When I test to use the CY8CTMA340 with PostmarketOS I don't have any
problem whatsoever in dropping this phys path, it finds and uses the
touchscreen just as well. I suppose it is because userspace is using
modern input libraries.
I challenge the maintainers to point out a valid and still used
userspace that actually need this. I say we drop it.
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210408131153.3446138-7-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The data sheet for CY8CTMA340 specifies that the reset pulse shall be at
least 1 ms. Specify 1-2 ms with usleep_range() to cut some slack for the
scheduler.
Curiously the datasheet does not specify how long we have to wait after a
hard reset until the chip is up, but I have found a vendor tree (Samsung
GT-S7710) that has code for this touch screen and there this is set to 5
ms so I use this with the same 1 ms fuzz.
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210408131153.3446138-6-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Provide a proper error message when attempting to exit boot loader mode
and failing, which is something that happened to me.
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210408131153.3446138-5-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the following gcc warning:
drivers/input/serio/apbps2.c:106:16: warning: variable ‘tmp’ set but not
used [-Wunused-but-set-variable].
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/1617958859-64707-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Melfas MMS136 is similar to the other MMS variants but
has event packages of 6 bytes rather than 8 as the others.
The define is named FINGER_EVENT_SZ in the vendor drivers
so I renamed it from MMS*_PACKET_SZ to MMS*_EVENT_SZ.
After this patch, the touchscreen on the Samsung GT-I8530
works fine with PostmarketOS.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210404232619.3092682-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for ILITEK Lego series of touch devices.
Lego series includes ILITEK 213X/23XX/25XX.
Tested/passed with evaluation board with ILI2520/2322 IC.
Signed-off-by: Joe Hung <joe_hung@ilitek.com>
Link: https://lore.kernel.org/r/20210324122601.125873-2-joe_hung@ilitek.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the msg2638 touchscreen IC from MStar.
Firmware handling, wakeup gestures and other specialties are not supported.
This driver reuses zinitix.c structure, while the checksum and irq handler
functions are based on out-of-tree driver for Alcatel Idol 3 (4.7").
Signed-off-by: Vincent Knecht <vincent.knecht@mailoo.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210305153815.126937-2-vincent.knecht@mailoo.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some buggy BIOS-es bring up the touchscreen-controller in a stuck
state where it blocks the I2C bus. Specifically this happens on
the Jumper EZpad 7 tablet model.
After much poking at this problem I have found that the following steps
are necessary to unstuck the chip / bus:
1. Turn off the Silead chip.
2. Try to do an I2C transfer with the chip, this will fail in response to
which the I2C-bus-driver will call: i2c_recover_bus() which will unstuck
the I2C-bus. Note the unstuck-ing of the I2C bus only works if we first
drop the chip of the bus by turning it off.
3. Turn the chip back on.
On the x86/ACPI systems were this problem is seen, step 1. and 3. require
making ACPI calls and dealing with ACPI Power Resources. This commit adds
a workaround which runtime-suspends the chip to turn it off, leaving it up
to the ACPI subsystem to deal with all the ACPI specific details.
There is no good way to detect this bug, so the workaround gets activated
by a new "silead,stuck-controller-bug" boolean device-property. Since this
is only used on x86/ACPI, this will be set by model specific device-props
set by drivers/platform/x86/touchscreen_dmi.c. Therefor this new
device-property is not documented in the DT-bindings.
Dmesg will contain the following messages on systems where the workaround
is activated:
[ 54.309029] silead_ts i2c-MSSL1680:00: [Firmware Bug]: Stuck I2C bus: please ignore the next 'controller timed out' error
[ 55.373593] i2c_designware 808622C1:04: controller timed out
[ 55.582186] silead_ts i2c-MSSL1680:00: Silead chip ID: 0x80360000
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202745.16777-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Several users have been reporting that elants_i2c gives several errors
during probe and that their touchscreen does not work on their Lenovo AMD
based laptops with a touchscreen with a ELAN0001 ACPI hardware-id:
[ 0.550596] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vcc33 not found, using dummy regulator
[ 0.551836] elants_i2c i2c-ELAN0001:00: i2c-ELAN0001:00 supply vccio not found, using dummy regulator
[ 0.560932] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.562427] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.595925] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.597974] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.621893] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (77 77 77 77): -121
[ 0.622504] elants_i2c i2c-ELAN0001:00: software reset failed: -121
[ 0.632650] elants_i2c i2c-ELAN0001:00: elants_i2c_send failed (4d 61 69 6e): -121
[ 0.634256] elants_i2c i2c-ELAN0001:00: boot failed: -121
[ 0.699212] elants_i2c i2c-ELAN0001:00: invalid 'hello' packet: 00 00 ff ff
[ 1.630506] elants_i2c i2c-ELAN0001:00: Failed to read fw id: -121
[ 1.645508] elants_i2c i2c-ELAN0001:00: unknown packet 00 00 ff ff
Despite these errors, the elants_i2c driver stays bound to the device
(it returns 0 from its probe method despite the errors), blocking the
i2c-hid driver from binding.
Manually unbinding the elants_i2c driver and binding the i2c-hid driver
makes the touchscreen work.
Check if the ACPI-fwnode for the touchscreen contains one of the i2c-hid
compatiblity-id strings and if it has the I2C-HID spec's DSM to get the
HID descriptor address, If it has both then make elants_i2c not bind,
so that the i2c-hid driver can bind.
This assumes that non of the (older) elan touchscreens which actually
need the elants_i2c driver falsely advertise an i2c-hid compatiblity-id
+ DSM in their ACPI-fwnodes. If some of them actually do have this
false advertising, then this change may lead to regressions.
While at it also drop the unnecessary DEVICE_NAME prefixing of the
"I2C check functionality error", dev_err already outputs the driver-name.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207759
Acked-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210405202756.16830-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
My brain-damaged adjustments to Paul's patch caused crashes in
gpio_keys_disable_button() when driver is used in GPIO-less (i.e.
purely interrupt-driven) setups, because I mixed together debounce and
release timers when they are in fact separate:
Unable to handle kernel NULL pointer dereference at virtual address 0000000c
...
PC is at hrtimer_active+0xc/0x98
LR is at hrtimer_try_to_cancel+0x24/0x140
...
[<c01c43b8>] (hrtimer_active) from [<c01c50f4>] (hrtimer_try_to_cancel+0x24/0x140)
[<c01c50f4>] (hrtimer_try_to_cancel) from [<c01c5224>] (hrtimer_cancel+0x14/0x4c)
[<c01c5224>] (hrtimer_cancel) from [<bf1cae24>] (gpio_keys_attr_store_helper+0x1b8/0x1d8 [gpio_keys])
[<bf1cae24>] (gpio_keys_attr_store_helper [gpio_keys]) from [<bf1cae80>] (gpio_keys_store_disabled_keys+0x18/0x24 [gpio_keys])
[<bf1cae80>] (gpio_keys_store_disabled_keys [gpio_keys]) from [<c038ec7c>] (kernfs_fop_write_iter+0x10c/0x1cc)
[<c038ec7c>] (kernfs_fop_write_iter) from [<c02df858>] (vfs_write+0x2ac/0x404)
[<c02df858>] (vfs_write) from [<c02dfaf4>] (ksys_write+0x64/0xdc)
[<c02dfaf4>] (ksys_write) from [<c0100080>] (ret_fast_syscall+0x0/0x58)
Let's fix it up.
Fixes: c9efb0ba28 ("Input: gpio-keys - use hrtimer for software debounce, if possible")
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/YG1DFFgojSVfdpaz@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Drop unnecessary zero-checking of ABS_MT_TOUCH_MAJOR resolution since
there is no difference between setting resolution to 0 vs not setting
it at all. This change makes code cleaner a tad.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210328235507.19240-1-digetx@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Touchscreen firmware of ASUS Transformer TF700T reports zeros for the phys
size. Hence check whether the size is zero and don't set the resolution in
this case.
Reported-by: Jasper Korten <jja2000@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210302100824.3423-1-digetx@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i.MX has been converted to a DT-only platform, so make the
adjustments to the driver to convert it to a DT-only driver.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210327194307.541248-1-festevam@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable because of requesting.
On the other hand, request_irq() after setting IRQ_NOAUTOEN as
below
irq_set_status_flags(irq, IRQ_NOAUTOEN);
request_irq(dev, irq...);
can also be replaced by request_irq() with IRQF_NO_AUTOEN flag.
Signed-off-by: Barry Song <song.bao.hua@hisilicon.com>
Link: https://lore.kernel.org/r/20210302224916.13980-3-song.bao.hua@hisilicon.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmBXwRseHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGX80H/2qQ49e2lbOfIqdR
CBThtgg89QmN9WPTfVhwB6b4vejB7kIiIpOPyJVkaio6lVe8Ewhl064fnGHwXm39
vPy0ZVAB96oaKaki6qi1k7jhCAMpl/vXf1RDe5PaEKPwp3Lr81BlY6dcTPbjxkFP
Uw+uC3iRQnT8msSqA1vnhbDl9w6jfmuxX45Eo9NWGz0hDCpZNOEt2oSo/OcXTH4k
c91FiW8Qv9uZX2tV4VSqFQgVPfneA+OWXMpjMg6kfK3jOJ5cZwmFGAa8ByqWACH/
U9OODYQCsyX5ZM11g7MOt7Iv+YSU8OA0We8KDN4cRZobrCHF0Txp3ZTSPjb/xHE3
9nUM50I=
=a6Go
-----END PGP SIGNATURE-----
Merge tag 'v5.12-rc4' into next
Sync up with the mainline to bring in newest APIs.
The first thing the Cypress driver does when starting
up is to try a soft reset. This is the first point where
the driver SPI/I2C communication can fail, so put out some
nice debug text:
cyttsp-spi spi2.0: failed to send soft reset
Instead of just:
cyttsp-spi: probe of spi2.0 failed with error -5
This is more helpful.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210322221349.1116666-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device's hardware reset pin is only required if the platform
must be able to update the device's firmware.
As such, demote the reset GPIO to optional in support of devices
that ship with pre-programmed firmware and don't route the reset
pin back to the SoC.
In that case, the 'fw_file' attribute is hidden because there is
no way to open the bootloader. The logic is extended to the case
in which the device does not advertise bootloader support in the
first place.
Last but not least, remove the hardware reset performed at probe
because there is no reason to reset the device manually. A power
on reset function already ensures a clean reset at start-up.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210323021006.367-1-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that the helper functions have been moved to drivers/input/ so
that all input devices may use them, the introductory comments can
be updated to remove any implication that the helper functions are
solely limited to touchscreens.
This patch also scrubs any remaining use of 'DT' since there isn't
any actual dependency on OF. A minor spelling error is resolved as
well ('setups' -> 'sets up').
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210301234928.4298-3-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Some devices outside of drivers/input/touchscreen/ can still make
use of the touchscreen helper functions. Therefore, it was agreed
in [1] to move them outside of drivers/input/touchscreen/ so that
other devices can call them without INPUT_TOUCHSCREEN being set.
As part of this change, 'of' is dropped from the filename because
the helpers no longer actually use OF. No changes are made to the
file contents whatsoever.
Based on the feedback in [2], the corresponding binding documents
(touchscreen.yaml and touchscreen.txt) are left in their original
locations.
[1] https://patchwork.kernel.org/patch/11924029/
[2] https://patchwork.kernel.org/patch/12042037/
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210301234928.4298-2-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of forcing interrupt trigger to "level low" rely on the
platform to set it up according to how it is wired on the given
board.
Reviewed-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20210321220043.318239-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bootloader can be closed using the 'execute' command (0x02) or
hardware reset. Rather than using the former option for successful
firmware update procedures and reserving the latter for recovering
the device upon failure, simply use hardware reset for all cases.
The post-bootloader initialization delay increases marginally when
triggered by a hardware reset, so increase the wait time to ensure
the device does not subsequently fail to respond.
As part of this change, refactor the return path to avoid an extra
assignment and to make the logic a bit smaller.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-6-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The vendor-assigned firmware project number is restricted to the
generic project number (15); however the vendor may assign other
project numbers to specific applications and customers.
These custom project numbers may be based on forwards-compatible
firmware revision 1.x. However, the driver unnecessarily rejects
anything older than firmware revision 2.0.
To support other applications, remove these unnecessarily strict
checks and enter the bootloader only for truly incompatible A000
devices.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-5-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the read-only 'fw_info' attribute which reports information
about the device's firmware in the following format:
a.b.c.d:e.f
Where:
a = Product number (e.g. 40 for IQS550)
b = Project number (e.g. 15)
c = Firmware revision (major)
d = Firmware revision (minor)
e = Customer-assigned exported file version (major)
f = Customer-assigned exported file version (minor)
As part of the corresponding rework to uses of 'bl_status', the
IQS5XX_BL_STATUS_RESET definition is dropped with 0 used in its
place instead.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-4-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Set the maximum ABS_MT_PRESSURE value and use the existing U16_MAX
definition instead of a magic number to validate ABS_MT_POSITION_X
and ABS_MT_POSITION_Y.
Also use input_set_abs_params() rather than input_abs_set_max() to
avoid having to call input_set_capability() separately.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-3-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace 'http' with 'https' and correct the spelling of the nearby
word 'datasheet'.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/20210313191236.4366-2-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We want to be able to report the input event as soon as the debounce
delay elapsed. However, the current code does not really ensure that,
as it uses the jiffies-based schedule_delayed_work() API. With a small
enough HZ value (HZ <= 100), this results in some input events being
lost, when a key is quickly pressed then released (on a human's time
scale).
Switching to hrtimers fixes this issue, and will work even on extremely
low HZ values (tested at HZ=24). This is however only possible if
reading the GPIO is possible without sleeping. If this condition is not
met, the previous approach of using a jiffies-based timer is taken.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210307222240.380583-3-paul@crapouillou.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dealing with input, timing is important; if the button should be
released in one millisecond, then it should be done in one millisecond
and not a hundred milliseconds.
Therefore, the standard timer API is not really suitable for this task.
Convert the gpio-keys driver to use a hrtimer instead of the standard
timer to address this issue.
Note that by using a hard IRQ for the hrtimer callback, we can get rid
of the spin_lock_irqsave() and spin_unlock_irqrestore().
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210307222240.380583-2-paul@crapouillou.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The input_sync() function is already called after the loop in
gpio_keys_report_state(), so it does not need to be called after each
iteration within gpio_keys_gpio_report_event().
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210307222240.380583-1-paul@crapouillou.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The for loop is just a complicate way to express a division. Replace it
by the actual division which is both simpler to understand for a human
and more efficient for a CPU to calculate.
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210316212233.50765-1-uwe@kleine-koenig.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver registers an interrupt handler in _probe, but didn't configure
them until later when the _open function is called. In between, the keypad
can fire an IRQ due to touchpad activity, which the handler ignores. This
causes the kernel to disable the interrupt, blocking the keypad from
working.
Fix this by disabling interrupts before registering the handler.
Additionally, disable them in _close, so that they're only enabled while
open.
Fixes: fc4f314618 ("Input: add TI-Nspire keypad support")
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/3383725.iizBOSrK1V@linux-e202.suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Zenbook Flip entry that was added overwrites a previous one
because of a typo:
In file included from drivers/input/serio/i8042.h:23,
from drivers/input/serio/i8042.c:131:
drivers/input/serio/i8042-x86ia64io.h:591:28: error: initialized field overwritten [-Werror=override-init]
591 | .matches = {
| ^
drivers/input/serio/i8042-x86ia64io.h:591:28: note: (near initialization for 'i8042_dmi_noselftest_table[0].matches')
Add the missing separator between the two.
Fixes: b5d6e7ab7f ("Input: i8042 - add ASUS Zenbook Flip to noselftest list")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Link: https://lore.kernel.org/r/20210323130623.2302402-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is no use for the firmware interface after getting the touch
buffer address, so release it.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
According to datasheets, chips like mXT1386 have a WAKE line, it is used
to wake the chip up from deep sleep mode before communicating with it via
the I2C-compatible interface.
If the WAKE line is connected to a GPIO line, the line must be asserted
25 ms before the host attempts to communicate with the controller. If the
WAKE line is connected to the SCL pin, the controller will send a NACK on
the first attempt to address it, the host must then retry 25 ms later.
Implement the wake-up methods in the driver. Touchscreen now works
properly on devices like Acer A500 tablet, fixing problems like this:
atmel_mxt_ts 0-004c: __mxt_read_reg: i2c transfer failed (-121)
atmel_mxt_ts 0-004c: mxt_bootloader_read: i2c recv failed (-121)
atmel_mxt_ts 0-004c: Trying alternate bootloader address
atmel_mxt_ts 0-004c: mxt_bootloader_read: i2c recv failed (-121)
atmel_mxt_ts: probe of 0-004c failed with error -121
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210302102158.10533-3-digetx@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is error from cppcheck tool.
"Shifting signed 32-bit value by 31 bits is undefined behaviour errors"
Signed-off-by: edison.jiang <jiangzhipeng@yulong.com>
Link: https://lore.kernel.org/r/20210316153150.1207-1-jzp0409@163.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver data for the data interface has already been set by
usb_driver_claim_interface() so drop the subsequent redundant
assignment.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210318155525.22496-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210314210951.645783-2-andy.shevchenko@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This converts the driver to use GPIO descriptors.
Note that it now uses logical polarity and thus nagation has been dropped.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20210314210951.645783-1-andy.shevchenko@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Actions Semi ATC260x PMICs are able to manage an onkey button.
This driver exposes the ATC260x onkey as an input device. It can also
be configured to force a system reset on a long key-press with an
adjustable duration.
The currently supported chip variants are ATC2603C and ATC2609A.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
In case of error, the function devm_platform_ioremap_resource()
returns ERR_PTR() and never returns NULL. The NULL test in the
return value check should be replaced with IS_ERR().
Fixes: 3bdffa8ffb ("Input: Add N64 controller driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Lauri Kasanen <cand@gmx.com>
Link: https://lore.kernel.org/r/20210308122856.2177071-1-weiyongjun1@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Newer controllers, such as Voxel, Delbin, Magple, Bobba and others, do not
need to be reset after issuing power-on command, and skipping reset saves
at least 100ms from resume time.
Note that if first attempt of re-initializing device fails we will not be
skipping reset on the subsequent ones.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20210226073537.4926-1-jingle.wu@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If the device is stuck in bootloader (maybe due to blank or corrupted
application firmware) it won't answer a query for the firmware version.
Fall back to returning the bootloader version in that case.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20210125182527.1225245-4-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Factor out the vendor data i2c request handling to make it reusable
for other functions. Also don't cache the model and firmware version
string in the device private data as we never use the cached version,
but always read from the device.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20210125182527.1225245-3-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Split out the multitouch event handling into its own function to allow other
events to be handled in the IRQ handler without disturbing the MT handling.
Now that things are separated a bit more, stop treating vendor data requests
special by cehcking for a locked mutex, but just look at the event ID to
figure out if the message is a MT report or a vendor data query reply.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20210125182527.1225245-2-l.stach@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touch coordinate register contains the following:
byte 3 byte 2 byte 1
+--------+--------+ +-----------------+ +-----------------+
| | | | | | |
| X[3:0] | Y[3:0] | | Y[11:4] | | X[11:4] |
| | | | | | |
+--------+--------+ +-----------------+ +-----------------+
Bytes 2 and 1 need to be shifted left by 4 bits, the least significant
nibble of each is stored in byte 3. Currently they are only
being shifted by 3 causing the reported coordinates to be incorrect.
This matches downstream examples, and has been confirmed on my
device (OnePlus 7 Pro).
Fixes: 0145a7141e ("Input: add support for the Samsung S6SY761 touchscreen")
Signed-off-by: Caleb Connolly <caleb@connolly.tech>
Reviewed-by: Andi Shyti <andi@etezian.org>
Link: https://lore.kernel.org/r/20210305185710.225168-1-caleb@connolly.tech
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
"Mostly existing driver fixes plus a new driver for game controllers
directly connected to Nintendo 64, and an enhancement for keyboards
driven by Chrome OS EC to communicate layout of the top row to
userspace"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (47 commits)
Input: st1232 - fix NORMAL vs. IDLE state handling
Input: aiptek - convert sysfs sprintf/snprintf family to sysfs_emit
Input: alps - fix spelling of "positive"
ARM: dts: cros-ec-keyboard: Use keymap macros
dt-bindings: input: Fix the keymap for LOCK key
dt-bindings: input: Create macros for cros-ec keymap
Input: cros-ec-keyb - expose function row physical map to userspace
dt-bindings: input: cros-ec-keyb: Add a new property describing top row
Input: applespi - fix occasional crc errors under load.
Input: applespi - don't wait for responses to commands indefinitely.
Input: st1232 - add IDLE state as ready condition
Input: zinitix - fix return type of zinitix_init_touch()
Input: i8042 - add ASUS Zenbook Flip to noselftest list
Input: add missing dependencies on CONFIG_HAS_IOMEM
Input: joydev - prevent potential read overflow in ioctl
Input: elo - fix an error code in elo_connect()
Input: xpad - add support for PowerA Enhanced Wired Controller for Xbox Series X|S
Input: sur40 - fix an error code in sur40_probe()
Input: elants_i2c - detect enum overflow
Input: zinitix - remove unneeded semicolon
...
NORMAL (0x0) and IDLE (0x4) are really two different states. Hence you
cannot check for both using a bitmask, as that checks for IDLE only,
breaking operation for devices that are in NORMAL state.
Fix the wait function to report either state as ready.
Fixes: 6524d8eac2 ("Input: st1232 - add IDLE state as ready condition")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Michael Tretter <m.tretter@pengutronix.de>
Link: https://lore.kernel.org/r/20210223090201.1430542-1-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The top-row keys in a keyboard usually have dual functionalities.
E.g. A function key "F1" is also an action key "Browser back".
Therefore, when an application receives an action key code from
a top-row key press, the application needs to know how to correlate
the action key code with the function key code and do the conversion
whenever necessary.
Since the userpace already knows the key scanlines (row/column)
associated with a received key code. Essentially, the userspace only
needs a mapping between the key row/column and the matching physical
location in the top row.
So, enhance the cros-ec-keyb driver to create such a mapping
and expose it to userspace in the form of a function_row_physmap
attribute. The attribute would be a space separated ordered list of
row/column codes for the keys in the function row, in a left-to-right
order.
The attribute will only be present when the device has a custom design
for the top-row keys.
Signed-off-by: Philip Chen <philipchen@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210115122412.v7.2.I6542d7d9d0b246e7079bb16b41e697b2ac4b4e39@changeid
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmAppPgeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGeXYH/imZPBd4A1jIMehN
5HV2A53Z+MXmmaMuGj9X1KV6vsf55/xB+IhOoFdtRAIsO8c2yYSCO8i4+4R0XfYA
+/YFJeq672rojQnmh6XbpR8dugaAV7CUHy6n7KDsyvtT6EOCpwFSwkOb4X3tBRX6
TlYgm2d/xgV/wRHSgLVugK0MdFCLMAnyb7mkPfar9QrMgG1BiDKLq07xmwnS23On
TkqpJ9yZ/rJpUrrUqQYPShSO/FmA+fSfWs0CDv7EIrJ40LUScD6PZxSHWTIHtjLk
E4jFda6wuqLRVWsBwaBzUIdD0zk7X5quHRzEpbC5ga16SK6yrWvE5YJJXCguIEuZ
f3FMRYs=
=CAjn
-----END PGP SIGNATURE-----
Merge tag 'v5.11' into next
Merge with mainline to get latest APIs and device tree bindings.
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----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=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
A relatively calm release at this time, and no massive code changes
are found in the stats, while a wide range of code refactoring and
cleanup have been done.
Note that this update includes the tree-wide trivial changes for
dropping the return value from ISA remove callbacks, too.
Below lists up some highlight:
* ALSA Core:
- Support for the software jack injection via debugfs
- Fixes for sync_stop PCM operations
* HD-audio and USB-audio:
- A few usual HD-audio device quirks
- Updates for Tegra HD-audio
- More quirks for Pioneer and other USB-audio devices
- Stricter state checks at USB-audio disconnection
* ASoC:
- Continued code refactoring, cleanup and fixes in ASoC core API
- A KUnit testsuite for the topology code
- Lots of ASoC Intel driver Realtek codec updates, quirk additions and
fixes
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers
* Others:
- Drop return value from ISA driver remove callback
- Cleanup with DIV_ROUND_UP() macro
- FireWire updates, HDSP output loopback support
-----BEGIN PGP SIGNATURE-----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=QgvS
-----END PGP SIGNATURE-----
Merge tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"A relatively calm release at this time, and no massive code changes
are found in the stats, while a wide range of code refactoring and
cleanup have been done.
Note that this update includes the tree-wide trivial changes for
dropping the return value from ISA remove callbacks, too.
Below lists up some highlight:
ALSA Core:
- Support for the software jack injection via debugfs
- Fixes for sync_stop PCM operations
HD-audio and USB-audio:
- A few usual HD-audio device quirks
- Updates for Tegra HD-audio
- More quirks for Pioneer and other USB-audio devices
- Stricter state checks at USB-audio disconnection
ASoC:
- Continued code refactoring, cleanup and fixes in ASoC core API
- A KUnit testsuite for the topology code
- Lots of ASoC Intel driver Realtek codec updates, quirk additions
and fixes
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers
Others:
- Drop return value from ISA driver remove callback
- Cleanup with DIV_ROUND_UP() macro
- FireWire updates, HDSP output loopback support"
* tag 'sound-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (322 commits)
ALSA: hda: intel-dsp-config: add Alder Lake support
ASoC: soc-pcm: fix hw param limits calculation for multi-DAI
ASoC: Intel: bytcr_rt5640: Add quirk for the Acer One S1002 tablet
ASoC: Intel: bytcr_rt5651: Add quirk for the Jumper EZpad 7 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Voyo Winpad A15 tablet
ASoC: Intel: bytcr_rt5640: Add quirk for the Estar Beauty HD MID 7316R tablet
ASoC: soc-pcm: fix hwparams min/max init for dpcm
ALSA: hda/realtek: Quirk for HP Spectre x360 14 amp setup
ALSA: usb-audio: Add implicit fb quirk for BOSS GP-10
ALSA: hda: Add another CometLake-H PCI ID
ASoC: soc-pcm: add soc_pcm_hw_update_format()
ASoC: soc-pcm: add soc_pcm_hw_update_chan()
ASoC: soc-pcm: add soc_pcm_hw_update_rate()
ASoC: wm_adsp: Remove unused control callback structure
ASoC: SOF: relax ABI checks and avoid unnecessary warnings
ASoC: codecs: lpass-tx-macro: add dapm widgets and route
ASoC: codecs: lpass-tx-macro: add support for lpass tx macro
ASoC: qcom: dt-bindings: add bindings for lpass tx macro codec
ASoC: codecs: lpass-rx-macro: add iir widgets
ASoC: codecs: lpass-rx-macro: add dapm widgets and route
...
Here is the big set of tty/serial driver changes for 5.12-rc1.
Nothing huge, just lots of good cleanups and additions:
- Your n_tty line discipline cleanups
- vt core cleanups and reworks to make the code more "modern"
- stm32 driver additions
- tty led support added to the tty core and led layer
- minor serial driver fixups and additions
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYCqgqw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymJYQCgnxHmkhzJ2VarTDR3cWm1gu0NU7AAoNe5wWUh
4TQbhB9LSNo78HnIVze0
=Chcg
-----END PGP SIGNATURE-----
Merge tag 'tty-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the big set of tty/serial driver changes for 5.12-rc1.
Nothing huge, just lots of good cleanups and additions:
- n_tty line discipline cleanups
- vt core cleanups and reworks to make the code more "modern"
- stm32 driver additions
- tty led support added to the tty core and led layer
- minor serial driver fixups and additions
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (54 commits)
serial: core: Remove BUG_ON(in_interrupt()) check
vt_ioctl: Remove in_interrupt() check
dt-bindings: serial: imx: Switch to my personal address
vt: keyboard, use new API for keyboard_tasklet
serial: stm32: improve platform_get_irq condition handling in init_port
serial: ifx6x60: Remove driver for deprecated platform
tty: fix up iterate_tty_read() EOVERFLOW handling
tty: fix up hung_up_tty_read() conversion
tty: fix up hung_up_tty_write() conversion
tty: teach the n_tty ICANON case about the new "cookie continuations" too
tty: teach n_tty line discipline about the new "cookie continuations"
tty: clean up legacy leftovers from n_tty line discipline
tty: implement read_iter
tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer
serial: remove sirf prima/atlas driver
serial: mxs-auart: Remove <asm/cacheflush.h>
serial: mxs-auart: Remove serial_mxs_probe_dt()
serial: fsl_lpuart: Use of_device_get_match_data()
dt-bindings: serial: renesas,hscif: Add r8a779a0 support
tty: serial: Drop unused efm32 serial driver
...
For some reason, when the system is under heavy CPU load, the read
following the write sometimes occurs unusually quickly, resulting in
the read data not being quite ready and hence a bad packet getting read.
Adding another delay after reading the status message appears to fix
this.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Link: https://lore.kernel.org/r/20210217190718.11035-2-ronald@innovation.ch
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The response to a command may never arrive or it may be corrupted (and
hence dropped) for some reason. While exceedingly rare, when it did
happen it blocked all further commands. One way to fix this was to
do a suspend/resume. However, recovering automatically seems like a
nicer option. Hence this puts a time limit (1 sec) on how long we're
willing to wait for a response, after which we assume it got lost.
Signed-off-by: Ronald Tschalär <ronald@innovation.ch>
Link: https://lore.kernel.org/r/20210217190718.11035-1-ronald@innovation.ch
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The st1232 can switch from NORMAL to IDLE state after the configured
idle time (by default 8 s). If the st1232 is not reset during probe, it
might already be ready but in IDLE state. Since it does not enter NORMAL
state in this case, probe fails.
Fix the wait function to report the IDLE state as ready, too.
Fixes: f605be6a57 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Link: https://lore.kernel.org/r/20210219110556.1858969-1-m.tretter@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
zinitix_init_touch() returns error code or 0 for success and therefore
return type must be int, not bool.
Fixes: 26822652c8 ("Input: add zinitix touchscreen driver")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Link: https://lore.kernel.org/r/YC8z2bXc3Oy8pABa@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After commit 77b425399f ("Input: i8042 - use chassis info to skip
selftest on Asus laptops"), all modern Asus laptops have the i8042
selftest disabled. It has done by using chassys type "10" (laptop).
The Asus Zenbook Flip suffers from similar suspend/resume issues, but
it _sometimes_ work and sometimes it doesn't. Setting noselftest makes
it work reliably. In this case, we need to add chassis type "31"
(convertible) in order to avoid selftest in this device.
Reported-by: Ludvig Norgren Guldhag <ludvigng@gmail.com>
Signed-off-by: Marcos Paulo de Souza <mpdesouza@suse.com>
Link: https://lore.kernel.org/r/20210219164638.761-1-mpdesouza@suse.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_ioremap_resource() is only guaranteed to be present if
CONFIG_HAS_IOMEM is set.
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/YCyauGyqxut69JNz@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The problem here is that "len" might be less than "joydev->nabs" so the
loops which verfy abspam[i] and keypam[] might read beyond the buffer.
Fixes: 999b874f4a ("Input: joydev - validate axis/button maps before clobbering current ones")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YCyzR8WvFRw4HWw6@mwanda
[dtor: additional check for len being even in joydev_handle_JSIOCSBTNMAP]
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If elo_setup_10() fails then this should return an error code instead
of success.
Fixes: fae3006e4b ("Input: elo - add support for non-pressure-sensitive touchscreens")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YBKFd5CvDu+jVmfW@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Another quiet release in terms of features, though several of the
drivers got quite a bit of work and there were a lot of general changes
resulting from Morimoto-san's ongoing cleanup work.
- As ever, lots of hard work by Morimoto-san cleaning up the code and
making it more consistent.
- Many improvements in the Intel drivers including a wide range of
quirks and bug fixes.
- A KUnit testsuite for the topology code.
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmAtZ7cACgkQJNaLcl1U
h9DD5Af/eeERQ2uVOqtw0If+XL1xRYe6RewgDoNcO/l/5WxBLrBH6NbEf0OwNJeg
vzZAkUBtxmx6XiW2M/h+4ucW1OPcg5IzxIWTHfGDMlKIxzb0jgWugRnJ7sdTnOs3
c+QHnvuOT7QzZBviAIkc5uZ5thAImYF8zDyKoGF5llztmnBYymtgpnvnRNZGM0ou
76oUzSvkCFI2b0Yf6bpGok2nBVlOu82HSHOUKjXVWk+LAeiivlYGOEZpdIKEe3S8
u6atQJ29XRr52Yuc2z4xnFQTW1cIDlwj2Fk5x/z8hX+5nRhNSGuIv1l5m7TfBj3e
mCO9cltKZxly0NXysgekn95JHwwwkA==
=MJSb
-----END PGP SIGNATURE-----
Merge tag 'asoc-v5.12' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v5.12
Another quiet release in terms of features, though several of the
drivers got quite a bit of work and there were a lot of general changes
resulting from Morimoto-san's ongoing cleanup work.
- As ever, lots of hard work by Morimoto-san cleaning up the code and
making it more consistent.
- Many improvements in the Intel drivers including a wide range of
quirks and bug fixes.
- A KUnit testsuite for the topology code.
- Support for Ingenic JZ4760(B), Intel AlderLake-P, DT configured
nVidia cards, Qualcomm lpass-rx-macro and lpass-tx-macro
- Removal of obsolete SIRF prima/atlas, Txx9 and ZTE zx drivers.
If v4l2_ctrl_handler_setup() fails then probe() should return an error
code instead of returning success.
Fixes: cee1e3e2ef ("media: add video control handlers using V4L2 control framework")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YBKFkbATXa5fA3xj@mwanda
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If an enum value were to get added without updating this switch
statement, the unreachable() annotation would trigger undefined
behavior, causing execution to fall through the end of the function,
into the next one.
Make the error handling more robust for an unexpected enum value, by
doing BUG() instead of unreachable().
Fixes the following objtool warning:
drivers/input/touchscreen/elants_i2c.o: warning: objtool: elants_i2c_initialize() falls through to next function elants_i2c_resume()
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Reviewed-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Link: https://lore.kernel.org/r/59e2e82d1e40df11ab38874c03556a31c6b2f484.1612974132.git.jpoimboe@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The driver core ignores the return value of struct bus_type::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct locomo_driver::remove return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea and ensures future
users behave accordingly.
Link: https://lore.kernel.org/r/20201126110140.2021758-1-u.kleine-koenig@pengutronix.de
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
The driver core ignores the return value of struct device_driver::remove
because there is only little that can be done. To simplify the quest to
make this function return void, let struct sa1111_driver::remove return
void, too. All users already unconditionally return 0, this commit makes
it obvious that returning an error code is a bad idea and ensures future
users behave accordingly.
Link: https://lore.kernel.org/r/20201126114724.2028511-1-u.kleine-koenig@pengutronix.de
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
If execution jumps to the err_kfree label, error_bl is evaluated
before it is initialized. Fix this by initializing it to zero.
Fixes: 2539da6677 ("Input: iqs5xx - preserve bootloader errors")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611592500-32209-1-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver core ignores the return value of the remove callback, so
don't give isa drivers the chance to provide a value.
Adapt all isa_drivers with a remove callbacks accordingly; they all
return 0 unconditionally anyhow.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/net/can/sja1000/tscan1.c
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for drivers/i2c/
Reviewed-by: Takashi Iway <tiwai@suse.de> # for sound/
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for drivers/media/
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210122092449.426097-4-uwe@kleine-koenig.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds support for the four built-in controller
ports on the Nintendo 64 console. The N64 controller
includes an analog stick, a d-pad, and several buttons.
No module support as the target has only 8mb ram.
Signed-off-by: Lauri Kasanen <cand@gmx.com>
Link: https://lore.kernel.org/r/20210115133408.0acd70163b582b77ad0a029b@gmx.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Avoid placing the device in suspend mode (from which it cannot
generate interrupts) if it is defined as a wake-up source. The
device is still permitted to enter a low-power sensing mode on
its own.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-11-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After the device is initialized, it runs ATI (calibration) during
which it cannot readily respond to I2C communication. To keep the
open and close callbacks from writing to the device too soon, the
driver waits 100 ms before returning from probe.
The vendor reports that ATI may actually take up to 250 ms to run
(including margin), so increase the delay accordingly. Update the
comments to clarify the reason for the delay as well.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-9-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of relying on firmware to enable important register fields
and performing read-modify-write operations to additionally enable
the fields the driver cares about, it's much simpler just to write
all of the pertinent fields explicitly.
This avoids an unnecessary register read operation at start-up and
makes way for the iqs5xx_read_byte() helper to be dropped.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-8-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The present implementation manipulates axis swap and inversion fields
in the device to more or less duplicate what touchscreen_report_pos()
does. The resulting logic is convoluted and difficult to follow.
Instead report the maximum X and Y coordinates in earnest as they are
read from the device, then let touchscreen_parse_properties() fix the
axes up as necessary. Finally, use touchscreen_report_pos() to report
the transformed coordinates.
Last but not least, the maximum X and Y coordinates are not functions
of the number of rows/columns that comprise the touch surface. Either
coordinate is simply limited to 1 below what is reported for absolute
X or Y coordinates when no fingers are present (0xFFFF).
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-7-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The device may be inadvertently reset during runtime in the event
of ESD strike, etc. To protect against this case, acknowledge the
SHOW_RESET interrupt and re-initialize the device.
To facilitate this change, expand the range of registers that are
read in the interrupt handler to include the system status fields.
Also, update the unrelated (but nearby) SUSPEND register field to
use the BIT() macro. The remaining register fields are cleaned up
in another patch.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-6-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The bootloader NAK's all I2C communication after the first 64-byte
bulk write if the bus frequency is equal to 400 kHz. This prevents
the platform from pushing updated firmware to the device.
The vendor's USB bootloader programming dongle appears to insert a
delay between the "open" command and the first 64-byte bulk write.
Adding a similar delay to the driver seems to eliminate the issue.
Furthermore, the dongle does not access the bootloader immediately
after powering up the device. Follow suit by adding a delay before
the "open" command to avoid wasted retries at 400 kHz.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-4-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After user space writes the fw_file attribute to push new firmware
to the device, the driver calls iqs5xx_dev_init() to re-initialize
the device with the updated firmware or recover the device in case
the update failed.
In the case of the latter, however, iqs5xx_fw_file_write() returns
zero (success) so long as iqs5xx_dev_init() does not fail, and any
error encountered during the update process is lost. Solve this by
saving the error before calling iqs5xx_dev_init().
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-3-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Copyrights are generally followed by the name of a person or a
company (i.e. the copyright holder) but that was not done here.
Fix this by squashing the 'copyright' and 'author' lines.
Also, trim some leading whitespace ahead of the parameters for
the fw_file_store() function and re-align them for readability.
Signed-off-by: Jeff LaBundy <jeff@labundy.com>
Link: https://lore.kernel.org/r/1611002626-5889-2-git-send-email-jeff@labundy.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There is a fork of this driver on GitHub [0] that has been updated
with new device IDs.
Merge those into the mainline driver, so the out-of-tree fork is not
needed for users of those devices anymore.
[0] https://github.com/paroj/xpad
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Link: https://lore.kernel.org/r/20210121142523.1b6b050f@rechenknecht2k11
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add ELAN KTF3624 touchscreen support to the elants_i2c driver.
The eKTF3624 TS is found on a series of ASUS Transformer tablet devices,
Nexus 7 tablet and etc. The firmware interface of eKTF3624 is nearly
identical to eKTH3500, which is already supported by the driver.
The minor differences of the firmware interface are now handled by
the driver. The eKTF3624 support was tested on ASUS Transformer TF700T,
TF300T and Nexus 7 tablets.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Link: https://lore.kernel.org/r/20210124195414.27333-1-digetx@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes both the "splice/sendfile to a tty" and "splice/sendfile from a
tty" regression from 5.10.
* 'tty-splice' of git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux:
tty: teach the n_tty ICANON case about the new "cookie continuations" too
tty: teach n_tty line discipline about the new "cookie continuations"
tty: clean up legacy leftovers from n_tty line discipline
tty: implement read_iter
tty: convert tty_ldisc_ops 'read()' function to take a kernel pointer
tty: implement write_iter
Convert multiple full duplex transfers in to a single transfer to reduce
CPU load.
Current driver version support following filtering modes:
- ads7846_no_filter() - not filtered
- ads7846_debounce_filter() - driver specific debounce filter
- pdata->filter - platform specific debounce filter (do any platform
provides such filter?)
Without filter this HW is not really usable, since the physic of
resistive touchscreen can provide some bounce effects. With driver internal
filter, we have constant amount of retries + debounce retries if some anomaly
was detected.
High amount of tiny SPI transfers is the primer reason of high CPU load
and interrupt frequency.
This patch create one SPI transfer with all fields and not optional retires. If
bounce anomaly was detected, we will make more transfer if needed.
Without this patch, we will get about 10% CPU load on iMX6S on pen-down event.
For example by holding stylus on the screen.
With this patch, depending in the amount of retries, the CPU load will
be 1% with "ti,debounce-rep = <3>".
One buffer transfer allows us to use PIO FIFO or DMA engine, depending
on the platform.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-3-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The tty line discipline .read() function was passed the final user
pointer destination as an argument, which doesn't match the 'write()'
function, and makes it very inconvenient to do a splice method for
ttys.
This is a conversion to use a kernel buffer instead.
NOTE! It does this by passing the tty line discipline ->read() function
an additional "cookie" to fill in, and an offset into the cookie data.
The line discipline can fill in the cookie data with its own private
information, and then the reader will repeat the read until either the
cookie is cleared or it runs out of data.
The only real user of this is N_HDLC, which can use this to handle big
packets, even if the kernel buffer is smaller than the whole packet.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/stmpe-ts.c:82: warning: Function parameter or member 'prop' not described in 'stmpe_touch'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210114152323.2382283-6-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/surface3_spi.c: In function ‘surface3_spi_process_touch’:
drivers/input/touchscreen/surface3_spi.c:97:6: warning: variable ‘timestamp’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Link: https://lore.kernel.org/r/20210114152323.2382283-5-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/usbtouchscreen.c: In function ‘nexio_read_data’:
drivers/input/touchscreen/usbtouchscreen.c:1052:50: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210114152323.2382283-4-lee.jones@linaro.org
[dtor: log error code as well]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Dmitry requested to keep these around for the purposes of documentation.
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/melfas_mip4.c: In function ‘mip4_report_touch’:
drivers/input/touchscreen/melfas_mip4.c:474:5: warning: variable ‘size’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/melfas_mip4.c:472:5: warning: variable ‘pressure_stage’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/melfas_mip4.c:469:7: warning: variable ‘palm’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/melfas_mip4.c:468:7: warning: variable ‘hover’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210114152323.2382283-3-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/mouse/synaptics.c: In function ‘synaptics_process_packet’:
drivers/input/mouse/synaptics.c:1110:6: warning: suggest braces around empty body in an ‘if’ statement [-Wempty-body]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20210114152323.2382283-2-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are still missing handling for errata i689 related issues for the
case where we never see a key up interrupt for the last pressed key.
To fix the issue, we must scan the key state again after the keyboard
controller has idled to check if a key up event was missed. This is
described in the omap4 silicon errata documentation for Errata ID i689
"1.32 Keyboard Key Up Event Can Be Missed":
"When a key is released for a time shorter than the debounce time,
in-between 2 key press (KP1 and KP2), the keyboard state machine will go
to idle mode and will never detect the key release (after KP1, and also
after KP2), and thus will never generate a new IRQ indicating the key
release."
We can use PM runtime autosuspend features to check the keyboard state
after it enters idle.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/X/vrygoBxzGyXhfc@atomide.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Implement PM runtime autosuspend support to prepare for adding handling to
clear stuck last pressed key in the following patches. The hardware has
support for autoidle and can wake up to keypress events.
Let's also update omap4_keypad_probe() to use dev instead of &pdev->dev
since we already have it from the earlier changes.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/X/vqCs5/EDURprAJ@atomide.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's move rest of the key scanning code to omap4_keypad_scan_keys().
We will use omap4_keypad_scan_keys() also for implementing errata
handling to clear the stuck last key in the following patch.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210110190529.46135-4-tony@atomide.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Because of errata i689 the keyboard can idle with state where no key
up interrupts are seen until after the next key press.
This means we need to first check for any lost key up events before
scanning for new down events.
For example, rapidly pressing shift-shift-j can sometimes produce a J
instead of j. Let's fix the issue by scanning the keyboard in two
phases. First we scan for any key up events that we may have missed,
and then we scan for key down events.
Let's also simplify things with for_each_set_bit() as suggested by
Dmitry Torokhov <dmitry.torokhov@gmail.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210110190529.46135-3-tony@atomide.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are not using the long events and they produce extra interrupts.
Let's not enable them at all.
Note that also the v3.0.8 Linux Android kernel has long interrupts
disabled.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/r/20210110190529.46135-2-tony@atomide.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that input core supports devres-managed input devices we can clean
up this driver a bit.
Link: https://lore.kernel.org/r/X/qfJKiM21uyksYl@google.com
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Goodix GT9286 is a capacitive touch sensor IC based on GT1x.
This chip can be found on a number of smartphones, including the
F(x)tec Pro 1 and the Elephone U.
This has been tested on F(x)Tec Pro1 (MSM8998).
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@somainline.org>
Link: https://lore.kernel.org/r/20210109135512.149032-2-angelogioacchino.delregno@somainline.org
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ILI251x seems to report pressure information in the 5th byte of
each per-finger touch data element. On the available hardware, this
information has the values ranging from 0x0 to 0xa, which is also
matching the downstream example code. Report pressure information
on the ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20201224071238.160098-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
g++ reports
drivers/input/serio/i8042-x86ia64io.h:225:3: error: ‘.matches’ designator used multiple times in the same initializer list
C99 semantics is that last duplicated initialiser wins,
so DMI entry gets overwritten.
Fixes: a48491c65b ("Input: i8042 - add ByteSpeed touchpad to noloop table")
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Acked-by: Po-Hsu Lin <po-hsu.lin@canonical.com>
Link: https://lore.kernel.org/r/20201228072335.GA27766@localhost.localdomain
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to the st1232 datasheet, the host has to wait for the device
to change into Normal state before accessing registers other than the
Status Register.
If the reset GPIO is wired, the device is powered on during driver
probe, just before reading the resolution. However, the latter may
happen before the device is ready, leading to a probe failure:
st1232-ts 1-0055: Failed to read resolution: -6
Fix this by waiting until the device is ready, by trying to read the
Status Register until it indicates so, or until timeout.
On Armadillo 800 EVA, typically the first read fails with an I2C
transfer error, while the second read indicates the device is ready.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-4-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
st1232_ts_read_data() already reads ts->read_buf_len bytes (8 or 20
bytes) from the touchscreen controller. This was fine when it was used
to read touch point coordinates only, but is overkill for reading the
touchscreen resolution, which just needs 3 bytes.
Optimize transfers by passing the wanted number of bytes.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-3-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Before, the maximum coordinates were fixed to (799, 479) or (319, 479),
depending on touchscreen controller type. The driver was changed to
read the actual values from the touchscreen controller, but did not take
into account the returned values are not the maximum coordinates, but
the touchscreen resolution (e.g. 800 and 480).
Fix this by subtracting 1.
Fixes: 3a54a21541 ("Input: st1232 - add support resolution reading")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201229162601.2154566-2-geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_platform_ioremap_resource() depends on CONFIG_HAS_IOMEM, so let's add
it to the dependencies when COMPILE_TEST is enabled.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: c8834032ff ("Input: imx_keypad - add COMPILE_TEST support")
Link: https://lore.kernel.org/r/X9llpA3w1zlZCHXU@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The OF match table is only used when OF is enabled.
Fixes: cd3f609823 ("Input: new da7280 haptic driver")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Roy Im <roy.im.opensource@diasemi.com>
Link: https://lore.kernel.org/r/X9xRLVPt9eBi0CT6@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
An "if" testing for error condition has accidentally been dropped from
the code.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: cd3f609823 ("Input: new da7280 haptic driver")
Reviewed-by: Roy Im <Roy.Im.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/X9j8lGFgijzHyYZZ@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input updates from Dmitry Torokhov:
- support for inhibiting input devices at request from userspace. If a
device implements open/close methods, it can also put device into low
power state. This is needed, for example, to disable keyboard and
touchpad on convertibles when they are transitioned into tablet mode
- now that ordinary input devices can be configured for polling mode,
dedicated input polling device implementation has been removed
- GTCO tablet driver has been removed, as it used problematic custom
HID parser, devices are EOL, and there is no interest from the
manufacturer
- a new driver for Dialog DA7280 haptic chips has been introduced
- a new driver for power button on Dell Wyse 3020
- support for eKTF2132 in ektf2127 driver
- support for SC2721 and SC2730 in sc27xx-vibra driver
- enhancements for Atmel touchscreens, AD7846 touchscreens, Elan
touchpads, ADP5589, ST1232 touchscreen, TM2 touchkey drivers
- fixes and cleanups to allow clean builds with W=1
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (86 commits)
Input: da7280 - fix spelling mistake "sequemce" -> "sequence"
Input: cyapa_gen6 - fix out-of-bounds stack access
Input: sc27xx - add support for sc2730 and sc2721
dt-bindings: input: Add compatible string for SC2721 and SC2730
dt-bindings: input: Convert sc27xx-vibra.txt to json-schema
Input: stmpe - add axis inversion and swapping capability
Input: adp5589-keys - do not explicitly control IRQ for wakeup
Input: adp5589-keys - do not unconditionally configure as wakeup source
Input: ipx4xx-beeper - convert comma to semicolon
Input: parkbd - convert comma to semicolon
Input: new da7280 haptic driver
dt-bindings: input: Add document bindings for DA7280
MAINTAINERS: da7280 updates to the Dialog Semiconductor search terms
Input: elantech - fix protocol errors for some trackpoints in SMBus mode
Input: elan_i2c - add new trackpoint report type 0x5F
Input: elants - document some registers and values
Input: atmel_mxt_ts - simplify the return expression of mxt_send_bootloader_cmd()
Input: imx_keypad - add COMPILE_TEST support
Input: applespi - use new structure for SPI transfer delays
Input: synaptics-rmi4 - use new structure for SPI transfer delays
...
The big change this release has been some excellent work from Lukas
Wunner which closes a bunch of holes in the cleanup paths for drivers,
mainly introduced as a result of devm conversions causing bad
interactions with the support SPI has for allocating the bus and driver
data together. Together with some of the other work done it feels like
we've turned the corner on several long standing pain points with the
API.
- Many cleanups around probe/remove and error handling from Lukas
Wunner and Uwe Kleine-König, and further fixes around PM from Zhang
Qilong.
- Provide a mask for which bits of the mode can safely be configured by
drivers and use that to fix an issue with the ADS7846 driver.
- Documentation of the expected interactions between SPI and GPIO level
chip select polarity configuration from H. Nikolaus Schaller,
hopefully we're pretty much at the end of sorting out the
interactions there. Thanks to Nikolaus, Sven Van Asbroeck and Linus
Walleij for this.
- DMA support for Allwinner sun6i controllers.
- Support for Canaan K210 Designware implementations and Intel Adler Lake.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAl/Xeg4ACgkQJNaLcl1U
h9BbXQf8DwmtP/biVsB0yxag11Ac9xxDL2OdMXia/DBQZsVSxqGld4l7Bwl8CMVi
TISCmzO1f53l3KZK5wu1C5mV8tXgCu4zrsPErEsrK2V2+s+4lWy10MOfAHqq/lBR
L2kifZ/uoeMBaPvJqpRimM8tv2uPXPHOKsdy2G82LzMdk0OhE5p9IkL5Nc5JbKOl
X1iWTAxtUsDb8+B57AwHSMnL4R3pb/01N0PguJJ8DGol7Oj6VcDf7nh/tqvVkEot
Ku731oCBQwBhkZKOqd7mvQAjPyoJiFPI8nofC4Bj+a1BDlr+pRcILQ4469zaIAWT
nPV6BoHTu/tVV63j8YhuamjWYAsS0g==
=ezV7
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"The big change this release has been some excellent work from Lukas
Wunner which closes a bunch of holes in the cleanup paths for drivers,
mainly introduced as a result of devm conversions causing bad
interactions with the support SPI has for allocating the bus and
driver data together.
Together with some of the other work done it feels like we've turned
the corner on several long standing pain points with the API.
Summary:
- Many cleanups around probe/remove and error handling from Lukas
Wunner and Uwe Kleine-König, and further fixes around PM from Zhang
Qilong.
- Provide a mask for which bits of the mode can safely be configured
by drivers and use that to fix an issue with the ADS7846 driver.
- Documentation of the expected interactions between SPI and GPIO
level chip select polarity configuration from H. Nikolaus Schaller,
hopefully we're pretty much at the end of sorting out the
interactions there. Thanks to Nikolaus, Sven Van Asbroeck and Linus
Walleij for this.
- DMA support for Allwinner sun6i controllers.
- Support for Canaan K210 Designware implementations and Intel Adler
Lake"
* tag 'spi-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (69 commits)
spi: dt-bindings: clarify CS behavior for spi-cs-high and gpio descriptors
spi: Limit the spi device max speed to controller's max speed
spi: spi-geni-qcom: Use the new method of gpio CS control
platform/chrome: cros_ec_spi: Drop bits_per_word assignment
platform/chrome: cros_ec_spi: Don't overwrite spi::mode
spi: dw: Add support for the Canaan K210 SoC SPI
spi: dw: Add support for 32-bits max xfer size
dt-bindings: spi: dw-apb-ssi: Add Canaan K210 SPI controller
spi: Update DT binding docs to support SiFive FU740 SoC
spi: atmel-quadspi: Fix use-after-free on unbind
spi: npcm-fiu: Disable clock in probe error path
spi: ar934x: Don't leak SPI master in probe error path
spi: mt7621: Don't leak SPI master in probe error path
spi: mt7621: Disable clock in probe error path
media: netup_unidvb: Don't leak SPI master in probe error path
spi: sc18is602: Don't leak SPI master in probe error path
spi: rb4xx: Don't leak SPI master in probe error path
spi: gpio: Don't leak SPI master in probe error path
spi: spi-mtk-nor: Don't leak SPI master in probe error path
spi: mxic: Don't leak SPI master in probe error path
...
gcc -Warray-bounds warns about a serious bug in
cyapa_pip_retrieve_data_structure:
drivers/input/mouse/cyapa_gen6.c: In function 'cyapa_pip_retrieve_data_structure.constprop':
include/linux/unaligned/access_ok.h:40:17: warning: array subscript -1 is outside array bounds of 'struct retrieve_data_struct_cmd[1]' [-Warray-bounds]
40 | *((__le16 *)p) = cpu_to_le16(val);
drivers/input/mouse/cyapa_gen6.c:569:13: note: while referencing 'cmd'
569 | } __packed cmd;
| ^~~
Apparently the '-2' was added to the pointer instead of the value,
writing garbage into the stack next to this variable.
Fixes: c2c06c41f7 ("Input: cyapa - add gen6 device module support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201026161332.3708389-1-arnd@kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
- a fix for cm109 stomping on its own control URB if it tries to toggle
buzzer immediately after userspace opens input device (found by
syzcaller)
- another fix for Raydium touchscreens that do not like splitting
command transfers
- quirks for i8042, soc_button_array, and goodix drivers to make them
work better with certain hardware.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: goodix - add upside-down quirk for Teclast X98 Pro tablet
Input: cm109 - do not stomp on control URB
Input: i8042 - add Acer laptops to the i8042 reset list
Input: cros_ec_keyb - send 'scancodes' in addition to key events
Input: soc_button_array - add Lenovo Yoga Tablet2 1051L to the dmi_use_low_level_irq list
Input: raydium_ts_i2c - do not split tx transactions
Add new compatible strings and match data to support sc2730 and sc2721
which are two varieties of SC27XX family.
Signed-off-by: Nemo Han <nemo.han@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Link: https://lore.kernel.org/r/20201117034949.47877-2-zhang.lyra@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make use of generic touchscreen_properties structure to add axis
inversion and swapping capabilities. It's configurable via devicetree
properties:
touchscreen-inverted-x
touchscreen-inverted-y
touchscreen-swapped-x-y
Signed-off-by: Stefan Riedmueller <s.riedmueller@phytec.de>
Link: https://lore.kernel.org/r/20200922093903.157232-1-s.riedmueller@phytec.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The touchscreen on the Teclast x98 Pro is also mounted upside-down in
relation to the display orientation.
Signed-off-by: Simon Beginn <linux@simonmicro.de>
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Link: https://lore.kernel.org/r/20201117004253.27A5A27EFD@localhost
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to make sure we are not stomping on the control URB that was
issued when opening the device when attempting to toggle buzzer.
To do that we need to mark it as pending in cm109_open().
Reported-and-tested-by: syzbot+150f793ac5bc18eee150@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If device is set up as a wakeup source, I2C core configures the interrupt
line as wake IRQ and PM core automatically configures it for waking up the
system on system suspend transition, so we do not have to explicitly call
enable_irq_wake() and disable_irq_wake() in suspend/resume.
Link: https://lore.kernel.org/r/20201120073920.3214492-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should not be configuring the controller as a wakeup source in the
driver, but rather rely on I2C core to mark it as such by either
instantiating as I2C_CLIENT_WAKEUP or specifying "wakeup-source" device
property.
Link: https://lore.kernel.org/r/20201120073920.3214492-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Adds support for the Dialog DA7280 LRA/ERM Haptic Driver with
multiple mode and integrated waveform memory and wideband support.
It communicates via an I2C bus to the device.
Signed-off-by: Roy Im <roy.im.opensource@diasemi.com>
Reviewed-by: Jes Sorensen <Jes.Sorensen@gmail.com>.
Link: https://lore.kernel.org/r/1e293e8c4830b09255af3b7e1721b73afaefdfa3.1606320459.git.Roy.Im@diasemi.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are some version of Elan trackpads that send incorrect data when
in SMbus mode, unless they are switched to use 0x5f reports instead of
standard 0x5e. This patch implements querying device to retrieve chips
identifying data, and switching it, when needed to the alternative
report.
Signed-off-by: Jingle Wu <jingle.wu@emc.com.tw>
Link: https://lore.kernel.org/r/20201211071531.32413-1-jingle.wu@emc.com.tw
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Tested-by: Ronald Tschalär <ronald@innovation.ch>
Reviewed-by: Ronald Tschalär <ronald@innovation.ch>
Link: https://lore.kernel.org/r/20200227124534.23399-1-sergiu.cuciurean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200227130336.27042-1-sergiu.cuciurean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In a recent change to the SPI subsystem [1], a new `delay` struct was added
to replace the `delay_usecs`. This change replaces the current
`delay_usecs` with `delay` for this driver.
The `spi_transfer_delay_exec()` function [in the SPI framework] makes sure
that both `delay_usecs` & `delay` are used (in this order to preserve
backwards compatibility).
[1] commit bebcfd272d ("spi: introduce `delay` field for
`spi_transfer` + spi_transfer_delay_exec()")
Signed-off-by: Sergiu Cuciurean <sergiu.cuciurean@analog.com>
Link: https://lore.kernel.org/r/20200228104508.15564-1-sergiu.cuciurean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of special-casing retrieval of number of X/Y electrodes based on
the firmware, let's select default values and mark registers as
non-existent on firmwares that do not support this operation.
Also mark "report rate" register as non-existent for generic firmwares
as having it set to 0 does not make sense.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Simon Budig <simon.budig@kernelconcepts.de>
Link: https://lore.kernel.org/r/X9FZFs3NZADoIhhH@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Collected patches from the two series below and associated tags so they
can be merged in one pile through the spi tree. Merry December!
SPI: https://lore.kernel.org/r/20201202214935.1114381-1-swboyd@chromium.org
cros-ec: https://lore.kernel.org/r/20201203011649.1405292-1-swboyd@chromium.org
Cc: Akash Asthana <akashast@codeaurora.org>
Cc: Simon Glass <sjg@chromium.org>
Cc: Gwendal Grignou <gwendal@chromium.org>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Alexandru M Stan <amstan@chromium.org>
Stephen Boyd (3):
platform/chrome: cros_ec_spi: Don't overwrite spi::mode
platform/chrome: cros_ec_spi: Drop bits_per_word assignment
spi: spi-geni-qcom: Use the new method of gpio CS control
drivers/platform/chrome/cros_ec_spi.c | 2 --
drivers/spi/spi-geni-qcom.c | 1 +
2 files changed, 1 insertion(+), 2 deletions(-)
base-commit: b650545978
--
https://chromeos.dev
The touchpad operates in Basic Mode by default in the Acer BIOS
setup, but some Aspire/TravelMate models require the i8042 to be
reset in order to be correctly detected.
Signed-off-by: Chris Chiu <chiu@endlessos.org>
Link: https://lore.kernel.org/r/20201207071250.15021-1-chiu@endlessos.org
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The Samsung touchkey controllers are often used with external pull-up
for the interrupt line and the I2C lines, so we might need to enable
a regulator to bring the lines into usable state. Otherwise, this might
cause spurious interrupts and reading from I2C will fail.
Implement support for a "vddio-supply" that is enabled by the
tm2-touchkey driver so that the regulator gets enabled when needed.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201203131242.44397-3-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Link: https://lore.kernel.org/linux-input/20190708123323.11943-1-huangfq.daxian@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
To let userspace know what 'scancodes' should be used in EVIOCGKEYCODE
and EVIOCSKEYCODE ioctls, we should send EV_MSC/MSC_SCAN events in
addition to EV_KEY/KEY_* events. The driver already declared MSC_SCAN
capability, so it is only matter of actually sending the events.
Link: https://lore.kernel.org/r/X87aOaSptPTvZ3nZ@google.com
Acked-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds support for the power button attached to the Embedded Controller
on a Dell Wyse 3020 "Ariel" board.
The Embedded Controller's SPI interface is actually capable sending and
receiving the PS/2 keyboard and mouse protocol data, which looks like
a good fit for a serio driver. Howerver, I don't know of any machines where
this is actually used.
My board only has a single power button and no way to connect an actual
keyboard or a mouse. Using the atkbd driver with serio would be an overkill
and would be inconvenient for the userspace. Therefore this driver
registers an input device that is only capable of reporting the power
button presses and releases.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Link: https://lore.kernel.org/r/20201201083533.1724287-3-lkundrak@v3.sk
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver has its own HID descriptor parsing code, that had and still
has several issues discovered by syzbot and other tools. Ideally we
should move the driver over to the HID subsystem, so that it uses proven
parsing code. However the devices in question are EOL, and GTCO is not
willing to extend resources for that, so let's simply remove the driver.
Note that our HID support has greatly improved over the last 10 years,
we may also consider reverting 6f8d9e26e7 ("hid-core.c: Adds all GTCO
CalComp Digitizers and InterWrite School Products to blacklist") and see
if GTCO devices actually work with normal HID drivers.
Link: https://lore.kernel.org/r/X8wbBtO5KidME17K@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the Lenovo Yoga Tablet2 1051L to the list of devices where the
ACPI AML code is poking the GPIO config register directly changing
the IRQ type to a low_level_irq, which we need to work around.
This fixes the home button on the Lenovo Yoga Tablet2 1051L not
working.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201206161245.24798-1-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Raydium device does not like splitting of tx transactions into multiple
messages - one for the register address and one for the actual data. This
results in incorrect behavior on the device side.
This change updates raydium_i2c_read and raydium_i2c_write to create
i2c_msg arrays separately and passes those arrays into raydium_i2c_xfer
which decides based on the address whether the bank switch command should
be sent. The bank switch header is still added by raydium_i2c_read and
raydium_i2c_write to ensure that all these operations are performed as part
of a single I2C transfer. It guarantees that no other transactions are
initiated to any other device on the same bus after the bank switch command
is sent.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Link: https://lore.kernel.org/r/20201205005941.1427643-1-furquan@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix for 'RETRIGEN' handling in Atmel touch controllers that was
causing lost interrupts on systems using edge-triggered interrupts, a
quirk for i8042 driver, and a couple more fixes."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: atmel_mxt_ts - fix lost interrupts
Input: xpad - support Ardwiino Controllers
Input: i8042 - add ByteSpeed touchpad to noloop table
Input: i8042 - fix error return code in i8042_setup_aux()
Input: soc_button_array - add missing include
Userspace might want to implement a policy to temporarily disregard input
from certain devices, including not treating them as wakeup sources.
An example use case is a laptop, whose keyboard can be folded under the
screen to create tablet-like experience. The user then must hold the laptop
in such a way that it is difficult to avoid pressing the keyboard keys. It
is therefore desirable to temporarily disregard input from the keyboard,
until it is folded back. This obviously is a policy which should be kept
out of the kernel, but the kernel must provide suitable means to implement
such a policy.
This patch adds a sysfs interface for exactly this purpose.
To implement the said interface it adds an "inhibited" property to struct
input_dev, and effectively creates four states a device can be in: closed
uninhibited, closed inhibited, open uninhibited, open inhibited. It also
defers calling driver's ->open() and ->close() to until they are actually
needed, e.g. it makes no sense to prepare the underlying device for
generating events (->open()) if the device is inhibited.
uninhibit
closed <------------ closed
uninhibited ------------> inhibited
| ^ inhibit | ^
1st | | 1st | |
open | | open | |
| | | |
| | last | | last
| | close | | close
v | uninhibit v |
open <------------ open
uninhibited ------------> inhibited
The top inhibit/uninhibit transition happens when users == 0.
The bottom inhibit/uninhibit transition happens when users > 0.
The left open/close transition happens when !inhibited.
The right open/close transition happens when inhibited.
Due to all transitions being serialized with dev->mutex, it is impossible
to have "diagonal" transitions between closed uninhibited and open
inhibited or between open uninhibited and closed inhibited.
No new callbacks are added to drivers, because their open() and close()
serve exactly the purpose to tell the driver to start/stop providing
events to the input core. Consequently, open() and close() - if provided
- are called in both inhibit and uninhibit paths.
Signed-off-by: Patrik Fimml <patrikf@chromium.org>
Co-developed-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Link: https://lore.kernel.org/r/20200608112211.12125-8-andrzej.p@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A helper function for drivers to decide if the device is used or not.
A lockdep check is introduced as inspecting ->users should be done under
input device's mutex.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Link: https://lore.kernel.org/r/20200608112211.12125-2-andrzej.p@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Marking main interrupt as wakeup interrupt in probe allows us to drop
custom suspend/resume methods whose only purpose was to configure interrupt
for waking up the system.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that normal input devices support polling mode, and all users of
input_polled_dev API have been converted, we can remove it.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
After commit 74d905d2d3 devices requiring the workaround for edge
triggered interrupts stopped working.
The hardware needs the quirk to be used before even proceeding to
check if the quirk is needed because mxt_acquire_irq() is called
before mxt_check_retrigen() is called and at this point pending IRQs
need to be checked, and if the workaround is not active, all
interrupts will be lost from this point.
Solve this by switching the calls around.
Reported-by: Andre Müller <andre.muller@web.de>
Tested-by: Andre Müller <andre.muller@web.de>
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes: 74d905d2d3 ("Input: atmel_mxt_ts - only read messages in mxt_acquire_irq() when necessary")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20201201123026.1416743-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix to return a negative error code from the error handling case
instead of 0 in function i8042_setup_aux(), as done elsewhere in this
function.
Fixes: f81134163f ("Input: i8042 - use platform_driver_probe")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Luo Meng <luomeng12@huawei.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201123133420.4071187-1-luomeng12@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes the following build errors:
CC [M] drivers/input/misc/soc_button_array.o
drivers/input/misc/soc_button_array.c:156:4: error: implicit declaration of function 'irq_set_irq_type' [-Werror,-Wimplicit-function-declaration]
irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
^
drivers/input/misc/soc_button_array.c:156:26: error: use of undeclared identifier 'IRQ_TYPE_LEVEL_LOW'
irq_set_irq_type(irq, IRQ_TYPE_LEVEL_LOW);
^
2 errors generated.
Fixes: 78a5b53e9f ("Input: soc_button_array - work around DSDTs which modify the irqflags")
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20201123061508.GA1009828@dtor-ws
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a
warning by replacing a /* Fall through */ comment with the new
pseudo-keyword macro fallthrough.
Notice that Clang doesn't recognize /* Fall through */ comments as
implicit fall-through markings.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/d2944854e3e118b837755abf4cbdb497662001b7.1605896060.git.gustavoars@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In omap4_keypad_probe, the patch fix several bugs.
1) pm_runtime_get_sync will increment pm usage counter even it
failed. Forgetting to pm_runtime_put_noidle will result in
reference leak.
2) In err_unmap, forget to disable runtime of device,
pm_runtime_enable will increase power disable depth. Thus a
pairing decrement is needed on the error handling path to keep
it balanced.
3) In err_pm_disable, it will call pm_runtime_put_sync twice not
one time.
To fix this we factor out code reading revision and disabling touchpad, and
drop PM reference once we are done talking to the device.
Fixes: f77621cc64 ("Input: omap-keypad - dynamically handle register offsets")
Fixes: 5ad567ffba ("Input: omap4-keypad - wire up runtime PM handling")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201120133918.2559681-1-zhangqilong3@huawei.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/mouse/vmmouse.c:99: warning: Function parameter or member 'cmd' not described in 'VMMOUSE_CMD'
drivers/input/mouse/vmmouse.c:99: warning: Function parameter or member 'in1' not described in 'VMMOUSE_CMD'
drivers/input/mouse/vmmouse.c:99: warning: Function parameter or member 'out1' not described in 'VMMOUSE_CMD'
drivers/input/mouse/vmmouse.c:99: warning: Function parameter or member 'out2' not described in 'VMMOUSE_CMD'
drivers/input/mouse/vmmouse.c:99: warning: Function parameter or member 'out3' not described in 'VMMOUSE_CMD'
drivers/input/mouse/vmmouse.c:99: warning: Function parameter or member 'out4' not described in 'VMMOUSE_CMD'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-16-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/applespi.c:306: warning: Function parameter or member 'keyboard' not described in 'message'
drivers/input/keyboard/applespi.c:306: warning: Function parameter or member 'touchpad' not described in 'message'
drivers/input/keyboard/applespi.c:306: warning: Function parameter or member 'tp_info' not described in 'message'
drivers/input/keyboard/applespi.c:306: warning: Function parameter or member 'tp_info_command' not described in 'message'
drivers/input/keyboard/applespi.c:306: warning: Function parameter or member 'init_mt_command' not described in 'message'
drivers/input/keyboard/applespi.c:306: warning: Function parameter or member 'capsl_command' not described in 'message'
drivers/input/keyboard/applespi.c:306: warning: Function parameter or member 'bl_command' not described in 'message'
drivers/input/keyboard/applespi.c:306: warning: Function parameter or member 'data' not described in 'message'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-15-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/goodix.c:1168: warning: Function parameter or member 'ctx' not described in 'goodix_config_cb'
drivers/input/touchscreen/goodix.c:1168: warning: Excess function parameter 'ts' description in 'goodix_config_cb'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-14-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/mouse/synaptics.c:1781: warning: Function parameter or member 'psmouse' not described in 'synaptics_setup_intertouch'
drivers/input/mouse/synaptics.c:1781: warning: Function parameter or member 'info' not described in 'synaptics_setup_intertouch'
drivers/input/mouse/synaptics.c:1781: warning: Function parameter or member 'leave_breadcrumbs' not described in 'synaptics_setup_intertouch'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-13-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/wm97xx-core.c:204: warning: Function parameter or member 'status' not described in 'wm97xx_set_gpio'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201112110204.2083435-12-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/surface3_spi.c: In function ‘surface3_spi_process_touch’:
drivers/input/touchscreen/surface3_spi.c:97:6: warning: variable ‘timestamp’ set but not used [-Wunused-but-set-variable]
drivers/input/touchscreen/surface3_spi.c:225: warning: Function parameter or member 'data' not described in 'surface3_spi_get_gpio_config'
drivers/input/touchscreen/surface3_spi.c:225: warning: Excess function parameter 'ts' description in 'surface3_spi_get_gpio_config'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-11-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/misc/wm831x-on.c:30: warning: cannot understand function prototype: 'struct wm831x_on '
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20201112110204.2083435-10-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/goodix.c:569: warning: Function parameter or member 'len' not described in 'goodix_check_cfg'
drivers/input/touchscreen/goodix.c:587: warning: Function parameter or member 'len' not described in 'goodix_send_cfg'
drivers/input/touchscreen/goodix.c:1165: warning: Function parameter or member 'cfg' not described in 'goodix_config_cb'
drivers/input/touchscreen/goodix.c:1165: warning: Function parameter or member 'ctx' not described in 'goodix_config_cb'
drivers/input/touchscreen/goodix.c:1165: warning: Excess function parameter 'ts' description in 'goodix_config_cb'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-5-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/joystick/xpad.c:1361: warning: Function parameter or member 'xpad' not described in 'xpad_send_led_command'
drivers/input/joystick/xpad.c:1361: warning: Function parameter or member 'command' not described in 'xpad_send_led_command'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-2-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This improves compile coverage of the code; unused code will be dropped by
the linker.
Acked-by: Alexandru Ardelean <Alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201119072418.GA114677@dtor-ws
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The driver clears the general configuration register during the remove()
hook. This should also be done in case the driver exits on error.
This change move the clear of that register to the
devm_add_action_or_reset() hook.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201112074308.71351-6-alexandru.ardelean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change makes use of the devm_gpiochip_add_data() function. With this
the gpiochip_remove() function can be removed, and the
adp5589_gpio_remove() function as well.
The kpad->export_gpio variable is also redundant now, and has been removed.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201112074308.71351-5-alexandru.ardelean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is currently just dead code. It's from around a time when
platform-data was used, and a board could hook it's own special callback
for setup/teardown, and a private object (via 'context').
This change removes it, as there are no more users in mainline for this.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201112074308.71351-4-alexandru.ardelean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This change makes use of the devm_input_allocate_device() function, which
gets rid of the input_free_device() and input_unregister_device() calls.
When a device is allocated via input_allocate_device(), the
input_register_device() call will also be device-managed, so there is no
longer need to manually call unregister.
Also, the irq is allocated with the devm_request_threaded_irq(), so with
these two changes, the adp5589_keypad_remove() function is no longer
needed.
This cleans up the error & exit paths.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201112074308.71351-3-alexandru.ardelean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This removes the need to manually free the kpad object and cleans up some
exit/error paths. The error path cleanup should reduce the risk of any
memory leaks with this object.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Link: https://lore.kernel.org/r/20201112074308.71351-2-alexandru.ardelean@analog.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds the code for the Atmel touchscreens such as mXT224 to obtain
power regulators for the supply voltages AVDD and VDD. On mobile phones
such as Samsung GT-I8190 (Golden) this is needed to explicitly bring power
online.
We just enable the regulators at probe() and disable them at remove()
or in the error path for now.
As regulators are naturally stubbed if not available, this should have no
impact on existing systems.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-3-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+DdgYeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGB1sH/0B4REolPPxiQsPL
P45+a2POUU0SQK8NjkcYskQmJ6DnPKkJSXeUU8rzuI2rty5bWEzEBxdUSh064ZaM
DGxkWrdhYNaLJuceNLlanBk3vrM3KwGkaJFSKLgsEXkmH86gl33ptA8nlQVbfc+4
FK4hRZs2J6Y5YRsuzPO8nzzHWs1CThZEcwNPOeIZrAnv+/13zyP/piZ+R/2gKYwy
RVrVrzSTkTGJXotn6J17Sa02+CGv5UqdxOZFv7jimYJOmFT7KnGngNrJbh8aYWk7
vPTRUvGozh6NyYxtRI9LKGZy1yQ05Cl7N927CnFYzD235/eT7zaRDZe1e1JaIE8Z
r2yxGCM=
=ZIYP
-----END PGP SIGNATURE-----
Merge tag 'v5.9' into next
Sync up with mainline to bring in the latest DTS files.
The same clause as its use.
Fixes the following W=1 kernel build warning(s):
include/linux/input/elan-i2c-ids.h:26:36: warning: ‘elan_acpi_id’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112104420.GG1997862@dell
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This is essentially a revert of:
3ac8bf077d ("[PATCH] ads7846: sparc32 warning fix")
By now enable_irq() and disable_irq() are properly defined in
linux/interrupt.h and we do not need to pull in architecture-specific
bits.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
req->sample[1] is not naturally aligned at word boundary, and therefore we
should use get_unaligned_be16() when accessing it.
Fixes: 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845 controller support")
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In some rare cases the 32 bit Rt value will overflow if z2 and x is max,
z1 is minimal value and x_plate_ohms is relatively high (for example 800
ohm). This would happen on some screen age with low pressure.
There are two possible fixes:
- make Rt 64bit
- reorder calculation to avoid overflow
The second variant seems to be preferable, since 64 bit calculation on
32 bit system is a bit more expensive.
Fixes: ffa458c1bd ("spi: ads7846 driver")
Co-developed-by: David Jander <david@protonic.nl>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201113112240.1360-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Starting with 3eac5c7e44 ("Input: ads7846 - extend the driver for ads7845
controller support"), the ads7845 was partially converted to full duplex
mode.
Since it is not touchscreen controller specific, it is better to extend
this conversion to cover entire driver. This will reduce CPU load and make
driver more readable.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201110085041.16303-2-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If touchscreen is released while busy reading HWMON device, the release
can be missed. The IRQ thread is not started because no touch is active
and BTN_TOUCH release event is never sent.
Fixes: f5a28a7d48 ("Input: ads7846 - avoid pen up/down when reading hwmon")
Co-developed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20201027105416.18773-1-o.rempel@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix for use-after-free in the Sun keyboard driver, a fix to firmware
updates on newer ICs in the Elan touchpad diver, and a couple misc
driver fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - fix firmware update on newer ICs
Input: resistive-adc-touch - fix kconfig dependency on IIO_BUFFER
Input: sunkbd - avoid use-after-free in teardown paths
Input: i8042 - allow insmod to succeed on devices without an i8042 controller
Input: adxl34x - clean up a data type in adxl34x_probe()
Fixes the following W=1 kernel build warning(s):
drivers/input/touchscreen/imx6ul_tsc.c: In function ‘adc_irq_fn’:
drivers/input/touchscreen/imx6ul_tsc.c:307:6: warning: variable ‘value’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Link: https://lore.kernel.org/r/20201112110204.2083435-6-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
drivers/input/keyboard/samsung-keypad.c: In function ‘samsung_keypad_irq’:
drivers/input/keyboard/samsung-keypad.c:149:15: warning: variable ‘val’ set but not used [-Wunused-but-set-variable]
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112110204.2083435-3-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do not overwrite spi->mode flags set by spi framework, otherwise the
chip select polarity will get lost.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Link: https://lore.kernel.org/r/20201027095724.18654-3-o.rempel@pengutronix.de
Signed-off-by: Mark Brown <broonie@kernel.org>
Hard-coding resolution for st1633 device was wrong. Some of LCDs like
YTS700TLBC-02-100C has assembled Sitronix st1633 touchcontroller too. But
the resolution is not 320x480 as was hard-coded.
Add new function which reads correct resolution directly from register.
Signed-off-by: Andrej Valek <andrej.valek@siemens.com>
Link: https://lore.kernel.org/r/20201103073949.12198-1-andrej.valek@siemens.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When TOUCHSCREEN_ADC is enabled and IIO_BUFFER is disabled, it results
in the following Kbuild warning:
WARNING: unmet direct dependencies detected for IIO_BUFFER_CB
Depends on [n]: IIO [=y] && IIO_BUFFER [=n]
Selected by [y]:
- TOUCHSCREEN_ADC [=y] && !UML && INPUT [=y] && INPUT_TOUCHSCREEN [=y] && IIO [=y]
The reason is that TOUCHSCREEN_ADC selects IIO_BUFFER_CB without depending
on or selecting IIO_BUFFER while IIO_BUFFER_CB depends on IIO_BUFFER. This
can also fail building the kernel.
Honor the kconfig dependency to remove unmet direct dependency warnings
and avoid any potential build failures.
Fixes: aa132ffb6b ("input: touchscreen: resistive-adc-touch: add generic resistive ADC touchscreen")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201102221504.541279-1-fazilyildiran@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the kerneldoc warnings from building the driver with W=1.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-2-lee.jones@linaro.org
[dtor: folded together several Lee's patches; added more descriptions]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fixes the following W=1 kernel build warning(s):
In file included from drivers/input/touchscreen/cyttsp_i2c_common.c:24:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/input/touchscreen/cyttsp4_i2c.c:17:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char * const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/input/touchscreen/cyttsp4_spi.c:17:
drivers/input/touchscreen/cyttsp4_core.h:236:27: warning: ‘cyttsp4_tch_abs_string’ defined but not used [-Wunused-const-variable=]
236 | static const char * const cyttsp4_tch_abs_string[] = {
| ^~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104162427.2984742-16-lee.jones@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
