.
Signed-off-by: Isabel Zhang <isabel.zhang@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
MSA will be deprecated in the future.
Need to support VSC during DP test automation.
[how]
Do not disable VSC during DP test automation.
TODO - need to add VSC update on DM side on test request.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
CW2 may already be programmed when coming back from S4. In this case
we want to unconditionally replace whatever DMCUB version is currently
enabled with the latest.
[How]
Check the hw_init flag to know whether or not we've previously executed
the initliazed routine.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
These logically make sense more to be set after the DMCUB has been
reset rather than when we setup the inbox.
[How]
Move them into the reset callback.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DMCUB command table doesn't support ATOM_ENABLE/ATOM_DISABLE anymore
so we never end up calling the DCN init path in DMCUB.
[How]
Map ATOM_ENABLE to ATOM_INIT only for DMCUB command table offloading.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We'll need this to perform a clean shutdown before unloading the driver.
[How]
It will call reset internally and set hw_init to false. It won't do
anything if the hardware isn't initialized.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
determine_update_type_for_commit() uses pointers to single instance
of local variable to fill scaling/color info for all planes updates.
This is a bug, that leads to incorrect update type for commit in case
of multiple planes per crtc.
Each plane should refer to separate scaling/color data.
[How]
Use arrays for plane properties.
Bundle all properties into a single structure to simplify memory allocation.
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoded fixed values are not proper.
[How]
Use enum values instead of fixed numbers.
Signed-off-by: Brandon Syu <Brandon.Syu@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In HG mode, vbios didn't call DispController_Init to program NV1x
XTAL_REF_DIV value when ASIC_INIT, but driver read XTAL_REF_DIV
to calculate i2c reference frequency. it cause i2c frequency change
from 100kHz to 200kHz.
[How]
remove get_speed function and calculate reference frequency at
set_speed functiton.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
It has duplicate code for building regamma curve
[How]
Remove the duplicate code and use the same function for building regamma
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The types for dummyinteger1 and dummyinteger2 are unsigned
as part of the DML spec. They should not be long.
[How]
Make them unsigned int instead of long.
Signed-off-by: Jerry (Fangzhi) Zuo <Jerry.Zuo@amd.com>
Reviewed-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For DMCUB enabled hardware DC has a dependency on DMCUB already being
running.
Command table offloading will fail on first modeset if DMCUB isn't
initialized first.
[How]
Perform DMCUB hardware initialization before DC.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver use pipe_ctx to reallocate payload may cause allocate
payload twice on same sink with split pipe.
[How]
Drvier must to check pipe_ctx is split pipe or not to avoid
reallocate payload twice on same sink.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
If the command table isn't available then we can fallback to DMCUB
offloading if it's enabled and available.
[How]
Instead of assigning NULL for supported command table functions we can
fallback to the DMCUB when it's available.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Under some hardware initialization sequences the fb base/fb offset
provided can be zero or hardwareinit can happen too late.
We want to ensure that we always have the correct fb_base/fb_offset
when performing DMCUB hardware initialization so we can do DMCUB
command table offloading during first dc hardware init.
[How]
Read from the DCN registers. VBIOS already filled these in for us.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Empty dsc enc caps when debug option is set to disable DSC.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The DP 1.4a Spec requires that training pattern only under certain
specific conditions. Currently driver will re-send
training pattern every time voltage swing value changes,
but that should not be the case.
[How]
Do not re-send training pattern every time VS values
are different. Only send it on the first iteration.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Abdoulaye Berthe <Abdoulaye.Berthe@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
On video test pattern request we need to update MSA and VSC so
it will match the requested test pattern dynamic range field.
[how]
Update dynamic range field in MSA and disable VSC as updating VSC
info packet is complicated and not required for test pattern purpose.
Signed-off-by: Wenjing Liu <Wenjing.Liu@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
