Keep the driver internals in C file. Currently it's not required for
drivers to know rx or tx a channel is, except create function.
So correct "channel create" function, and use all channel struct
macroses only for internal use.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw h/w supports up to 8 tx and 8 rx channels. This patch adds
multi-queue support to the driver only, shaper configuration will
be added with separate patch series. Default shaper mode, as
before, priority mode, but with corrected priority order, 0 - is
highest priority, 7 - lowest.
The poll function handles all unprocessed channels, till all of
them are free, beginning from hi priority channel.
In dual_emac mode the channels are shared between two network devices,
as it's with single-queue default mode.
The statistic for every channel can be read with:
$ ethtool -S ethX
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The interrupts shouldn't be disabled while receiving skb, but while
ctrl_stop, the channels are stopped and all remaining packets are
handled with netif_receive_skb(), it can cause WARN_ONCE when ctrl
is stopping while not all packets were handled with NAPIs:
lock_irq_save
cpdma_ctlr_stop
cpdma_chan_top
__cpdma_chan_free
cpsw_rx_handler
netif_receive_skb
So, split locking while ctrl stop thus interrupts are still
enabled while skbs handling. It can cause WARN_ONCE in rare
cases when ctrl is stopping while not all packets were handled
with NAPIs.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tx channels share same pool of descriptors. Thus one channel can
block another if pool is emptied by one. But, the shaper should
decide which channel is allowed to send packets. To avoid such
impact of one channel on another, let every channel to have its
own piece of pool.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor overlapping changes for both merge conflicts.
Resolution work done by Stephen Rothwell was used
as a reference.
Signed-off-by: David S. Miller <davem@davemloft.net>
The ale, cpts, version, rx_packet_max, bus_freq, interrupt pacing
parameters are common per net device that uses the same h/w. So,
move them to common driver structure.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The napi structs are common for both net devices in dual_emac
mode, In order to not hold duplicate links to them, move to
cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These data are common for net devs in dual_emac mode. No need to hold
it for every priv instance, so move them under cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The irq data are common for net devs in dual_emac mode. So no need to
hold these data in every priv struct, move them under cpsw_common.
Also delete irq_num var, as after optimization it's not needed.
Correct number of irqs to 2, as anyway, driver is using only 2,
at least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Every net device private struct holds links to shared cpdma resources.
No need to save and every time synchronize these resources per net dev.
So, move it to common driver struct.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The pointers on h/w registers are common for every cpsw_private
instance, so no need to hold them for every ndev.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to hold pdev link when only dev is needed.
This allows to simplify a bunch of cpsw->pdev->dev now and farther.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simply create holder for common data and as a start moves
pdev var to it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No need to check const slave num in runtime for every packet,
and ndev for slaves w/o ndev is anyway NULL. So remove redundant
check and macro.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to hold link to clk, it's used only once
while probe.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need in priv here.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
At poll handler no possibility to figure out which network device is
handling packets, as cpdma channels are common for both network
devices in dual_emac mode. Currently, the messages are printed only
for one device, in fact, there is two. This print msg is incorrect
and seems is not very useful, so drop it from poll handler.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As second net dev is created only in case of dual_emac mode, port
number can be figured out in simpler way. Also no need to pass
redundant ndev struct.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparatory patch for converting qdisc linked list into a
hashtable. As we'll need to include hashtable.h in netdevice.h, we first
have to make sure that this will not introduce symbol conflicts for any of
the netdevice.h users.
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
The struct cpdma_desc_pool->used_desc field can be safely removed from
CPDMA driver (and hot patch) because used_descs counter is used just
for pool consistency check at CPDMA deinitialization and now this
check can be re-implemnted using gen_pool_size(pool->gen_pool) !=
gen_pool_avail(pool->gen_pool).
More over, this will allow to get rid of warnings in
cpdma_desc_pool_destro()-> WARN_ON(pool->used_desc) which may happen
because the used_descs is used unprotected, since CPDMA has been
switched to use genalloc, and may get wrong values on SMP.
Hence, remove used_desc from struct cpdma_desc_pool.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_node_put needs to be called when the device node which is got
from of_parse_phandle has finished using.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use of_platform_depopulate() in cpsw_remove() instead of
of_device_unregister(), because CSPW child devices will not be
recreated otherwise on next insmod. of_platform_depopulate() is
correct way now as it will ensure that all steps done in
of_platform_populate() are reverted, including cleaning up of
OF_POPULATED flag.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The L3 error will be generated and system will crash during unloading
of CPSW driver if CPSW is used as module and ethX devices are down.
This happens because CPSW can be power off by PM runtime now when ethX
devices are down.
Hence, ensure that CPSW powered up by PM runtime before performing any
deinitialization actions which require CPSW registers access. In case
of PM runtime error just leave cpsw_remove() as we can't do anything
anymore.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix deadlock in cpdma_ctlr_destroy() which is triggered now on
cpsw module removal:
cpsw_remove()
- cpdma_ctlr_destroy()
- spin_lock_irqsave(&ctlr->lock, flags)
- cpdma_ctlr_stop()
- spin_lock_irqsave(&ctlr->lock, flags);
- cpdma_chan_destroy()
- spin_lock_irqsave(&ctlr->lock, flags);
The issue has not been observed before because CPDMA channels have
been destroyed manually by CPSW until commit d941ebe88a ("net:
ethernet: ti: cpsw: use destroy ctlr to destroy channels") was merged.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Such a big dump of register values is hardly useful on a production
system.
Another downside of the now removed functions is that calling
emac_dump_regs resulted in at least 87 calls to dev_info while holding a
spinlock and having irqs off which is a big source of latency.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing free_netdev() before return from function
cpmac_probe() in the error handling case.
This patch revert commit 0465be8f4f ("net: cpmac: fix in
releasing resources"), which changed to only free_netdev
while register_netdev failed.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 'cpmac_open', 'dma_alloc_coherent' has been used to allocate some
resources, so we need to free them using 'dma_free_coherent' instead
of 'kfree'.
Also, we don't need to free these resources if the allocation has failed.
So I have slighly modified the goto label in this case.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
TI_CPSW_PHY_SEL depended on TI_CPSW and was selected by the latter. So
there is no reason to have this symbol visible.
A further optimisation would be to put the code for both symbols into a
single module which would allow to not export at least cpsw_phy_sel()
and simplify the module load process.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
There was a check on CAP_NET_ADMIN in cpmac_set_settings, but this
check is already done in dev_ethtool, so no need to repeat it before
calling the generic function.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two generics functions phy_ethtool_{get|set}_link_ksettings,
so we can use them instead of defining the same code in the driver.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
TI CPDMA currently uses a bitmap for tracking descriptors alloactions
allocations, but The genalloc already handles the same and can be used
as with special memory (SRAM) as with DMA cherent memory chank
(dma_alloc_coherent()). Hence, switch to using genalloc and add
desc_num property for each channel for limitation of max number of
allowed descriptors for each CPDMA channel. This patch do not affect
on net throuput.
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Tested-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use "ti,cpsw-mdio" to enable PM runtime auto-suspend on supported
platforms, where MDIO is implemented as part of TI CPSW.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Davinci MDIO is always used as slave device which services
read/write requests from MDIO/PHY core. It doesn't use IRQ also.
As result, It's possible to relax PM runtime constraints for Davinci
MDIO and enable it on demand, instead of powering it during probe
and powering off during removal.
Hence, implement PM runtime autosuspend for Davinci MDIO, but keep it
disabled by default, because Davinci MDIO is integrated in big set of
TI devices and not all of them expected to work corectly with RPM
autosuspend enabled:
- expected to work on SoCs where MDIO is part of TI CPSW
(cpsw.c DRA7/am57x, am437x, am335x, dm814x)
- not verified on Keystone 2 and other SoCs where MDIO is used with TI EMAC IP
(davinci_emac.c: dm6467-emac, am3517-emac, dm816-emac).
Davinci MDIO RPM autosuspend can be enabled through sysfs:
echo 100 > /sys/devices/../48484000.ethernet/48485000.mdio/power/autosuspend_delay_ms
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PM runtime .runtime_suspend()/.runtime_resume() callbacks and
perform Davinci MDIO enabling/disabling from these callbacks. This
allows to reuse pm_runtime_force_suspend/resume() APIs during System
suspend and required for further implementation of PM runtime
autosuspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Davinci MDIO MDIO_CONTROL.CLKDIV can be calculated only once
during probe, hence split __davinci_mdio_reset() on
davinci_mdio_init_clk() and davinci_mdio_enable(). Initialize and
save CLKDIV in .probe(). Then just use saved value.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's not expected Davinci MDIO to be accessible after its suspend
callbacks have been called:
- all consumers of Davinci MDIO will stop/disconnect phys at Device
suspend stage;
- all phys are expected to be suspned already by PHY/MDIO core;
- MDIO locking is done by MDIO Bus code.
Hence, it's safe to drop "suspended" and "lock" fields from mdio_data.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is disabled when Davinci MDIO .suspend_late() and
.resume_early() callbacks are called. As result, any PM runtime calls here will
be just a nop and can be removed.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do PM runtime initialization later in probe - this allows to simplify
error handling a bit.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through net_device_ops interfce. In
this case net_device_ops operations requiring registers access will
cause L3 errors and CPSW crash.
Hence, fix it by adding RPM get/put calls in net_device_ops callbacks
which need to access CPSW registers: .ndo_set_mac_address(),
.ndo_vlan_rx_add_vid(), .ndo_vlan_rx_kill_vid().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW might be suspended by RPM if all ethX interfaces are down,
but it still could be accesible through ethtool interfce. In this case
ethtool operations, requiring registers access, will cause L3 errors and
CPSW crash.
ethtool callbcaks which need to access CPSW registers now:
.set_coalesce(), .get_ethtool_stats(), .set_pauseparam(), .get_regs()
Hence, fix it by adding .begin()/.complete() ethtool callbacks, which
will be called before/after each ethtool operation runs, and do CPSW
RPM handling in these callbacks. That way CPSW will be active while
handling ethtool requests.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PM runtime is properly handled in cpsw_ndo_open/stop(), as result it
isn't required to duplicate these calls in .suspend()/.resume()
callbacks. Moreover, it might cause unnecessary RPM resume of CPSW
during System suspend in the case it's already suspended because
all ethX interfaces are down already, before System suspend started.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missed check of return code from PM runtime get() calls.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw_suspend() could trigger L3 error and CPSW will stop
functioning if System enters suspend when all ethX net-devices are
down - in this case CPSW could be already suspended by PM runtime, but
cpsw_suspend() will try to call soft_reset_slave() unconditionally
and access CPSW registers.
Hence, fix it by moving soft_reset_slave() from cpsw_suspend() to
cpsw_slave_stop(). This way slave ports will be reset when CPSW is
active and will be in proper state during Suspend.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dual MAC devices don't necessarily have both MACs wired up, so ignore
those that are disabled.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason in rx_descs property because davinici_cpdma
driver splits pool of descriptors equally between tx and rx channels.
That is, if number of descriptors 256, 128 of them are for rx
channels. While receiving, the descriptor is freed to the pool and
then allocated with new skb. And if in DT the "rx_descs" is set to
64, then 128 - 64 = 64 descriptors are always in the pool and cannot
be used, for tx, for instance. It's not correct resource usage,
better to set it to half of pool, then the rx pool can be used in
full. It will not have any impact on performance, as anyway, the
"redundant" descriptors were unused.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a warning for tlan_handle_tx_eoc when building with "make W=1"
drivers/net/ethernet/ti/tlan.c: In function 'tlan_handle_tx_eoc':
drivers/net/ethernet/ti/tlan.c:1647:59: error: parameter 'host_int' set but not used [-Werror=unused-but-set-parameter]
static u32 tlan_handle_tx_eoc(struct net_device *dev, u16 host_int)
This is harmless, but removing the unused assignment lets us avoid
the warning with no downside.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to destroy channels that are destroyed while
cpdma_ctlr destroy. In this case no need to remember how much
channels where created and destroy them by one, as cpdma_ctlr
destroys all of them.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/sched/act_police.c
net/sched/sch_drr.c
net/sched/sch_hfsc.c
net/sched/sch_prio.c
net/sched/sch_red.c
net/sched/sch_tbf.c
In net-next the drop methods of the packet schedulers got removed, so
the bug fixes to them in 'net' are irrelevant.
A packet action unload crash fix conflicts with the addition of the
new firstuse timestamp.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason in this lock. At least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx-usecs shouldn't be changed while interface down/up.
Currently, for instance, if it's set to 100us, after interface
down/up it's 500us. It's a hidden bug that can lead to lavish
interrupt pacing time increasing while "down/up" up to max value.
Steps to reproduce:
- set rx-usecs to be 100us
- down/up interface
- read new unexpected rx-usecs
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
If a fixed-link DT subnode is used, the phy_device was looked up so
that a PHY ID string could be constructed and passed to phy_connect().
This is not necessary, as the device_node can be passed directly to
of_phy_connect() instead. This reuses the same codepath as if the
phy-handle DT property was used.
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy-mode emac property was only being processed in the phy_id
or fixed-link cases. However if phy-handle was specified instead,
an error message would complain about the lack of phy_id or
fixed-link, and then jump past the of_get_phy_mode(). This would
result in the PHY mode defaulting to MII, regardless of what the
devicetree specified.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If an emac node has a phy-handle property that points to something
which is not a phy, then a segmentation fault will occur when the
interface is brought up. This is because while phy_connect() will
return ERR_PTR() on failure, of_phy_connect() will return NULL.
The common error check uses IS_ERR(), and so missed when
of_phy_connect() fails. The NULL pointer is then dereferenced.
Also, the common error message referenced slave->data->phy_id,
which would be empty in the case of phy-handle. Instead, use the
name of the device_node as a useful identifier. And in the phy_id
case add the error code for completeness.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 9e42f71526 ("drivers: net: cpsw: add
phy-handle parsing") saved the "phy-handle" phandle into a new cpsw_priv
field. However, phy connections are per-slave, so the phy_node field should
be in cpsw_slave_data rather than cpsw_priv.
This would go unnoticed in a single emac configuration. But in dual_emac
mode, the last "phy-handle" property parsed for either slave would be used
by both of them, causing them both to refer to the same phy_device.
Fixes: 9e42f71526 ("drivers: net: cpsw: add phy-handle parsing")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Tested-by: Nicolas Chauvet <kwizart@gmail.com>
Tested-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configured in fixed link, the DaVinci emac driver sets the
priv->phydev to NULL and further ioctl calls to the phy_mii_ioctl()
causes the kernel to crash.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Fixes: 1bb6aa56bb ("net: davinci_emac: Add support for fixed-link PHY")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts were two cases of simple overlapping changes,
nothing serious.
In the UDP case, we need to add a hlist_add_tail_rcu()
to linux/rculist.h, because we've moved UDP socket handling
away from using nulls lists.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the DaVinci emac driver is removed and re-probed, the actual
pdev->dev.platform_data is populated with an unwanted valid pointer saved by
the previous davinci_emac_of_get_pdata() call, causing a kernel crash when
calling priv->int_disable() in emac_int_disable().
Unable to handle kernel paging request at virtual address c8622a80
...
[<c0426fb4>] (emac_int_disable) from [<c0427700>] (emac_dev_open+0x290/0x5f8)
[<c0427700>] (emac_dev_open) from [<c04c00ec>] (__dev_open+0xb8/0x120)
[<c04c00ec>] (__dev_open) from [<c04c0370>] (__dev_change_flags+0x88/0x14c)
[<c04c0370>] (__dev_change_flags) from [<c04c044c>] (dev_change_flags+0x18/0x48)
[<c04c044c>] (dev_change_flags) from [<c052bafc>] (devinet_ioctl+0x6b4/0x7ac)
[<c052bafc>] (devinet_ioctl) from [<c04a1428>] (sock_ioctl+0x1d8/0x2c0)
[<c04a1428>] (sock_ioctl) from [<c014f054>] (do_vfs_ioctl+0x41c/0x600)
[<c014f054>] (do_vfs_ioctl) from [<c014f2a4>] (SyS_ioctl+0x6c/0x7c)
[<c014f2a4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x1c)
Fixes: 42f59967a0 ("net: ethernet: davinci_emac: add OF support")
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid an Unbalanced pm_runtime_enable in the DaVinci
emac driver when the device is removed and re-probed, and a
pm_runtime_disable() call in davinci_emac_remove().
Actually, using unbind/bind on a TI DM8168 SoC gives :
$ echo 4a120000.ethernet > /sys/bus/platform/drivers/davinci_emac/unbind
net eth1: DaVinci EMAC: davinci_emac_remove()
$ echo 4a120000.ethernet > /sys/bus/platform/drivers/davinci_emac/bind
davinci_emac 4a120000.ethernet: Unbalanced pm_runtime_enable
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Fixes: 3ba9738134 ("net: ethernet: davinci_emac: add pm_runtime support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw_ndo_open() could try to access CPSW registers before
calling pm_runtime_get_sync(). This will trigger L3 error:
WARNING: CPU: 0 PID: 21 at drivers/bus/omap_l3_noc.c:147 l3_interrupt_handler+0x220/0x34c()
44000000.ocp:L3 Custom Error: MASTER M2 (64-bit) TARGET L4_FAST (Idle): Data Access in Supervisor mode during Functional access
and CPSW will stop functioning.
Hence, fix it by moving pm_runtime_get_sync() before the first access
to CPSW registers in cpsw_ndo_open().
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit cfe2556001
This can result in a "Unable to handle kernel paging request"
during boot. This was due to using an uninitialised struct member,
data->slaves.
Signed-off-by: Andrew Goodbody <andrew.goodbody@cambrionix.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The host_port field is constantly assigned to 0 and this value has
never changed (since time when cpsw driver was introduced. More over,
if this field will be assigned to non 0 value it will break current
driver functionality.
Hence, there are no reasons to continue maintaining this host_port
field and it can be removed, and the HOST_PORT_NUM and ALE_PORT_HOST
defines can be used instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ALE APIs expect to receive port masks as input values for arguments
port_mask, untag, reg_mcast, unreg_mcast. But there are few places in
code where port masks are passed left-shifted by cpsw_priv->host_port,
like below:
cpsw_ale_add_vlan(priv->ale, priv->data.default_vlan,
ALE_ALL_PORTS << priv->host_port,
ALE_ALL_PORTS << priv->host_port, 0, 0);
and cpsw is still working just because priv->host_port == 0
and has never ever been changed.
Hence, fix port_mask parameters in ALE APIs calls and drop
"<< priv->host_port" from all places where it's used to
shift valid port mask.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaa ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
While building keystone_defconfig of arm we are getting build failure
with the error:
drivers/net/ethernet/ti/netcp_core.c:1846:31: error: invalid type argument of '->' (have 'struct tc_to_netdev')
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
^
drivers/net/ethernet/ti/netcp_core.c:1851:35: error: invalid type argument of '->' (have 'struct tc_to_netdev')
(dev->real_num_tx_queues < tc->tc))
^
drivers/net/ethernet/ti/netcp_core.c:1855:8: error: invalid type argument of '->' (have 'struct tc_to_netdev')
if (tc->tc) {
^
drivers/net/ethernet/ti/netcp_core.c:1856:28: error: invalid type argument of '->' (have 'struct tc_to_netdev')
netdev_set_num_tc(dev, tc->tc);
^
drivers/net/ethernet/ti/netcp_core.c:1857:21: error: invalid type argument of '->' (have 'struct tc_to_netdev')
for (i = 0; i < tc->tc; i++)
^
drivers/net/ethernet/ti/netcp_core.c: At top level:
drivers/net/ethernet/ti/netcp_core.c:1879:2: warning: initialization from incompatible pointer type
.ndo_setup_tc = netcp_setup_tc,
^
The callback of ndo_setup_tc should be:
int (*ndo_setup_tc)(struct net_device *dev, u32 handle, __be16 protocol,
struct tc_to_netdev *tc);
But we missed marking the last argument as a pointer.
Fixes: 16e5cc6471 ("net: rework setup_tc ndo op to consume general tc operand")
CC: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
SW data field in descriptor can be used by software to hold private
data for the driver. As there are 4 words available for this purpose,
use separate macros to place it or retrieve the same to/from
descriptors. Also do type cast of data types accordingly.
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the pad to sw_data as per description of this field in the hardware
spec(refer sprugr9 from www.ti.com). Latest version of the document is
at http://www.ti.com/lit/ug/sprugr9h/sprugr9h.pdf and section 3.1
Host Packet Descriptor describes this field.
Define and use a constant for the size of sw_data field similar to
other fields in the struct for desc and document the sw_data field
in the header. As the sw_data is not touched by hw, it's type can be
changed to u32.
Rename the helpers to match with the updated dma desc field sw_data.
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: Arnd Bergmann <arnd@arndb.de>
CC: Grygorii Strashko <grygorii.strashko@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 8990777914 ("netcp: try to reduce type confusion in
descriptors") introduces a regression in Kernel 4.5-rc1 and it breaks
get/set_pad_info() functionality.
The TI NETCP driver uses pad0 and pad1 fields of knav_dma_desc to
store DMA/MEM buffer pointer and buffer size respectively. And in both
cases for Keystone 2 the pointer type size is 32 bit regardless of
LAPE enabled or not, because CONFIG_ARCH_DMA_ADDR_T_64BIT originally
is not expected to be defined.
Unfortunately, above commit changed buffer's pointers save/restore
code (get/set_pad_info()) and added intermediate conversation to u64
which works incorrectly on 32bit Keystone 2 and causes TI NETCP driver
crash in RX/TX path due to "Unable to handle kernel NULL pointer"
exception. This issue was reported and discussed in [1].
Hence, fix it by partially reverting above commit and restoring
get/set_pad_info() functionality as it was before.
[1] https://www.mail-archive.com/netdev@vger.kernel.org/msg95361.html
Cc: Wingman Kwok <w-kwok2@ti.com>
Cc: Mugunthan V N <mugunthanvnm@ti.com>
CC: David Laight <David.Laight@ACULAB.COM>
CC: Arnd Bergmann <arnd@arndb.de>
Reported-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cpsw-phy-sel driver supports only MII, RMII, and RGMII PHY modes,
and silently handled any other values as if MII was specified. In a
case where the PHY mode was incorrectly specified, or a bug elsewhere,
there would be no indication of a problem. If MII was the correct mode,
then this will go unnoticed, otherwise the symptom will be a failure
to transmit/receive data over the RMII/RGMII link.
Add a dev_warn() to make this condition obvious and provide a
breadcrumb to follow.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David Rivshin <drivshin@allworx.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates setup_tc so we can pass additional parameters into
the ndo op in a generic way. To do this we provide structured union
and type flag.
This lets each classifier and qdisc provide its own set of attributes
without having to add new ndo ops or grow the signature of the
callback.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ndo_setup_tc() op was added to support drivers offloading tx
qdiscs however only support for mqprio was ever added. So we
only ever added support for passing the number of traffic classes
to the driver.
This patch generalizes the ndo_setup_tc op so that a handle can
be provided to indicate if the offload is for ingress or egress
or potentially even child qdiscs.
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The davinci_cpdma mixes up physical addresses as seen from the CPU
and DMA addresses as seen from a DMA master, since it can operate
on both normal memory or an on-chip buffer. If dma_addr_t is
different from phys_addr_t, this means we get a compile-time warning
about the type mismatch:
ethernet/ti/davinci_cpdma.c: In function 'cpdma_desc_pool_create':
ethernet/ti/davinci_cpdma.c:182:48: error: passing argument 3 of 'dma_alloc_coherent' from incompatible pointer type [-Werror=incompatible-pointer-types]
pool->cpumap = dma_alloc_coherent(dev, size, &pool->phys,
In file included from ethernet/ti/davinci_cpdma.c:21:0:
dma-mapping.h:398:21: note: expected 'dma_addr_t * {aka long long unsigned int *}' but argument is of type 'phys_addr_t * {aka unsigned int *}'
static inline void *dma_alloc_coherent(struct device *dev, size_t size,
This slightly restructures the code so the address we use for
mapping RAM into a DMA address is always a dma_addr_t, avoiding
the warning. The code is correct even if both types are 32-bit
because the DMA master in this device only supports 32-bit addressing
anyway, independent of the types that are used.
We still assign this value to pool->phys, and that is wrong if
the driver is ever used with an IOMMU, but that value appears to
be never used, so there is no problem really. I've added a couple
of comments about where we do things that are slightly violating
the API.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7f854420fb ("phy: Add API for {un}registering an mdio device to
a bus") introduces an API to access mii_bus structures, but missed to
update the TI cpamc driver. This results in the following error message.
drivers/net/ethernet/ti/cpmac.c: In function 'cpmac_probe':
drivers/net/ethernet/ti/cpmac.c:1119:18: error:
'struct mii_bus' has no member named 'phy_map'
Fixes: 7f854420fb ("phy: Add API for {un}registering an mdio device to a bus")
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have drivers directly manipulate the mii_bus structure,
provide and API for registering and unregistering devices on an MDIO
bus, and performing lookups.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Have mdio_alloc() create the array of interrupt numbers, and
initialize it to POLLING. This is what most MDIO drivers want, so
allowing code to be removed from the drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many Ethernet drivers contain the same netdev_info() print statement
about the attached phy. Move it into the phy device code. Additionally
add a varargs function which can be used to append additional
information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Propagate the return value of platform_get_irq on failure.
A simplified version of the semantic match that finds the two cases where
no error code is returned at all is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
A cleanup patch I did was unfortunately wrong and introduced
multiple serious bugs in the netcp rx processing, as indicated
by these correct gcc warnings:
drivers/net/ethernet/ti/netcp_core.c:776:14: warning: 'buf_ptr' may be used uninitialized in this function [-Wuninitialized]
drivers/net/ethernet/ti/netcp_core.c:687:14: warning: 'ptr' may be used uninitialized in this function [-Wuninitialized]
I have checked the patch once more and found that a call to
get_pkt_info() accidentally got removed in netcp_free_rx_desc_chain,
and netcp_process_one_rx_packet no longer retrieved the correct
buffer length. This patch should fix all the known problems,
but I did not test on real hardware.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 8990777914 ("netcp: try to reduce type confusion in descriptors")
Signed-off-by: David S. Miller <davem@davemloft.net>
When a fixed-link sub-node exists in a slave node, the slave node
is also the PHY node. Since this is a separate use of the slave node,
of_node_get() should be used to increment the reference count.
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1f71e8c96f ("drivers: net: cpsw: Add
support for fixed-link PHY") did not parse the "phy-mode" property in
the case of a fixed-link PHY, leaving slave_data->phy_if with its default
of PHY_INTERFACE_MODE_NA(0). This later gets passed to phy_connect() in
cpsw_slave_open(), and eventually to cpsw_phy_sel() where it hits a default
case that configures the MAC for MII mode.
The user visible symptom is that while kernel log messages seem to indicate
that the interface is set up, there is no network communication. Eventually
a watchdog error occurs:
NETDEV WATCHDOG: eth0 (cpsw): transmit queue 0 timed out
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using more than one slave with ti cpsw and fixed phy the pd->phy_id
will be always zero, but slave_data->phy_id must be unique. pd->phy_id
means a "phy hardware id" whereas slave_data->phy_id means an "unique id",
so we should use pd->addr which has the same unique meaning.
Fixes: 1f71e8c96f ("drivers: net: cpsw: Add support for fixed-link PHY")
Signed-off-by: Pascal Speck <kernel@iktek.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The handling of epib and psdata remains a bit unclear in the driver,
as we access the same fields both as CPU-endian and through DMA
from the device.
Sparse warns about this:
ti/netcp_core.c:1147:21: warning: incorrect type in assignment (different base types)
ti/netcp_core.c:1147:21: expected unsigned int [usertype] *[assigned] epib
ti/netcp_core.c:1147:21: got restricted __le32 *<noident>
This uses __le32 types in a few places and uses __force where the code
looks fishy. The previous patch should really have produced the correct
behavior, but this second patch is needed to shut up the warnings about
it. Ideally it would be slightly rewritten to not need those casts,
but I don't dare do that without access to the hardware for proper
testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp driver produces tons of warnings when CONFIG_LPAE is enabled
on ARM:
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_tx_map_skb':
drivers/net/ethernet/ti/netcp_core.c:1084:13: warning: passing argument 1 of 'set_words' from incompatible pointer type [-Wincompatible-pointer-types]
This is the result of trying to pass a pointer to a dma_addr_t to
a function that expects a u32 pointer to copy that into a DMA descriptor.
Looking at that code in more detail to fix the warnings, I see multiple
related problems:
* The conversion functions are not endian-safe, as the DMA descriptors
are almost certainly fixed-endian, but the CPU is not.
* On 64-bit machines, passing a pointer through a u32 variable is a
bug, accessing an indirect pointer as a u32 pointer even more so.
* The handling of epib and psdata mixes native-endian and device-endian
data.
In this patch, I try to sort out the types for most accesses here,
adding le32_to_cpu/cpu_to_le32 where appropriate, and passing pointers
through two 32-bit words in the descriptor padding, to make it plausible
that the driver does the right thing if compiled for big-endian or
64-bit systems.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/renesas/ravb_main.c
kernel/bpf/syscall.c
net/ipv4/ipmr.c
All three conflicts were cases of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit b6745f6e4e ("drivers: net: cpsw: davinci_emac: move reading mac
id to common file") started using of_machine_is_compatible for detecting
type but missed at dm8148 causing Ethernet to stop working.
Let's fix the issue by adding handling for dm814x.
Cc: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Mugunthnan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netif_tx_napi_add() is a variant of netif_napi_add()
It should be used by drivers that use a napi structure
to exclusively poll TX.
We do not want to add this kind of napi in napi_hash[] in following
patches, adding generic busy polling to all NAPI drivers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix null deref in xt_TEE netfilter module, from Eric Dumazet.
2) Several spots need to get to the original listner for SYN-ACK
packets, most spots got this ok but some were not. Whilst covering
the remaining cases, create a helper to do this. From Eric Dumazet.
3) Missiing check of return value from alloc_netdev() in CAIF SPI code,
from Rasmus Villemoes.
4) Don't sleep while != TASK_RUNNING in macvtap, from Vlad Yasevich.
5) Use after free in mvneta driver, from Justin Maggard.
6) Fix race on dst->flags access in dst_release(), from Eric Dumazet.
7) Add missing ZLIB_INFLATE dependency for new qed driver. From Arnd
Bergmann.
8) Fix multicast getsockopt deadlock, from WANG Cong.
9) Fix deadlock in btusb, from Kuba Pawlak.
10) Some ipv6_add_dev() failure paths were not cleaning up the SNMP6
counter state. From Sabrina Dubroca.
11) Fix packet_bind() race, which can cause lost notifications, from
Francesco Ruggeri.
12) Fix MAC restoration in qlcnic driver during bonding mode changes,
from Jarod Wilson.
13) Revert bridging forward delay change which broke libvirt and other
userspace things, from Vlad Yasevich.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (65 commits)
Revert "bridge: Allow forward delay to be cfgd when STP enabled"
bpf_trace: Make dependent on PERF_EVENTS
qed: select ZLIB_INFLATE
net: fix a race in dst_release()
net: mvneta: Fix memory use after free.
net: Documentation: Fix default value tcp_limit_output_bytes
macvtap: Resolve possible __might_sleep warning in macvtap_do_read()
mvneta: add FIXED_PHY dependency
net: caif: check return value of alloc_netdev
net: hisilicon: NET_VENDOR_HISILICON should depend on HAS_DMA
drivers: net: xgene: fix RGMII 10/100Mb mode
netfilter: nft_meta: use skb_to_full_sk() helper
net_sched: em_meta: use skb_to_full_sk() helper
sched: cls_flow: use skb_to_full_sk() helper
netfilter: xt_owner: use skb_to_full_sk() helper
smack: use skb_to_full_sk() helper
net: add skb_to_full_sk() helper and use it in selinux_netlbl_skbuff_setsid()
bpf: doc: correct arch list for supported eBPF JIT
dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put"
bonding: fix panic on non-ARPHRD_ETHER enslave failure
...
Pull trivial updates from Jiri Kosina:
"Trivial stuff from trivial tree that can be trivially summed up as:
- treewide drop of spurious unlikely() before IS_ERR() from Viresh
Kumar
- cosmetic fixes (that don't really affect basic functionality of the
driver) for pktcdvd and bcache, from Julia Lawall and Petr Mladek
- various comment / printk fixes and updates all over the place"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
bcache: Really show state of work pending bit
hwmon: applesmc: fix comment typos
Kconfig: remove comment about scsi_wait_scan module
class_find_device: fix reference to argument "match"
debugfs: document that debugfs_remove*() accepts NULL and error values
net: Drop unlikely before IS_ERR(_OR_NULL)
mm: Drop unlikely before IS_ERR(_OR_NULL)
fs: Drop unlikely before IS_ERR(_OR_NULL)
drivers: net: Drop unlikely before IS_ERR(_OR_NULL)
drivers: misc: Drop unlikely before IS_ERR(_OR_NULL)
UBI: Update comments to reflect UBI_METAONLY flag
pktcdvd: drop null test before destroy functions
Add support for a fixed-link devicetree sub-node in case the the
cpsw MAC is directly connected to a non-mdio PHY/device.
Signed-off-by: Markus Brunner <systemprogrammierung.brunner@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
for_each_child_of_node performs an of_node_get on each iteration, so
a break out of the loop requires an of_node_put.
A simplified version of the semantic patch that fixes this problem is as
follows (http://coccinelle.lip6.fr):
// <smpl>
@@
local idexpression r.n;
expression r,e;
@@
for_each_child_of_node(r,n) {
...
(
of_node_put(n);
|
e = n
|
+ of_node_put(n);
? break;
)
...
}
... when != n
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv6/xfrm6_output.c
net/openvswitch/flow_netlink.c
net/openvswitch/vport-gre.c
net/openvswitch/vport-vxlan.c
net/openvswitch/vport.c
net/openvswitch/vport.h
The openvswitch conflicts were overlapping changes. One was
the egress tunnel info fix in 'net' and the other was the
vport ->send() op simplification in 'net-next'.
The xfrm6_output.c conflicts was also a simplification
overlapping a bug fix.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reasons to probe cpsw from late_initcall level
and it's not recommended. Hence, use module_platform_driver()
to register and probe cpsw driver from module_init() level.
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
add the ability to parse "phy-handle". This
is needed for phys, which have a DT node, and
need to parse DT properties.
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many drivers initialize uselessly n_priv_flags, n_stats, testinfo_len,
eedump_len & regdump_len fields in their .get_drvinfo() ethtool op.
It's not necessary as these fields is filled in ethtool_get_drvinfo().
v2: removed unused variable
v3: removed another unused variable
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Kconfig currently controlling compilation of this code is:
drivers/net/ethernet/ti/Kconfig:config TI_CPSW_PHY_SEL
drivers/net/ethernet/ti/Kconfig: bool "TI CPSW Switch Phy sel Support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: netdev@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IS_ERR(_OR_NULL) already contain an 'unlikely' compiler flag and there
is no need to do that again from its callers. Drop it.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Conflicts:
net/ipv4/arp.c
The net/ipv4/arp.c conflict was one commit adding a new
local variable while another commit was deleting one.
Signed-off-by: David S. Miller <davem@davemloft.net>
In case the DaVinci Emac is directly connected to a
non-mdio PHY/device, it should be possible to provide
a fixed link configuration in the DT.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A deadlock trace is seen in netcp driver with lockup detector enabled.
The trace log is provided below for reference. This patch fixes the
bug by removing the usage of netcp_modules_lock within ndo_ops functions.
ndo_{open/close/ioctl)() is already called with rtnl_lock held. So there
is no need to hold another mutex for serialization across processes on
multiple cores. So remove use of netcp_modules_lock mutex from these
ndo ops functions.
ndo_set_rx_mode() shouldn't be using a mutex as it is called from atomic
context. In the case of ndo_set_rx_mode(), there can be call to this API
without rtnl_lock held from an atomic context. As the underlying modules
are expected to add address to a hardware table, it is to be protected
across concurrent updates and hence a spin lock is used to synchronize
the access. Same with ndo_vlan_rx_add_vid() & ndo_vlan_rx_kill_vid().
Probably the netcp_modules_lock is used to protect the module not being
removed as part of rmmod. Currently this is not fully implemented and
assumes the interface is brought down before doing rmmod of modules.
The support for rmmmod while interface is up is expected in a future
patch set when additional modules such as pa, qos are added. For now
all of the tests such as if up/down, reboot, iperf works fine with this
patch applied.
Deadlock trace seen with lockup detector enabled is shown below for
reference.
[ 16.863014] ======================================================
[ 16.869183] [ INFO: possible circular locking dependency detected ]
[ 16.875441] 4.1.6-01265-gfb1e101 #1 Tainted: G W
[ 16.881176] -------------------------------------------------------
[ 16.887432] ifconfig/1662 is trying to acquire lock:
[ 16.892386] (netcp_modules_lock){+.+.+.}, at: [<c03e8110>]
netcp_ndo_open+0x168/0x518
[ 16.900321]
[ 16.900321] but task is already holding lock:
[ 16.906144] (rtnl_mutex){+.+.+.}, at: [<c053a418>] devinet_ioctl+0xf8/0x7e4
[ 16.913206]
[ 16.913206] which lock already depends on the new lock.
[ 16.913206]
[ 16.921372]
[ 16.921372] the existing dependency chain (in reverse order) is:
[ 16.928844]
-> #1 (rtnl_mutex){+.+.+.}:
[ 16.932865] [<c06023f0>] mutex_lock_nested+0x68/0x4a8
[ 16.938521] [<c04c5758>] register_netdev+0xc/0x24
[ 16.943831] [<c03e65c0>] netcp_module_probe+0x214/0x2ec
[ 16.949660] [<c03e8a54>] netcp_register_module+0xd4/0x140
[ 16.955663] [<c089654c>] keystone_gbe_init+0x10/0x28
[ 16.961233] [<c000977c>] do_one_initcall+0xb8/0x1f8
[ 16.966714] [<c0867e04>] kernel_init_freeable+0x148/0x1e8
[ 16.972720] [<c05f9994>] kernel_init+0xc/0xe8
[ 16.977682] [<c0010038>] ret_from_fork+0x14/0x3c
[ 16.982905]
-> #0 (netcp_modules_lock){+.+.+.}:
[ 16.987619] [<c006eab0>] lock_acquire+0x118/0x320
[ 16.992928] [<c06023f0>] mutex_lock_nested+0x68/0x4a8
[ 16.998582] [<c03e8110>] netcp_ndo_open+0x168/0x518
[ 17.004064] [<c04c48f0>] __dev_open+0xa8/0x10c
[ 17.009112] [<c04c4b74>] __dev_change_flags+0x94/0x144
[ 17.014853] [<c04c4c3c>] dev_change_flags+0x18/0x48
[ 17.020334] [<c053a9fc>] devinet_ioctl+0x6dc/0x7e4
[ 17.025729] [<c04a59ec>] sock_ioctl+0x1d0/0x2a8
[ 17.030865] [<c0142844>] do_vfs_ioctl+0x41c/0x688
[ 17.036173] [<c0142ae4>] SyS_ioctl+0x34/0x5c
[ 17.041046] [<c000ff60>] ret_fast_syscall+0x0/0x54
[ 17.046441]
[ 17.046441] other info that might help us debug this:
[ 17.046441]
[ 17.054434] Possible unsafe locking scenario:
[ 17.054434]
[ 17.060343] CPU0 CPU1
[ 17.064862] ---- ----
[ 17.069381] lock(rtnl_mutex);
[ 17.072522] lock(netcp_modules_lock);
[ 17.078875] lock(rtnl_mutex);
[ 17.084532] lock(netcp_modules_lock);
[ 17.088366]
[ 17.088366] *** DEADLOCK ***
[ 17.088366]
[ 17.094279] 1 lock held by ifconfig/1662:
[ 17.098278] #0: (rtnl_mutex){+.+.+.}, at: [<c053a418>]
devinet_ioctl+0xf8/0x7e4
[ 17.105774]
[ 17.105774] stack backtrace:
[ 17.110124] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 17.118637] Hardware name: Keystone
[ 17.122123] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 17.129862] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 17.137079] [<c05ff450>] (dump_stack) from [<c0068e34>]
(print_circular_bug+0x210/0x330)
[ 17.145161] [<c0068e34>] (print_circular_bug) from [<c006ab7c>]
(validate_chain.isra.35+0xf98/0x13ac)
[ 17.154372] [<c006ab7c>] (validate_chain.isra.35) from [<c006da60>]
(__lock_acquire+0x52c/0xcc0)
[ 17.163149] [<c006da60>] (__lock_acquire) from [<c006eab0>]
(lock_acquire+0x118/0x320)
[ 17.171058] [<c006eab0>] (lock_acquire) from [<c06023f0>]
(mutex_lock_nested+0x68/0x4a8)
[ 17.179140] [<c06023f0>] (mutex_lock_nested) from [<c03e8110>]
(netcp_ndo_open+0x168/0x518)
[ 17.187484] [<c03e8110>] (netcp_ndo_open) from [<c04c48f0>]
(__dev_open+0xa8/0x10c)
[ 17.195133] [<c04c48f0>] (__dev_open) from [<c04c4b74>]
(__dev_change_flags+0x94/0x144)
[ 17.203129] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>]
(dev_change_flags+0x18/0x48)
[ 17.211560] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>]
(devinet_ioctl+0x6dc/0x7e4)
[ 17.219729] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>]
(sock_ioctl+0x1d0/0x2a8)
[ 17.227378] [<c04a59ec>] (sock_ioctl) from [<c0142844>]
(do_vfs_ioctl+0x41c/0x688)
[ 17.234939] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>]
(SyS_ioctl+0x34/0x5c)
[ 17.242242] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>]
(ret_fast_syscall+0x0/0x54)
[ 17.258855] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow
control off
[ 17.271282] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:616
[ 17.279712] in_atomic(): 1, irqs_disabled(): 0, pid: 1662, name: ifconfig
[ 17.286500] INFO: lockdep is turned off.
[ 17.290413] Preemption disabled at:[< (null)>] (null)
[ 17.295728]
[ 17.297214] CPU: 1 PID: 1662 Comm: ifconfig Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 17.305735] Hardware name: Keystone
[ 17.309223] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 17.316970] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 17.324194] [<c05ff450>] (dump_stack) from [<c06023b0>]
(mutex_lock_nested+0x28/0x4a8)
[ 17.332112] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>]
(netcp_set_rx_mode+0x160/0x210)
[ 17.340724] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>]
(dev_set_rx_mode+0x1c/0x28)
[ 17.348982] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>]
(__dev_open+0xc4/0x10c)
[ 17.356724] [<c04c490c>] (__dev_open) from [<c04c4b74>]
(__dev_change_flags+0x94/0x144)
[ 17.364729] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>]
(dev_change_flags+0x18/0x48)
[ 17.373166] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>]
(devinet_ioctl+0x6dc/0x7e4)
[ 17.381344] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>]
(sock_ioctl+0x1d0/0x2a8)
[ 17.388994] [<c04a59ec>] (sock_ioctl) from [<c0142844>]
(do_vfs_ioctl+0x41c/0x688)
[ 17.396563] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>]
(SyS_ioctl+0x34/0x5c)
[ 17.403873] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>]
(ret_fast_syscall+0x0/0x54)
[ 17.413772] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
udhcpc (v1.20.2) started
Sending discover...
[ 18.690666] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow
control off
Sending discover...
[ 22.250972] netcp-1.0 2620110.netcp eth0: Link is Up - 1Gbps/Full - flow
control off
[ 22.258721] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 22.265458] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:616
[ 22.273896] in_atomic(): 1, irqs_disabled(): 0, pid: 342, name: kworker/1:1
[ 22.280854] INFO: lockdep is turned off.
[ 22.284767] Preemption disabled at:[< (null)>] (null)
[ 22.290074]
[ 22.291568] CPU: 1 PID: 342 Comm: kworker/1:1 Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 22.300255] Hardware name: Keystone
[ 22.303750] Workqueue: ipv6_addrconf addrconf_dad_work
[ 22.308895] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 22.316643] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 22.323867] [<c05ff450>] (dump_stack) from [<c06023b0>]
(mutex_lock_nested+0x28/0x4a8)
[ 22.331786] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>]
(netcp_set_rx_mode+0x160/0x210)
[ 22.340394] [<c03e9840>] (netcp_set_rx_mode) from [<c04c9d18>]
(__dev_mc_add+0x54/0x68)
[ 22.348401] [<c04c9d18>] (__dev_mc_add) from [<c05ab358>]
(igmp6_group_added+0x168/0x1b4)
[ 22.356580] [<c05ab358>] (igmp6_group_added) from [<c05ad2cc>]
(ipv6_dev_mc_inc+0x4f0/0x5a8)
[ 22.365019] [<c05ad2cc>] (ipv6_dev_mc_inc) from [<c058f0d0>]
(addrconf_dad_work+0x21c/0x33c)
[ 22.373460] [<c058f0d0>] (addrconf_dad_work) from [<c0042850>]
(process_one_work+0x214/0x8d0)
[ 22.381986] [<c0042850>] (process_one_work) from [<c0042f54>]
(worker_thread+0x48/0x4bc)
[ 22.390071] [<c0042f54>] (worker_thread) from [<c004868c>]
(kthread+0xf0/0x108)
[ 22.397381] [<c004868c>] (kthread) from [<c0010038>]
Trace related to incorrect usage of mutex inside ndo_set_rx_mode
[ 24.086066] BUG: sleeping function called from invalid context at
kernel/locking/mutex.c:616
[ 24.094506] in_atomic(): 1, irqs_disabled(): 0, pid: 1682, name: ifconfig
[ 24.101291] INFO: lockdep is turned off.
[ 24.105203] Preemption disabled at:[< (null)>] (null)
[ 24.110511]
[ 24.112005] CPU: 2 PID: 1682 Comm: ifconfig Tainted: G W
4.1.6-01265-gfb1e101 #1
[ 24.120518] Hardware name: Keystone
[ 24.124018] [<c00178e4>] (unwind_backtrace) from [<c0013cbc>]
(show_stack+0x10/0x14)
[ 24.131772] [<c0013cbc>] (show_stack) from [<c05ff450>]
(dump_stack+0x84/0xc4)
[ 24.138989] [<c05ff450>] (dump_stack) from [<c06023b0>]
(mutex_lock_nested+0x28/0x4a8)
[ 24.146908] [<c06023b0>] (mutex_lock_nested) from [<c03e9840>]
(netcp_set_rx_mode+0x160/0x210)
[ 24.155523] [<c03e9840>] (netcp_set_rx_mode) from [<c04c483c>]
(dev_set_rx_mode+0x1c/0x28)
[ 24.163787] [<c04c483c>] (dev_set_rx_mode) from [<c04c490c>]
(__dev_open+0xc4/0x10c)
[ 24.171531] [<c04c490c>] (__dev_open) from [<c04c4b74>]
(__dev_change_flags+0x94/0x144)
[ 24.179528] [<c04c4b74>] (__dev_change_flags) from [<c04c4c3c>]
(dev_change_flags+0x18/0x48)
[ 24.187966] [<c04c4c3c>] (dev_change_flags) from [<c053a9fc>]
(devinet_ioctl+0x6dc/0x7e4)
[ 24.196145] [<c053a9fc>] (devinet_ioctl) from [<c04a59ec>]
(sock_ioctl+0x1d0/0x2a8)
[ 24.203803] [<c04a59ec>] (sock_ioctl) from [<c0142844>]
(do_vfs_ioctl+0x41c/0x688)
[ 24.211373] [<c0142844>] (do_vfs_ioctl) from [<c0142ae4>]
(SyS_ioctl+0x34/0x5c)
[ 24.218676] [<c0142ae4>] (SyS_ioctl) from [<c000ff60>]
(ret_fast_syscall+0x0/0x54)
[ 24.227156] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netcp_rxpool_refill() that refill descriptors and attached
buffers to fdq while interrupt is enabled as part of NAPI poll. Doing
it while interrupt is disabled could be beneficial as hardware will
not be starved when CPU is busy with processing interrupt.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently netcp_module_probe() doesn't check the return value of
of_parse_phandle() that points to the interface data for the
module and then pass the node ptr to the module which is incorrect.
Check for return value and free the intf_modpriv if there is error.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, if netcp_allocate_rx_buf() fails due no descriptors
in the rx free descriptor queue, inside the netcp_rxpool_refill() function
the iterative loop to fill buffers doesn't terminate right away. So modify
the netcp_allocate_rx_buf() to return an error code and use it break the
loop when there is error.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The netcp interface is not fully initialized before attach the module
to the interface. For example, the tx pipe/rx pipe is initialized
in ethss module as part of attach(). So until this is complete, the
interface can't be registered. So move registration of interface to
net device outside the current loop that attaches the modules to the
interface.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netcp_core is the first driver that will get initialized and the modules
(ethss, pa etc) will then get initialized. So the code at the end of
netcp_probe() that iterate over the modules is a dead code as the module
list will be always be empty. So remove this code.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On K2HK, sgmii module registers of slave 0 and 1 are mem
mapped to one contiguous block, while those of slave 2
and 3 are mapped to another contiguous block. However,
on K2E and K2L, sgmii module registers of all slaves are
mem mapped to one contiguous block. SGMII APIs expect
slave 0 sgmii base when API is invoked for slave 0 and 1,
and slave 2 sgmii base when invoked for other slaves.
Before this patch, slave 0 sgmii base is always passed to
sgmii API for K2E regardless which slave is the API invoked
for. This patch fixes the problem.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for reading mac address using syscon driver for
dra7 and am437x platforms
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Moving mac address reading from ethernet driver to common
file for better maintenance and for code reusable.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In DRA72x EVM, by default slave 1 is connected to the onboard
phy, but slave 2 pins are also muxed with video input module
which is controlled by pcf857x gpio and currently to select slave
0 to connect to phy gpio hogging is used, but with
omap2plus_defconfig the pcf857x gpio is built as module. So when
using NFS on DRA72x EVM, board doesn't boot as gpio hogging do
not set proper gpio state to connect slave 0 to phy as it is
built as module and you do not see any errors for not setting
gpio and just mentions dhcp reply not got.
To solve this issue, introducing "mode-gpios" in DT when gpio
based muxing is required. This will throw a warning when gpio
get fails and returns probe defer. When gpio-pcf857x module is
installed, cpsw probes again and ethernet becomes functional.
Verified this on DRA72x with pcf as module and ramdisk.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Propagate error code on failure.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per Am335x Errata [1] Advisory 1.0.9, The CPSW C0_TX_PEND and
C0_RX_PEND interrupt outputs provide a single transmit interrupt
that combines transmit channel interrupts TXPEND[7:0] and a
single receive interrupt that combines receive channel interrupts
RXPEND[7:0]. The TXPEND[0] and RXPEND[0] interrupt outputs are
connected to the ARM Cortex-A8 interrupt controller (INTC) rather
than the C0_TX_PEND and C0_RX_PEND interrupt outputs. So even
though CPSW interrupt is cleared by writing appropriate values to
EOI register the interrupt is not cleared in IRQ controller. So
interrupt is still pending and CPU is struck in ISR, the
workaround is to disable the interrupts in ARM irq controller.
[1] http://www.ti.com/lit/er/sprz360f/sprz360f.pdf
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/cavium/Kconfig
The cavium conflict was overlapping dependency
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior to this patch, rx buffer size for each rx queue
of an interface is configurable through dts bindings.
But for an interface, the first rx queue's rx buffer
size is always the usual MTU size (plus usual overhead)
and page size for the remaining rx queues (if they are
enabled by specifying a non-zero rx queue depth dts
binding of the corresponding interface). This patch
removes the rx buffer size configuration capability.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of processing tx events in isr adding separate napi for
tx which improves performance by ~180Mbps with
omap2plus_defconfig on DRA74x platform. Also cleaning up rx napis
by renaming to napi_rx for better understanding the code.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since interrupt is shared between the two ethernet interface and
in isr only one napi is scheduled at an instance so having two
napis doesn't make any difference. So making napi also as a
common resource for the dual ethernet interfaces.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW interrupts can be disabled by masking CPSW interrupts and
clearing interrupt by writing appropriate EOI. So removing all
disable_irq/enable_irq as discussed in [1]
[1] http://patchwork.ozlabs.org/patch/492741/
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/s390/net/bpf_jit_comp.c
drivers/net/ethernet/ti/netcp_ethss.c
net/bridge/br_multicast.c
net/ipv4/ip_fragment.c
All four conflicts were cases of simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch clean up error handle code to use goto label properly. In some
cases, the code unnecessarily use goto instead of just returning the error
code. Code also make explicit calls to devm_* APIs on error which is
not necessary. In the gbe_remove() also it makes similar calls which is
also unnecessary.
Also fix few checkpatch warnings
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code seems to assume a null is returned when the list is empty
from first_sec_slave() to break the loop which is incorrect. Fix the
code by using list_empty().
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently if user do rmmod keystone_netcp.ko following warning is
seen :-
[ 59.035891] ------------[ cut here ]------------
[ 59.040535] WARNING: CPU: 2 PID: 1619 at drivers/net/ethernet/ti/
netcp_core.c:2127 netcp_remove)
This is because the interface list is not cleaned up in netcp_remove.
This patch fixes this. Also fix some checkpatch related warnings.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some of the K2E and K2L platforms, the two DWORDs in
efuse occupied by the pre-programmed mac address for
slave port 1 are swapped. To workaround this issue,
this patch adds a new define NETCP_EFUSE_ADDR_SWAP (2)
which signifies the occurrence of such swapping so that
the driver can take proper action. The flag can be
enabled in the corresponding netcp interface dts binding
as efuse-mac = <2> under the corresponding netcp
interface node.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch asserts SGMII RTRESET, i.e. resetting the SGMII Tx/Rx
logic, during network interface shutdown to avoid having the
hardware wedge when shutting down with high incoming traffic rates.
This is cleared (brought out of RTRESET) when the interface is
brought back up.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing statistics for the host
and slave ports of the CPSW on K2L and K2E platforms.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain applications it's beneficial to allow the CPSW h/w
stats counters to continue to increment even while the kernel
polls them. This patch implements this behavior for both 1G
and 10G ethernet subsystem modules.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Different Keystone2 platforms have different number and
layouts of hw statistics modules. This patch consolidates
the statistics processing of different Keystone2 platforms
for easy maintenance.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CPSW driver keeps internally some, but not all, of
the statistics available in the hw statistics modules. Furthermore,
some of the locations in the hw statistics modules are reserved and
contain no useful information. Prior to this patch, the driver
allocates memory of the size of the the whole hw statistics modules,
instead of the size of statistics-entries-interested-in (i.e. et_stats),
for internal storage. This patch fixes that.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes error in the setting of the hw statistics
module base for K2HK platform. In K2HK although there are
4 hw statistics modules, but only 2 are visible at a time.
Thus when setting up the pointers to the base of the
corresponding hw statistics modules, modules 0 and 2 should
point to one base, while modules 1 and 3 should point to the
other.
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug in which the timer routine synchronized
against the ethtool-triggered statistics updates with spin_lock_bh().
A timer function is itself a bottom-half, so this should be
spin_lock().
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
br_mdb.c conflict was a function call being removed to fix a bug in
'net' but whose signature was changed in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
With commit c03abd8463 ("net: ethernet: cpsw: don't requests IRQs
we don't use") common isr and napi are separated into separate tx isr
and rx isr/napi, but still in rx napi tx events are handled. So removing
the tx event handling in rx napi.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The keystone qmss will raise interrupt when packet arrive at the
receive queue. Only control available to avoid interrupt from happening
is to keep the free descriptor queue (FDQ) empty in the receive side.
So the filling of descriptors into the FDQ has to happen after
request_irq() call is made as part of knav_queue_enable_notify(). So
move the function netcp_rxpool_refill() after this call.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/bridge/br_mdb.c
Minor conflict in br_mdb.c, in 'net' we added a memset of the
on-stack 'ip' variable whereas in 'net-next' we assign a new
member 'vid'.
Signed-off-by: David S. Miller <davem@davemloft.net>
platform_driver does not need to set an owner because
platform_driver_register() will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 'c03abd84634d ("net: ethernet: cpsw: don't requests
IRQs we don't use")', common isr is split into tx and rx, but
in rx isr tx interrupt is also disabledi in cpsw_disable_irq().
So tx interrupts are not handled during rx interrupts and rx
napi completion and results in poor tx performance by 40Mbps.
Fixing by disabling only rx interrupt in rx isr.
Cc: Felipe Balbi <balbi@ti.com>
Cc: <stable@vger.kernel.org> # v4.0+
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_disable, already calls cpdma_ctlr_int_ctrl. There
is no need to disable the dma interrupts twice. This patch removes the
extra calls.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function, cpsw_intr_enable, already calls cpdma_ctlr_int_ctrl. There
is no need to enable the dma interrupts twice. This patch removes the
extra call.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
