The 1116r has code to set downshift. Refactor this into a helper, so
in future other marvell PHYs can use it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the init functions unilaterally enable set auto cross over
without using the helper. Make use of the helper, and respect the
phydev MDI configuration.
Clean up the #define used while setting polarity, and the other
functions of the bits in the register.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Turns out that MII_M1116R_CONTROL_REG_MAC is the same as
MII_88E1121_PHY_MSCR_REG. Refactor the code to set the RGMII delays
into a shared helper.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is repeated a few times. Refactor into a helped.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same code is repeated for different PHY versions. Put it into a
help and call when needed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than using an open coded equivalent, use the core
genphy_soft_reset() function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert spaces to tabs where appropriate, and fix up some otherwise
odd indentation.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver needs CONFIG_HAS_IOMEM and OF to be functional, but we still
let it build with COMPILE_TEST. This fixes the unmet dependency after
selecting MDIO_BCM_UNIMAC in commit mentioned below:
warning: (NET_DSA_BCM_SF2 && BCMGENET) selects MDIO_BCM_UNIMAC which has
unmet direct dependencies (NETDEVICES && MDIO_DEVICE && HAS_IOMEM &&
OF_MDIO)
Fixes: 9a4e796970 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current code, old and new PHY states are always logged.
>From now on, log only PHY state transitions.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Express the same logic more succinctly.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prefer logical operator that expresses the intent to bitwise one that
happens to give the same result.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames IP2ME-specific registers reg_ralue_v and
reg_ralue_tunnel_ptr to reg_ralue_ip2me_*.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The comments really belong to the individual enumerators. The comment
at the register should instead reference the enum.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bcmgenet_mii_init() has an error path which is strictly identical to the
unwinding that bcmgenet_mii_exit() does, so have bcmgenet_mii_init()
utilize bcmgenet_mii_exit() for that.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that we have fully migrated to the mdio-bcm-unimac driver, drop the
legacy MDIO bus code which did duplicate a fair amount of code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update the GENET driver to register an UniMAC MDIO bus controller for
the GENET internal MDIO bus, update the platform data code to attach the
PHY to the correct MDIO bus controller.
The Device Tree portion of the code is mostly left unmodified since the
lookup/binding is done via phandles and Device Tree nodes which are much
more flexible in locating and binding PHYs to their respective MDIO bus
controllers.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having the bcmgenet driver migrate over the
mdio-bcm-unimac driver, add a platform data structure which allows
passing integrating specific details like bus name, wait function to
complete MDIO operations and PHY mask.
We also define what the platform device name contract is by defining
UNIMAC_MDIO_DRV_NAME and moving it to the platform_data header.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to be stricly identical to what bcmgenet does, add a debug
print when a PHY workaround during bus->reset() is executed. Preliminary
change to moving bcmgenet towards mdio-bcm-unimac.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for having multiple GENET instances in a system (up to
3), make sure that we do include the bus instance number in the name of
the MDIO bus such that we change it from "unimac-mdio" to
"unimac-mdio-0" for instance.
So far, the only user of this driver is using Device Tree, which uses a
lookup/parenting based technique to map PHY devices to their respective
MDIO bus controllers, hence causing no additional changes.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Factor the code that does the busy polling on the MDIO_BUSY bit since we
will have different code-paths for for completion depending on whether
we are using interrupts or polling.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FEC Receive Control Register has a 14 bit field indicating the
longest frame that may be received. It is being set to 1522. Frames
longer than this are discarded, but counted as being in error.
When using DSA, frames from the switch has an additional header,
either 4 or 8 bytes if a Marvell switch is used. Thus a full MTU frame
of 1522 bytes received by the switch on a port becomes 1530 bytes when
passed to the host via the FEC interface.
Change the maximum receive size to 2048 - 64, where 64 is the maximum
rx_alignment applied on the receive buffer for AVB capable FEC
cores. Use this value also for the maximum receive buffer size. The
driver is already allocating a receive SKB of 2048 bytes, so this
change should not have any significant effects.
Tested on imx51, imx6, vf610.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the PHY is missing but expected, e.g. because of a typ0 in the dt
file, it is not possible to open the interface. ip link returns:
RTNETLINK answers: No such device
It is not very obvious what the problem is. Add a netdev_err() in this
case to make it easier to debug the issue.
[ 21.409385] fec 2188000.ethernet eth0: Unable to connect to phy
RTNETLINK answers: No such device
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Indirect access (PMI) to phy register only work in I2C mode. In
MDIO mode phy registers must be accessed directly. Introduced
struct lan9303_phy_ops to handle the two modes.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Preparing for the following fix of MDIO phy access:
Renamed functions that access PHY 1 and 2 indirectly through PMI
registers.
lan9303_port_phy_reg_wait_for_completion() to
lan9303_indirect_phy_wait_for_completion()
lan9303_port_phy_reg_read() to
lan9303_indirect_phy_read()
lan9303_port_phy_reg_write() to
lan9303_indirect_phy_write()
Also changed "val" parameter of lan9303_indirect_phy_write() to u16,
for clarity.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
lan9303_mdio_write()/_read() must multiply register number by 4 to get
offset.
Added some commments to the register definitions.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle that MDIO read with no response return 0xffff.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latency improvement related to NAPI conversion.
If all packets are processed from receive ring then need
to signal host.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If setting receive buffer fails, the error unwind would cause
kernel panic because it was not correctly doing RCU and NAPI
unwind. RCU'd pointer needs to be reset to NULL, and NAPI needs
to be disabled not deleted.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize how receive completion ring are managed.
* Allocate only as many slots as needed for all buffers from host
* Allocate before setting up sub channel for better error detection
* Don't need to keep copy of initial receive section message
* Precompute the watermark for when receive flushing is needed
* Replace division with conditional test
* Replace atomic per-device variable with per-channel check.
* Handle corner case where receive completion send
fails if ring buffer to host is full.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The internal API was passing struct hv_page_buffer **
when only simple struct hv_page_buffer * was necessary
for passing an array.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using %p to print pointer to packet meta-data doesn't give any
good info, and exposes kernel memory offsets.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes a bunch of fixups for issues reported by
lockdep.
* ethtool routines can assume RTNL
* send is done with RCU lock (and BH disable)
* avoid refetching internal device struct (netvsc)
instead pass it as a parameter.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump up driver version to match newer NIC firmware. Also update
nic_rx_stats (a struct common to host driver and firmware) by adding a new
field: fw_total_fwd_bytes.
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: Raghu Vatsavayi <raghu.vatsavayi@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes all checkpatch occurences of
"CHECK: spaces preferred around that '{+,-}' (ctx:VxV)"
in moxart_ether code.
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No space is necessary after a cast
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed coding style for null comparisons in moxart_ether driver
to be more consistent with the rest of the kernel coding style
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use 'unsigned int' instead of 'unsigned'
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove unnecessary braces from single-line if statement
This warning is found using checkpatch.pl
Signed-off-by: SZ Lin <sz.lin@moxa.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Rick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: Derek Chickles <derek.chickles@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit a390d1f379 ("phylib: convert state_queue work to
delayed_work"), the PHYLIB state machine was converted to use delayed
workqueues, yet some functions were still referencing the PHY library
timer in their comments, fix that and remove the now unused
linux/timer.h include.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
request_firmware() will fallback to user space helper and may cause
long delays when driver is loaded if udev doesn't correctly handle
FW requests. Since we never really made use of the user space
helper functionality switch to the simpler request_firmware_direct()
call. The side effect of this change is that no warning will be
printed when the FW image does not exists. To help users figure
out which FW file is missing print a info message when we request
each file.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
