The new mode is "minimal-static" to be used when resources are more
limited to support a large number of VFs, for example The PF driver
will provision guaranteed minimum resources of 0. Each VF has no
guranteed resources until it tries to reserve resources during device
open.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The else-if branch and else branch set mac_ok to true similarly,
so combine the two into single else branch.
Also add comments to explain the two conditions, which
from Michael Chan and Vasundhara Volam.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code already forwards the VF MAC address to the PF, except
in one case. If the VF driver gets a valid MAC address from the firmware
during probe time, it will not forward the MAC address to the PF,
incorrectly assuming that the PF already knows the MAC address. This
causes "ip link show" to show zero VF MAC addresses for this case.
This assumption is not correct. Newer firmware remembers the VF MAC
address last used by the VF and provides it to the VF driver during
probe. So we need to always forward the VF MAC address to the PF.
The forwarded MAC address may now be the PF assigned MAC address and so we
need to make sure we approve it for this case.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For completeness and correctness, the VF driver needs to reserve these
RSS and L2 contexts.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware messages that are forwarded from PF to VFs are encapsulated.
The size of these encapsulated messages must not exceed the maximum
defined message size. Add appropriate checks to avoid oversize
messages. Firmware messages may be expanded in future specs and
this will provide some guardrails to avoid data corruption.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When firmware sends a DMA response to the driver, the last byte of the
message will be set to 1 to indicate that the whole response is valid.
The driver waits for the message to be valid before reading the message.
The firmware spec allows these response messages to increase in
length by adding new fields to the end of these messages. The
older spec's valid location may become a new field in a newer
spec. To guarantee compatibility, the driver should zero the valid
byte before interpreting the entire message so that any new fields not
implemented by the older spec will be read as zero.
For messages that are forwarded to VFs, we need to set the length
and re-instate the valid bit so the VF will see the valid response.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs are created, the current code subtracts the maximum VF
resources from the PF's pool. This under-estimates the resources
remaining in the PF pool. Instead, we should subtract the minimum
VF resources. The VF minimum resources are guaranteed to the VFs
and only these should be subtracted from the PF's pool.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trusted VFs are allowed to modify MAC address, even when PF
has assigned one.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Forward hwrm_func_vf_cfg command from VF to PF driver, to store
VF MAC address in PF's context. This will allow "ip link show"
to display all VF MAC addresses.
Maintain 2 locations of MAC address in VF info structure, one for
a PF assigned MAC and one for VF assigned MAC.
Display VF assigned MAC in "ip link show", only if PF assigned MAC is
not valid.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of the old method of evenly dividing the resources to the VFs,
use the new firmware API to specify min and max resources for each VF.
This way, there is more flexibility for each VF to allocate more or less
resources.
The min is the absolute minimum for each VF to function. The max is the
global resources minus the resources used by the PF. Each VF is
guaranteed the min. Up to max resources may be available for some VFs.
The PF driver can use one of 2 strategies specified in NVRAM to assign
the resources. The old legacy strategy of evenly dividing the resources
or the new flexible strategy.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for new firmware APIs to allocate hardware resources,
add a new struct bnxt_hw_resc to hold various min, max and reserved
resources. This new structure is common for PFs and VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In bnxt_sriov_enable(), we calculate to see if we have enough hardware
resources to enable the requested number of VFs. The logic to check
for minimum completion rings and statistics contexts is missing. Add
the required checks so that VF configuration won't fail.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a part of a patch-set that introduces support for
VF-reps in the bnxt_en driver. The driver registers eswitch mode
get/set methods with the devlink interface that allow a user to
enable SRIOV switchdev mode. When enabled, the driver registers
a VF-rep netdev object for each VF with the stack. This can
essentially bring the VFs unders the management perview of the
hypervisor and applications such as OVS.
The next patch in the series, adds the RX/TX routines and a slim
netdev implementation for the VF-reps.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VF representors and PTP are added features in the new firmware spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The .ndo_get_vf_config() is returning the wrong qos attribute. Fix
the code that checks and reports the qos and spoofchk attributes. The
BNXT_VF_QOS and BNXT_VF_LINK_UP flags should not be set by default
during init. time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Features added include WoL and selftest.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ulp_sriov_cfg callbacks when the number of VFs is changing. This
allows the RDMA driver to provision RDMA resources for the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Assign additional vnics to VFs whenever possible so that NTUPLE can be
supported on the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All available remaining completion rings not used by the PF should be
made available for the VFs so that there are enough rings in the VF to
support RDMA. The earlier workaround code of capping the rings by the
statistics context is removed.
When SRIOV is disabled, call a new function bnxt_restore_pf_fw_resources()
to restore FW resources. Later on we need to add some logic to account
for RDMA resources.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest interface has the latest DCB command structs. Get and store the
max number of lossless TCs the hardware can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the physical link is down and the VF virtual link is set to "enable",
the current code does not always work. If the link is down but the
cable is attached, the firmware returns LINK_SIGNAL instead of
NO_LINK. The current code is treating LINK_SIGNAL as link up.
The fix is to treat link as down when the link_status != LINK.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The VF link state can be changed via the 'ip link set' cmd.
Currently, the new link state does not take effect immediately.
The fix is for the PF to send a link change async event to the
designated VF after a VF link state change. This async event will
trigger the VF to update the link status.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF can setup a default VLAN for a VF. The default VLAN tag is
automatically inserted and stripped without the knowledge of the
stack running on the VF. The VF driver needs to know that default
VLAN is enabled as VLAN acceleration on the RX side is no longer
supported. Call netdev_update_features() to fix up the VLAN features
as necessary. Also, VLAN strip mode must be enabled to strip out
the default VLAN tag.
Only allow VF default VLAN to be set if the firmware spec is >= 1.2.1.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hypervisors (e.g. ESX) require the VF MAC address to be forwarded to
the PF for approval. In Linux PF, the call is not forwarded and the
firmware will simply check and approve the MAC address if the PF has not
previously administered a valid MAC address for this VF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new field names in API structs and stop using deprecated fields
auto_link_speed and auto_duplex in phy_cfg/phy_qcfg structs.
Update copyright year to 2016.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use appropriate firmware request header structure to prepare the
firmware messages. This avoids the unnecessary conversion of the
fields to 32-bit fields. Add appropriate endian conversion when
printing out the message fields in dmesg so that they appear correct
in the log.
Reported-by: Rob Swindell <swindell@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During remove_one() when SRIOV is enabled, the PF driver
should broadcast PF driver unload notification to all
VFs that are attached to VMs. Upon receiving the PF
driver unload notification, the VF driver should print
a warning message to message log. Certain operations on the
VF may not succeed after the PF has unloaded.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow the VF to setup its own MAC address if the PF has not administratively
set it for the VF. To do that, we should always store the MAC address
from the firmware. There are 2 cases:
1. The MAC address is valid. This MAC address is assigned by the PF and
it needs to override the current VF MAC address.
2. The MAC address is zero. The VF will use a random MAC address by default.
By storing this 0 MAC address in the VF structure, it will allow the VF
user to change the MAC address later using ndo_set_mac_address() when
it sees that the stored MAC address is 0.
v2: Expanded descriptions and added more comments.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This interface will be forward compatible with future changes.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer firmware will return the ring group resource when we call
hwrm_func_qcaps(). To be compatible with older firmware, use the
number of tx rings as the number of ring groups if the older firmware
returns 0. When determining how many rx rings we can support, take
the ring group resource in account as well in _bnxt_get_max_rings().
Divide and assign the ring groups to VFs.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to keep track of all resources, such as rx rings, tx rings,
cmpl rings, rss contexts, stats contexts, vnics, after we have
divided them for the VFs. Otherwise, subsequent ring changes on
the PF may not work correctly.
We adjust all max resources in struct bnxt_pf_info after they have been
assigned to the VFs. There is no need to keep the separate
max_pf_tx_rings and max_pf_rx_rings.
When SR-IOV is disabled, we call bnxt_hwrm_func_qcaps() to restore the
max resources for the PF.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Use local variable pf for repeated access to this pointer.
2. The 2nd argument num_vfs was unnecessarily declared as pointer to int.
This function doesn't change num_vfs so change the argument to int.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows multiple independent bits to be set for various states.
Subsequent patches to implement tx timeout reset will require this.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For PF, the bp->pf.mac_addr always holds the permanent MAC
addr assigned by the HW. For VF, the bp->vf.mac_addr always
holds the administrator assigned VF MAC addr. The random
generated VF MAC addr should never get stored to bp->vf.mac_addr.
This way, when the VF wants to change the MAC address, we can tell
if the adminstrator has already set it and disallow the VF from
changing it.
v2: Fix compile error if CONFIG_BNXT_SRIOV is not set.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of always calling pci_sriov_disable() in remove_one(),
the driver should detect whether VFs are currently assigned
to the VMs. If the VFs are active in VMs, then it should not
disable SRIOV as it is catastrophic to the VMs. Instead,
it just leaves the VFs alone and continues to unload the PF.
The user can then cleanup the VMs even after the PF driver
has been unloaded.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct bnxt_pf_info needs to be always defined. Move bnxt_update_vf_mac()
to bnxt_sriov.c and add some missing #ifdef CONFIG_BNXT_SRIOV.
Reported-by: Jim Hull <jim.hull@hpe.com>
Tested-by: Jim Hull <jim.hull@hpe.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Broadcom ethernet driver for the new family of NetXtreme-C/E
ethernet devices.
v5:
- Removed empty blank lines at end of files (noted by David Miller).
- Moved busy poll helper functions to bnxt.h to at least make the
.c file look less cluttered with #ifdef (noted by Stephen Hemminger).
v4:
- Broke up 2 long message strings with "\n" (suggested by John Linville)
- Constify an array of strings (suggested by Stephen Hemminger)
- Improve bnxt_vf_pciid() (suggested by Stephen Hemminger)
- Use PCI_VDEVICE() to populate pci_device_id table for more compact
source.
v3:
- Fixed 2 more sparse warnings.
- Removed some unused structures in .h files.
v2:
- Fixed all kbuild test robot reported warnings.
- Fixed many of the checkpatch.pl errors and warnings.
- Fixed the Kconfig description (noted by Dmitry Kravkov).
Acked-by: Eddie Wai <eddie.wai@broadcom.com>
Acked-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
