We are using PSP to resume firmware after suspend, and it is
resumed at where it got suspended, so we'd better save the
the context.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In review, Christian would like to keep the logic
inside amdgpu_vm.c with a cost of slightly slower.
The loop is still optimized out with this patch.
v2: remove the if statement. Now it is not slower.
Signed-off-by: Alex Xie <AlexBin.Xie@amd.com>
Reviewed-by: Christian König <christian.koeng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Atm disabling either DP or eDP outputs can generate a spurious short
pulse interrupt. The reason is that after disabling the port the source
will stop sending a valid stream data, while the sink expects either a
valid stream or the idle pattern. Since neither of this is sent the sink
assumes (after an arbitrary delay) that the link is lost and requests
for link retraining with a short pulse.
The spurious pulse is a real problem at least for eDP panels with long
power-off / power-cycle delays: as part of disabling the output we
disable the panel power. The subsequent spurious short pulse handling
will have to turn the power back on, which means the driver has to do a
redundant wait for the power-off and power-cycle delays. During system
suspend this leads to an unnecessary delay up to ~1s on systems with
such panels as reported by Rui.
To fix this put the sink to DPMS D3 state before turning off the port.
According to the DP spec in this state the sink should not request
retraining. This is also what we do already on pre-ddi platforms.
As an alternative I also tried configuring the port to send idle pattern
- which is against BSPec - and leave the port in normal mode before
turning off the port. Neither of these resolved the problem.
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: David Weinehall <david.weinehall@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reported-and-tested-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1496250335-7627-1-git-send-email-imre.deak@intel.com
We accidentally return ERR_PTR(0) which is NULL. The caller is not
expecting that and it leads to an Oops.
Fixes: dd59239a98 ("amdkfd: init aperture once per process")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Oded Gabbay <oded.gabbay@gmail.com>
The A10s has a slightly different display pipeline than the A13, with an
HDMI controller.
Add a compatible for it.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The earlier Allwinner SoCs (A10, A10s, A20, A31) have an embedded HDMI
controller.
That HDMI controller is able to do audio and CEC, but those have been left
out for now.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The generic connectors such as hdmi-connector doesn't have any driver in,
so if they are added to the component list, we will be waiting forever for
a non-existing driver to probe.
Add a list of the connectors we want to ignore when building our component
list.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It appears that the total vertical resolution needs to be doubled when
we're not in interlaced. Make sure that is the case.
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Both TCON channels need to have the resolution doubled, since the size the
hardware is going to use is whatever we put in the register divided by two.
However, we handle it differently for the two channels: in the channel 0,
our register access macro does the multiplication of the value passed as
paremeter, while in the channel 1, the macro doesn't do this, and we need
to do it before calling it.
Make this consistent by aligning the channel 0 with the channel 1
behaviour.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
It seems like what's called a backporch in the datasheet is actually the
backporch plus the sync period. Fix that in our driver.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The muxing can actually happen on both channels on some SoCs, so it makes
more sense to just move it out of the sun4i_tcon1_mode_set function and
create a separate function that needs to be called by the encoders.
Let's do that and convert the existing drivers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
While all functions have debug logs, the channel enable and disable are not
logged. Make sure this is the case.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner V3s features the new "Display Engine 2.0", which can now also
be driven with our subdrivers in sun4i-drm.
Add the compatible string for in sun4i_drv.c, in order to make the
display engine and its components probed.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Allwinner have a new "Display Engine 2.0" in their new SoCs, which comes
with mixers to do graphic processing and feed data to TCON, like the old
backends and frontends.
Add support for the mixer on Allwinner V3s SoC; it's the simplest one.
Currently a lot of functions are still missing -- more investigations
are needed to gain enough information for them.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As sun4i-backend is now a dedicated module, add an Kconfig option for
it to make it optional, since some build may only use other engines.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
A display resolution is only supported if it meets all the restrictions
below for Maximum Pipe Pixel Rate.
The display resolution must fit within the maximum pixel rate output
from the pipe. Make sure that the display pipe is able to feed pixels at
a rate required to support the desired resolution.
For each enabled plane on the pipe {
If plane scaling enabled {
Horizontal down scale amount = Maximum[1, plane horizontal size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, plane vertical size /
scaler vertical window size]
Plane down scale amount = Horizontal down scale amount *
Vertical down scale amount
Plane Ratio = 1 / Plane down scale amount
}
Else {
Plane Ratio = 1
}
If plane source pixel format is 64 bits per pixel {
Plane Ratio = Plane Ratio * 8/9
}
}
Pipe Ratio = Minimum Plane Ratio of all enabled planes on the pipe
If pipe scaling is enabled {
Horizontal down scale amount = Maximum[1, pipe horizontal source size /
scaler horizontal window size]
Vertical down scale amount = Maximum[1, pipe vertical source size /
scaler vertical window size]
Note: The progressive fetch - interlace display mode is equivalent to a
2.0 vertical down scale
Pipe down scale amount = Horizontal down scale amount *
Vertical down scale amount
Pipe Ratio = Pipe Ratio / Pipe down scale amount
}
Pipe maximum pixel rate = CDCLK frequency * Pipe Ratio
In this patch our calculation is based on pipe downscale amount
(plane max downscale amount * pipe downscale amount) instead of Pipe
Ratio. So,
max supported crtc clock with given scaling = CDCLK / pipe downscale.
Flip will fail if,
current crtc clock > max supported crct clock with given scaling.
Changes since V1:
- separate out fixed_16_16 wrapper API definition
Changes since V2:
- Fix buggy crtc !active condition (Maarten)
- use intel_wm_plane_visible wrapper as per Maarten's suggestion
Changes since V3:
- Change failure return from ERANGE to EINVAL
Changes since V4:
- Rebase based on previous patch changes
Changes since V5:
- return EINVAL instead of continue (Maarten)
Changes since V6:
- Improve commit message
- Address review comment
Changes since V7:
- use !enable instead of !active
- rename config variable for consistency (Maarten)
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170526151546.25025-4-mahesh1.kumar@intel.com
This patch implements new DDB allocation algorithm as per HW team
recommendation. This algo takecare of scenario where we allocate less DDB
for the planes with lower relative pixel rate, but they require more DDB
to work.
It also takes care of enabling same watermark level for each
plane in crtc, for efficient power saving.
Changes since v1:
- Rebase on top of Paulo's patch series
Changes since v2:
- Fix the for loop condition to enable WM
Changes since v3:
- Fix crash in cursor i-g-t reported by Maarten
- Rebase after addressing Paulo's comments
- Few other ULT fixes
Changes since v4:
- Rebase on drm-tip
- Added separate function to enable WM levels
Changes since v5:
- Fix a crash identified in skl-6770HQ system
Changes since v6:
- Address review comments from Matt
Changes since v7:
- Fix failure return in skl_compute_plane_wm (Matt)
- fix typo
Changes since v8:
- Always check cursor wm enable irrespective of total_data_rate
Changes since v9:
- fix typo
Signed-off-by: Mahesh Kumar <mahesh1.kumar@intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170601055918.4601-1-mahesh1.kumar@intel.com
As we are going to add support for the Allwinner DE2 engine in sun4i-drm
driver, we will finally have two types of display engines -- the DE1
backend and the DE2 mixer. They both do some display blending and feed
graphics data to TCON, and is part of the "Display Engine" called by
Allwinner, so I choose to call them both "engine" here.
Abstract the engine type to a new struct with an ops struct, which contains
functions that should be called outside the engine-specified code (in
TCON, CRTC or TV Encoder code).
In order to preserve bisectability, we also switch the backend and layer
code in its own module.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
TE IRQ is enabled only in case of sw-trigger, so trigger check
is redundant.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Exynos tracked suspend state to prevent touching disabled HW. After
fixing disable order in HDMI and moving TE handling to DECON it is
not needed anymore - all IRQ handlers and callbacks touching HW
are called only with enabled DECON.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The flag was used to trigger software update in TE IRQ handler only
if framebuffers were replaced. Since TE update is triggered always
when VBLANKs are enabled and after framebuffer replacement VBLANKs
are always enabled the flag becomes redundant.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The flag was used to check if IRQ handlers can touch HW. Since driver
enables IRQs only if hardware is enabled the flag becomes redundant.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since DECON uses enable_irq/disable_irq to full control IRQs,
there is no point in having flags to trace it separately.
As a bonus condition for software trigger becomes always true,
so it can be removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DECON is the only user of TE signal, moving all TE related
code to DECON driver allows to precise control of IRQ handlers.
This control allows to fix race between IRQ handler and DECON disable
code - now it is possible to disable DECON during IRQ handling
which can result in kernel crash. Beside race fixing this change
allows further code simplification.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
When vblanks are enabled userspace and/or kernel can expect vblank
interrupt at declared period of time. To generate vblank interrupt
image transfer must be triggered. This patch fixes vblank timeouts
in case of sw-trigger mode.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
The output stage of the mixer uses YCbCr for the internal
computations, which is the reason that some registers take
YCbCr related data as input. In particular this applies
to MXR_BG_COLOR{0,1,2} and MXR_CM_COEFF_{Y,CB,CR}.
Document the formatting of the data which we write to
these registers.
While at it, unify wording of comments in the register header.
Reviewed-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
DSIM uses MIC bridge which is between DECON and DSIM, so the driver
should expect bridge node on input side.
Fixes: 86418f9 ("drm: convert drivers to use of_graph_get_remote_node")
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Hardware require that MIXER(crtc) should be disabled prior to
HDMI(encoder). It was achieved by disabling crtc from encoder disable
callback, bypassing drm core. As a result drm core tried to call vblank
related routines on disabled crtc. The patch fixes it by simplifying
hdmi_disable routine - now it only cancels hotplug worker. Hardware will
be disabled in proper moment during pipe clock disable.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
There is no point in protecting only particular windows during update.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
BIT_IRQS_ENABLED flag duplicates drm_vblank_crtc::refcount, it could be
safely removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since fixing CMU code (drm/exynos/decon5433: fix CMU programming)
DECON started behave predictable and does not need special care
during DECON_UPDATE writes.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
All Exynos CRTCs are fully configured by .enable callback. The only users
of mode_set_nofb actually did nothing in their callbacks - they immediately
returned because devices were in suspend state - mode_set_nofb is always
called on disabled device.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Since possible_crtcs are set by Exynos core helper pipe fields have no
raison d'etre. The only place it was used, as a hack, is
fimd_clear_channels, to avoid calling drm_crtc_handle_vblank, but DRM core
has already other protection mechanism (vblank->enabled), so it could be
safely removed.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
