Stop using the omap-specific implementations for gpio debouncing now that
gpiolib provides its own support.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass board specific data for MUSB (like interface_type,
mode etc) from board file by defining board
specific structure.
Each board file can define this structure based on
its requirement and pass this information to the
driver.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Gupta Ajay Kumar <ajay.gupta@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
mmc-twl4030.[ch] no longer has any dependency on twl4030
and should be renamed to reflect that.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Add new style mux init functions to omap3 board-*.c files
So far Beagle has been confirmed to be a CBB package,
and CM-T35 a CUS package.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Only mach-omap2 boards are currently using matrix_keypad. Allow
mach-omap1 boards to use the old style keypad.h without breaking.
Created against linux-2.6.32-rc5.
Compile tested with omap_3430sdp_defconfig and rx51_defconfig.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the low level debug UART io address as per this series.
The change is essential to have CONFIG_DEBUG_LL working.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most board-*.c files read configuration data from the bootloader in
their .init_machine() function. This needs to happen earlier, at some
point before omap2_init_common_hw() is called. This is because a
future patch will use the bootloader serial console port information
to enable the UART clocks earlier, immediately after omap2_clk_init().
This is in turn necessary since otherwise clock tree usecounts on
clocks like dpll4_m2x2_ck will be bogus, which can cause the
currently-active console UART clock to be disabled during boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some OMAP3 boards (Beagle Cx, Overo, RX51, Pandora) have 2
SDRAM parts connected to the SDRC.
This patch adds the following:
- add a new argument of type omap_sdrc_params struct*
to omap2_init_common_hw and omap2_sdrc_init for the 2nd CS params
- adapted the OMAP boards files to the new prototype of
omap2_init_common_hw
- add the SDRC 2nd CS registers offsets defines
- adapt the sram sleep code to configure the SDRC for the 2nd CS
Note: If the 2nd param to omap2_init_common_hw is NULL, then the
parameters are not programmed into the SDRC CS1 registers
Tested on 3430 SDP and Beagleboard rev C2 and B5, with
suspend/resume and frequency changes (cpufreq).
Signed-off-by: Jean Pihet <jpihet@mvista.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Based on an earlier patches by Stanley.Miao <stanley.miao@windriver.com>
and Nishant Kamat <nskamat@ti.com>.
Note that at the ads7846 support still needs support for vaux_control
for the touchscreen to work.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Based on an earlier patch by Stanley.Miao <stanley.miao@windriver.com>
with board-*.c changes split to avoid conflicts with other device updates.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
from 2.6.29, smc911x isn't maintained anymore. A new driver, smsc911x,
will replace it. so convert omap_ldp to use smsc911x driver.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Create a generic board-file for initializing usb
on omap2430 and omap3 boards.
Patch modified by Tony to build the module based on
CONFIG_USB_MUSB_SOC. Also merged in a patch adding
the nop xceiv from Ajay Kumar Gupta <ajay.gupta@ti.com>.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the defines to the associated board file and remove
the now unnecessary header file. Also rename
OMAP34XX_ETHR_START to LDP_ETHR_START.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The following patch enables SMC911x support to work on the OMAP LDP
board. Although the SMC911x driver will eventually be obsoleted, the
smsc911x patches are rather invasive for the -rc kernels.
Rather than risk destablising smsc911x, this simpler patch is preferred
to allow the network interface to work.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a given SDRAM clock rate, SDRAM chips require memory controllers
to use a specific set of timing minimums and maximums to transfer data
reliably. These parameters can be different for different memory chips
and can also potentially vary by board.
This patch adds the infrastructure for board-*.c files to pass this
timing data to the SDRAM controller init function. The timing data is
specified in an 'omap_sdrc_params' structure, in terms of SDRC
controller register values. An array of these structs, one per SDRC
target clock rate, is passed by the board-*.c file to
omap2_init_common_hw().
This patch does not define the values for different memory chips, nor
does it use the values for anything; those will come in subsequent patches.
linux-omap source commit is bc84ecfc795c2d1c5cda8da4127cf972f488a696.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix compile by removing remaining omap specific gpio
calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch
to do this with gpio_keys.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add low-level initialization for hsmmc controller. Merged into
this patch patch are various improvments and board support by
Grazvydas Ignotas and David Brownell.
Also change wire4 to be wires, as some newer controllers support
8 data lines.
Cc: Pierre Ossman <drzeus-mmc@drzeus.cx>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds minimal board support for the OMAP3430 LDP development platform.
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
