Trying to enable the local APIC timer on early K8 revisions
uncovers a number of other issues with it, in conjunction with
the C1E enter path on AMD. Fixing those causes much more churn
and troubles than the benefit of using that timer brings so
don't enable it on K8 at all, falling back to the original
functionality the kernel had wrt to that.
Reported-and-bisected-by: Nick Bowler <nbowler@elliptictech.com>
Cc: Boris Ostrovsky <Boris.Ostrovsky@amd.com>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Cc: Hans Rosenfeld <hans.rosenfeld@amd.com>
Cc: Nick Bowler <nbowler@elliptictech.com>
Cc: Joerg-Volker-Peetz <jvpeetz@web.de>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Link: http://lkml.kernel.org/r/1305636919-31165-3-git-send-email-bp@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit e20a2d205c, as it crashes
certain boxes with specific AMD CPU models.
Moving the lower endpoint of the Erratum 400 check to accomodate
earlier K8 revisions (A-E) opens a can of worms which is simply
not worth to fix properly by tweaking the errata checking
framework:
* missing IntPenging MSR on revisions < CG cause #GP:
http://marc.info/?l=linux-kernel&m=130541471818831
* makes earlier revisions use the LAPIC timer instead of the C1E
idle routine which switches to HPET, thus not waking up in
deeper C-states:
http://lkml.org/lkml/2011/4/24/20
Therefore, leave the original boundary starting with K8-revF.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch fixes a bug reported by a customer, who found
that many unreasonable error interrupts reported on all
non-boot CPUs (APs) during the system boot stage.
According to Chapter 10 of Intel Software Developer Manual
Volume 3A, Local APIC may signal an illegal vector error when
an LVT entry is set as an illegal vector value (0~15) under
FIXED delivery mode (bits 8-11 is 0), regardless of whether
the mask bit is set or an interrupt actually happen. These
errors are seen as error interrupts.
The initial value of thermal LVT entries on all APs always reads
0x10000 because APs are woken up by BSP issuing INIT-SIPI-SIPI
sequence to them and LVT registers are reset to 0s except for
the mask bits which are set to 1s when APs receive INIT IPI.
When the BIOS takes over the thermal throttling interrupt,
the LVT thermal deliver mode should be SMI and it is required
from the kernel to keep AP's LVT thermal monitoring register
programmed as such as well.
This issue happens when BIOS does not take over thermal throttling
interrupt, AP's LVT thermal monitor register will be restored to
0x10000 which means vector 0 and fixed deliver mode, so all APs will
signal illegal vector error interrupts.
This patch check if interrupt delivery mode is not fixed mode before
restoring AP's LVT thermal monitor register.
Signed-off-by: Youquan Song <youquan.song@intel.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Yong Wang <yong.y.wang@intel.com>
Cc: hpa@linux.intel.com
Cc: joe@perches.com
Cc: jbaron@redhat.com
Cc: trenn@suse.de
Cc: kent.liu@intel.com
Cc: chaohong.guo@intel.com
Cc: <stable@kernel.org> # As far back as possible
Link: http://lkml.kernel.org/r/1303402963-17738-1-git-send-email-youquan.song@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
b may be added to a list, but is not removed before being freed
in the case of an error. This is done in the corresponding
deallocation function, so the code here has been changed to
follow that.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E1,E2;
identifier l;
@@
*list_add(&E->l,E1);
... when != E1
when != list_del(&E->l)
when != list_del_init(&E->l)
when != E = E2
*kfree(E);// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Borislav Petkov <borislav.petkov@amd.com>
Cc: Robert Richter <robert.richter@amd.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1305294731-12127-1-git-send-email-julia@diku.dk
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The Intel Nehalem offcore bits implemented in:
e994d7d23a: perf: Fix LLC-* events on Intel Nehalem/Westmere
... are wrong: they implemented _ACCESS as _HIT and counted OTHER_CORE_HIT* as
MISS even though its clearly documented as an L3 hit ...
Fix them and the Westmere definitions as well.
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Lin Ming <ming.m.lin@intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/r/1299119690-13991-3-git-send-email-ming.m.lin@intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With dynamic debug having gained the capability to report debug messages
also during the boot process, it offers a far superior interface for
debug messages than the custom cpufreq infrastructure. As a first step,
remove the old cpufreq_debug_printk() function and replace it with a call
to the generic pr_debug() function.
How can dynamic debug be used on cpufreq? You need a kernel which has
CONFIG_DYNAMIC_DEBUG enabled.
To enabled debugging during runtime, mount debugfs and
$ echo -n 'module cpufreq +p' > /sys/kernel/debug/dynamic_debug/control
for debugging the complete "cpufreq" module. To achieve the same goal during
boot, append
ddebug_query="module cpufreq +p"
as a boot parameter to the kernel of your choice.
For more detailled instructions, please see
Documentation/dynamic-debug-howto.txt
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
UUID needs to be written out the way it is described in
Sec 18.5.124 of ACPI 4.0a Specification.
Platform firmware's use of this UUID/_OSC is optional, which is
why we didn't notice this bug earlier.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: stable@kernel.org
Older AMD K8 processors (Revisions A-E) are affected by erratum
400 (APIC timer interrupts don't occur in C states greater than
C1). This, for example, means that X86_FEATURE_ARAT flag should
not be set for these parts.
This addresses regression introduced by commit
b87cf80af3 ("x86, AMD: Set ARAT
feature on AMD processors") where the system may become
unresponsive until external interrupt (such as keyboard input)
occurs. This results, for example, in time not being reported
correctly, lack of progress on the system and other lockups.
Reported-by: Joerg-Volker Peetz <jvpeetz@web.de>
Tested-by: Joerg-Volker Peetz <jvpeetz@web.de>
Acked-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Boris Ostrovsky <Boris.Ostrovsky@amd.com>
Cc: stable@kernel.org
Link: http://lkml.kernel.org/r/1304113663-6586-1-git-send-email-ostr@amd64.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It was noticed that P4 machines were generating double NMIs for
each perf event. These extra NMIs lead to 'Dazed and confused'
messages on the screen.
I tracked this down to a P4 quirk that said the overflow bit had
to be cleared before re-enabling the apic LVT mask. My first
attempt was to move the un-masking inside the perf nmi handler
from before the chipset NMI handler to after.
This broke Nehalem boxes that seem to like the unmasking before
the counters themselves are re-enabled.
In order to keep this change simple for 2.6.39, I decided to
just simply move the apic LVT un-masking to the beginning of all
the chipset NMI handlers, with the exception of Pentium4's to
fix the double NMI issue.
Later on we can move the un-masking to later in the handlers to
save a number of 'extra' NMIs on those particular chipsets.
I tested this change on a P4 machine, an AMD machine, a Nehalem
box, and a core2quad box. 'perf top' worked correctly along
with various other small 'perf record' runs. Anything high
stress breaks all the machines but that is a different problem.
Thanks to various people for testing different versions of this
patch.
Reported-and-tested-by: Shaun Ruffell <sruffell@digium.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303900353-10242-1-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
CC: Cyrill Gorcunov <gorcunov@gmail.com>
On Nehalem CPUs the retired branch-misses event can be completely bogus,
when there are no branch-misses occuring. When there are a lot of branch
misses then the count is pretty accurate. Still, this leaves us with an
event that over-counts a lot.
Detect this erratum and work it around by using BR_MISP_EXEC.ANY events.
These will also count speculated branches but still it's a lot more
precise in practice than the architectural event.
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-yyfg0bxo9jsqxd6a0ovfny27@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently the x86 backend incorrectly assumes that any BRANCH_INSN
with sample_period==1 is a BTS request. This is not true when we do
frequency driven profiling such as 'perf record -e branches'.
Solves this error:
$ perf record -e branches ./array
Error: sys_perf_event_open() syscall returned with 95 (Operation not supported).
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Reported-by: Ingo Molnar <mingo@elte.hu>
Cc: "Metzger, Markus T" <markus.t.metzger@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Link: http://lkml.kernel.org/n/tip-rd2y4ct71hjawzz6fpvsy9hg@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It's not enough to simply disable event on overflow the
cpuc->active_mask should be cleared as well otherwise counter
may stall in "active" even in real being already disabled (which
potentially may lead to the situation that user may not use this
counter further).
Don pointed out that:
" I also noticed this patch fixed some unknown NMIs
on a P4 when I stressed the box".
Tested-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Don Zickus <dzickus@redhat.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Link: http://lkml.kernel.org/r/1303398203-2918-3-git-send-email-dzickus@redhat.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Andi Kleen pointed out that the Intel offcore support patches were merged
without user-space tool support to the functionality:
|
| The offcore_msr perf kernel code was merged into 2.6.39-rc*, but the
| user space bits were not. This made it impossible to set the extra mask
| and actually do the OFFCORE profiling
|
Andi submitted a preliminary patch for user-space support, as an
extension to perf's raw event syntax:
|
| Some raw events -- like the Intel OFFCORE events -- support additional
| parameters. These can be appended after a ':'.
|
| For example on a multi socket Intel Nehalem:
|
| perf stat -e r1b7:20ff -a sleep 1
|
| Profile the OFFCORE_RESPONSE.ANY_REQUEST with event mask REMOTE_DRAM_0
| that measures any access to DRAM on another socket.
|
But this kind of usability is absolutely unacceptable - users should not
be expected to type in magic, CPU and model specific incantations to get
access to useful hardware functionality.
The proper solution is to expose useful offcore functionality via
generalized events - that way users do not have to care which specific
CPU model they are using, they can use the conceptual event and not some
model specific quirky hexa number.
We already have such generalization in place for CPU cache events,
and it's all very extensible.
"Offcore" events measure general DRAM access patters along various
parameters. They are particularly useful in NUMA systems.
We want to support them via generalized DRAM events: either as the
fourth level of cache (after the last-level cache), or as a separate
generalization category.
That way user-space support would be very obvious, memory access
profiling could be done via self-explanatory commands like:
perf record -e dram ./myapp
perf record -e dram-remote ./myapp
... to measure DRAM accesses or more expensive cross-node NUMA DRAM
accesses.
These generalized events would work on all CPUs and architectures that
have comparable PMU features.
( Note, these are just examples: actual implementation could have more
sophistication and more parameter - as long as they center around
similarly simple usecases. )
Now we do not want to revert *all* of the current offcore bits, as they
are still somewhat useful for generic last-level-cache events, implemented
in this commit:
e994d7d23a: perf: Fix LLC-* events on Intel Nehalem/Westmere
But we definitely do not yet want to expose the unstructured raw events
to user-space, until better generalization and usability is implemented
for these hardware event features.
( Note: after generalization has been implemented raw offcore events can be
supported as well: there can always be an odd event that is marginally
useful but not useful enough to generalize. DRAM profiling is definitely
*not* such a category so generalization must be done first. )
Furthermore, PERF_TYPE_RAW access to these registers was not intended
to go upstream without proper support - it was a side-effect of the above
e994d7d23a commit, not mentioned in the changelog.
As v2.6.39 is nearing release we go for the simplest approach: disable
the PERF_TYPE_RAW offcore hack for now, before it escapes into a released
kernel and becomes an ABI.
Once proper structure is implemented for these hardware events and users
are offered usable solutions we can revisit this issue.
Reported-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1302658203-4239-1-git-send-email-andi@firstfloor.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Fix AMD family 15h FPU event constraints
perf, x86: Fix pre-defined cache-misses event for AMD family 15h cpus
perf evsel: Fix use of inherit
perf hists browser: Fix seg fault when annotate null symbol
Depending on the unit mask settings some FPU events may be scheduled
only on cpu counter #3. This patch fixes this.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@googlemail.com>
Link: http://lkml.kernel.org/r/1302913676-14352-3-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With AMD cpu family 15h a unit mask was introduced for the Data Cache
Miss event (0x041/L1-dcache-load-misses). We need to enable bit 0
(first data cache miss or streaming store to a 64 B cache line) of
this mask to proper count data cache misses.
Now we set this bit for all families and models. In case a PMU does
not implement a unit mask for event 0x041 the bit is ignored.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1302913676-14352-2-git-send-email-robert.richter@amd.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch disables GartTlbWlk errors on AMD Fam10h CPUs if
the BIOS forgets to do is (or is just too old). Letting
these errors enabled can cause a sync-flood on the CPU
causing a reboot.
The AMD BKDG recommends disabling GART TLB Wlk Error completely.
This patch is the fix for
https://bugzilla.kernel.org/show_bug.cgi?id=33012
on my machine.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Link: http://lkml.kernel.org/r/20110415131152.GJ18463@8bytes.org
Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, UV: Fix kdump reboot
x86, amd-nb: Rename CPU PCI id define for F4
sound: Add delay.h to sound/soc/codecs/sn95031.c
x86, mtrr, pat: Fix one cpu getting out of sync during resume
x86, microcode: Unregister syscore_ops after microcode unloaded
x86: Stop including <linux/delay.h> in two asm header files
The MCE subsystem needs to sample an RCU-protected index outside of
any protection for that index. If this was a pointer, we would use
rcu_access_pointer(), but there is no corresponding rcu_access_index().
This commit therefore creates an rcu_access_index() and applies it
to MCE.
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Zdenek Kabelac <zkabelac@redhat.com>
On laptops with core i5/i7, there were reports that after resume
graphics workloads were performing poorly on a specific AP, while
the other cpu's were ok. This was observed on a 32bit kernel
specifically.
Debug showed that the PAT init was not happening on that AP
during resume and hence it contributing to the poor workload
performance on that cpu.
On this system, resume flow looked like this:
1. BP starts the resume sequence and we reinit BP's MTRR's/PAT
early on using mtrr_bp_restore()
2. Resume sequence brings all AP's online
3. Resume sequence now kicks off the MTRR reinit on all the AP's.
4. For some reason, between point 2 and 3, we moved from BP
to one of the AP's. My guess is that printk() during resume
sequence is contributing to this. We don't see similar
behavior with the 64bit kernel but there is no guarantee that
at this point the remaining resume sequence (after AP's bringup)
has to happen on BP.
5. set_mtrr() was assuming that we are still on BP and skipped the
MTRR/PAT init on that cpu (because of 1 above)
6. But we were on an AP and this led to not reprogramming PAT
on this cpu leading to bad performance.
Fix this by doing unconditional mtrr_if->set_all() in set_mtrr()
during MTRR/PAT init. This might be unnecessary if we are still
running on BP. But it is of no harm and will guarantee that after
resume, all the cpu's will be in sync with respect to the
MTRR/PAT registers.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1301438292-28370-1-git-send-email-eric@anholt.net>
Signed-off-by: Eric Anholt <eric@anholt.net>
Tested-by: Keith Packard <keithp@keithp.com>
Cc: stable@kernel.org [v2.6.32+]
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
* 'syscore' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/suspend-2.6:
Introduce ARCH_NO_SYSDEV_OPS config option (v2)
cpufreq: Use syscore_ops for boot CPU suspend/resume (v2)
KVM: Use syscore_ops instead of sysdev class and sysdev
PCI / Intel IOMMU: Use syscore_ops instead of sysdev class and sysdev
timekeeping: Use syscore_ops instead of sysdev class and sysdev
x86: Use syscore_ops instead of sysdev classes and sysdevs
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, x86: Complain louder about BIOSen corrupting CPU/PMU state and continue
perf, x86: P4 PMU - Read proper MSR register to catch unflagged overflows
perf symbols: Look at .dynsym again if .symtab not found
perf build-id: Add quirk to deal with perf.data file format breakage
perf session: Pass evsel in event_ops->sample()
perf: Better fit max unprivileged mlock pages for tools needs
perf_events: Fix stale ->cgrp pointer in update_cgrp_time_from_cpuctx()
perf top: Fix uninitialized 'counter' variable
tracing: Fix set_ftrace_filter probe function display
perf, x86: Fix Intel fixed counters base initialization
Eric Dumazet reported that hardware PMU events do not work on his
system, due to the BIOS corrupting PMU state:
Performance Events: PEBS fmt0+, Core2 events, Broken BIOS detected, using software events only.
[Firmware Bug]: the BIOS has corrupted hw-PMU resources (MSR 186 is 43003c)
Linus suggested that we continue in the face of such BIOS-induced CPU
state corruption:
http://lkml.org/lkml/2011/3/24/608
Such BIOSes will have to be fixed - Linux developers rely on a working and
fully capable PMU and the BIOS interfering with the CPU's PMU state is simply
not acceptable.
So this patch changes perf to continue when it detects such BIOS
interaction, some hardware events may be unreliable due to the BIOS
writing and re-writing them - there's not much the kernel can do
about that but to detect the corruption and report it.
Reported-and-tested-by: Eric Dumazet <eric.dumazet@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Steven Rostedt <rostedt@goodmis.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The read of a proper MSR register was missed and instead of
counter the configration register was tested (it has
ARCH_P4_UNFLAGGED_BIT always cleared) leading to unknown NMI
hitting the system. As result the user may obtain "Dazed and
confused, but trying to continue" message. Fix it by reading a
proper MSR register.
When an NMI happens on a P4, the perf nmi handler checks the
configuration register to see if the overflow bit is set or not
before taking appropriate action. Unfortunately, various P4
machines had a broken overflow bit, so a backup mechanism was
implemented. This mechanism checked to see if the counter
rolled over or not.
A previous commit that implemented this backup mechanism was
broken. Instead of reading the counter register, it used the
configuration register to determine if the counter rolled over
or not. Reading that bit would give incorrect results.
This would lead to 'Dazed and confused' messages for the end
user when using the perf tool (or if the nmi watchdog is
running).
The fix is to read the counter register before determining if
the counter rolled over or not.
Signed-off-by: Don Zickus <dzickus@redhat.com>
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: Lin Ming <ming.m.lin@intel.com>
LKML-Reference: <4D8BAB49.3080701@openvz.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some subsystems in the x86 tree need to carry out suspend/resume and
shutdown operations with one CPU on-line and interrupts disabled and
they define sysdev classes and sysdevs or sysdev drivers for this
purpose. This leads to unnecessarily complicated code and excessive
memory usage, so switch them to using struct syscore_ops objects for
this purpose instead.
Generally, there are three categories of subsystems that use
sysdevs for implementing PM operations: (1) subsystems whose
suspend/resume callbacks ignore their arguments entirely (the
majority), (2) subsystems whose suspend/resume callbacks use their
struct sys_device argument, but don't really need to do that,
because they can be implemented differently in an arguably simpler
way (io_apic.c), and (3) subsystems whose suspend/resume callbacks
use their struct sys_device argument, but the value of that argument
is always the same and could be ignored (microcode_core.c). In all
of these cases the subsystems in question may be readily converted to
using struct syscore_ops objects for power management and shutdown.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
APEI ERST firmware interface and implementation has no multiple users
in mind. For example, if there is four records in storage with ID: 1,
2, 3 and 4, if two ERST readers enumerate the records via
GET_NEXT_RECORD_ID as follow,
reader 1 reader 2
1
2
3
4
-1
-1
where -1 signals there is no more record ID.
Reader 1 has no chance to check record 2 and 4, while reader 2 has no
chance to check record 1 and 3. And any other GET_NEXT_RECORD_ID will
return -1, that is, other readers will has no chance to check any
record even they are not cleared by anyone.
This makes raw GET_NEXT_RECORD_ID not suitable for used by multiple
users.
To solve the issue, an in-memory ERST record ID cache is designed and
implemented. When enumerating record ID, the ID returned by
GET_NEXT_RECORD_ID is added into cache in addition to be returned to
caller. So other readers can check the cache to get all record ID
available.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The following patch solves the problems introduced by Robert's
commit 41bf498 and reported by Arun Sharma. This commit gets rid
of the base + index notation for reading and writing PMU msrs.
The problem is that for fixed counters, the new calculation for
the base did not take into account the fixed counter indexes,
thus all fixed counters were read/written from fixed counter 0.
Although all fixed counters share the same config MSR, they each
have their own counter register.
Without:
$ task -e unhalted_core_cycles -e instructions_retired -e baclears noploop 1 noploop for 1 seconds
242202299 unhalted_core_cycles (0.00% scaling, ena=1000790892, run=1000790892)
2389685946 instructions_retired (0.00% scaling, ena=1000790892, run=1000790892)
49473 baclears (0.00% scaling, ena=1000790892, run=1000790892)
With:
$ task -e unhalted_core_cycles -e instructions_retired -e baclears noploop 1 noploop for 1 seconds
2392703238 unhalted_core_cycles (0.00% scaling, ena=1000840809, run=1000840809)
2389793744 instructions_retired (0.00% scaling, ena=1000840809, run=1000840809)
47863 baclears (0.00% scaling, ena=1000840809, run=1000840809)
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Cc: ming.m.lin@intel.com
Cc: robert.richter@amd.com
Cc: asharma@fb.com
Cc: perfmon2-devel@lists.sf.net
LKML-Reference: <20110319172005.GB4978@quad>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Flush TLB if PGD entry is changed in i386 PAE mode
x86, dumpstack: Correct stack dump info when frame pointer is available
x86: Clean up csum-copy_64.S a bit
x86: Fix common misspellings
x86: Fix misspelling and align params
x86: Use PentiumPro-optimized partial_csum() on VIA C7
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
trace, filters: Initialize the match variable in process_ops() properly
trace, documentation: Fix branch profiling location in debugfs
oprofile, s390: Cleanups
oprofile, s390: Remove hwsampler_files.c and merge it into init.c
perf: Fix tear-down of inherited group events
perf: Reorder & optimize perf_event_context to remove alignment padding on 64 bit builds
perf: Handle stopped state with tracepoints
perf: Fix the software events state check
perf, powerpc: Handle events that raise an exception without overflowing
perf, x86: Use INTEL_*_CONSTRAINT() for all PEBS event constraints
perf, x86: Clean up SandyBridge PEBS events
perf lock: Fix sorting by wait_min
perf tools: Version incorrect with some versions of grep
perf evlist: New command to list the names of events present in a perf.data file
perf script: Add support for H/W and S/W events
perf script: Add support for dumping symbols
perf script: Support custom field selection for output
perf script: Move printing of 'common' data from print_event and rename
perf tracing: Remove print_graph_cpu and print_graph_proc from trace-event-parse
perf script: Change process_event prototype
...
Current stack dump code scans entire stack and check each entry
contains a pointer to kernel code. If CONFIG_FRAME_POINTER=y it
could mark whether the pointer is valid or not based on value of
the frame pointer. Invalid entries could be preceded by '?' sign.
However this was not going to happen because scan start point
was always higher than the frame pointer so that they could not
meet.
Commit 9c0729dc80 ("x86: Eliminate bp argument from the stack
tracing routines") delayed bp acquisition point, so the bp was
read in lower frame, thus all of the entries were marked
invalid.
This patch fixes this by reverting above commit while retaining
stack_frame() helper as suggested by Frederic Weisbecker.
End result looks like below:
before:
[ 3.508329] Call Trace:
[ 3.508551] [<ffffffff814f35c9>] ? panic+0x91/0x199
[ 3.508662] [<ffffffff814f3739>] ? printk+0x68/0x6a
[ 3.508770] [<ffffffff81a981b2>] ? mount_block_root+0x257/0x26e
[ 3.508876] [<ffffffff81a9821f>] ? mount_root+0x56/0x5a
[ 3.508975] [<ffffffff81a98393>] ? prepare_namespace+0x170/0x1a9
[ 3.509216] [<ffffffff81a9772b>] ? kernel_init+0x1d2/0x1e2
[ 3.509335] [<ffffffff81003894>] ? kernel_thread_helper+0x4/0x10
[ 3.509442] [<ffffffff814f6880>] ? restore_args+0x0/0x30
[ 3.509542] [<ffffffff81a97559>] ? kernel_init+0x0/0x1e2
[ 3.509641] [<ffffffff81003890>] ? kernel_thread_helper+0x0/0x10
after:
[ 3.522991] Call Trace:
[ 3.523351] [<ffffffff814f35b9>] panic+0x91/0x199
[ 3.523468] [<ffffffff814f3729>] ? printk+0x68/0x6a
[ 3.523576] [<ffffffff81a981b2>] mount_block_root+0x257/0x26e
[ 3.523681] [<ffffffff81a9821f>] mount_root+0x56/0x5a
[ 3.523780] [<ffffffff81a98393>] prepare_namespace+0x170/0x1a9
[ 3.523885] [<ffffffff81a9772b>] kernel_init+0x1d2/0x1e2
[ 3.523987] [<ffffffff81003894>] kernel_thread_helper+0x4/0x10
[ 3.524228] [<ffffffff814f6880>] ? restore_args+0x0/0x30
[ 3.524345] [<ffffffff81a97559>] ? kernel_init+0x0/0x1e2
[ 3.524445] [<ffffffff81003890>] ? kernel_thread_helper+0x0/0x10
-v5:
* fix build breakage with oprofile
-v4:
* use 0 instead of regs->bp
* separate out printk changes
-v3:
* apply comment from Frederic
* add a couple of printk fixes
Signed-off-by: Namhyung Kim <namhyung@gmail.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Soren Sandmann <ssp@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Robert Richter <robert.richter@amd.com>
LKML-Reference: <1300416006-3163-1-git-send-email-namhyung@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
They were generated by 'codespell' and then manually reviewed.
Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: trivial@kernel.org
LKML-Reference: <1300389856-1099-3-git-send-email-lucas.demarchi@profusion.mobi>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove a couple of assigment statements that appear twice.
Signed-off-by: Naga Chumbalkar <nagananda.chumbalkar@hp.com>
Signed-off-by: Dave Jones <davej@redhat.com>
PEBS_EVENT_CONSTRAINT() is just a duplicate of INTEL_UEVENT_CONSTRAINT().
Remove it and use INTEL_UEVENT_CONSTRAINT() instead.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1299684089-22835-3-git-send-email-ming.m.lin@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use INTEL_EVENT_CONSTRAINT() for the events where all umasks support PEBS.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1299684089-22835-2-git-send-email-ming.m.lin@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Support for Always Running APIC timer (ARAT) was introduced in
commit db954b5898. This feature
allows us to avoid switching timers from LAPIC to something else
(e.g. HPET) and go into timer broadcasts when entering deep
C-states.
AMD processors don't provide a CPUID bit for that feature but
they also keep APIC timers running in deep C-states (except for
cases when the processor is affected by erratum 400). Therefore
we should set ARAT feature bit on AMD CPUs.
Tested-by: Borislav Petkov <borislav.petkov@amd.com>
Acked-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@amd.com>
LKML-Reference: <1300205624-4813-1-git-send-email-ostr@amd64.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (93 commits)
x86, tlb, UV: Do small micro-optimization for native_flush_tlb_others()
x86-64, NUMA: Don't call numa_set_distanc() for all possible node combinations during emulation
x86-64, NUMA: Don't assume phys node 0 is always online in numa_emulation()
x86-64, NUMA: Clean up initmem_init()
x86-64, NUMA: Fix numa_emulation code with node0 without RAM
x86-64, NUMA: Revert NUMA affine page table allocation
x86: Work around old gas bug
x86-64, NUMA: Better explain numa_distance handling
x86-64, NUMA: Fix distance table handling
mm: Move early_node_map[] reverse scan helpers under HAVE_MEMBLOCK
x86-64, NUMA: Fix size of numa_distance array
x86: Rename e820_table_* to pgt_buf_*
bootmem: Move __alloc_memory_core_early() to nobootmem.c
bootmem: Move contig_page_data definition to bootmem.c/nobootmem.c
bootmem: Separate out CONFIG_NO_BOOTMEM code into nobootmem.c
x86-64, NUMA: Seperate out numa_alloc_distance() from numa_set_distance()
x86-64, NUMA: Add proper function comments to global functions
x86-64, NUMA: Move NUMA emulation into numa_emulation.c
x86-64, NUMA: Prepare numa_emulation() for moving NUMA emulation into a separate file
x86-64, NUMA: Do not scan two times for setup_node_bootmem()
...
Fix up conflicts in arch/x86/kernel/smpboot.c
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix and clean up generic_processor_info()
x86: Don't copy per_cpu cpuinfo for BSP two times
x86: Move llc_shared_map out of cpu_info
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, binutils, xen: Fix another wrong size directive
x86: Remove dead config option X86_CPU
x86: Really print supported CPUs if PROCESSOR_SELECT=y
x86: Fix a bogus unwind annotation in lib/semaphore_32.S
um, x86-64: Fix UML build after adding CFI annotations to lib/rwsem_64.S
x86: Remove unused bits from lib/thunk_*.S
x86: Use {push,pop}_cfi in more places
x86-64: Add CFI annotations to lib/rwsem_64.S
x86, asm: Cleanup unnecssary macros in asm-offsets.c
x86, system.h: Drop unused __SAVE/__RESTORE macros
x86: Use bitmap library functions
x86: Partly unify asm-offsets_{32,64}.c
x86: Reduce back the alignment of the per-CPU data section
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (184 commits)
perf probe: Clean up probe_point_lazy_walker() return value
tracing: Fix irqoff selftest expanding max buffer
tracing: Align 4 byte ints together in struct tracer
tracing: Export trace_set_clr_event()
tracing: Explain about unstable clock on resume with ring buffer warning
ftrace/graph: Trace function entry before updating index
ftrace: Add .ref.text as one of the safe areas to trace
tracing: Adjust conditional expression latency formatting.
tracing: Fix event alignment: skb:kfree_skb
tracing: Fix event alignment: mce:mce_record
tracing: Fix event alignment: kvm:kvm_hv_hypercall
tracing: Fix event alignment: module:module_request
tracing: Fix event alignment: ftrace:context_switch and ftrace:wakeup
tracing: Remove lock_depth from event entry
perf header: Stop using 'self'
perf session: Use evlist/evsel for managing perf.data attributes
perf top: Don't let events to eat up whole header line
perf top: Fix events overflow in top command
ring-buffer: Remove unused #include <linux/trace_irq.h>
tracing: Add an 'overwrite' trace_option.
...
