Changing a network device MTU can be a fairly frequent operation, and
failure to change the MTU is reflected to user-space properly, both by
an appropriate message as well as by looking at whether the device's MTU
matches the configuration.
Demote the prints to debug prints by using netdev_dbg(), making all
Intel wired LAN drivers consistent, since they used a mixture of PCI
device and network device prints before.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_PM_SLEEP is not defined compiler complain as follow:
CC [M] drivers/net/ethernet/intel/e1000e/netdev.o
drivers/net/ethernet/intel/e1000e/netdev.c:6302:12: warning: ‘e1000e_s0ix_entry_flow’ defined but not used [-Wunused-function]
static void e1000e_s0ix_entry_flow(struct e1000_adapter *adapter)
drivers/net/ethernet/intel/e1000e/netdev.c:6411:12: warning: ‘e1000e_s0ix_exit_flow’ defined but not used [-Wunused-function]
static void e1000e_s0ix_exit_flow(struct e1000_adapter *adapter)
LD [M] drivers/net/ethernet/intel/e1000e/e1000e.o
Add wrap to fix these warnings.
Reported-by: kbuild test robot <lpk@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add devices ID's for the next LOM generations that will be
available on the next Intel Client platform (Tiger Lake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Since we no longer check for __E1000_DOWN in e1000e_close we can drop the
spot where we were restoring the bit. This saves us a bit of unnecessary
complexity.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch is meant to address possible race conditions that can exist
between network configuration and power management. A similar issue was
fixed for igb in commit 9474933caf ("igb: close/suspend race in
netif_device_detach").
In addition it consolidates the code so that the PCI error handling code
will essentially perform the power management freeze on the device prior to
attempting a reset, and will thaw the device afterwards if that is what it
is planning to do. Otherwise when we call close on the interface it should
see it is detached and not attempt to call the logic to down the interface
and free the IRQs again.
From what I can tell the check that was adding the check for __E1000_DOWN
in e1000e_close was added when runtime power management was added. However
it should not be relevant for us as we perform a call to
pm_runtime_get_sync before we call e1000_down/free_irq so it should always
be back up before we call into this anyway.
Reported-by: Morumuri Srivalli <smorumu1@in.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: David Dai <zdai@linux.vnet.ibm.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Add devices ID's for the next LOM generations that will be
available on the next Intel Client platform (Comet Lake)
This patch provides the initial support for these devices
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement flow for S0ix support. Modern SoCs support S0ix low power
states during idle periods, which are sub-states of ACPI S0 that increase
power saving while supporting an instant-on experience for providing
lower latency that ACPI S0. The S0ix states shut off parts of the SoC
when they are not in use, while still maintaning optimal performance.
This patch add support for S0ix started from an Ice Lake platform.
Suggested-by: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Signed-off-by: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After hot plugging an 1Gbps Ethernet cable with 1Gbps link partner, the
MII_BMSR may report 10Mbps, renders the network rather slow.
The issue has much lower fail rate after commit 59653e6497 ("e1000e:
Make watchdog use delayed work"), which essentially introduces some
delay before running the watchdog task.
But there's still a chance that the hot plugging event and the queued
watchdog task gets run at the same time, then the original issue can be
observed once again.
So let's use mod_delayed_work() to add a deterministic 1 second delay
before running watchdog task, after an interrupt.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:
PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()
No functional changes intended.
Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This works around a possible stalled packet issue, which may occur due to
clock recovery from the PCH being too slow, when the LAN is transitioning
from K1 at 1G link speed.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204057
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of using to_pci_dev + pci_get_drvdata,
use dev_get_drvdata to make code simpler.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for unifying the skb_frag and bio_vec, use the fine
accessors which already exist and use skb_frag_t instead of
struct skb_frag_struct.
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to commit: 5d8682588605 ("[misc] mei: me: allow runtime
pm for platform with D0i3")
When disconnecting the cable and reconnecting it the NIC
enters DMoff state. This caused wrong link indication
and duplex mismatch. This bug is described in:
https://bugzilla.redhat.com/show_bug.cgi?id=1689436
Checking PCIm function state and performing PHY reset after a
timeout in watchdog task solves this issue.
Signed-off-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use delayed work instead of timers to run the watchdog of the e1000e
driver.
Simplify the code with one less middle function.
Signed-off-by: Detlev Casanova <detlev.casanova@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The e1000e driver is a great user of the usleep_range() API,
and has nice ranges that in principle help power management.
However the ranges that are used only during system startup are
very long (and can add easily 100 msec to the boot time) while
the power savings of such long ranges is irrelevant due to the
one-off, boot only, nature of these functions.
This patch shrinks some of the longest ranges to be shorter
(while still using a power friendly 1 msec range); this saves
100msec+ of boot time on my BDW NUCs
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Suggested-by: Tim Pepper <timothy.c.pepper@linux.intel.com>
Signed-off-by: Miguel Bernal Marin <miguel.bernal.marin@linux.intel.com>
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Driver does not want to keep packets in Tx queue when link is lost.
But present code only reset NIC to flush them, but does not prevent
queuing new packets. Moreover reset sequence itself could generate
new packets via netconsole and NIC falls into endless reset loop.
This patch wakes Tx queue only when NIC is ready to send packets.
This is proper fix for problem addressed by commit 0f9e980bf5
("e1000e: fix cyclic resets at link up with active tx").
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Suggested-by: Alexander Duyck <alexander.duyck@gmail.com>
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 0f9e980bf5.
That change cased false-positive warning about hardware hang:
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
e1000e 0000:00:1f.6 eth0: Detected Hardware Unit Hang:
TDH <0>
TDT <1>
next_to_use <1>
next_to_clean <0>
buffer_info[next_to_clean]:
time_stamp <fffba7a7>
next_to_watch <0>
jiffies <fffbb140>
next_to_watch.status <0>
MAC Status <40080080>
PHY Status <7949>
PHY 1000BASE-T Status <0>
PHY Extended Status <3000>
PCI Status <10>
e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
Besides warning everything works fine.
Original issue will be fixed property in following patch.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Reported-by: Joseph Yasi <joe.yasi@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203175
Tested-by: Joseph Yasi <joe.yasi@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Tested-by: Oleksandr Natalenko <oleksandr@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Pull networking updates from David Miller:
"Highlights:
1) Support AES128-CCM ciphers in kTLS, from Vakul Garg.
2) Add fib_sync_mem to control the amount of dirty memory we allow to
queue up between synchronize RCU calls, from David Ahern.
3) Make flow classifier more lockless, from Vlad Buslov.
4) Add PHY downshift support to aquantia driver, from Heiner
Kallweit.
5) Add SKB cache for TCP rx and tx, from Eric Dumazet. This reduces
contention on SLAB spinlocks in heavy RPC workloads.
6) Partial GSO offload support in XFRM, from Boris Pismenny.
7) Add fast link down support to ethtool, from Heiner Kallweit.
8) Use siphash for IP ID generator, from Eric Dumazet.
9) Pull nexthops even further out from ipv4/ipv6 routes and FIB
entries, from David Ahern.
10) Move skb->xmit_more into a per-cpu variable, from Florian
Westphal.
11) Improve eBPF verifier speed and increase maximum program size,
from Alexei Starovoitov.
12) Eliminate per-bucket spinlocks in rhashtable, and instead use bit
spinlocks. From Neil Brown.
13) Allow tunneling with GUE encap in ipvs, from Jacky Hu.
14) Improve link partner cap detection in generic PHY code, from
Heiner Kallweit.
15) Add layer 2 encap support to bpf_skb_adjust_room(), from Alan
Maguire.
16) Remove SKB list implementation assumptions in SCTP, your's truly.
17) Various cleanups, optimizations, and simplifications in r8169
driver. From Heiner Kallweit.
18) Add memory accounting on TX and RX path of SCTP, from Xin Long.
19) Switch PHY drivers over to use dynamic featue detection, from
Heiner Kallweit.
20) Support flow steering without masking in dpaa2-eth, from Ioana
Ciocoi.
21) Implement ndo_get_devlink_port in netdevsim driver, from Jiri
Pirko.
22) Increase the strict parsing of current and future netlink
attributes, also export such policies to userspace. From Johannes
Berg.
23) Allow DSA tag drivers to be modular, from Andrew Lunn.
24) Remove legacy DSA probing support, also from Andrew Lunn.
25) Allow ll_temac driver to be used on non-x86 platforms, from Esben
Haabendal.
26) Add a generic tracepoint for TX queue timeouts to ease debugging,
from Cong Wang.
27) More indirect call optimizations, from Paolo Abeni"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1763 commits)
cxgb4: Fix error path in cxgb4_init_module
net: phy: improve pause mode reporting in phy_print_status
dt-bindings: net: Fix a typo in the phy-mode list for ethernet bindings
net: macb: Change interrupt and napi enable order in open
net: ll_temac: Improve error message on error IRQ
net/sched: remove block pointer from common offload structure
net: ethernet: support of_get_mac_address new ERR_PTR error
net: usb: smsc: fix warning reported by kbuild test robot
staging: octeon-ethernet: Fix of_get_mac_address ERR_PTR check
net: dsa: support of_get_mac_address new ERR_PTR error
net: dsa: sja1105: Fix status initialization in sja1105_get_ethtool_stats
vrf: sit mtu should not be updated when vrf netdev is the link
net: dsa: Fix error cleanup path in dsa_init_module
l2tp: Fix possible NULL pointer dereference
taprio: add null check on sched_nest to avoid potential null pointer dereference
net: mvpp2: cls: fix less than zero check on a u32 variable
net_sched: sch_fq: handle non connected flows
net_sched: sch_fq: do not assume EDT packets are ordered
net: hns3: use devm_kcalloc when allocating desc_cb
net: hns3: some cleanup for struct hns3_enet_ring
...
mmiowb() is now implied by spin_unlock() on architectures that require
it, so there is no reason to call it from driver code. This patch was
generated using coccinelle:
@mmiowb@
@@
- mmiowb();
and invoked as:
$ for d in drivers include/linux/qed sound; do \
spatch --include-headers --sp-file mmiowb.cocci --dir $d --in-place; done
NOTE: mmiowb() has only ever guaranteed ordering in conjunction with
spin_unlock(). However, pairing each mmiowb() removal in this patch with
the corresponding call to spin_unlock() is not at all trivial, so there
is a small chance that this change may regress any drivers incorrectly
relying on mmiowb() to order MMIO writes between CPUs using lock-free
synchronisation. If you've ended up bisecting to this commit, you can
reintroduce the mmiowb() calls using wmb() instead, which should restore
the old behaviour on all architectures other than some esoteric ia64
systems.
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Will Deacon <will.deacon@arm.com>
There are two reasons for this.
First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.
Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().
We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.
Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.
skb->xmit_more is retained (but always 0) to not cause build breakage.
This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions. Remaining drivers are converted in the next patches.
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some new e1000e devices can only be woken up from D3 one time,
by plugging Ethernet cable. Subsequent cable plugging does set PME bit
correctly, but it still doesn't get woken up.
Since e1000e connects to the root complex directly, we rely on ACPI to
wake it up. In this case, the GPE from _PRW only works once and stops
working after that. Though it appears to be a platform bug, e1000e
maintainers confirmed that I219 does not support D3.
So disable runtime PM on CNP+ chips. We may need to disable earlier
generations if this bug also hit older platforms.
Bugzilla: https://bugzilla.kernel.org/attachment.cgi?id=280819
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
According to comments in <linux/netdevice.h> we should return either >0
or -errno from ->ndo_set_features() if changing dev->features by itself.
Return 1 in such places to notify netdev_update_features() about applied
changes in dev->features.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Provide precision hints to snprintf() since we know the destination
buffer size of the RX/TX ring names are IFNAMSIZ + 5 - 1. This fixes the
following warnings:
drivers/net/ethernet/intel/e1000e/netdev.c: In function
'e1000_request_msix':
drivers/net/ethernet/intel/e1000e/netdev.c:2109:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-rx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2107:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->rx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->rx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-rx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/intel/e1000e/netdev.c:2125:13: warning: 'snprintf'
output may be truncated before the last format character
[-Wformat-truncation=]
"%s-tx-0", netdev->name);
^
drivers/net/ethernet/intel/e1000e/netdev.c:2123:3: note: 'snprintf'
output between 6 and 21 bytes into a destination of size 20
snprintf(adapter->tx_ring->name,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
sizeof(adapter->tx_ring->name) - 1,
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
"%s-tx-0", netdev->name);
~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I'm seeing series of e1000e resets (sometimes endless) at system boot
if something generates tx traffic at this time. In my case this is
netconsole who sends message "e1000e 0000:02:00.0: Some CPU C-states
have been disabled in order to enable jumbo frames" from e1000e itself.
As result e1000_watchdog_task sees used tx buffer while carrier is off
and start this reset cycle again.
[ 17.794359] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 17.794714] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 22.936455] e1000e 0000:02:00.0 eth1: changing MTU from 1500 to 9000
[ 23.033336] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 26.102364] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
[ 27.174495] 8021q: 802.1Q VLAN Support v1.8
[ 27.174513] 8021q: adding VLAN 0 to HW filter on device eth1
[ 30.671724] cgroup: cgroup: disabling cgroup2 socket matching due to net_prio or net_cls activation
[ 30.898564] netpoll: netconsole: local port 6666
[ 30.898566] netpoll: netconsole: local IPv6 address 2a02:6b8:0:80b:beae:c5ff:fe28:23f8
[ 30.898567] netpoll: netconsole: interface 'eth1'
[ 30.898568] netpoll: netconsole: remote port 6666
[ 30.898568] netpoll: netconsole: remote IPv6 address 2a02:6b8:b000:605c:e61d:2dff:fe03:3790
[ 30.898569] netpoll: netconsole: remote ethernet address b0:a8:6e:f4:ff:c0
[ 30.917747] console [netcon0] enabled
[ 30.917749] netconsole: network logging started
[ 31.453353] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.185730] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.321840] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.465822] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.597423] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.745417] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 34.877356] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.005441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.157376] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.289362] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 35.417441] e1000e 0000:02:00.0: Some CPU C-states have been disabled in order to enable jumbo frames
[ 37.790342] e1000e: eth1 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
This patch flushes tx buffers only once when carrier is off
rather than at each watchdog iteration.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The change is based on the issue found by Kangjie Lu <kjlu@umn.edu> where
we not checking the return value of a register read/write which could result
in a NULL pointer dereference if the read/write fails.
Since we are only trying to disable the far-end loopback, if the read
and write of register fails, we do not want to bail out of the function.
We just want to log that it failed to disable and continue on.
CC: Sasha Neftin <sasha.neftin@intel.com>
CC: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
e1000e sets different WoL settings in system suspend callback and
runtime suspend callback.
The suspend direct complete optimization leaves e1000e in runtime
suspended state with wrong WoL setting during system suspend.
To fix this, we need to disable suspend direct complete optimization to
let e1000e always use suspend callback to set correct WoL during system
suspend.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
While reviewing code, I noticed that Eric Dumazet recommends that
drivers check the return code of napi_complete_done, and use that
to decide to enable interrupts or not when exiting poll. One of
the Intel drivers was already fixed (ixgbe).
Upon looking at the Intel drivers as a whole, we are handling our
polling and NAPI exit in a few different ways based on whether we
have multiqueue and whether we have Tx cleanup included. Several
drivers had the bug of exiting NAPI with return 0, which appears
to mess up the accounting in the stack.
Consolidate all the NAPI routines to do best known way of exiting
and to just mostly look like each other.
1) check return code of napi_complete_done to control interrupt enable
2) return the actual amount of work done.
3) return budget immediately if need NAPI poll again
Tested the changes on e1000e with a high interrupt rate set, and
it shows about an 8% reduction in the CPU utilization when busy
polling because we aren't re-enabling interrupts when we're about
to be polled.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems with some NICs supported by the e1000e driver a SYSTIM reading
may occasionally be few microseconds before the previous reading and if
enabled also pass e1000e_sanitize_systim() without reaching the maximum
number of rereads, even if the function is modified to check three
consecutive readings (i.e. it doesn't look like a double read error).
This causes an underflow in the timecounter and the PHC time jumps hours
ahead.
This was observed on 82574, I217 and I219. The fastest way to reproduce
it is to run a program that continuously calls the PTP_SYS_OFFSET ioctl
on the PHC.
Modify e1000e_phc_gettime() to use timecounter_cyc2time() instead of
timecounter_read() in order to allow non-monotonic SYSTIM readings and
prevent the PHC from jumping.
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-----BEGIN PGP SIGNATURE-----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=58I4
-----END PGP SIGNATURE-----
Merge tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
- Fix ASPM link_state teardown on removal (Lukas Wunner)
- Fix misleading _OSC ASPM message (Sinan Kaya)
- Make _OSC optional for PCI (Sinan Kaya)
- Don't initialize ASPM link state when ACPI_FADT_NO_ASPM is set
(Patrick Talbert)
- Remove x86 and arm64 node-local allocation for host bridge structures
(Punit Agrawal)
- Pay attention to device-specific _PXM node values (Jonathan Cameron)
- Support new Immediate Readiness bit (Felipe Balbi)
- Differentiate between pciehp surprise and safe removal (Lukas Wunner)
- Remove unnecessary pciehp includes (Lukas Wunner)
- Drop pciehp hotplug_slot_ops wrappers (Lukas Wunner)
- Tolerate PCIe Slot Presence Detect being hardwired to zero to
workaround broken hardware, e.g., the Wilocity switch/wireless device
(Lukas Wunner)
- Unify pciehp controller & slot structs (Lukas Wunner)
- Constify hotplug_slot_ops (Lukas Wunner)
- Drop hotplug_slot_info (Lukas Wunner)
- Embed hotplug_slot struct into users instead of allocating it
separately (Lukas Wunner)
- Initialize PCIe port service drivers directly instead of relying on
initcall ordering (Keith Busch)
- Restore PCI config state after a slot reset (Keith Busch)
- Save/restore DPC config state along with other PCI config state
(Keith Busch)
- Reference count devices during AER handling to avoid race issue with
concurrent hot removal (Keith Busch)
- If an Upstream Port reports ERR_FATAL, don't try to read the Port's
config space because it is probably unreachable (Keith Busch)
- During error handling, use slot-specific reset instead of secondary
bus reset to avoid link up/down issues on hotplug ports (Keith Busch)
- Restore previous AER/DPC handling that does not remove and
re-enumerate devices on ERR_FATAL (Keith Busch)
- Notify all drivers that may be affected by error recovery resets
(Keith Busch)
- Always generate error recovery uevents, even if a driver doesn't have
error callbacks (Keith Busch)
- Make PCIe link active reporting detection generic (Keith Busch)
- Support D3cold in PCIe hierarchies during system sleep and runtime,
including hotplug and Thunderbolt ports (Mika Westerberg)
- Handle hpmemsize/hpiosize kernel parameters uniformly, whether slots
are empty or occupied (Jon Derrick)
- Remove duplicated include from pci/pcie/err.c and unused variable
from cpqphp (YueHaibing)
- Remove driver pci_cleanup_aer_uncorrect_error_status() calls (Oza
Pawandeep)
- Uninline PCI bus accessors for better ftracing (Keith Busch)
- Remove unused AER Root Port .error_resume method (Keith Busch)
- Use kfifo in AER instead of a local version (Keith Busch)
- Use threaded IRQ in AER bottom half (Keith Busch)
- Use managed resources in AER core (Keith Busch)
- Reuse pcie_port_find_device() for AER injection (Keith Busch)
- Abstract AER interrupt handling to disconnect error injection (Keith
Busch)
- Refactor AER injection callbacks to simplify future improvments
(Keith Busch)
- Remove unused Netronome NFP32xx Device IDs (Jakub Kicinski)
- Use bitmap_zalloc() for dma_alias_mask (Andy Shevchenko)
- Add switch fall-through annotations (Gustavo A. R. Silva)
- Remove unused Switchtec quirk variable (Joshua Abraham)
- Fix pci.c kernel-doc warning (Randy Dunlap)
- Remove trivial PCI wrappers for DMA APIs (Christoph Hellwig)
- Add Intel GPU device IDs to spurious interrupt quirk (Bin Meng)
- Run Switchtec DMA aliasing quirk only on NTB endpoints to avoid
useless dmesg errors (Logan Gunthorpe)
- Update Switchtec NTB documentation (Wesley Yung)
- Remove redundant "default n" from Kconfig (Bartlomiej Zolnierkiewicz)
- Avoid panic when drivers enable MSI/MSI-X twice (Tonghao Zhang)
- Add PCI support for peer-to-peer DMA (Logan Gunthorpe)
- Add sysfs group for PCI peer-to-peer memory statistics (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA scatterlist mapping interface (Logan
Gunthorpe)
- Add PCI configfs/sysfs helpers for use by peer-to-peer users (Logan
Gunthorpe)
- Add PCI peer-to-peer DMA driver writer's documentation (Logan
Gunthorpe)
- Add block layer flag to indicate driver support for PCI peer-to-peer
DMA (Logan Gunthorpe)
- Map Infiniband scatterlists for peer-to-peer DMA if they contain P2P
memory (Logan Gunthorpe)
- Register nvme-pci CMB buffer as PCI peer-to-peer memory (Logan
Gunthorpe)
- Add nvme-pci support for PCI peer-to-peer memory in requests (Logan
Gunthorpe)
- Use PCI peer-to-peer memory in nvme (Stephen Bates, Steve Wise,
Christoph Hellwig, Logan Gunthorpe)
- Cache VF config space size to optimize enumeration of many VFs
(KarimAllah Ahmed)
- Remove unnecessary <linux/pci-ats.h> include (Bjorn Helgaas)
- Fix VMD AERSID quirk Device ID matching (Jon Derrick)
- Fix Cadence PHY handling during probe (Alan Douglas)
- Signal Cadence Endpoint interrupts via AXI region 0 instead of last
region (Alan Douglas)
- Write Cadence Endpoint MSI interrupts with 32 bits of data (Alan
Douglas)
- Remove redundant controller tests for "device_type == pci" (Rob
Herring)
- Document R-Car E3 (R8A77990) bindings (Tho Vu)
- Add device tree support for R-Car r8a7744 (Biju Das)
- Drop unused mvebu PCIe capability code (Thomas Petazzoni)
- Add shared PCI bridge emulation code (Thomas Petazzoni)
- Convert mvebu to use shared PCI bridge emulation (Thomas Petazzoni)
- Add aardvark Root Port emulation (Thomas Petazzoni)
- Support 100MHz/200MHz refclocks for i.MX6 (Lucas Stach)
- Add initial power management for i.MX7 (Leonard Crestez)
- Add PME_Turn_Off support for i.MX7 (Leonard Crestez)
- Fix qcom runtime power management error handling (Bjorn Andersson)
- Update TI dra7xx unaligned access errata workaround for host mode as
well as endpoint mode (Vignesh R)
- Fix kirin section mismatch warning (Nathan Chancellor)
- Remove iproc PAXC slot check to allow VF support (Jitendra Bhivare)
- Quirk Keystone K2G to limit MRRS to 256 (Kishon Vijay Abraham I)
- Update Keystone to use MRRS quirk for host bridge instead of open
coding (Kishon Vijay Abraham I)
- Refactor Keystone link establishment (Kishon Vijay Abraham I)
- Simplify and speed up Keystone link training (Kishon Vijay Abraham I)
- Remove unused Keystone host_init argument (Kishon Vijay Abraham I)
- Merge Keystone driver files into one (Kishon Vijay Abraham I)
- Remove redundant Keystone platform_set_drvdata() (Kishon Vijay
Abraham I)
- Rename Keystone functions for uniformity (Kishon Vijay Abraham I)
- Add Keystone device control module DT binding (Kishon Vijay Abraham
I)
- Use SYSCON API to get Keystone control module device IDs (Kishon
Vijay Abraham I)
- Clean up Keystone PHY handling (Kishon Vijay Abraham I)
- Use runtime PM APIs to enable Keystone clock (Kishon Vijay Abraham I)
- Clean up Keystone config space access checks (Kishon Vijay Abraham I)
- Get Keystone outbound window count from DT (Kishon Vijay Abraham I)
- Clean up Keystone outbound window configuration (Kishon Vijay Abraham
I)
- Clean up Keystone DBI setup (Kishon Vijay Abraham I)
- Clean up Keystone ks_pcie_link_up() (Kishon Vijay Abraham I)
- Fix Keystone IRQ status checking (Kishon Vijay Abraham I)
- Add debug messages for all Keystone errors (Kishon Vijay Abraham I)
- Clean up Keystone includes and macros (Kishon Vijay Abraham I)
- Fix Mediatek unchecked return value from devm_pci_remap_iospace()
(Gustavo A. R. Silva)
- Fix Mediatek endpoint/port matching logic (Honghui Zhang)
- Change Mediatek Root Port Class Code to PCI_CLASS_BRIDGE_PCI (Honghui
Zhang)
- Remove redundant Mediatek PM domain check (Honghui Zhang)
- Convert Mediatek to pci_host_probe() (Honghui Zhang)
- Fix Mediatek MSI enablement (Honghui Zhang)
- Add Mediatek system PM support for MT2712 and MT7622 (Honghui Zhang)
- Add Mediatek loadable module support (Honghui Zhang)
- Detach VMD resources after stopping root bus to prevent orphan
resources (Jon Derrick)
- Convert pcitest build process to that used by other tools (iio, perf,
etc) (Gustavo Pimentel)
* tag 'pci-v4.20-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (140 commits)
PCI/AER: Refactor error injection fallbacks
PCI/AER: Abstract AER interrupt handling
PCI/AER: Reuse existing pcie_port_find_device() interface
PCI/AER: Use managed resource allocations
PCI: pcie: Remove redundant 'default n' from Kconfig
PCI: aardvark: Implement emulated root PCI bridge config space
PCI: mvebu: Convert to PCI emulated bridge config space
PCI: mvebu: Drop unused PCI express capability code
PCI: Introduce PCI bridge emulated config space common logic
PCI: vmd: Detach resources after stopping root bus
nvmet: Optionally use PCI P2P memory
nvmet: Introduce helper functions to allocate and free request SGLs
nvme-pci: Add support for P2P memory in requests
nvme-pci: Use PCI p2pmem subsystem to manage the CMB
IB/core: Ensure we map P2P memory correctly in rdma_rw_ctx_[init|destroy]()
block: Add PCI P2P flag for request queue
PCI/P2PDMA: Add P2P DMA driver writer's documentation
docs-rst: Add a new directory for PCI documentation
PCI/P2PDMA: Introduce configfs/sysfs enable attribute helpers
PCI/P2PDMA: Add PCI p2pmem DMA mappings to adjust the bus offset
...
After bfcb79fca1 ("PCI/ERR: Run error recovery callbacks for all affected
devices"), AER errors are always cleared by the PCI core and drivers don't
need to do it themselves.
Remove calls to pci_cleanup_aer_uncorrect_error_status() from device
driver error recovery functions.
Signed-off-by: Oza Pawandeep <poza@codeaurora.org>
[bhelgaas: changelog, remove PCI core changes, remove unused variables]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We recently updated all our SPDX identifiers to correctly
indicate our net/ethernet/intel/* drivers were always released
and intended to be released under GPL v2, but the MODULE_LICENSE
declaration was never updated.
Fix the MODULE_LICENSE to be GPL v2, for all our drivers.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There have been multiple reports of crashes that look like
kernel: RIP: 0010:[<ffffffff8110303f>] timecounter_read+0xf/0x50
[...]
kernel: Call Trace:
kernel: [<ffffffffa0806b0f>] e1000e_phc_gettime+0x2f/0x60 [e1000e]
kernel: [<ffffffffa0806c5d>] e1000e_systim_overflow_work+0x1d/0x80 [e1000e]
kernel: [<ffffffff810992c5>] process_one_work+0x155/0x440
kernel: [<ffffffff81099e16>] worker_thread+0x116/0x4b0
kernel: [<ffffffff8109f422>] kthread+0xd2/0xf0
kernel: [<ffffffff8163184f>] ret_from_fork+0x3f/0x70
These can be traced back to the fact that e1000e_systim_reset() skips the
timecounter_init() call if e1000e_get_base_timinca() returns -EINVAL, which
leads to a null deref in timecounter_read().
Commit 83129b37ef ("e1000e: fix systim issues", v4.2-rc1) reworked
e1000e_get_base_timinca() in such a way that it can return -EINVAL for
e1000_pch_spt if the SYSCFI bit is not set in TSYNCRXCTL.
Some experimentation has shown that on I219 (e1000_pch_spt, "MAC: 12")
adapters, the E1000_TSYNCRXCTL_SYSCFI flag is unstable; TSYNCRXCTL reads
sometimes don't have the SYSCFI bit set. Retrying the read shortly after
finds the bit to be set. This was observed at boot (probe) but also link up
and link down.
Moreover, the phc (PTP Hardware Clock) seems to operate normally even after
reads where SYSCFI=0. Therefore, remove this register read and
unconditionally set the clock parameters.
Reported-by: Achim Mildenberger <admin@fph.physik.uni-karlsruhe.de>
Message-Id: <20180425065243.g5mqewg5irkwgwgv@f2>
Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=1075876
Fixes: 83129b37ef ("e1000e: fix systim issues")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.
Also caught a few files missing the SPDX license identifier, so fixed
them up.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex reported the following race condition:
/* link goes up... interrupt... schedule watchdog */
\ e1000_watchdog_task
\ e1000e_has_link
\ hw->mac.ops.check_for_link() === e1000e_check_for_copper_link
\ e1000e_phy_has_link_generic(..., &link)
link = true
/* link goes down... interrupt */
\ e1000_msix_other
hw->mac.get_link_status = true
/* link is up */
mac->get_link_status = false
link_active = true
/* link_active is true, wrongly, and stays so because
* get_link_status is false */
Avoid this problem by making sure that we don't set get_link_status = false
after having checked the link.
It seems this problem has been present since the introduction of e1000e.
Link: https://lkml.org/lkml/2018/1/29/338
Reported-by: Alexander Duyck <alexander.duyck@gmail.com>
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This reverts commit 19110cfbb3.
This reverts commit 4110e02eb4.
This reverts commit d3604515c9eda464a92e8e67aae82dfe07fe3c98.
Commit 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
changed what happens to the link status when there is an error which
happens after "get_link_status = false" in the copper check_for_link
callbacks. Previously, such an error would be ignored and the link
considered up. After that commit, any error implies that the link is down.
Revert commit 19110cfbb3 ("e1000e: Separate signaling for link check/link
up") and its followups. After reverting, the race condition described in
the log of commit 19110cfbb3 is reintroduced. It may still be triggered
by LSC events but this should keep the link down in case the link is
electrically unstable, as discussed. The race may no longer be
triggered by RXO events because commit 4aea7a5c5e ("e1000e: Avoid
receiver overrun interrupt bursts") restored reading icr in the Other
handler.
Link: https://lkml.org/lkml/2018/3/1/789
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Descriptor rings were not initialized at zero when allocated
When area contained garbage data, it caused skb_over_panic in
e1000_clean_rx_irq (if data had E1000_RXD_STAT_DD bit set)
This patch makes use of dma_zalloc_coherent to make sure the
ring is memset at 0 to prevent the area from containing garbage.
Following is the signature of the panic:
IODDR0@0.0: skbuff: skb_over_panic: text:80407b20 len:64010 put:64010 head:ab46d800 data:ab46d842 tail:0xab47d24c end:0xab46df40 dev:eth0
IODDR0@0.0: BUG: failure at net/core/skbuff.c:105/skb_panic()!
IODDR0@0.0: Kernel panic - not syncing: BUG!
IODDR0@0.0:
IODDR0@0.0: Process swapper/0 (pid: 0, threadinfo=81728000, task=8173cc00 ,cpu: 0)
IODDR0@0.0: SP = <815a1c0c>
IODDR0@0.0: Stack: 00000001
IODDR0@0.0: b2d89800 815e33ac
IODDR0@0.0: ea73c040 00000001
IODDR0@0.0: 60040003 0000fa0a
IODDR0@0.0: 00000002
IODDR0@0.0:
IODDR0@0.0: 804540c0 815a1c70
IODDR0@0.0: b2744000 602ac070
IODDR0@0.0: 815a1c44 b2d89800
IODDR0@0.0: 8173cc00 815a1c08
IODDR0@0.0:
IODDR0@0.0: 00000006
IODDR0@0.0: 815a1b50 00000000
IODDR0@0.0: 80079434 00000001
IODDR0@0.0: ab46df40 b2744000
IODDR0@0.0: b2d89800
IODDR0@0.0:
IODDR0@0.0: 0000fa0a 8045745c
IODDR0@0.0: 815a1c88 0000fa0a
IODDR0@0.0: 80407b20 b2789f80
IODDR0@0.0: 00000005 80407b20
IODDR0@0.0:
IODDR0@0.0:
IODDR0@0.0: Call Trace:
IODDR0@0.0: [<804540bc>] skb_panic+0xa4/0xa8
IODDR0@0.0: [<80079430>] console_unlock+0x2f8/0x6d0
IODDR0@0.0: [<80457458>] skb_put+0xa0/0xc0
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<804079c8>] e1000_clean_rx_irq+0x188/0x3e8
IODDR0@0.0: [<80407b1c>] e1000_clean_rx_irq+0x2dc/0x3e8
IODDR0@0.0: [<80468b48>] __dev_kfree_skb_any+0x88/0xa8
IODDR0@0.0: [<804101ac>] e1000e_poll+0x94/0x288
IODDR0@0.0: [<8046e9d4>] net_rx_action+0x19c/0x4e8
IODDR0@0.0: ...
IODDR0@0.0: Maximum depth to print reached. Use kstack=<maximum_depth_to_print> To specify a custom value (where 0 means to display the full backtrace)
IODDR0@0.0: ---[ end Kernel panic - not syncing: BUG!
Signed-off-by: Pierre-Yves Kerbrat <pkerbrat@kalray.eu>
Signed-off-by: Marius Gligor <mgligor@kalray.eu>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When autoneg is off, the .check_for_link callback functions clear the
get_link_status flag and systematically return a "pseudo-error". This means
that the link is not detected as up until the next execution of the
e1000_watchdog_task() 2 seconds later.
Fixes: 19110cfbb3 ("e1000e: Separate signaling for link check/link up")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The 82574 specification update errata 12 states that interrupts may be
missed if ICR is read while INT_ASSERTED is not set. Avoid that problem by
setting all bits related to events that can trigger the Other interrupt in
IMS.
The Other interrupt is raised for such events regardless of whether or not
they are set in IMS. However, only when they are set is the INT_ASSERTED
bit also set in ICR.
By doing this, we ensure that INT_ASSERTED is always set when we read ICR
in e1000_msix_other() and steer clear of the errata. This also ensures that
ICR will automatically be cleared on read, therefore we no longer need to
clear bits explicitly.
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Restores the ICS write for Rx/Tx queue interrupts which was present before
commit 16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1)
but was not restored in commit 4aea7a5c5e
("e1000e: Avoid receiver overrun interrupt bursts", v4.15-rc1).
This re-raises the queue interrupts in case the txq or rxq bits were set in
ICR and the Other interrupt handler read and cleared ICR before the queue
interrupt was raised.
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This partially reverts commit 4aea7a5c5e.
We keep the fix for the first part of the problem (1) described in the log
of that commit, that is to read ICR in the other interrupt handler. We
remove the fix for the second part of the problem (2), Other interrupt
throttling.
Bursts of "Other" interrupts may once again occur during rxo (receive
overflow) traffic conditions. This is deemed acceptable in the interest of
avoiding unforeseen fallout from changes that are not strictly necessary.
As discussed, the e1000e driver should be in "maintenance mode".
Link: https://www.spinics.net/lists/netdev/msg480675.html
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
It was reported that emulated e1000e devices in vmware esxi 6.5 Build
7526125 do not link up after commit 4aea7a5c5e ("e1000e: Avoid receiver
overrun interrupt bursts", v4.15-rc1). Some tracing shows that after
e1000e_trigger_lsc() is called, ICR reads out as 0x0 in e1000_msix_other()
on emulated e1000e devices. In comparison, on real e1000e 82574 hardware,
icr=0x80000004 (_INT_ASSERTED | _LSC) in the same situation.
Some experimentation showed that this flaw in vmware e1000e emulation can
be worked around by not setting Other in EIAC. This is how it was before
16ecba59bc ("e1000e: Do not read ICR in Other interrupt", v4.5-rc1).
Fixes: 4aea7a5c5e ("e1000e: Avoid receiver overrun interrupt bursts")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
I personally spent a long time trying to decypher why my CPU would not
reach deeper C-states. Let's just tell the next user what's going on.
Signed-off-by: Matt Turner <matt.turner@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
