Previously, a workaround was added to address a hardware bug in the
PCIm2PCI arbiter where a write by the driver of the Transmit/Receive
Descriptor Tail register could happen concurrently with a write of any
MAC CSR register by the Manageability Engine (ME) which could cause the
Tail register to have an incorrect value. The arbiter is supposed to
prevent the concurrent writes but there is a bug that can cause the Host
(driver) access to be acknowledged later than it should.
After further investigation, it was discovered that a driver write access
of any MAC CSR register after being idle for some time can be lost when
ME is accessing a MAC CSR register. When this happens, no further target
access is claimed by the MAC which could hang the system.
The workaround to check bit 24 in the FWSM register (set only when ME is
accessing a MAC CSR register) and delay for a limited amount of time until
it is cleared is now done for all driver writes of MAC CSR registers on
82579 with ME enabled. In the rare case when the driver is writing the
Tail register and ME is accessing any MAC CSR register for a duration
longer than the maximum delay, write the register and verify it has the
correct value before continuing, otherwise reset the device.
This patch also moves some pre-existing macros from the hardware-specific
header file to the more appropriate generic driver header file.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the adapter is closed while it is simultaneously going through a
reset, it can cause a null-pointer dereference when the two different code
paths simultaneously cleanup up the Tx/Rx resources.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_reload_nvm() to e1000e_reload_nvm_generic() to signify the
function is used for more than one MAC-family type, and set and use it as a
MAC ops function pointer to be consistent with the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_config_collision_dist() to
e1000e_config_collision_dist_generic() to signify the function is used for
more than one MAC-family type, and set and use it as a MAC ops function
pointer to be consistent with the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace e1000_check_reset_block() inline function with calls to the PHY ops
check_reset_block function pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace e1000_check_mng_mode() inline function with calls to the MAC ops
check_mng_mode function pointer.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_setup_link() to e1000e_setup_link_generic() to signify the
function is used for more than one MAC-family type. The 82571-family has
a custom setup_link function which also calls the generic function. The
ich8lan-family has a custom function which should just be called via the
function pointer. The 80003es2lan-family just uses the generic function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Rename e1000e_id_led_init() to e1000e_id_led_init_generic() to signify the
function is used for more than one MAC-family type. For the ich8lan MAC
family, some MACs use the generic function and others use the function
e1000_id_led_init_pchlan(). In all cases where e1000e_id_led_init() was
called directly, change to call the function pointer to be consistent with
the driver design.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This enables enabling/disabling reception of the Ethernet
FCS. This can be useful when sniffing packets.
For e1000e, enabling RXFCS can change the default
behaviour for how the NIC handles CRC. Disabling RXFCS
will take the NIC back to defaults, which can be configured
as part of the module options.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Internal stress testing with jumbo frames shows the reliability of ICH9 and
ICH10D devices is improved in certain corner cases by disabling the Early
Receive feature. To reduce the performance impact caused by disabling this
feature, the packet buffer sizes and relevant flow control settings are
modified accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the default hardware values for TIPG except for 80003es2lan(*). The
code that is removed in this patch is either unnecessarily writing the TIPG
register with the hardware default values for some devices (82571/2/3/4) or
writing the wrong value for others (ICH/PCH LOMs). The only change in
functionality is setting the correct default TIPG for the latter devices.
(*) The correct value for 80003es2lan is already set properly in
e1000_init_hw_80003es2lan() and e1000_cfg_kmrn_{10_100|1000}_80003es2lan(),
and the unused flag FLAG_TIPG_MEDIUM_FOR_80003ESLAN is removed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
For ring-specific functions, pass a pointer to the ring struct instead of a
pointer to the adapter struct.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The Tx/Rx head and tail registers and itr_register are always at known
addresses based on the __iomem address at which the PCI region (from BAR 0)
is mapped and known offsets within the region for each of these registers.
Store and use the full address rather than just the region offset to reduce
unnecessary address calculations. Also, change current u8 __iomem pointers
to void __iomem pointers.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Based on the original patch submitted my Michael Wang
<wangyun@linux.vnet.ibm.com>.
Descriptors may not be write-back while checking TX hang with flag
FLAG2_DMA_BURST on.
So when we detect hang, we just flush the descriptor and detect
again for once.
-v2 change 1 to true and 0 to false and remove extra ()
CC: Michael Wang <wangyun@linux.vnet.ibm.com>
CC: Flavio Leitner <fbl@redhat.com>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 67fd4fcb (e1000e: convert to stats64) added the ability to update
statistics more accurately and on-demand through the net_device_ops
.ndo_get_stats64 hook, but introduced a locking bug on 82577/8/9 when
linked at half-duplex (seen on kernels with CONFIG_DEBUG_ATOMIC_SLEEP=y and
CONFIG_PROVE_LOCKING=y). The commit introduced code paths that caused a
mutex to be locked in atomic contexts, e.g. an rcu_read_lock is held when
irqbalance reads the stats from /sys/class/net/ethX/statistics causing the
mutex to be locked to read the Phy half-duplex statistics registers.
The mutex was originally introduced to prevent concurrent accesses of
resources (the NVM and Phy) shared by the driver, firmware and hardware
a few years back when there was an issue with the NVM getting corrupted.
It was later split into two mutexes - one for the NVM and one for the Phy
when it was determined the NVM, unlike the Phy, should not be protected by
the software/firmware/hardware semaphore (arbitration of which is done in
part with the SWFLAG bit in the EXTCNF_CTRL register). This latter
semaphore should be sufficient to prevent resource contention of the Phy in
the driver (i.e. the mutex for Phy accesses is not needed), but to be sure
the mutex is replaced with an atomic bit flag which will warn if any
contention is possible.
Also add additional debug output to help determine when the sw/fw/hw
semaphore is owned by the firmware or hardware.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reported-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
The initial function and setup tables can be marked as constant.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Private rx_csum flags are now duplicate of netdev->features &
NETIF_F_RXCSUM. Remove those duplicates and use the net_device_ops
ndo_set_features. This is based on the original patch submitted by
Michał Mirosław <mirq-linux@rere.qmqm.pl>
Cc: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Some features currently not supported by the driver (e.g. RSS) require the
use of extended descriptors, but the driver is setup to only use legacy
descriptors in all modes except for when jumbo frames are enabled on some
parts. Convert the driver to always use extended descriptors in order to
enable the forthcoming support of these other features.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Moves the Intel wired LAN drivers into drivers/net/ethernet/intel/ and
the necessary Kconfig and Makefile changes.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
