When hci_req_run() calls its provided complete function and one of the
HCI commands in the sequence fails, then provide the opcode of failing
command. In case of success HCI_OP_NOP is provided since all commands
completed.
This patch fixes the prototype of hci_req_complete_t and all its users.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The HCI_QUIRK_FIXUP_INQUIRY_MODE option allows to force Inquiry Result
with RSSI setting on controllers that do not indicate support for it,
but where it is known to be fully functional.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are some old Bluetooth modules from Silicon Wave and Broadcom
which support Inquiry Result with RSSI, but do not advertise it. The
core has quirks in the code to enable that inquiry mode. However as
it stands right now, that code is not even executed since entering
the function to determine which inquiry mode requires that the device
has the feature bit for Inquiry Result with RSSI set in the first
place. So this makes this dead code that hasn't work for a long
time.
In conclusion, just remove these extra quirks and simplify the setup
of the inquiry mode to be inline and with that a lot easier to read
and understand.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the Bluetooth controllers requires an unconfigured state (for
example when the BD_ADDR is missing), then it is important to try
to register the SMP channels when the controller transitions to the
configured state.
This also fixes an issue with the debugfs entires that are not present
for controllers that start out as unconfigured.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The AVM BlueFritz! USB controllers had a special handling in the
Bluetooth core when it comes to reading the supported commands.
Both drivers now set the HCI_QUIRK_BROKEN_LOCAL_COMMANDS and with
that it is no longer needed to look for vendor specific details.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller supports the LE Data Length Extension feature, the
default and maximum data length are read and now stored.
For backwards compatibility all values are initialized to the data
length values from Bluetooth 4.1 and earlier specifications.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller supports the new LE Data Length Extension feature
from Bluetooth 4.2 specification, enable the new events and read the
values for default and maxmimum data length supported by the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch moves the creation of the debugs files for LE controllers
into hci_debugfs.c file.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch moves the creation of the debugs files for BR/EDR controllers
into hci_debugfs.c file.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This patch moves the creation of the debugs files common for all
controllers into hci_debugfs.c file.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The debugfs file creation has been part of the core initialization
handling of controllers. With the introduction of Bluetooth 4.2 core
specification, the number of debugfs files is increasing even further.
To avoid cluttering the core controller handling, create a separate
file hci_debugfs.c to centralize all debugfs file creation. For now
leave the current files in the core, but in the future all debugfs
file creation will be moved.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Every BR/EDR/LE dual-mode controller requires to have a public address
and so far that has become the identity address and own address. The
only way to change that behavior was with a force_static_address
debugfs option.
However the host can actually disable the BR/EDR part of a dual-mode
controller and turn into a single mode LE controller. In that case
it makes perfect sense for a host to use a chosen static address
instead of the public address.
So if the host disables BR/EDR and configures a static address, then
that static address is used as identity address and own address. If
the host does not configure a static address, then the public address
is used as before.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This is a left-over from the patch that created hci_request.c. The
hci_update_page_scan functions should have been moved from hci_core.c
there.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch updates the Add Device mgmt command handler to use a
hci_request to wait for HCI command completion before notifying user
space of the mgmt command completion. To do this we need to add an extra
hci_request parameter to the hci_conn_params_set function. Since this
function has no other users besides mgmt.c it's moved there as a static
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Many places using hci_update_background_scan() try to synchronize
whatever they're doing with the help of hci_request callbacks. However,
since the hci_update_background_scan() function hasn't so far accepted a
hci_request pointer any commands triggered by it have been left out by
the synchronization. This patch modifies the API in a similar way as was
done for hci_update_page_scan, i.e. there's a variant that takes a
hci_request and another one that takes a hci_dev.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
None of the hci_request related things in net/bluetooth/hci_core.h are
needed anywhere outside of the core bluetooth module. This patch creates
a new net/bluetooth/hci_request.c file with its corresponding h-file and
moves the functionality there from hci_core.c and hci_core.h.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To keep the parameter list and its semantics clear it makes sense to
split the hci_update_page_scan function into two separate functions: one
taking a hci_dev and another taking a hci_request. The one taking a
hci_dev constructs its own hci_request and then calls the other
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch moves the mgmt_powered() notification earlier in the
hci_dev_do_close() function. This way the correct "not powered" error
gets passed to any pending mgmt commands. Without the patch the pending
commands would instead get a misleading "disconnected" response when
powering down the adapter.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Read Page Scan Activity and Read Page Scan Type commands are not
supported by all controllers. Move the execution of both commands
into the 3rd phase of the init procedure. And then check the bit
mask of supported commands before adding them to the init sequence.
With this re-ordering of the init sequence, the extra check for
AVM BlueFritz! controllers is no longer needed. They will report
that these two commands are not supported.
This fixes an issue with the Microsoft Corp. Wireless Transceiver
for Bluetooth 2.0 (ID 045e:009c).
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
mgmt_pending_remove() should be called with hci_dev_lock protection
and currently the rule to take dev lock is that all mgmt req_complete
functions should take dev lock. So this patch fixes the same in the
missing functions
Without this patch there is a chance of invalid memory access while
accessing the mgmt_pending list like below
bluetoothd: 392] [0] Backtrace:
bluetoothd: 392] [0] [<c04ec770>] (pending_eir_or_class+0x0/0x68) from [<c04f1830>] (add_uuid+0x34/0x1c4)
bluetoothd: 392] [0] [<c04f17fc>] (add_uuid+0x0/0x1c4) from [<c04f3cc4>] (mgmt_control+0x204/0x274)
bluetoothd: 392] [0] [<c04f3ac0>] (mgmt_control+0x0/0x274) from [<c04f609c>] (hci_sock_sendmsg+0x80/0x308)
bluetoothd: 392] [0] [<c04f601c>] (hci_sock_sendmsg+0x0/0x308) from [<c03d4d68>] (sock_aio_write+0x144/0x174)
bluetoothd: 392] [0] r8:00000000 r7 7c1be90 r6 7c1be18 r5:00000017 r4 a90ea80
bluetoothd: 392] [0] [<c03d4c24>] (sock_aio_write+0x0/0x174) from [<c00e2d4c>] (do_sync_write+0xb0/0xe0)
bluetoothd: 392] [0] [<c00e2c9c>] (do_sync_write+0x0/0xe0) from [<c00e371c>] (vfs_write+0x134/0x13c)
bluetoothd: 392] [0] r8:00000000 r7 7c1bf70 r6:beeca5c8 r5:00000017 r4 7c05900
bluetoothd: 392] [0] [<c00e35e8>] (vfs_write+0x0/0x13c) from [<c00e3910>] (sys_write+0x44/0x70)
bluetoothd: 392] [0] r8:00000000 r7:00000004 r6:00000017 r5:beeca5c8 r4 7c05900
bluetoothd: 392] [0] [<c00e38cc>] (sys_write+0x0/0x70) from [<c000e3c0>] (ret_fast_syscall+0x0/0x30)
bluetoothd: 392] [0] r9 7c1a000 r8:c000e568 r6:400b5f10 r5:403896d8 r4:beeca604
bluetoothd: 392] [0] Code: e28cc00c e152000c 0a00000f e3a00001 (e1d210b8)
bluetoothd: 392] [0] ---[ end trace 67b6ac67435864c4 ]---
bluetoothd: 392] [0] Kernel panic - not syncing: Fatal exception
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the host decides to use a non-resolvable private address, it
must ensure that this generated address does not match the public
address of the controller. Add an extra check to ensure this required
behavior.
In addition rename the variable from urpa to nrpa and fix all of the
comments in the code that use the term unresolvable instead of the
term non-resolvable as used in the Bluetooth specification.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the LE Read Local P-256 Public Key command is supported, then
enable its corresponding complete event. And when the LE Generate DHKey
command is supported, enable its corresponding complete event as well.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The new Extended Scanner Filter Policies feature has to be enabled by
selecting the correct filter policy for the scan parameters. This
patch does that when the controller has been enabled to use LE Privacy.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller supports the Extended Scanner Filter Policies, it
supports the LE Direct Advertising Report event. However by default
that event is blocked by the LE event mask. It is required to enable
it during controller setup.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Currently the discovery filter information are only cleared when the
actual discovery procedure has been stopped. To make sure that none
of the filters interfere with the background scanning and its device
found event reporting, clear the filter before starting background
scanning.
This means that the discovery filter is now cleared before either
Start Discovery, Start Service Discovery or background scanning.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In case of failure or when unplugging a controller, the allocated
memory for the UUID list of the discovery filter is not freed. Use
the newly introduced helper for reset the discovery filter and with
that also freeing existing memory.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The discovery filter allocates memory for its UUID list. So use
a helper function to free it and reset it to default states.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the upcoming addition of support for Start Service Discovery, the
discovery handling needs to filter on RSSI and UUID values. For that
they need to be stored in the discovery handling. This patch adds the
appropiate fields and also make sure they are reset when discovery
has been stopped.
Signed-off-by: Jakub Pawlowski <jpawlowski@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
We need to keep debug keys around at least until the point that they are
used - otherwise e.g. slave role behavior wouldn't work as there'd be no
key to be looked up. The correct behavior should therefore be to return
any stored keys but when we clean up the SMP context to remove the key
from the hdev list if keeping debug keys around hasn't been requestsed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be able to support OOB data for LE pairing we need to store the
address type of the remote device. This patch extends the relevant
functions and data types with a bdaddr_type variable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
There's no need to duplicate code for the 192 vs 192+256 variants of the
OOB data functions. This is also helpful to pave the way to support LE
SC OOB data where only 256 bit data is provided.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To make it possible to use LE SC functionality over BR/EDR with pre-4.1
controllers (that do not support BR/EDR SC links) it's useful to be able
to force LE SC operations even over a traditional SSP protected link.
This patch adds a debugfs switch to force a special debug flag which is
used to skip the checks for BR/EDR SC support.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We need to set the correct Link Key type based on the properties of the
LE SC pairing that it was derived from. If debug keys were used the type
should be a debug key, and the authenticated vs unauthenticated
information should be set on what kind of security level was reached.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that hci_find_ltk_by_addr is the only LTK lookup function there's no
need to keep the long name anymore. This patch shortens the function
name to simply hci_find_ltk.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that LTKs are always looked up based on bdaddr (with EDiv/Rand
checks done after a successful lookup) the hci_find_ltk function is not
needed anymore. This patch removes the function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LTKs derived from Secure Connections based pairing are symmetric, i.e.
they should match both master and slave role. This patch updates the LTK
lookup functions to ignore the desired role when dealing with SC LTKs.
Furthermore, with Secure Connections the EDiv and Rand values are not
used and should always be set to zero. This patch updates the LTK lookup
to first use the bdaddr as key and then do the necessary verifications
of EDiv and Rand based on whether the found LTK is for SC or not.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the HCI_SC_ENABLED flag will also be used for controllers without
BR/EDR Secure Connections support whenever we need to check specifically
for SC for BR/EDR we also need to check that the controller actually
supports it. This patch adds a convenience macro for check all the
necessary conditions and converts the places in the code that need it to
use it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch converts the hdev->link_keys list to be protected through
RCU, thereby eliminating the need to hold the hdev lock while accessing
the list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In __hci_cmd_sync_ev() and __hci_req_sync() if the hci_req_run() call
fails and we return from the functions we should ensure that the state
doesn't remain in TASK_INTERRUPTIBLE that we just set it to. This patch
fixes missing calls to set_current_state(TASK_RUNNING) in both places.
Reported-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Doing things like hci_conn_hash_flush() while holding the hdev lock is
risky since its synchronous pending work cancellation could cause the
L2CAP layer to try to reacquire the hdev lock. Right now there doesn't
seem to be any obvious places where this would for certain happen but
it's already enough to cause lockdep to start warning against the hdev
and the work struct locks being taken in the "wrong" order:
[ +0.000373] mgmt-tester/1603 is trying to acquire lock:
[ +0.000292] ((&conn->pending_rx_work)){+.+.+.}, at: [<c104266d>] flush_work+0x0/0x181
[ +0.000270]
but task is already holding lock:
[ +0.000000] (&hdev->lock){+.+.+.}, at: [<c13b9a80>] hci_dev_do_close+0x166/0x359
[ +0.000000]
which lock already depends on the new lock.
[ +0.000000]
the existing dependency chain (in reverse order) is:
[ +0.000000]
-> #1 (&hdev->lock){+.+.+.}:
[ +0.000000] [<c105ea8f>] lock_acquire+0xe3/0x156
[ +0.000000] [<c140c663>] mutex_lock_nested+0x54/0x375
[ +0.000000] [<c13d644b>] l2cap_recv_frame+0x293/0x1a9c
[ +0.000000] [<c13d7ca4>] process_pending_rx+0x50/0x5e
[ +0.000000] [<c1041a3f>] process_one_work+0x21c/0x436
[ +0.000000] [<c1041e3d>] worker_thread+0x1be/0x251
[ +0.000000] [<c1045a22>] kthread+0x94/0x99
[ +0.000000] [<c140f801>] ret_from_kernel_thread+0x21/0x30
[ +0.000000]
-> #0 ((&conn->pending_rx_work)){+.+.+.}:
[ +0.000000] [<c105e158>] __lock_acquire+0xa07/0xc89
[ +0.000000] [<c105ea8f>] lock_acquire+0xe3/0x156
[ +0.000000] [<c1042696>] flush_work+0x29/0x181
[ +0.000000] [<c1042864>] __cancel_work_timer+0x76/0x8f
[ +0.000000] [<c104288c>] cancel_work_sync+0xf/0x11
[ +0.000000] [<c13d4c18>] l2cap_conn_del+0x72/0x183
[ +0.000000] [<c13d8953>] l2cap_disconn_cfm+0x49/0x55
[ +0.000000] [<c13be37a>] hci_conn_hash_flush+0x7a/0xc3
[ +0.000000] [<c13b9af6>] hci_dev_do_close+0x1dc/0x359
[ +0.012038] [<c13bbe38>] hci_unregister_dev+0x6e/0x1a3
[ +0.000000] [<c12d33c1>] vhci_release+0x28/0x47
[ +0.000000] [<c10dd6a9>] __fput+0xd6/0x154
[ +0.000000] [<c10dd757>] ____fput+0xd/0xf
[ +0.000000] [<c1044bb2>] task_work_run+0x6b/0x8d
[ +0.000000] [<c1001bd2>] do_notify_resume+0x3c/0x3f
[ +0.000000] [<c140fa70>] work_notifysig+0x29/0x31
[ +0.000000]
other info that might help us debug this:
[ +0.000000] Possible unsafe locking scenario:
[ +0.000000] CPU0 CPU1
[ +0.000000] ---- ----
[ +0.000000] lock(&hdev->lock);
[ +0.000000] lock((&conn->pending_rx_work));
[ +0.000000] lock(&hdev->lock);
[ +0.000000] lock((&conn->pending_rx_work));
[ +0.000000]
*** DEADLOCK ***
Fully fixing this would require some quite heavy refactoring to change
how the hdev lock and hci_conn instances are handled together. A simpler
solution for now which this patch takes is to try ensure that the hdev
workqueue is empty before proceeding with the various cleanup calls,
including hci_conn_hash_flush().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The common short form of "randomizer" is "rand" in many places
(including the Bluetooth specification). The shorter version also makes
for easier to read code with less forced line breaks. This patch renames
all occurences of "randomizer" to "rand" in the Bluetooth subsystem
code.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch set converts the hdev->identity_resolving_keys list to use
RCU to eliminate the need to use hci_dev_lock/unlock.
An additional change that must be done is to remove use of
CRYPTO_ALG_ASYNC for the hdev-specific AES crypto context. The reason is
that this context is used for matching RPAs and the loop that does the
matching is under the RCU read lock, i.e. is an atomic section which
cannot sleep.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch set converts the hdev->long_term_keys list to use RCU to
eliminate the need to use hci_dev_lock/unlock.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The debufs entry for the BR/EDR whitelist is confusing since there is
a controller debugfs entry with the name white_list and both are two
different things.
With the BR/EDR whitelist, the actual interface in use is the device
list and thus just include all values from the internal BR/EDR whitelist
in the device_list debugfs entry.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some Bluetooth drivers require to reset the upper stack. To avoid having
all drivers send HCI Hardware Error events, provide a generic function
to wrap the reset functionality.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
__hci_cmd_sync_ev(), __hci_req_sync() could miss wake_up_interrupt from
hci_req_sync_complete() because hci_cmd_work() workqueue and its response
could be completed before they are ready to get the signal through
add_wait_queue(), set_current_state(TASK_INTERRUPTIBLE).
Signed-off-by: Chan-yeol Park <chanyeol.park@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Use spin_lock_bh() as the code is called from softirq in networking subsystem.
This is needed to prevent deadlocks when 6lowpan link is in use.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hci_recv_fragment function is no longer used by any driver and thus
do not export it. In fact it is not even needed by the core and it can
be removed altogether.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth core already does processing of the HCI command header
and puts it together before sending it to the driver. It is not really
efficient for the driver to look at the HCI command header again in
case it has to make certain decisions about certain commands. To make
this easier, just provide the opcode as part of the SKB control buffer
information. The extra information about the opcode is optional and
only provided for HCI commands.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_update_random_address will clear the RPA_EXPIRED flag and
proceed with setting a new one if the flag was set. However, the
set_random_addr() function that is called may choose to defer the update
to a later moment. In such a case the flag would incorrectly remain
unset unless set_random_addr() re-sets it. This patch fixes the issue.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The necessary steps for freeing connection paramaters have grown quite a
bit so we can simplify the code by factoring it out into its own
function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Wherever we keep hci_conn pointers around we should be using
hci_conn_get/put to ensure that they stay valid. This patch fixes
all places violating against the principle currently.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Recently the LE passive scanning and auto-connections feature was
introduced. It uses the hci_connect_le() API which returns a hci_conn
along with a reference count to that object. All previous users would
tie this returned reference to some existing object, such as an L2CAP
channel, and there'd be no leaked references this way. For
auto-connections however the reference was returned but not stored
anywhere, leaving established connections with one higher reference
count than they should have.
Instead of playing special tricks with hci_conn_hold/drop this patch
associates the returned reference from hci_connect_le() with the object
that in practice does own this reference, i.e. the hci_conn_params
struct that caused us to initiate a connection in the first place. Once
the connection is established or fails to establish this reference is
removed appropriately.
One extra thing needed is to call hci_pend_le_actions_clear() before
calling hci_conn_hash_flush() so that the reference is cleared before
the hci_conn objects are fully removed.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that we have per-adapter SMP data thanks to the root SMP L2CAP
channel we can take advantage of it and attach the AES crypto context
(only used for SMP) to it. This means that the smp_irk_matches() and
smp_generate_rpa() function can be converted to internally handle the
AES context.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As preparation for moving SMP to use l2cap_chan infrastructure we need
to move the (de)initialization functions to smp.c (where they'll
eventually need access to the local L2CAP channel callbacks).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
First of all, it's wasteful to initialize SMP if it's never going to be
used (e.g. on non-LE controllers). Second of all, when we move to use
l2cap_chan we need to know the real local address, meaning we must have
completed at least part of the HCI init. This patch moves the SMP
initialization to after the HCI init procedure and makes it depend on
whether the controller actually supports LE.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
As preparation for converting SMP to use the l2cap_chan infrastructure
refactor the (de)initialization into separate functions.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the AES crypto has not been initialized properly we should cleanly
return from the hci_find_irk_by_rpa() function. Right now this will not
happen in practice, but once (in subsequent patches) SMP init is moved
to after the HCI init procedure it is possible that the pointer is NULL.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If the AES crypto context is not available we cannot generate new RPAs.
We should therefore cleanly return an error from the function
responsible for updating the random address.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When we're not connectable and all whitelisted (BR/EDR) devices are
connected it doesn't make sense to keep page scan enabled. This patch
adds code to check for any disconnected whitelist devices and if there
are none take the appropriate action in the hci_update_page_scan()
function to disable page scan.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Similar to our hci_update_background_scan() function we can simplify a
lot of code by creating a unified helper function for doing page scan
updates. This patch adds such a function to hci_core.c and updates all
the relevant places to use it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
The HCI_PAIRABLE flag isn't actually controlling whether we're pairable
but whether we're bondable. Therefore, rename it accordingly.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With the Bluetooth 4.1 specification the Simultaneous LE and BR/EDR
controller option has been deprecated. It shall be set to zero and
ignored otherwise.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Expose the default values for minimum and maximum LE advertising
interval via debugfs for testing purposes.
Signed-off-by: Georg Lukas <georg@op-co.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Store the default values for minimum and maximum advertising interval
with all the other controller defaults. These vaules are sent to the
adapter whenever advertising is (re)enabled.
Signed-off-by: Georg Lukas <georg@op-co.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Devices using resolvable private addresses are required to provide
an identity resolving key. These devices can not be found using
the current controller white list support. This means if the kernel
knows about any devices with an identity resolving key, the white
list filtering must be disabled.
However so far the kernel kept identity resolving keys around even
for devices that are not using resolvable private addresses. The
notification to userspace clearly hints to not store the key and
so it is best to just remove the key from the kernel as well at
that point.
With this it easy now to detect when using the white list is
possible or when kernel side resolving of addresses is required.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth controller can use a white list filter when scanning
to avoid waking up the host for devices that are of no interest.
Devices marked as reporting, direct connection (incoming) or general
connection are now added to the controller white list. The update of
the white list happens just before enabling passive scanning.
In case the white list is full and can not hold all devices, the
white list is not used and the filter policy set to accept all
advertisements.
Using the white list for scanning allows for power saving with
controllers that do not handle the duplicate filtering correctly.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When adding remote devices to the kernel using the Add Device management
command, these devices are explicitly allowed to connect. This kind of
incoming connections are possible even when the controller itself is
not connectable.
For BR/EDR this distinction is pretty simple since there is only one
type of incoming connections. With LE this is not that simple anymore
since there are ADV_IND and ADV_DIRECT_IND advertising events.
The ADV_DIRECT_IND advertising events are send for incoming (slave
initiated) connections only. And this is the only thing the kernel
should allow when adding devices using action 0x01. This meaning
of incoming connections is coming from BR/EDR and needs to be
mapped to LE the same way.
Supporting the auto-connection of devices using ADV_IND advertising
events is an important feature as well. However it does not map to
incoming connections. So introduce a new action 0x02 that allows
the kernel to connect to devices using ADV_DIRECT_IND and in addition
ADV_IND advertising reports.
This difference is represented by the new HCI_AUTO_CONN_DIRECT value
for only connecting to ADV_DIRECT_IND. For connection to ADV_IND and
ADV_DIRECT_IND the old value HCI_AUTO_CONN_ALWAYS is used.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the Bluetooth controller supports Get MWS Transport Layer
Configuration command, then issue it during initialization.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the Bluetooth controller supports Read Local Supported Codecs
command, then issue it during initialization so that the list of
codecs is known.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's safer practice to use sizeof(*ptr) instead of sizeof(ptr_type) when
allocating memory in case the type changes. This also fixes the
following style of warnings from static analyzers:
CHECK: Prefer kzalloc(sizeof(*ie)...) over kzalloc(sizeof(struct inquiry_entry)...)
+ ie = kzalloc(sizeof(struct inquiry_entry), GFP_KERNEL);
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When HCI_CONNECTABLE is set the code has been enabling passive scanning
in order to be consistent with BR/EDR and accept connections from any
device doing directed advertising to us. However, some hardware
(particularly CSR) can get very noisy even when doing duplicates
filtering, making this feature waste resources.
Considering that the feature is for fairly corner-case use (devices
who'd use directed advertising would likely be in the whitelist anyway)
it's better to disable it for now. It may still be brought back later,
possibly with a better implementation (e.g. through improved scan
parameters).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The current "wait_on_bit" interface requires an 'action'
function to be provided which does the actual waiting.
There are over 20 such functions, many of them identical.
Most cases can be satisfied by one of just two functions, one
which uses io_schedule() and one which just uses schedule().
So:
Rename wait_on_bit and wait_on_bit_lock to
wait_on_bit_action and wait_on_bit_lock_action
to make it explicit that they need an action function.
Introduce new wait_on_bit{,_lock} and wait_on_bit{,_lock}_io
which are *not* given an action function but implicitly use
a standard one.
The decision to error-out if a signal is pending is now made
based on the 'mode' argument rather than being encoded in the action
function.
All instances of the old wait_on_bit and wait_on_bit_lock which
can use the new version have been changed accordingly and their
action functions have been discarded.
wait_on_bit{_lock} does not return any specific error code in the
event of a signal so the caller must check for non-zero and
interpolate their own error code as appropriate.
The wait_on_bit() call in __fscache_wait_on_invalidate() was
ambiguous as it specified TASK_UNINTERRUPTIBLE but used
fscache_wait_bit_interruptible as an action function.
David Howells confirms this should be uniformly
"uninterruptible"
The main remaining user of wait_on_bit{,_lock}_action is NFS
which needs to use a freezer-aware schedule() call.
A comment in fs/gfs2/glock.c notes that having multiple 'action'
functions is useful as they display differently in the 'wchan'
field of 'ps'. (and /proc/$PID/wchan).
As the new bit_wait{,_io} functions are tagged "__sched", they
will not show up at all, but something higher in the stack. So
the distinction will still be visible, only with different
function names (gds2_glock_wait versus gfs2_glock_dq_wait in the
gfs2/glock.c case).
Since first version of this patch (against 3.15) two new action
functions appeared, on in NFS and one in CIFS. CIFS also now
uses an action function that makes the same freezer aware
schedule call as NFS.
Signed-off-by: NeilBrown <neilb@suse.de>
Acked-by: David Howells <dhowells@redhat.com> (fscache, keys)
Acked-by: Steven Whitehouse <swhiteho@redhat.com> (gfs2)
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Steve French <sfrench@samba.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/20140707051603.28027.72349.stgit@notabene.brown
Signed-off-by: Ingo Molnar <mingo@kernel.org>
To make the code more understandable it makes sense to use the new HCI
defines for connection role instead of a "bool master" parameter. This
makes it immediately clear when looking at the function calls what the
last parameter is describing.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The allocation of inquiry cache entries is triggered as a result of
processing HCI events. Since the processing is done in the context
of a workqueue, there is no needed to allocate with GFP_ATOMIC in
that case. Switch it to GFP_KERNEL.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The support for LE encryption is optional and with that also the
LE Long Term Key Request event. If encryption is not supported, then
do not bother enabling this event.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The support for LE encryption is optional. When encryption is not
supported then also do not enable the encryption related events.
This moves the event mask setting to the third initialization
stage to ensure that the LE features are available.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Read LE Advertising Channel TX Power command is not mandatory for
a Bluetooth HCI controller only supporting receiption. Move the command
to the third stage of the controller initialization and only execute it
when support for it has been indicated.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The internals of the HCI request framework should not be leaking to
its users. Move them all into net/bluetooth/hci_core.c and provide
a simple hci_req_pending helper function for the one user outside
the framework.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller is brought up using legacy ioctl, the setting of
the HCI_PAIRABLE flag should happen then. Previously it was set during
enumeration and when retrieving device information.
This change also will not set the HCI_PAIRABLE flag when the controller
is used with the HCI User Channel operation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
During the initial setup phase, the controller is powered on and will
be powered off again if it is not used within the auto-off timeout.
Userspace using ioctl does not know about the difference between the
initial setup phase and a controller being present. It is a bad idea
to keep the controller powered by just looking at the device list or
device information. Instead just tell userspace that the controller
is still down.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the HCISETSCAN ioctl is the only non-mgmt user we care about for
setting the right discoverable state we can simply do the necessary
updates in the ioctl handler function instead. This then allows the
removal of the mgmt_discoverable function and should simplify that state
handling considerably.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
With subsequent patches we'll also need to update the discoverable
state. As the code grows bigger it's better to move this out from the
switch statement into its own function.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The mgmt_connectable function has been used to ensure that the right
actions to HCI_CONNECTABLE are taken when the HCI_Write_Scan_Enable
command is triggered by something else than mgmt. The only other user
that we really care about is the HCISETSCAN ioctl code, so we can
actually more simply perform the needed changes there instead.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The code for updating the HCI_CONNECTABLE flag was incorrectly using
test_and_set_bit instead of test_and_clear_bit when HCI_CONNECTABLE is
to be cleared.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When the white list is in use the code would not update the
HCI_CONNECTABLE flag if it gets changed through the ioctl code (e.g.
hciconfig hci0 pscan). Since the flag is important for properly
accepting incoming connections add code to fix it up if necessary and
emit a New Settings mgmt event.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
This patch extends the Add/Remove device commands by letting user space
pass BR/EDR addresses to them. The resulting entries get stored in a new
hdev->whitelist list. The idea is that we can now selectively accept
connections from devices in the list even though HCI_CONNECTABLE is not
set (the actual implementation of this is coming in a subsequent patch).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We already have several lists with struct bdaddr_list entries, and there
will be more in the future. Since the operations for adding, removing,
looking up and clearing entries in these lists are exactly the same it
doesn't make sense to define new functions for every single list. This
patch unifies the functions by passing the list_head to them instead of
a hci_dev pointer.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The Authenticated Payload Timeout Expired event is valid for
controllers with BR/EDR Secure Connections support, but also for
LE only controllers supporting LE Ping feature. When either of them
is available enable this event. Previous it was not enabled when
the controller was only supporting LE operation.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Now that we have a flag for tracking the real advertising state we
should use that to determine whether it's safe to update the random
address or not. The couple of places that were clearing the flag due to
a pending request need to be updated too.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For adapters that do not support LE and ones where LE hasn't been
enabled we shouldn't be trying to initiate background scanning. This
patch adds an extra check to the hci_update_background_scan() to ensure
that we bail out if HCI_LE_ENABLED is not set.
Since we do allow user space to feed the kernel with LE connection
parameters even when LE is not enabled we now need to also call
hci_update_background_scan() as soon as LE gets enabled so that scanning
gets started if necessary.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Enabling passive scanning always when we're connectable aligns us with
the BR/EDR page scanning. This is also consistent with the fact that the
code dealing with passive scanning results will actively try to connect
any direct advertising event when we're connectable.
This patch implements the feature by adding the connectable condition to
hci_update_background_scan() checks for starting scanning and by calling
hci_update_background_scan() whenever the connectable state changes.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have an active discovery going on we shouldn't do any changes to
LE scanning when hci_update_background_scan() is called (a call which
can happen for many different reasons). This patch fixes the issue by
returning from the function if the discovery state is anything else
except DISCOVERY_STOPPED.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In a subsequent patch the hci_update_background_scan() function will
depend on being able to know the current discovery state. For this to be
possible we need to set the new state early in the function. Since we
also need to check what the old state was this patch introduces an extra
variable for tracking it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The hdev->send driver callback is mandatory to be provided by a driver
before calling hci_register_dev. So enforce it and return EINVAL in
case it is not available.
All existing drivers are providing this callback anyway, so this is
just an extra sanity check.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The drivers are allowed to just return an error from hdev->send callback
and in that case the driver does not own the SKB. Which means that the
caller has to free the SKB.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the driver sets HCI_QUIRK_RAW_DEVICE, the controller will be set
as unconfigured. However running the unconfigured init procecure is
not useful since raw-only devices are not allowed to change its
configuration. This change skips the init procedure and just allows
user channel operation for this device.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When an unconfigured controllers reaches the configured state, it is
important to change the HCI_RAW flag. It indicates to userspace that
the controller is fully operational.
External configuration allows to bring the controller back into an
unconfigured state. In that case make sure HCI_RAW flag is set again.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This adds support for changing the public device address. This feature
is required by controllers that do not provide a public address and
have HCI_QUIRK_INVALID_BDADDR set.
Even if a controller has a public device address, this is useful when
an embedded system wants to use its own value. As long as the driver
provides the set_bdaddr callback, this allows changing the device
address before powering on the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the external configuration triggers the switch to a configured
controller, it means the setup needs to be run. Controllers that start
out unconfigured have only run limited set of HCI commands. This is
not enough for complete operation and thus run the setup procedure
before announcing the new controller index.
This introduces HCI_CONFIG flag as companion to HCI_SETUP flag. The
HCI_SETUP flag is only used once for the initial setup procedure. And
during that procedure hdev->setup driver callback is called. With the
new HCI_CONFIG the switch from unconfigured to configured state is
triggering the same setup procedure just without hdev->setup. This
is required since bringing a controller back to unconfigured state
from configured state is possible.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When calling Device Remove with BDADDR_ANY we should in a similar way
emit Device Removed events as we do when removing a single device. Since
we have to iterate the list and call device_removed() the dedicated
hci_conn_params_clear_enabled() is not really useful anymore. This patch
removes the helper function and does the event emission and list item
removal in a single loop.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For an unconfigured controller it is required to read at least the
local version information. If the set_bdaddr driver callback is
provideded, then also the local Bluetooth address will be read.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
For the quirks that are allow to be set during setup callback, the
check needs to be modified so that they are applied even if no
setup callback provided by the driver.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a controller requires external configuration, then setting this
quirk will allow indicating this.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When a Bluetooth controller does not have a valid public Bluetooth
address, then allow the driver to indicate this. If the quirk is
set, the Bluetooth core will switch to unconfigured state first
and will allow userspace to configure the address before starting
the full initialization of the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some circumstances we need to look up entries in pend_le_conns and in
other in pend_le_reports. This patch converts the existing lookup
function for pend_le_conns to something that can be used for both lists.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since there are no more users of this function we can simply go ahead
and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When powering off (hci_dev_do_close) we should clear both the
pend_le_reports and pend_le_conns types of entries. When powering on
respectively we should populate both lists. This patch converts the
hci_pend_le_conns_clear() function into hci_pend_le_actions_clear()
(which can now be static) and converts the restart_le_auto_conns()
function into restart_le_actions().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that there are no-longer any users of the hci_pend_le_conn_del()
function we can simply go ahead and remove it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since params->action is used for both the pend_le_conns and
pend_le_reports lists we can simplify the adding and deleting of the
lists considerably. For example, when deleting entries in most
situations we no-longer need to check the auto_connect value but can
directly proceed with calling list_del_init on param->action (which is
safe even if the entry is not part of any list).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When hci_conn_params_set() is called if the new auto_connect value is
the same as the old one we don't need to take any action. Simply return
success from the function in this case.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Now that pend_le_connections is a list of hci_conn_params entries we can
simply remove items from that list as we iterate through the global list
of le_conn_params. This also moves the responsibility of calling
hci_update_background_scan() to the functions that were previously
calling hci_pend_le_conns_clear(). The only user that's left for
hci_pend_le_conns_clear() is hci_dev_do_close() which anyway does not
need to call hci_update_background_scan().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To simplify manipulation and lookup of hci_conn_params entries of the
type HCI_AUTO_CONN_REPORT it makes sense to store them in their own
list. The new action list_head in hci_conn_params is used for this
purpose.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In preparation to store also HCI_AUTO_CONN_REPORT entries in a list it
makes sense to convert the existing pend_le_conn list head of
hci_conn_params into a more generically named "action". This makes sense
because a parameter entry will never participate in more than one action
list.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since we only store entries with identity addresses in the
le_conn_params and pend_le_conns lists we can avoid unnecessary lookups
by checking for an identity address before diving into the lists
themselves.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Since the connection parameters are always a basis for adding entries to
hdev->pend_le_conns (so far of type bdaddr_list) it's simpler and more
efficient to have the parameters themselves be the entries in the
pend_le_conns list. We do this by adding another list_head to the
hci_conn_params struct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
If we have one or more devices with HCI_AUTO_CONN_REPORT we should do
background scanning and emit mgmt_device_found events. This patch
modifies the hci_update_background_scan() function to extend the
conditions needed to trigger scanning, and adds the necessary code to
process_adv_report() to emit mgmt_device_found events.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
To be able to make the right choice of whether to start passive scanning
or to send out a mgmt_device_found event we need to know if there are
any devices in the le_conn_params list with the auto_connect value set
to HCI_AUTO_CONN_REPORT. This patch adds a counter for this kind of
devices.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a controller is in unconfigured state it is currently hidden
from the management interface. This change now announces the new
controller with an Unconfigured Index Added event and allows clients
to easily detect the controller.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
With the new unconfigured controller state it is possible to provide a
fully functional HCI transport, but disable the higher level operations
that would normally happen. This way userspace can try to configure the
controller before releases the unconfigured state.
The internal state is represented by HCI_UNCONFIGURED. This replaces the
HCI_QUIRK_RAW_DEVICE quirk as internal state representation. This is now
a real state and drivers can use the quirk to actually trigger this
state. In the future this will allow a more fine grained switching from
unconfigured state to configured state for controller inititialization.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are more places that can take advantage of is_identity_address()
besides hci_core.c. This patch moves the function to hci_core.h and
gives it the appropriate hci_ prefix.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
The 0x00 action value of mgmt means "scan and report" but do not
connect. This is different from HCI_AUTO_CONN_DISABLED so we need a new
value for it.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
In some circumstances we'll need to either clear only the enabled
parameters or only the disabled ones. This patch adds convenience
functions for this purpose.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
We'll soon have specific clear functions for clearing enabled or
disabled entries, so rename the function that removes everything to
clear_all().
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When allocating a new controller structure, then default to the internal
use value 0xffff first. Default to 0x0000 is a bad idea since that is
the manufacturer identifier of Ericsson Technology Licensing.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Some embedded controllers allow the programming of a public address
and this adds vendor support for supporting OEM confguration of such
addresses.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The Bluetooth 4.1 introduces a new LE meta event called "LE Remote
Connection Parameter Request" event. In order to the controller
sends this event to host, we should enable it during controller
initialization.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
During init2 phase, the LE local features have not be read yet so
we aren't able to rely on hdev->le_features to determine if the
controller supports the Connection Parameters Request Procedure.
For that reason, this patch moves LE event mask setting from init2
into init3 initialization phase.
The hdev->le_features mask will be checked by the next patch in order
to know if "LE Remote Connection Parameter Request Event" should be
enabled.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
For the Block/Unblock Device mgmt commands we should only emit the
Blocked/Unblocked events on any socket except for the one which received
the command. The code was previously incorrectly trying to look up a
non-existent pending command and thereby ending up not skipping the
command socket for the event.
We can simplify the code a lot by simply sending the event directly from
the command handler functions. We have the reference to the command
socket available there which makes it easy to pass to the mgmt_event
function for skipping.
The only notable side-effect of this is that the old blacklisting
ioctl's no-longer cause mgmt events to be emitted, however as user space
versions using these ioctl's are not mgmt-aware this is acceptable.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
When a new controller is initialized, but not powered from userspace
at the moment, the HCI_AUTO_OFF flag is still set. During this period,
userspace might program device for auto-connection, but never power
on the controller. In this case do not try to start background
scanning and leave it for later to be started.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Providing the flags parameter directly to mgmt_device_found function
makes the core simpler and more readable. With this it becomes a lot
easier to add new flags in the future.
This also changes hci_inquiry_cache_update to just return that flags
needed for mgmt_device_found since that is its only use for the two
return parameters anyway.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The connection interval parameter of hci_conn_params_set are always used
with the controller defaults. So just let hci_conn_params_add set the
controller default and not bother resetting them to controller defaults
every time the hci_conn_params_set is called.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_conn_params_add function provides the default allocation of
connection parameters. To avoid code duplication, use that code from
hci_conn_params_set to allocate or lookup parameter struct.
As a benefit the connection latency and supervision timeout parameters
are no longer reset to default when calling hci_conn_params_set.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When adding new connection parameters, it is useful to return either
the existing struct or the newly created one.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the controller is not active or in init/setup phase, do not
try to start or stop background scanning.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
In some cases it is useful to not overwrite connection parametes and
instead just create default ones if they don't exist. This function
does exactly that. hci_conn_params_add will allow to create new
default connection parameters. hci_conn_params_set will set the
values and also create new parameters if they don't exist.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller has a default value for the supervision timeout. Expose
this via debugfs for testing purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The controller has a default value for the connection latency. Expose
this via debugfs for testing purposes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Store the connection latency and supervision timeout default values
with all the other controller defaults. And when needed use them
for new connections.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Since the auto-connection handling has gained offical management
command support, remove the le_auto_conn debugfs entry.
For debugging purposes replace it a simple device_list debugfs
entry that allows listing of the current internal auto-connection
list used for passive scanning.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When the slave updates the connection parameters, store also the
connection latency and supervision timeout information in the
internal list of connection parameters for known devices.
Having these values available allowes the auto-connection
procedure to use the correct values from the beginning without
having to request an update on every connection establishment.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When calling hci_conn_params_clear function, it should update the
background scanning properly and not require a separate call to
update it.
For the case when the function is used during unregister of a
controller, an extra safe guard is but in place.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When hci_conn_params_clear is called, it is always followed by a
call to hci_pend_le_conns_clear. So instead of making this explicit
just make sure it is always called. This makes this function similar
on how hci_conn_params_add and hci_conn_params_del work.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The hci_pend_le_conn_* function should be placed before their actual
users. So move them before hci_conn_params_* functions.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The usage of non-resovlable private addresses for passive scanning is
a bad idea. Passive scanning will not send any SCAN_REQ and thus using
your identity address for passive scanning is not a privacy issue.
It is important to use the identity address during passive scanning
since that is the only way devices using direct advertising will be
reported correctly by the controller. This is overlooked detail in
the Bluetooth specification that current controllers are not able
to report direct advertising events for other than their current
address.
When remote peers are using direct advertising and scanning is done
with non-resolvable private address these devices will not be found.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Bluetooth controllers that are marked for raw-only usage can only be
used with user channel access. Any other operation should be rejected.
This simplifies the whole raw-only support since it now depends on
the fact that the controller is marked with HCI_QUIRK_RAW_DEVICE and
runtime raw access is restricted to user channel operation.
The kernel internal processing of HCI commands and events is designed
around the case that either the kernel has full control over the device
or that the device is driven from userspace. This now makes a clear
distinction between these two possible operation modes.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The ssp_debug_mode debugfs option for developers is no longer
needed. Support for using Secure Simple Pairing (SSP) debug
mode is exposed by the management interface now.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
