If CONFIG_MAC80211_MESH is not set, cfg80211 will now allow advertising
interface combinations with NL80211_IFTYPE_MESH_POINT present.
Add appropriate ifdefs to avoid running into errors.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Maximum delay for waking up card is 50 ms. Because of typo in
counter, this delay goes to 500ms. This patch fixes the bug.
Cc: <stable@vger.kernel.org> # 3.2+
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On many different chips, important aspects of the MAC state are not
fully cleared by a warm reset. This can show up as tx/rx hangs, those
annoying "DMA failed to stop in 10 ms..." messages or other quirks.
On AR933x, the chip can occasionally get stuck in a way that only a
driver unload/reload or a reboot would bring it back to life.
With this patch, a full reset is issued when bringing the chip out of
FULL-SLEEP state (after idle), or if either Rx or Tx was not shut down
properly. This makes the DMA related error messages disappear completely
in my tests on AR933x, and the chip does not get stuck anymore.
Cc: stable@vger.kernel.org
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ath9k commit 2ef167557c
(ath9k: fix signal strength reporting issues) fixed an issue where the
reported per-frame signal strength reported to mac80211 was being
overwritten with an internal average. The same issue is also present
in ath9k_htc.
In addition to preventing the driver from overwriting the value, this
commit also ensures that the internal average (which is used for ANI)
only tracks beacons of the AP that we're connected to.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
RSSI is being stored internally as s8 in several places. The indication
of an unset RSSI value, ATH_RSSI_DUMMY_MARKER, was supposed to have been
set to 127, but ended up being set to 0x127 because of a code cleanup
mistake. This could lead to invalid signal strength values in a few
places.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The PIC was supposed to be a small signature appended to the
PhyDB data, but the signature isn't really static and thus
attempting to check it just causes the warnings spuriously
so remove them.
Signed-off-by: Dor Shaish <dor.shaish@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The wakeup packet in the status response is padded out
to a multiple of 4 bytes by the firmware for transfer
to the host, take that into account when checking the
length of the command.
Also, the reported wakeup packet includes the FCS but
the userspace API doesn't, so remove that. If it is a
data packet it is reported as an 802.3 packet but I
forgot to take into account and remove the encryption
head/tail, fix all of that as well.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When stations are removed while packets are in the queue,
we drain the queues first, and then remove the stations.
If this happens in AP mode while the interface is removed
the MAC context might be removed from the firmware before
we removed the station(s), resulting in a SYSASSERT 3421.
This is because we remove the MAC context from the FW in
stop_ap(), but only flush the station drain work later in
remove_interface().
Refactor the code a bit to have a common MAC context
removal preparation first to solve this.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FH hardware will always write back to the scratch field
in commands, even host commands not just TX commands, which
can overwrite parts of the command. This is problematic if
the command is re-used (with IWL_HCMD_DFL_NOCOPY) and can
cause calibration issues.
Address this problem by always putting at least the first
16 bytes into the buffer we also use for the command header
and therefore make the DMA engine write back into this.
For commands that are smaller than 16 bytes also always map
enough memory for the DMA engine to write back to.
Cc: stable@vger.kernel.org
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add the missing unlock before return from function brcmf_notify_vif_event()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Unload sequence for mwifiex PCIE driver is as follows:
1. Invoking cleanup module from kernel results into
pci_unregister_driver
2. Kernel invokes PCIE remove() handler which disconnects all
interfaces.
3. One step during disconnect is to clean PCIE TX rings.
During this we read txbd_rdptr from FW.
While loading driver next time, we see pci_enable_device()
results into system freeze. This may have happened because we
accessed PCI device after unregistering from bus driver.
Removing this ioread() operation resolves this bug.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the system suspends with mwifiex wifi powered on, and is then woken
by an ICMP ping packet, the ping response is discarded by the kernel
because the kernel incorrectly thinks there is no carrier.
I can't see any valid reason to want to report loss of carrier here,
so remove the offending code.
Fixes http://dev.laptop.org/ticket/12554
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When memory allocation using, kmalloc() fails, report appropriate error value.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes an instance of DMA buffer on stack(being passed to
usb_control_msg) for the wireless USB version of the Agere Orinoco card driver.
It also fixes the missing audit for the return value of firmware download
routine. Found using smatch.
Signed-off-by: Kumar Amit Mehta <gmate.amit@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rtlwifi allocates both setup_packet and data buffer of control message urb,
using shared kmalloc in _usbctrl_vendorreq_async_write. Structure used for
allocating is:
struct {
u8 data[254];
struct usb_ctrlrequest dr;
};
Because 'struct usb_ctrlrequest' is __packed, setup packet is unaligned and
DMA mapping of both 'data' and 'dr' confuses ARM/sunxi, leading to memory
corruptions and freezes.
Patch changes setup packet to be allocated separately.
[v2]:
- Use WARN_ON_ONCE instead of WARN_ON
Cc: <stable@vger.kernel.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For STA mode, collect VHT realated IEs from the Beacons or Probe
Responses and append similar VHT related IEs to association
requests.
For AP mode, get VHT related capability information and share it
with cfg80211 at the time of wiphy register. This information is
further used by cfg80211 and hostapd to start an AP with 802.11AC
support.
Currently only 8897 supports 802.11AC.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Nishant Sarmukadam <nishants@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Frank Huang <frankh@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They all can make one line.
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While unloading driver, we free all pending TX packets by flushing
TX ring. There is unhandled case for PCIE8897 while checking for
ring empty condition.
This patch adds the handling by calling mwifiex_pcie_txbd_empty().
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I removed a bit too much info last time.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Theoretically, the card may not enter CTKILL:
In case the timer that iwl_prepare_ct_kill_task is setting,
will expire before tt->state revert to its previous state.
Signed-off-by: Eytan Lifshitz <eytan.lifshitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The time event data structures are required also for P2P Device
interface.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The FW can differentiate between scans, according to the interface
type on which the scan was issues. Supply the interfaces type
information to the FW.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Occasionally, we would run into this warning:
iwlwifi 0000:02:00.0: U iwl_mvm_protect_session extend 0x2601: only 200 ms left
iwlwifi 0000:02:00.0: U iwl_mvm_remove_time_event Removing TE 0x2601
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0925, 60 bytes at 37[5]:9
iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Attempting to send sync command TIME_EVENT_CMD
iwlwifi 0000:02:00.0: U iwl_pcie_send_hcmd_sync Setting HCMD_ACTIVE for command TIME_EVENT_CMD
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command TIME_EVENT_CMD (#29), seq: 0x0926, 60 bytes at 38[6]:9
iwlwifi 0000:02:00.0: U iwl_mvm_time_event_response TIME_EVENT_CMD response - UID = 0x2601
iwlwifi 0000:02:00.0: I iwl_pcie_hcmd_complete Clearing HCMD_ACTIVE for command TIME_EVENT_CMD
iwlwifi 0000:02:00.0: U iwl_mvm_rx_time_event_notif Time event notification - UID = 0x2701 action 1
wlan0: associate with 00:0a:b8:55:a8:30 (try 2/3)
------------[ cut here ]------------
WARNING: at drivers/net/wireless/iwlwifi/mvm/time-event.c:269 iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]()
Modules linked in: [...]
Call Trace:
[<c1046e42>] warn_slowpath_common+0x72/0xa0
[<c1046e92>] warn_slowpath_null+0x22/0x30
[<f8cad913>] iwl_mvm_time_event_send_add+0x163/0x1a0 [iwlmvm]
[<f8cadead>] iwl_mvm_protect_session+0xcd/0x1c0 [iwlmvm]
[<f8ca2087>] iwl_mvm_mac_mgd_prepare_tx+0x67/0xa0 [iwlmvm]
[<f882a130>] ieee80211_sta_work+0x8f0/0x1070 [mac80211]
The reason is a problem with asynchronous vs. synchronous
commands, what happens here is the following:
* TE 0x2601 is removed, the TIME_EVENT_CMD for that is async
* a new TE (will be 0x2701) is created, the TIME_EVENT_CMD
for that is sync and also uses a notification wait for the
response (to avoid another race condition)
* the response for the TE 0x2601 removal comes from the
firmware, and is handled by the notification wait handler
that's really waiting for the second response, but can't
tell the difference, we therefore see the message
"TIME_EVENT_CMD response - UID = 0x2601" instead of
"TIME_EVENT_CMD response - UID = 0x2701".
Fix this issue by making the TE removal synchronous as well,
this means that we wait for the response to that command
first, before there's any chance of sending a new one.
Also, to detect such issues more easily in the future, add
a warning to the notification handler that detects them.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This is helpful for debugging the time event warning,
but also in general to see what's going on.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
All station commands must include a valid MAC ID,
the ID 0 is randomly valid in some cases, but we
must set the ID properly. Do that by passing the
right station and using its mac_id_n_color.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the firmware to know when DTIM beacons arrive
we have to program the DTIM time in TSF and system
time in the MAC context. Since mac80211 now tracks
the different times (on demand), this becomes easy.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The iwlwifi-next tree removed IEEE80211_HW_NEED_DTIM_BEFORE_ASSOC
while the mac80211-next tree removed
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Otherwise memory corruption occurs when using channel contexts (ATM when
param 'channel' > 1).
Signed-off-by: Karl Beldan <karl.beldan@rivierawaves.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Instead of modifying the HT SMPS capability field
for stations, track the SMPS mode explicitly in a
new field in the station struct and use it in the
drivers that care about it. This simplifies the
code using it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For VHT, many more bandwidth changes are possible. As a first
step, stop toggling the IEEE80211_HT_CAP_SUP_WIDTH_20_40 flag
in the HT capabilities and instead introduce a bandwidth field
indicating the currently usable bandwidth to transmit to the
station. Of course, make all drivers use it.
To achieve this, make ieee80211_ht_cap_ie_to_sta_ht_cap() get
the station as an argument, rather than the new capabilities,
so it can set up the new bandwidth field.
If the station is a VHT station and VHT bandwidth is in use,
also set the bandwidth accordingly.
Doing this allows us to get rid of the supports_40mhz flag as
the HT capabilities now reflect the true capability instead of
the current setting.
While at it, also fix ieee80211_ht_cap_ie_to_sta_ht_cap() to not
ignore HT cap overrides when MCS TX isn't supported (not that it
really happens...)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Remove the casts of the first argument of memset.
Neaten the style by using the sizeof the actual variable
being memset not the sizeof the type of variable.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These messages don't seem to be errors but notifications
that some attribute isn't quite right.
Don't mark them as errors.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch check output of pci_map_single() calls. I missed them on
my previous patch "iwlegacy: check for dma mapping errors", which
fixed only pci_map_page() calls.
To handle remaining possible dma mappings errors, we need to rearrange
ilXXXX_tx_skb() and il_enqueue_hcmd() functions.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Check output of dma_map_single functions which nowadays can fail (when
IOMMU is used). On write_beacon callbacks just print error, similar
like padding error is handled by rt2800_write_beacon.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for handling of PCIe sleep cookie depending
upon device properties. Some PCIe devices need sleep cookie probing
before accessing HW while some others don't. A new sleep_cookie
variable is defined as part of mwifiex_pcie_card_reg strcture and
set/reset as per device capability.
Sleep cookie is allocated/accessed/freed only when flag sleep_cookie
for this particular device is enabled.
Signed-off-by: Avinash Patil <patila@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As the number of drivers in the rtlwifi family has grown, the Kconfig
section for them has grown unwieldy. This change has two effects: (1)
Variable RTLWIFI_DEBUG is documented, and (2) the entries for the
drivers that depend on RTLWIFI are indented.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ccode is not NUL terminated. Presumably insisting on a terminator makes
brcms_c_country_valid() return false when it's not intended. ccode[2]
is sprom->leddc_on_time.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This partially reverts commit 44ba973699.
rate_control_rate_init assumes the rate_init member of
struct rate_control_ops is not NULL therefore not initializing it leads to
an oops as soon the driver succesfully associates to an AP.
The removal of rate_update from 44ba973699
is ok because rate_update is checked for NULL before being
called.
Signed-off-by: Catalin Iacob <iacobcatalin@gmail.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make the code more readable, and while at it also
add a missing "break" to avoid checking handlers
that cannot be used.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In managed mode, the HT/VHT capabilities aren't set when
the station is initially added, so update the station
when it is marked associated. In AP/GO mode, the station
will typically be added with full capabilities today,
but an upcoming change in hostapd may mean a similar
scenario as for managed mode, therefore do the update
unconditionally.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Now that mac80211 no longer starts the auth/assoc
timeouts when it transmits the frame, but only when
the frame status arrives, we no longer need to wait
for the session protection time event to start, we
can schedule it and enqueue the auth/assoc frame
right away. This reduces the amount of time we block
mac80211's workqueue.
Also, since now we no longer need different behavior
for session protection and P2P time events, refactor
the code to have just a common implementation.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If we haven't heard a beacon before we associate we can
still start the association process and set the MAC in
the firmware to associated only after having received a
beacon with DTIM period by reacting to the new change
flag (BSS_CHANGED_DTIM_PERIOD) from mac80211.
This reduces the association time in these cases.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If the AP/GO beacon changes, apply such a change
immediately, otherwise the AP/GO beacon can be
stale for a long time.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Query the wakeup reasons properly and then
report them to mac80211.
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
