Commit cae9ff036e effectively disabled the drm poll_helper by checking
the wrong flag to see if the driver should enable the poll or not:
mode_config.poll_enabled is only set to true by poll_init and it is not
indicating if the poll is enabled or not.
nouveau_display_create() will initialize the poll and going to disable it
right away. After poll_init() the mode_config.poll_enabled will be true,
but the poll itself is disabled.
To avoid the race caused by calling the poll_enable() from different paths,
this patch will enable the poll from one place, in the
nouveau_display_hpd_work().
In case the pm_runtime is disabled we will enable the poll in
nouveau_drm_load() once.
Fixes: cae9ff036e ("drm/nouveau: Don't enabling polling twice on runtime resume")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reviewed-by: Lyude <lyude@redhat.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
BCM2835's PLLD_DSI1 divider doesn't give us many choices for our pixel
clocks, so to support panels on the Raspberry Pi we need to set a
higher pixel clock rate than requested and adjust the mode we program
to extend out the HFP so that the refresh rate matches.
v2: Drop an unfinished comment (caught by Noralf)
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511235625.22427-2-eric@anholt.net
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
If a vma is already bound to a ppgtt, we incorrectly call
allocate_va_range again when doing a PIN_UPDATE, which will result in
over accounting within our paging structures, such that when we do
unbind something we don't actually destroy the structures and end up
inadvertently recycling them. In reality this probably isn't too bad,
but once we start touching PDEs and PDPEs for 64K/2M/1G pages this
apparent recycling will manifest into lots of really, really subtle
bugs.
v2: Fix the testing of vma->flags for aliasing_ppgtt_bind_vma
Fixes: ff685975d9 ("drm/i915: Move allocate_va_range to GTT")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170512091423.26085-1-chris@chris-wilson.co.uk
(cherry picked from commit 1f23475c89)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Turns out our skills in decoding the CLKCFG register weren't good
enough. On this particular elk the answer we got was 400 MHz when
in reality the clock was running at 266 MHz, which then caused us
to program a bogus AUX clock divider that caused all AUX communication
to fail.
Sadly the docs are now in bit heaven, so the fix will have to be based
on empirical evidence. Using another elk machine I was able to frob
the FSB frequency from the BIOS and see how it affects the CLKCFG
register. The machine seesm to use a frequency of 266 MHz by default,
and fortunately it still boot even with the 50% CPU overclock that
we get when we bump the FSB up to 400 MHz.
It turns out the actual FSB frequency and the register have no real
link whatsoever. The register value is based on some straps or something,
but fortunately those too can be configured from the BIOS on this board,
although it doesn't seem to respect the settings 100%. In the end I was
able to derive the following relationship:
BIOS FSB / strap | CLKCFG
-------------------------
200 | 0x2
266 | 0x0
333 | 0x4
400 | 0x4
So only the 200 and 400 MHz cases actually match how we're currently
decoding that register. But as the comment next to some of the defines
says, we have been just guessing anyway.
So let's fix things up so that at least the 266 MHz case will work
correctly as that is actually the setting used by both the buggy
machine and my test machine.
The fact that 333 and 400 MHz BIOS settings result in the same register
value is a little disappointing, as that means we can't tell them apart.
However, according to the gmch datasheet for both elk and ctg 400 Mhz is
not even a supported FSB frequency, so I'm going to make the assumption
that we should decode it as 333 MHz instead.
Cc: stable@vger.kernel.org
Cc: Tomi Sarvela <tomi.p.sarvela@intel.com>
Reported-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=100926
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170504181530.6908-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
(cherry picked from commit 6f38123eca)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Not calling pm_runtime_enable() means that runtime PM can't be
enabled at all via sysfs. So we definitely need to call it
from somewhere.
Calling it from the driver seems like a bad idea because it
would have to be paired with a pm_runtime_disable() at driver
unload time, otherwise the core gets upset. Also if there's
no LPE audio driver loaded then we couldn't runtime suspend
i915 either.
So it looks like a better plan is to call it from i915 when
we register the platform device. That seems to match how
pci generally does things. I cargo culted the
pm_runtime_forbid() and pm_runtime_set_active() calls from
pci as well.
The exposed runtime PM API is massive an thorougly misleading, so
I don't actually know if this is how you're supposed to use the API
or not. But it seems to work. I can now runtime suspend i915 again
with or without the LPE audio driver loaded, and reloading the
LPE audio driver also seems to work.
Note that powertop won't auto-tune runtime PM for platform devices,
which is a little annoying. So I'm not sure that leaving runtime
PM in "on" mode by default is the best choice here. But I've left
it like that for now at least.
Also remove the comment about there not being much benefit from
LPE audio runtime PM. Not allowing runtime PM blocks i915 runtime
PM, which will also block s0ix, and that could have a measurable
impact on power consumption.
Cc: stable@vger.kernel.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Fixes: 0b6b524f39 ("ALSA: x86: Don't enable runtime PM as default")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170427160231.13337-2-ville.syrjala@linux.intel.com
Reviewed-by: Takashi Iwai <tiwai@suse.de>
(cherry picked from commit 183c00350c)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
As we are going to add support for the Allwinner DE2 Mixer in sun4i-drm
driver, we will finally have two types of layers.
Each layer is bound to a drm_plane that is CRTC-specific, so we create
them when initializing CRTC (calling sun4i_layers_init, which will be
generalized in next patch). The drm_plane's will be used when creating
CRTC, but the CRTC initialization code do not care other properties of
the layer, so we let the sun4i_layers_init function return drm_plane's
only.
As we have no need to trace the layers after the CRTC is properly
created, we drop the layers pointer in sun4i_crtc struct.
Doing this uncouples the CRTC code from the type of layer (the
sun4i_layers_init function name is still hardcoded and will be changed
in the next patch), so that we can finally gain support for the
mixer in DE2, which has different layers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
sun4i_backend_layer_enable can be called to enable or disable a layer.
However the debug message always says "Enable", which is confusing.
This patch makes the debug message vary according to the enable state.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Currently we are configuring the TCON's dot clock or special clock
directly from the encoder mode_set functions. Since we already
provide mode_set helper functions for the TCON's 2 channels, we
can set the respective clock from those helpers, and reduce the
exposure of the TCON's internals.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The tcons and backends have a one-to-one relationship. Their IDs,
or indexes in the documentation, are also the same.
Copy the ID from the associated backend and save it in the tcon
structure. This will later be used when we add support for the
output data path muxes.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
With Allwinner's Display Engine 1.0, each TCON's input is tied to a
specific display backend, and the 2 comprise what is known as a crtc
in DRM KMS land: The layer, framebuffer, and compositing functions are
provided by the backend, while the TCON provides the display timing
signals and vblank interrupts. This 1 to 1 relationship is represented
in the device tree. On some systems there is an intermediate DRC
component.
Pointers to both matching components must be provided when initializing
the crtc. As the backend is always registered before the associated
tcon, we can recursively search upwards through the of_graph to find
the matching backend.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Save a pointer to the backend's underlying device tree node in its
data structure. This will be used later for downstream tcons to find
and match their respective upstream backends.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Some Allwinner SoCs have 2 display pipelines, as in 2 of each
components, including the frontend, backend, TCON, and any other
extras.
As the backend and TCON are always paired together and form the CRTC,
we need to know which backend or TCON we are currently probing, so we
can pair them when initializing the CRTC.
This patch figures out the backend's ID from the device tree and stores
it in the backend's data structure. It does this by looking at the "reg"
property of any remote endpoints connected to the backend's input port.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we support multiple instances of backends, the trailing 0
implying only one backend no longer makes sense.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
To support multiple display pipelines, we need to keep track of the
multiple display backends and TCONs registered with the driver.
Switch to lists to track registered components. Components are only
appended to their respective lists if the bind process was successful.
The TCON bind function now defers if a backend was not registered.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
This change is pre-emptively aiming to avoid a potential cause of kernel
logging noise in case some condition were to result in us seeing invalid
OA reports.
The workaround for the OA unit's tail pointer race condition is what
avoids the primary known cause of invalid reports being seen and with
that in place we aren't expecting to see this notice but it can't be
entirely ruled out.
Just in case some condition does lead to the notice then it's likely
that it will be triggered repeatedly while attempting to append a
sequence of reports and depending on the configured OA sampling
frequency that might be a large number of repeat notices.
v2: (Chris) avoid inconsistent warning on throttle with
printk_ratelimit()
v3: (Matt) init and summarise with stream init/close not driver init/fini
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-9-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There's a HW race condition between OA unit tail pointer register
updates and writes to memory whereby the tail pointer can sometimes get
ahead of what's been written out to the OA buffer so far (in terms of
what's visible to the CPU).
Although this can be observed explicitly while copying reports to
userspace by checking for a zeroed report-id field in tail reports, we
want to account for this earlier, as part of the _oa_buffer_check to
avoid lots of redundant read() attempts.
Previously the driver used to define an effective tail pointer that
lagged the real pointer by a 'tail margin' measured in bytes derived
from OA_TAIL_MARGIN_NSEC and the configured sampling frequency.
Unfortunately this was flawed considering that the OA unit may also
automatically generate non-periodic reports (such as on context switch)
or the OA unit may be enabled without any periodic sampling.
This improves how we define a tail pointer for reading that lags the
real tail pointer by at least %OA_TAIL_MARGIN_NSEC nanoseconds, which
gives enough time for the corresponding reports to become visible to the
CPU.
The driver now maintains two tail pointers:
1) An 'aging' tail with an associated timestamp that is tracked until we
can trust the corresponding data is visible to the CPU; at which point
it is considered 'aged'.
2) An 'aged' tail that can be used for read()ing.
The two separate pointers let us decouple read()s from tail pointer aging.
The tail pointers are checked and updated at a limited rate within a
hrtimer callback (the same callback that is used for delivering POLLIN
events) and since we're now measuring the wall clock time elapsed since
a given tail pointer was read the mechanism no longer cares about
the OA unit's periodic sampling frequency.
The natural place to handle the tail pointer updates was in
gen7_oa_buffer_is_empty() which is called as part of blocking reads and
the hrtimer callback used for polling, and so this was renamed to
oa_buffer_check() considering the added side effect while checking
whether the buffer contains data.
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-6-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
This avoids redundantly passing an (inout) head and tail pointer to
gen7_append_oa_reports() from gen7_oa_read which doesn't need to
reference either itself.
Moving the head/tail reads and writes into gen7_append_oa_reports should
have no functional effect except to avoid some redundant head pointer
writes in cases where nothing was copied to userspace.
This is a stepping stone towards updating how the head and tail pointer
state is managed to improve the workaround for the OA unit's tail
pointer race. It reduces the number of places we need to read/write the
head and tail pointers.
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-5-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
There's no need for the driver to keep reading back the head pointer
from hardware since the hardware doesn't update it automatically. This
way we can treat any invalid head pointer value as a software/driver
bug instead of spurious hardware behaviour.
This change is also a small stepping stone towards re-working how
the head and tail state is managed as part of an improved workaround
for the tail register race condition.
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-4-lionel.g.landwerlin@intel.com
If the function for checking whether there is OA buffer data available
(during a poll or blocking read) has false positives then we want to
avoid a situation where the subsequent read() returns EAGAIN (after
a more accurate check) followed by a poll() immediately reporting
the same false positive POLLIN event and effectively maintaining a
busy loop until there really is data.
This makes sure that we clear the .pollin event status whenever we
return EAGAIN to userspace which will throttle subsequent POLLIN events
and repeated attempts to read to the 5ms intervals of the hrtimer
callback we have.
Signed-off-by: Robert Bragg <robert@sixbynine.org>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170511154345.962-3-lionel.g.landwerlin@intel.com
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
If a vma is already bound to a ppgtt, we incorrectly call
allocate_va_range again when doing a PIN_UPDATE, which will result in
over accounting within our paging structures, such that when we do
unbind something we don't actually destroy the structures and end up
inadvertently recycling them. In reality this probably isn't too bad,
but once we start touching PDEs and PDPEs for 64K/2M/1G pages this
apparent recycling will manifest into lots of really, really subtle
bugs.
v2: Fix the testing of vma->flags for aliasing_ppgtt_bind_vma
Fixes: ff685975d9 ("drm/i915: Move allocate_va_range to GTT")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20170512091423.26085-1-chris@chris-wilson.co.uk
Add a new Kconfig option to enable/disable the extra warnings
from the vblank evade code. For now we'll keep the warning
about an actually missed vblank always enabled as that can have
an actual user visible impact. But if we miss the deadline
othrwise there's no real need to bother the user with that.
We'll want these warnings enabled during development however
so that we can catch regressions.
Based on the reports it looks like this is still very easy
to hit on SKL, so we have more work ahead of us to optimize
the crtiical section further.
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: Jens Axboe <axboe@kernel.dk>
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes: e1edbd44e2 ("drm/i915: Complain if we take too long under vblank evasion.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Quite a few patches, but not much code changed:
- Fixes regression from atomic when only the source rect of a plane
changes (ie. xrandr --right-of)
- Fixes another issue where atomic changed behaviour underneath us,
potentially causing laggy cursor position updates
- Fixes for a bunch of races in thermal code, which lead to random
lockups for a lot of users
* 'linux-4.12' of git://github.com/skeggsb/linux:
drm/nouveau/therm: remove ineffective workarounds for alarm bugs
drm/nouveau/tmr: avoid processing completed alarms when adding a new one
drm/nouveau/tmr: fix corruption of the pending list when rescheduling an alarm
drm/nouveau/tmr: handle races with hw when updating the next alarm time
drm/nouveau/tmr: ack interrupt before processing alarms
drm/nouveau/core: fix static checker warning
drm/nouveau/fb/ram/gf100-: remove 0x10f200 read
drm/nouveau/kms/nv50: skip core channel cursor update on position-only changes
drm/nouveau/kms/nv50: fix source-rect-only plane updates
drm/nouveau/kms/nv50: remove pointless argument to window atomic_check_acquire()
Fixes for 4.12. This is a bit bigger than usual since it's 3 weeks
worth of fixes and most of these changes are for vega10 which is
new for 4.12 and still in a fair amount of flux. It looks like
you missed my last pull request, so those patches are included here
as well. Highlights:
- Lots of vega10 fixes
- Fix interruptable wait mixup
- Fan control method fixes
- Misc display fixes for radeon and amdgpu
- Misc bug fixes
* 'drm-next-4.12' of git://people.freedesktop.org/~agd5f/linux: (132 commits)
drm/amd/powerplay: refine pwm1_enable callback functions for CI.
drm/amd/powerplay: refine pwm1_enable callback functions for vi.
drm/amd/powerplay: refine pwm1_enable callback functions for Vega10.
drm/amdgpu: refine amdgpu pwm1_enable sysfs interface.
drm/amdgpu: add amd fan ctrl mode enums.
drm/amd/powerplay: add more smu message on Vega10.
drm/amdgpu: fix dependency issue
drm/amd: fix init order of sched job
drm/amdgpu: add some additional vega10 pci ids
drm/amdgpu/soc15: use atomfirmware for setting bios scratch for reset
drm/amdgpu/atomfirmware: add function to update engine hang status
drm/radeon: only warn once in radeon_ttm_bo_destroy if va list not empty
drm/amdgpu: fix mutex list null pointer reference
drm/amd/powerplay: fix bug sclk/mclk level can't be set on vega10.
drm/amd/powerplay: Setup sw CTF to allow graceful exit when temperature exceeds maximum.
drm/amd/powerplay: delete dead code in powerplay.
drm/amdgpu: Use less generic enum definitions
drm/amdgpu/gfx9: derive tile pipes from golden settings
drm/amdgpu/gfx: drop max_gs_waves_per_vgt
drm/amd/powerplay: disable engine spread spectrum feature on Vega10.
...
