Not having a reset control line to the ethernet controller should not be a
hard failure. Instead, add support for deferred probing and just print out
a debug statement.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we're getting IRQs after lots of resources are already
allocated:
* netdev
* clocks
* MDIO bus
Also HW gets initialized by the time when checking IRQs as well.
Now there's a possibility for master interrupt controller to be not
probed yet. This will lead to exit from GMAC probe routine with "-
EPROBE_DEFER" and so deferred probe will hapen later on.
But since we exited the first GMAC probe without release of all
allocated resources there could be conflicts on subsequent probes.
For example this is what happens for me:
--->8---
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
libphy: stmmac: probed
eth0: PHY ID 20005c7a at 1 IRQ POLL (stmmac-0:01) active
platform e0018000.ethernet: Driver stmmaceth requests probe deferral
...
...
...
stmmaceth e0018000.ethernet: no reset control found
stmmac - user ID: 0x10, Synopsys ID: 0x37
Ring mode enabled
DMA HW capability register supported
Normal descriptors
RX Checksum Offload Engine supported (type 2)
TX Checksum insertion supported
Enable RX Mitigation via HW Watchdog Timer
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x4e/0x68()
sysfs: cannot create duplicate filename
'/devices/platform/axs10x_mb/e0018000.ethernet/mdio_bus/stmmac-0'
CPU: 0 PID: 6 Comm: kworker/u2:0 Not tainted 4.0.0-rc1-next-20150303+#8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
sysfs_warn_dup+0x4e/0x68
sysfs_create_dir_ns+0x98/0xa0
kobject_add_internal+0x8c/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be1 ]---
------------[ cut here ]------------
WARNING: CPU: 0 PID: 6 at lib/kobject.c:240
kobject_add_internal+0x218/0x2e8()
kobject_add_internal failed for stmmac-0 with -EEXIST, don't try to
register things with the same name in the same di.
CPU: 0 PID: 6 Comm: kworker/u2:0 Tainted: G W
4.0.0-rc1-next-20150303+ #8
Workqueue: deferwq deferred_probe_work_func
Stack Trace:
arc_unwind_core+0xb8/0x114
warn_slowpath_common+0x5a/0x8c
warn_slowpath_fmt+0x2e/0x38
kobject_add_internal+0x218/0x2e8
kobject_add+0x4a/0x8c
device_add+0xc6/0x448
mdiobus_register+0x6c/0x164
stmmac_mdio_register+0x112/0x264
stmmac_dvr_probe+0x6c0/0x85c
stmmac_pltfr_probe+0x2e4/0x50c
platform_drv_probe+0x26/0x5c
really_probe+0x76/0x1dc
bus_for_each_drv+0x42/0x7c
device_attach+0x64/0x6c
bus_probe_device+0x74/0xa4
deferred_probe_work_func+0x50/0x84
process_one_work+0xf8/0x2cc
worker_thread+0x110/0x478
kthread+0x8a/0x9c
ret_from_fork+0x14/0x18
---[ end trace a2dfaa7d630c8be2 ]---
libphy: mii_bus stmmac-0 failed to register
: Cannot register as MDIO bus
stmmac_pltfr_probe: main driver probe failed
stmmaceth: probe of e0018000.ethernet failed with error -22
--->8---
Essential fix is to check for IRQs availability as early as possible and
then safely go to deferred probe if IRQs are not there yet.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- In tx_hard_error_bump_tc interrupt, tc should be bumped only when current
device instance is in DMA threshold mode. Check per device xstats.threshold
other than global tc.
- Set per device xstats.threshold to SF_DMA_MODE when current device
instance is set to SF mode.
v2-changes:
- fix ident style
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In Intel Quark SoC X1000, both of the Ethernet controllers support
MSI interrupt handling. This patch enables them to use MSI interrupt
servicing in stmmac_pci for Intel Quark X1000.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces run-time board detection through DMI and MAC-PHY
configuration function used by quark_default_data() during initialization. It
fills up the phy_addr for Galileo and Galileo Gen2 boards to indicate that the
Ethernet MAC controller is or is not connected to any PHY.
The implementation takes into consideration for future expansion in Quark
series boards that may have different PHY address that is linked to its MAC
controllers.
This piece of work is derived from Bryan O'Donoghue's initial work for Quark
X1000 enabling.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Intel Quark SoC X1000 provides two 10/100 Mbps Ethernet MAC
controllers which may or may not be connected to PHY on board.
This MAC controller only supports RMII PHY. This patch add Quark
PCI ID as well as Quark default platform data info to this driver.
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case when alloc_netdev fails we return NULL to a caller. But there is no
check for NULL in the probe drivers. This patch changes NULL to an error
pointer. The function description is amended to reflect what we may get
returned.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clear the TX COE bit when force_thresh_dma_mode is set even hardware
dma capability says support.
Tested on BF609.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont' pass SF_DMA_MODE to rxmode in this case.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for Byte Queue Limits to the STMicro MAC driver.
Tested on a Amlogic S802 quad Cortex-A9 board, where the use of BQL
decreases the latency of a high priority ping from ~12ms to ~1ms when
the 100Mbit link is saturated by 20 TCP streams.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, dwmac-rk uses a custom propety "phy_regulator" to get the name of the
right regulator to use to power on or power off the phy. This commit converts the
driver to use phy-supply devicetree property and the corresponding API, it cleans
the code a bit and make it simpler to maintain. This also replaces the property
phy_regulator by the standard property phy-supply in rk3288-evb-rk808.dts.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As these settings can be directly expressed from devicetree for both fixed
regulators and pmic-integrated regulators, it is more standard to set them
from dts and let the regulator framework use the right voltage informations
when it is used in the driver.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Based on Arnds review comments here https://lkml.org/lkml/2014/11/13/161,
we should not be mixing address spaces in the reg property like this driver
currently does. This patch updates the driver, dt docs and also the existing
dt nodes to pass the sysconfig offset in the syscon dt property.
This patch breaks DT compatibility! But this platform is considered WIP,
and is only used by a few developers who are upstreaming support for it.
This change has been done as a single atomic commit to ensure it is
bisectable.
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver is based on stmmac driver.
changes since v2:
- use tab instead of space for macros
- use HIWORD_UPDATE macro for GMAC_CLK_RX_DL_CFG and GMAC_CLK_TX_DL_CFG
- remove drive-strength setting in the driver and set it in the pinctrl settings
- use dev_err instead of pr_err
- remove clock names's macros, just use the real name of the clock
- use devm_clk_get() instead of clk_get()
- remove clk_set_parent(bsp_priv->clk_mac, bsp_priv->clk_mac_pll)
- remove gpio setting for LDO, just use regulator API
- remove phy reset using gpio in the glue layer, it has been handled in the stmmac driver
- remove handling phy interrupt (mii interrupt)
changes since v1:
- use BIT() to set register
- combine two remap_write() operations into one for the same register
- use macros for register value setting
- remove grf fail check in rk_gmac_setup() and save all the check in set_rgmii_speed()
- remove .tx_coe=1 in rk_gmac_data
Signed-off-by: Roger Chen <roger.chen@rock-chips.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both stmmac_open() and stmmac_resume() call stmmac_hw_setup(), and
stmmac_hw_setup() call stmmac_init_ptp() unconditionally. However, only
stmmac_release() calls stmmac_release_ptp(). Since stmmac_suspend()
doesn't call stmmac_release_ptp(), stmmac_resume() also needn't call
stmmac_init_ptp().
This patch also fix a "scheduling while atomic" problem when resume
from suspend/hibernation. Because stmmac_init_ptp() will trigger
scheduling while stmmac_resume() hold a spinlock.
Callgraph of "scheduling while atomic":
stmmac_resume() --> stmmac_hw_setup() --> stmmac_init_ptp() -->
stmmac_ptp_register() --> ptp_clock_register() --> device_create() -->
device_create_groups_vargs() --> device_add() --> devtmpfs_create_node()
--> wait_for_common() --> schedule_timeout() --> __schedule()
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_OF is not set:
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c: In function ‘sti_dwmac_parse_data’:
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:318: warning: ‘rs’ is used uninitialized in this function
of_property_read_string() will return -ENOSYS in this case, and rs will
be an uninitialized pointer.
While the fallback clock selection is already selected correctly in this
case, the string comparisons should be skipped too, else the system will
crash while dereferencing the uninitialized pointer.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/amd/xgbe/xgbe-desc.c
drivers/net/ethernet/renesas/sh_eth.c
Overlapping changes in both conflict cases.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the max coalesce timer setting that can be provided
by ethtool.
The default value (STMMAC_COAL_TX_TIMER) was used in the set_coalesce helper
instead of the max one (STMMAC_MAX_COAL_TX_TICK, so defined but not used).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using global variables we are going to use dynamically allocated
memory. It allows to append a support of more than one ethernet adapter which
might have different settings simultaniously.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Original code only check/alloc plat_dat for the CONFIG_OF case, this
patch check/alloc it earlier and unconditionally to avoid kernel build
warnings:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:275
stmmac_pltfr_probe() warn: variable dereferenced before check 'plat_dat'
V2: Fix coding style.
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3b57de958e brought the support for a different amount of
the filter bins, but didn't update the platform driver that without
CONFIG_OF.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast
and ucast filter entries)
Signed-off-by: Huacai Chen <chenhc@lemote.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When run ./scripts/kernel-doc several warnings are reported
so this patch fix them.
Also it reviews many comments and adds new ones.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds some useful comments inside the common header
file to provide information about the APIs exposed by the driver.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of registering the platform and PCI drivers in one module let's move
necessary bits to where it belongs. During this procedure we convert the module
registration part to use module_*_driver() macros which makes code simplier.
>From now on the driver consists three parts: core library, PCI, and platform
drivers.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings. One is fixed by casting return
value to a return type of the function. The others by creating a specific
stmmac_platform.h which provides the bits related to the platform driver.
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:59:29: warning: incorrect type in return expression (different address spaces)
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:59:29: expected void *
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:59:29: got void [noderef] <asn:2>*reg
drivers/net/ethernet/stmicro/stmmac/dwmac-meson.c:64:29: warning: symbol 'meson6_dwmac_data' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:354:29: warning: symbol 'stih4xx_dwmac_data' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/dwmac-sti.c:361:29: warning: symbol 'stid127_dwmac_data' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/dwmac-sunxi.c:133:29: warning: symbol 'sun7i_gmac_data' was not declared. Should it be static?
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a kernel helper to dump buffers in a hexdecimal format. This patch
substitutes the open coded function by calling that helper.
The output is slightly changed:
- no lead space
- ASCII part will be printed along with the dump
- offset is longer than 3 characters (now 8)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of pr_* macros let's use dev_* macros which provide device name.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Migrate pci driver to managed resources to reduce boilerplate error handling
code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert system PM callbacks to use dev_pm_ops. In addition remove the PCI calls
related to a power state since the bus code cares about this already.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The last standard PCI resource is defined as PCI_STD_RESOURCE_END. Thus, we
could use it instead of plain integer.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following sparse warnings.
drivers/net/ethernet/stmicro/stmmac/enh_desc.c:381:30: warning: symbol 'enh_desc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/norm_desc.c:253:30: warning: symbol 'ndesc_ops' was not declared. Should it be static?
drivers/net/ethernet/stmicro/stmmac/stmmac_hwtstamp.c:141:33: warning: symbol 'stmmac_ptp' was not declared. Should it be static?
There is no functional change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Giuseppe CAVALLARO <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the atomicity when suspend and resume the
driver. The clk api have been changed (as reported by Hao Liang)
and the skb allocation is done out of the hw setup function and
taking care about the GFP flags.
Reported-by: Hao Liang <hliang1025@gmail.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: Hao Liang <hliang1025@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch aims to fix the concurrency in eee initialization
inside the stmmac driver and related warnings when enable
DEBUG_ATOMIC_SLEEP.
Prior this patch, the stmmac_eee_init could be called in several places
as shown below:
stmmac_open stmmac_resume PHY Layer
| | |
stmmac_hw_setup stmmac_adjust_link
| | stmmac ethtool
|__________________________|______________|
|
stmmac_eee_init
The patch removes the stmmac_eee_init call inside the stmmac_hw_setup
that is unnecessary. It is sufficient to call it in the adjust_link to
always guarantee that EEE is always configured at mac level too.
Fixing the lock protection now it is covered another case (not
considered before). The stmmac_eee_init could be called by the ethtool
so critical sections must be protected inside this function too.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing spin_unlock when tx frames gets dropped.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_tx_avail() may lie if used unprotected. It's using cur_tx
and dirty_tx index. These index may be already in use by tx_clean
when entering xmit routine. So, this should be called locked.
This can cause transmit queue to be stuck, with following message:
NETDEV WATCHDOG: eth0 (stmmaceth): transmit queue 0 timed out
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a very old and often unused option to configure
a bit in a register inside the DMA. This support should
not stay under Koption and should be extended for new chips too.
This will be do later maybe via device-tree parameters.
Also no performance impact when remove this setting on STi platforms.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
the STMMAC_DEBUG_FS Koption is now removed from the
driver configuration and this support will be built
by default when DEBUG_FS is present. This can also be
useful on building driver verification.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes all the Koptions added to build the glue-logic files
for all different architectures: DWMAC_MESON, DWMAC_SUNXI, DWMAC_STI ...
Nowadays the stmmac needs to be compiled on several platforms; in some
case it very convenient to guarantee that its build is always completed
with success on all the branches where the driver is present.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 3b57de958e brought the support for a different amount of the
filter bins, but didn't update the PCI driver accordingly. This patch appends
the default values when the device is enumerated via PCI bus.
Fixes: 3b57de958e (net: stmmac: Support devicetree configs for mcast and ucast filter entries)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch is to fix the stmmac data compatibilities for
all the SoCs inside the platform file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to review the whole glue logic adopted on STi SoCs that
was bugged.
In the old glue-logic there was a lot of confusion when setup the
retiming especially for STiD127 where, for example, the bits 6 and 7
(in the GMAC control register) have a different meaning of what is
used for STiH4xx SoCs. So we cannot adopt the same glue for all these
SoCs.
Moreover, GiGa on STiD127 didn't work and, for all the SoCs, the RGMII
couldn't run when the speed was 10Mbps (because the clock was not properly
managed).
Note that the phy clock needs to be provided by the platform as well as
documented in the related binding file (updated as consequence).
The old code supported too many configurations never adopted and validated.
This made the code very complex to maintain and debug in case of issues.
The patch simplifies all the configurations as commented in the tables
inside the file and obviously it has been tested on all the boards
based on the SoCs mentioned.
With this patch, the dwmac-sti is also ready to support new configurations that
will be available on next SoC generations.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds the missing compatibility to the STiH407 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On several STi platforms: e.g. stihxxx-b2120 an Ethernet switch is
embedded and connected to the stmmac via RGMII mode. So this is managed
by using the FIXED_PHY. In that case, the support in the platform needs
to be fixed to allow the stmmac to dialog with the switch via fixed-link
by using phy_bus_name property.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Testing revealed that the local variable mc_filter was dimensioned
incorrectly for all possible configurations and get_mac_addr should
have been set_mac_addr (a typo). Make sure mc_filter is dimensioned
to 8 32-bit unsigned longs - the largest size of the Synopsys
multicast filter register set.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to call ether_setup after alloc_ethdev since it was
already called there.
Follow commits c706471b26 ("net: axienet: remove unnecessary
ether_setup after alloc_etherdev") and 3c87dcbfb3 ("net: ll_temac:
Remove unnecessary ether_setup after alloc_etherdev") and fix the
pattern in all remaining ethernet drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/r8152.c
net/netfilter/nfnetlink.c
Both r8152 and nfnetlink conflicts were simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When the CONFIG_HAVE_CLK is selected for the system, the stmmac_pci_probe
will fail with dmesg:
[ 2.167225] stmmaceth 0000:00:14.6: enabling device (0000 -> 0002)
[ 2.178267] stmmaceth 0000:00:14.6: enabling bus mastering
[ 2.178436] stmmaceth 0000:00:14.6: irq 24 for MSI/MSI-X
[ 2.178703] stmmaceth 0000:00:14.6: stmmac_dvr_probe: warning: cannot
get CSR clock
[ 2.186503] stmmac_pci_probe: main driver probe failed
[ 2.194003] stmmaceth 0000:00:14.6: disabling bus mastering
[ 2.196473] stmmaceth: probe of 0000:00:14.6 failed with error -2
This patch fix the issue by breaking the dependency to devm_clk_get()
as the CSR clock can be obtained at priv->plat->clk_csr from pci driver.
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: Kweh, Hock Leong <hock.leong.kweh@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Ethernet controller available in Meson6 and Meson8 SoCs is a
Synopsys DesignWare MAC IP core, already supported by the stmmac
driver.
This glue layer implements some platform-specific settings needed by
the Amlogic variant.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function devm_ioremap_resource() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the much more common pr_warn instead of pr_warning.
Other miscellanea:
o Typo fixes submiting/submitting
o Coalesce formats
o Realign arguments
o Add missing terminating '\n' to formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of the HW is not able to do the receive checksum offloading
the only feature to remove is NETIF_F_RXCSUM.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new GMACs it is possible to turn-on/off the COE.
In the current driver, when disabled the Rx-checksum
via ethtool, the tool reported that csum was disabled
but the HW continued to set the IPC. Indeed this is
because the fix_features allows this. So the patch
fixes this problem by adding the set_features.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of PLS is active the PLS (PHY Link Status) bit in
the Reg12 has to be set to allow the MAC to asserts the LPI
pattern when the link is ok.
Signed-off-by: nandini sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to skip the EEE initialisation when the stmmac
is using a switch (with a fixed phy support).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value for LPI TW timer has to be updated to 0x1E that is the hardcoded value
of 20.5us and it will apply to all EEE enabled Remote PHYs.
Disadvantage is for PHY's that support lesser wakeup time but we can accept it
waiting to implement LLDP to negotiate the Wakeup time of Remote PHY.
Signed-off-by: nandini sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the definition of macros for EEE otherwise the LPI TX/RX
entry/exit cannot be properly managed.
Signed-off-by: Nandini Sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warning:
drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c:122:41:
sparse: cast removes address space of expression
drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c:122:38:
sparse: incorrect type in assignment (different address spaces)
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling DMA_API_DEBUG, warnings are reported at runtime
because the device driver frees DMA memory with wrong functions
and it does not call dma_mapping_error after mapping dma memory.
The first problem is fixed by of introducing a flag that helps us
keeping track which mapping technique was used, so that we can use
the right API for unmap.
This approach was inspired by the e1000 driver, which uses a similar
technique.
Signed-off-by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Denis Kirjanov <kda@linux-powerpc.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP reference clock, used for setting the addend in the Timestamp Addend
Register, was erroneously hard-coded (as reported in the databook just as
example).
The patch removes the macro named: STMMAC_SYSCLOCK and allows to use a
reference clock (clk_ptp_ref_i) that can be passed from the platform.
If not passed, the main driver clock will be used as default; note that
this can be fine on some platforms.
Note that, prior this patch, using the old STMMAC_SYSCLOCK on some platforms,
as side effect, the ptp clock can move faster/slower than the system clock.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a typo on mmc rx crc error when reported by ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to w/a a problem that happens on some boxes when run at 10Mbps
Half duplex mode.
During the transmission the CSR signal is asserted for some time and the frames
aborted because of carrier sense error.
This is reported by MMC HW counter: txcarrier signal.
This actually is a false carrier so the frames are good and there is no reason
to ask for dropping them.
This patch so disables the Carrier Sense During Transmission
and this means that the MAC transmitter ignore the CRS signal
during frame transmission in Half-Duplex mode.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to properly put to NULL the ptp_clock while un-register the PTP support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the IPC bit into the GMAC control register
that must be done after the core initialization otherwise it will
not have any effect.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds simple cleanups for stmmac, removing test we know is always
true, fixing whitespace, and moving code out of if().
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds fix_mac_speed() support for
Altera socfpga Ethernet controller. Emac splitter is a
soft IP core in FPGA system that converts GMII interface from
Synopsys mac to RGMII/SGMII interface. This splitter core is
an optional IP if user would like to use RGMII/SGMII
interface in their system. Software needs to update a register
in splitter core when there is speed change.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should prefer `struct pci_device_id` over `DEFINE_PCI_DEVICE_TABLE` to
meet kernel coding style guidelines. This issue was reported by checkpatch.
A simplified version of the semantic patch that makes this change is as
follows (http://coccinelle.lip6.fr/):
// <smpl>
@@
identifier i;
declarer name DEFINE_PCI_DEVICE_TABLE;
initializer z;
@@
- DEFINE_PCI_DEVICE_TABLE(i)
+ const struct pci_device_id i[]
= z;
// </smpl>
[bhelgaas: add semantic patch]
Signed-off-by: Benoit Taine <benoit.taine@lip6.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
This patch adds and modifies code to support multiple Multicast and Unicast
Synopsys MAC filter configurations. The default configuration is defined to
support legacy driver behavior, which is 64 Multicast bins. The Unicast
filter code previously assumed all controllers support 32 or 16 Unicast
addresses based on controller version number, but this has been corrected
to support a default of 1 Unicast address. The filter configuration may
be specified through the devicetree using a Synopsys specific device tree
entry. This information was verified with Synopsys through
Synopsys Support Case #8000684337 and shared with the maintainer.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the check for the number of mulitcast addresses
when using hash based filtering since it's not necessary. If the number
of multicast addresses in the list exceeds the number of multicast hash
bins, the bins will "fold" over into one of the bins configured and
enabled for the particular component instance.
The default number of maximum unicast addresses was changed from 32 to 1
since this number is not dependent on the component revision. The maximum
number of multicast and unicast addresses is dependent on the configuration
of the Synopsys EMAC configured by the SOC architect at the time the
features were selected and configured for a particular component. Sadly,
Synopsys does not provide a way to query the precise number supported
by a particular component, so we must fall back on a devicetree entry.
This configuration could vary from vendor to vendor (such as STMicro,
Altera, etc).
The multicast bins are set for every possible filtering case (including
no entries) - previously the bits were set only if multicast filter entries
were present.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The synopsys EMAC can be configured for different numbers of multicast hash
bins and perfect filter entries at device creation time and there's no way
to query this configuration information at runtime. As a result, a devicetree
parameter is required in order for the driver to program these filters
correctly for a particular device instance. This patch modifies the
10/100/1000 MAC software interface such that these configuration parameters
can be set at initialization time.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 0acf167687.
Breaks the build due to missing reference to phy_resume in
the resulting dwmac-socfpga.o object.
Signed-off-by: David S. Miller <davem@davemloft.net>
Cppcheck found a case where a local variable was being assigned a value,
but not used. There seems to be no reason to read this register before
assigning a new value, so addressing thie issue.
cppcheck --force --enable=all --inline-suppr . shows ...
Variable 'value' is reassigned a value before the old one has been used.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cppcheck found a duplicate if/then/else case where a receive descriptor
was being processed. This patch corrects that issue.
cppcheck --force --enable=all --inline-suppr .
...
Checking enh_desc.c...
[enh_desc.c:148] -> [enh_desc.c:144]: (style) Found duplicate if expressions.
...
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds platform init/exit functions and modifications to support
suspend/resume for the Altera Cyclone 5 SOC Ethernet controller. The platform
exit function puts the controller into reset using the socfpga reset
controller driver. The platform init function sets up the Synopsys mac by
first making sure the Ethernet controller is held in reset, programming the
phy mode through external support logic, then deasserts reset through
the socfpga reset manager driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch moved device tree interrupt resolution into
platform_get_irq_byname:
ad69674 of/irq: do irq resolution in platform_get_irq_byname()
As a result, the function no longer only return -ENXIO on error.
This breaks DT based probing of stmmac, as seen in test runs of
linux-next next-20140526 cubie2-sunxi_defconfig:
http://lists.linaro.org/pipermail/kernel-build-reports/2014-May/003659.html
This patch makes the stmmac_platform probe function properly handle
error codes, such as returning for deferred probing, and other codes
returned by of_irq_get_by_name.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch removed unnecessary spin_lock/unlock calls
in ethtool_ops callback functions. In the second and final version
of the patch one spin_lock call was left behind.
commit cab6715c3e
Author: Yang Wei <Wei.Yang@windriver.com>
Date: Sun May 25 09:53:44 2014 +0800
net: driver: stmicro: Remove some useless the lock protection
This introduced the following sparse warning:
drivers/net/ethernet/stmicro/stmmac/stmmac_ethtool.c:424:1: warning:
context imbalance in 'stmmac_get_pauseparam' -
different lock contexts for basic block
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kernel always invokes a pair of rtnl_lock adn rtnl_unlock to
protect dev_ethtool(), so its not neccessary to invoke spin_lock/unlock
in ethtool_ops.
Signed-off-by: Yang Wei <Wei.Yang@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/bonding/bond_alb.c
drivers/net/ethernet/altera/altera_msgdma.c
drivers/net/ethernet/altera/altera_sgdma.c
net/ipv6/xfrm6_output.c
Several cases of overlapping changes.
The xfrm6_output.c has a bug fix which overlaps the renaming
of skb->local_df to skb->ignore_df.
In the Altera TSE driver cases, the register access cleanups
in net-next overlapped with bug fixes done in net.
Similarly a bug fix to send ALB packets in the bonding driver using
the right source address overlaps with cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac_open call was calling clk_disable_unprepare on phy init
failure, but it never calls clk_prepare_enable, this causes
a WARN_ON in the clk framework to trigger if for some reason phy init
fails.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net: get rid of SET_ETHTOOL_OPS
Dave Miller mentioned he'd like to see SET_ETHTOOL_OPS gone.
This does that.
Mostly done via coccinelle script:
@@
struct ethtool_ops *ops;
struct net_device *dev;
@@
- SET_ETHTOOL_OPS(dev, ops);
+ dev->ethtool_ops = ops;
Compile tested only, but I'd seriously wonder if this broke anything.
Suggested-by: Dave Miller <davem@davemloft.net>
Signed-off-by: Wilfried Klaebe <w-lkml@lebenslange-mailadresse.de>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii_irq[] array is never initialized anywhere in the driver, thus mii_irq[]
will always equate to zero. So, for the case where the PHY does not have an
irq, we should use PHY_POLL for that situation.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Tested-by: Vince Bridgers <vbridger@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_config() denies changing the base address and interrupt
parameters, and ignores any other settings from the ifmap parameters,
thus making stmmac_config() useless, remove it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the STi and sunxi series SOCs, Altera's SOCFPGA also needs a glue layer
on top of the Synopsys gmac IP.
This patch adds the platform driver for the glue layer which configures the IP
before the generic STMMAC driver takes over.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace dev_kfree_skb with dev_consume_skb_any in stmmac_tx_clean that can
be called in hard irq and other contexts. stmmac_tx_clean handles
freeing successfully transmitted packets.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
This patch updates the many PTP Hardware Clock drivers with the
newly introduced field that advertises the number of programmable
pins. Some of these devices do have programmable pins, but the
implementation will have to wait for follow on patches.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to fix the compatibility to the STiD127 SoC.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the chain mode that was broken
and generated a panic. This patch reviews the chain/ring
modes now shaing the same structure and taking care
about the pointers and callbacks.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix and tune the default buffer sizes.
It reduces the default bufsize used by the driver from
4KiB to 1536 bytes.
Patch has been tested on both ARM and SH4 platform based.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to disable the EEE (so HW and timers)
for example when the phy communicates that the EEE
can be supported anymore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc_dma_desc_resources() returns an error value and the next line
actually checks for it, so assign the return value properly.
Found by the coverity scanner.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
STi series SOCs have a glue layer on top of the synopsis gmac IP, this
glue layer needs to be configured before the gmac driver starts using
the IP.
This patch adds a support to this glue layer which is configured via
stmmac setup, init, exit callbacks.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logging the MAC address on every if-up, is not really useful, and annoying when
there is no cable inserted and NetworkManager tries the ifup every 50 seconds.
Also change the log level from warning to info, as that is what it is.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Logging a PTP error on hw which simply does not support PTP is not very
useful. Moreover this message gets logged on every if-up, and if there is
no cable inserted NetworkManager will re-try the ifup every 50 seconds.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When timestamping is enabled, stmmac_tx_clean will call
stmmac_get_tx_hwtstamp to get tx TS.
But the skb can be NULL because the last of its tx_skbuff is NULL
if this packet frame is filled in more than one descriptors.
To fix the issue, change the code:
- Store TX skb to the tx_skbuff[] of frame's last segment.
- Check skb is not NULL in stmmac_get_tx_hwtstamp.
Signed-off-by: Bruce Liu <damuzi000@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Allwinner A20 has an ethernet controller that seems to be
an early version of Synopsys DesignWare MAC 10/100/1000 Universal,
which is supported by the stmmac driver.
Allwinner's GMAC requires setting additional registers in the SoC's
clock control unit.
The exact version of the DWMAC IP that Allwinner uses is unknown,
thus the exact feature set is unknown.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver core allows passing feature flags and callbacks via
platform data. Add a similar stmmac_of_data to pass flags and callbacks
tied to compatible strings. This allows us to extend stmmac with glue
layers for different SoCs.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The snps,phy-addr device tree property is non-standard, and should be
removed in favor of proper phy node support. Remove it from the binding
documents and warn if the property is still used.
Most PHYs respond to address 0, but a few don't, so auto-detect PHY
address by default, to make up for the lack of explicit address selection.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
"snps,force_sf_dma_mode" is documented in stmmac device tree bindings,
but is never handled by the driver.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current .init and .exit callbacks requires access to driver
private data structures. This is not a good seperation and abstraction.
Instead, we add a new .setup callback for allocating private data, and
pass the returned pointer to the other callbacks.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DWMAC has a reset assert line, which is used on some SoCs. Add an
optional reset control to stmmac driver core.
To support reset control deferred probing, this patch changes the driver
probe function to return the actual error, instead of just -EINVAL.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The stmmac driver does not enable the main clock during the probe phase.
If the clock was not enabled by the boot loader or was disabled by the
kernel, hardware features and the MDIO bus would not be probed properly.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In PM_SUSPEND_FREEZE and WOL(Wakeup On Lan) case, when the driver gets a
wakeup event, either the driver or platform specific PM code should notify
the pm core about it, so that the system can wakeup from low power.
In cases where there is no involvement of platform specific PM, it
becomes driver responsibility to notify the PM core to wakeup the
system.
Without this WOL with PM_SUSPEND_FREEZE does not work on STi based SOCs.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to restore default pinstate of the pins when it
comes back from low power state. Without this patch the state of the
pins would be unknown and the driver would not work.
This patch also adds code to put the pins in to sleep state when the
driver enters low power state.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In hibernation freeze case the driver just releases the resources like
dma buffers, irqs, unregisters the drivers and during restore it does
register, request the resources. This is not really necessary, as part
of power management all the data structures are intact, all the
previously allocated resources can be used after coming out of low
power.
This patch uses the suspend and resume callbacks for freeze and
restore which initializes the hardware correctly without unregistering
or releasing the resources, this should also help in reducing the time
to restore.
Also this patch fixes a bug in stmmac_pltfr_restore and
stmmac_pltfr_freeze where it tries to get hold of platform data via
dev_get_platdata call, which would return NULL in device tree cases and
the next if statement would crash as there is no NULL check.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver PM resume assumes that the IP is still powered up and the
all the register contents are not disturbed when it comes out of low
power suspend case. This assumption is wrong, basically the driver
should not consider any state of registers after it comes out of low
power. However driver can keep the part of the IP powered up if its a
wake up source. But it can not assume the register state of the IP. Also
its possible that SOC glue layer can take the power off the IP if its
not wake-up source to reduce the power consumption.
This patch re initializes hardware by calling stmmac_hw_setup function in
resume case.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch promotes stmmac_mdio_reset function from static to
non-static, so that power management functions can decide to reset if
the IP comes out from lowe power state specially hibernation cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves hardware setup part of the code in stmmac_open to a new
function stmmac_hw_setup, the reason for doing this is to make hw
initialization independent function so that PM functions can re-use it to
re-initialize the IP after returning from low power state.
This will also avoid code duplication across stmmac_resume/restore and
stmmac_open.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves dma resource allocation to a new function
alloc_dma_desc_resources, the reason for moving this to a new function
is to keep the memory allocations in a separate function. One more reason
it to get suspend and hibernation cases working without releasing and
allocating these resources during suspend-resume and freeze-restore
cases.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes gpio_free for reset line of the phy, driver stores
the gpio number in its private data-structure to use in future. As the
driver uses this pin in future this pin should not be freed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to "max-speed" property which is a standard
Ethernet device tree property. max-speed specifies maximum speed
(specified in megabits per second) supported the device.
Depending on the clocking schemes some of the boards can only support
few link speeds, so having a way to limit the link speed in the mac
driver would allow such setups to work reliably.
Without this patch there is no way to tell the driver to limit the
link speed.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.
This covers everything under drivers/net except for wireless, which
has been submitted separately.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GRO requires VLANs to be removed before aggregation can occur.
The Synopsys EMAC does not strip VLAN tags so this must be
done by the driver.
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c
net/ipv6/ip6_tunnel.c
net/ipv6/ip6_vti.c
ipv6 tunnel statistic bug fixes conflicting with consolidation into
generic sw per-cpu net stats.
qlogic conflict between queue counting bug fix and the addition
of multiple MAC address support.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make variables only used in one file static. Also avoids possible
namespace collisions.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a problem in stmmac_ptp.c, functions
stmmac_adjust_time and stmmac_adjust_freq where the incorrect spinlocks
were released. This patch also addresses a problem in stmmac_main,
function stmmac_init_ptp where the capability detection for
advanced timestamping was masked by message masking.
This patch was touch tested using linuxptp, and runs without the previously
observed instabilities. More extensive testing is ongoing.
Vince
Signed-off-by: Vince Bridgers <vbridgers2013@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch marks the function stmmac_pltfr_freeze() and
stmmac_pltfr_restore() in stmmac_platform.c as static because they are
not used outside this file.
Thus, it also removes the following warnings in
ethernet/stmicro/stmmac/stmmac_platform.c:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:222:5: warning: no previous prototype for ‘stmmac_pltfr_freeze’ [-Wmissing-prototypes]
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:236:5: warning: no previous prototype for ‘stmmac_pltfr_restore’ [-Wmissing-prototypes]
Signed-off-by: Rashika Kheria <rashika.kheria@gmail.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
stmmac_hwtstamp_ioctl() should validate all fields of hwtstamp_config
before making any changes. Currently it sets the TX configuration
before validating the rx_filter field.
Compile-tested only.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a mix of function prototypes with and without extern
in the kernel sources. Standardize on not using extern for
function prototypes.
Function prototypes don't need to be written with extern.
extern is assumed by the compiler. Its use is as unnecessary as
using auto to declare automatic/local variables in a block.
Signed-off-by: Joe Perches <joe@perches.com>
Merge commit 06c54055be did a bad conflict resolution accidentally
leaving out a closing brace. Add it back.
This breaks a handful of defconfigs on ARM, so it'd be good to see it
applied pretty quickly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
The synopsys spec says When TSCRLSSR is cleard, the rollover value of
sub-second register is 0x7FFFFFFF(0.465 ns per clock).
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some synopsys ip implementation doesn't support DMA store and forward mode,
such as BF60x. So, set force_thresh_dma_mode to use DMA thresholds only.
Update document and devicetree as well.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the pbl(programmable burst length) setting
using DT. Even though the default pbl is 8, If there is no
pbl property in device tree file, pbl is set 0 and it causes
bandwidth degradation.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the no_csum_insertion private parameter that is not used anymore
and, also, the "likely" annotation from the condition that is not in a critical path.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In stmmac_init_rx_buffers():
* add missing handling of dma_map_single() error
* remove superfluous unlikely() optimization while at it
Add stmmac_free_rx_buffers() helper and use it in dma_free_rx_skbufs().
In init_dma_desc_rings():
* add missing handling of kmalloc_array() errors
* fix handling of dma_alloc_coherent() and stmmac_init_rx_buffers() errors
* make function return an error value on error and 0 on success
In stmmac_open():
* add handling of init_dma_desc_rings() return value
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed the condition of extend_desc for jumbo frame.
There is no check routine for extend_desc in the stmmac_jumbo_frm function.
Even though extend_desc is set if dma_tx is used instead of dma_etx.
It causes kernel panic.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds phy reset callback support for stmmac driver via device
trees. It adds three new properties to gmac device tree bindings to
define the reset signal via gpio.
With this patch users can conveniently pass reset gpio number with pre,
pulse and post delay in micro secs via DTs.
active low:
_________ ____________
<pre-delay> |<pulse-delay> |<post-delay>
| |
|_______________|
active high:
________________
<pre-delay> |<pulse-delay> |<post-delay>
| |
________| |___________
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds dt support to dwmac version 3.610 and 3.710 these
versions are integrated in STiH415 and STiH416 ARM A9 SOCs.
To support these IP version, some of the device tree properties are
extended.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some DT use-cases platform data might be already allocated and passed
via AUXDATA. These are the cases where machine level code populates few
callbacks in the platform data.
This patch adds check and reuses platform_data if its valid, before
allocating a new one.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a memory leak in the open method, it reviews error
conditions freeing the resources previously allocated and not freed in
cased of DMA failure.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/freescale/fec_main.c
drivers/net/ethernet/renesas/sh_eth.c
net/ipv4/gre.c
The GRE conflict is between a bug fix (kfree_skb --> kfree_skb_list)
and the splitting of the gre.c code into seperate files.
The FEC conflict was two sets of changes adding ethtool support code
in an "!CONFIG_M5272" CPP protected block.
Finally the sh_eth.c conflict was between one commit add bits set
in the .eesr_err_check mask whilst another commit removed the
.tx_error_check member and assignments.
Signed-off-by: David S. Miller <davem@davemloft.net>
Prior this patch, the internal debugging was based on ifdef
and also some printk were useless because many info are exposed
via ethtool.
This patch remove all the ifdef defines and now we only use
netif_msg_XXX levels.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed that enh_desc value is always zero.
Due to calling order of stmmac_selec_desc_mode(), enh_desc value is always zero.
Even though mac is set to use enhanced dma descriptor, if enh_desc is zero,
functions related dma descriptor are not working correctly.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixed operator typo from & to ==.
Due to incorrect operator, the result is incorrect.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers that select MII also need to select NET_CORE because MII
depends on it. This is a bit ridiculous because NET_CORE is just a
menu option that doesn't enable any code by itself.
There is also no need for it to be a visible option, since its users
all select it.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the EEE setup allowing to configure this support
when the link changes.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c: In function:
stmmac_xmit drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1902:74:
error: expected ) before __func__
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure, since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound).
Thus, it is not needed to manually clear the device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Roland Stigge <stigge@antcom.de>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Tested-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `dma_free_tx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1141: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `dma_free_rx_skbufs':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1120: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `free_dma_desc_resources':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1159: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `stmmac_init_rx_buffers':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:980: undefined reference to `dma_map_single'
drivers/built-in.o: In function `init_dma_desc_rings':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1015: undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `stmmac_tx_clean':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1250: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2044: undefined reference to `dma_unmap_single'
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2082: undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `stmmac_rx_refill':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1967: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_xmit':
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:1845: undefined reference to `dma_map_single'
drivers/built-in.o: In function `skb_frag_dma_map':
include/linux/skbuff.h:2184: undefined reference to `dma_map_page'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/ring_mode.c:40: undefined reference to `dma_map_single'
drivers/built-in.o: In function `stmmac_jumbo_frm':
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:48: undefined reference to `dma_map_single'
drivers/net/ethernet/stmicro/stmmac/chain_mode.c:55: undefined reference to `dma_map_single'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert use of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
devm_ioremap_resource() provides its own error messages so all explicit
error messages can be removed from the failure code paths.
This was found with coccinelle.
Signed-off-by: Silviu-Mihai Popescu <silviupopescu1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the DesignWare MAC is synthesised with MMC RX IPC Counter, an unmanaged
and unacknowledged interrupt is generated after some time of operation.
This patch masks the undesired interrupts.
Signed-off-by: Christian Ruppert <christian.ruppert@abilis.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to prefetch, in the stmmac_rx, the whole
dma_erx descriptor in case of using the extended descriptors.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
recently many new supports have been added in the stmmac driver w/o taking care
about where each new field had to be placed inside the private structure for
guaranteeing the best cache usage.
This is what I wanted in the beginning, so this patch reorganizes all the fields
in order to keep adjacent fields for cache effect.
I have also tried to optimize them by using pahole.
V2: do not abuse with ____cacheline_aligned_in_smp and keep fields that
potentially could stay in the same cache-line for better usage in SMP systems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch tidies up the code. I have run Linden (and verified with checkpatch)
many part of the driver trying to reorganize some sections respecting the
codying-style rules in the points where it was not done.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch reviews/improves and adds some fixes in the code doc.
Also kernel-doc passes w/o any warnings.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch modifies the pcs mode support for SGMII. Even though
SGMII does auto-negotiation with phy, it needs stmmac_init_phy and
stmmac_mdio_register function for initializing phy.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the stmmac.txt file adding information related to the PTP
and SGMII/RGMII supports.
Also the patch updates the driver version to: March_2013.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements PHC (ptp hardware clock) driver for stmmac
driver to support 1588 PTP.
V2: added support for FINE method, reduced loop delay and review spinlock.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enhances the stmmac driver to support IEEE 1588-2002
PTP (Precision Time Protocol) version 1 and IEEE 1588-2008 PPT
version 2.
Precision Time Protocol(PTP),which enables precise synchronization
of clocks in measurement and control systems implemented with
technologies such as network communication,local computing,
& distributed objects.
Both PTPv1 and PTPv2 is selected at run-time using the HW capability
register.
The PTPv1 TimeStamp support can be used on chips that have the normal
descriptor structures and PTPv2 TimeStamp support can be used on chips
that have the Extended descriptors(DES4-5-6-7). All such sanity checks
are done and verified by using HW capability register.
V2: in this version the ethtool support has been included in this patch;
Koptions have been completely removed (previously added to select
PTP and PTPv2). PTPv1 and PTPv2 is now added in a single patch instead of
two patches.
get_timestamp() and get_systemtime() L/H have been combined into single APIs.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new pointer variable called "tx_skbuff_dma" to private
data structure. This variable will holds the physical address of packet
to be transmitted & same will be used to free/unmap the memory once the
corresponding packet is transmitted by device.
Prior to this patch the descriptor buffer pointer(ie des2) itself was
being used for freeing/unmapping the buffer memory. But in case PTP v1
with normal descriptor the field(des2) will be overwritten by device
with timestamp value, hence driver will loose the buffer pointer to be
freed/unmapped.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the minimal support to manage the PCS
modes (RGMII/SGMII) and restart the ANE.
Both TBI and RTBI are not yet supported.
Thanks to Byungho that wrote some part of this code
and tested SGMII too.
The only thing to be fixed is the get/set pause in
ethtool.
Signed-off-by: Byungho An <bh74.an@samsung.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch starts adding in the main ISR the management of the PCS and
RGMII/SGMII core interrupts. This is to help further development
on this area. Currently the core irq handler only clears the
PCS and S-R_MII interrupts and reports the event in the ethtool stats.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Tested-by: Byungho An <bh74.an@samsung.com>
Cc: Udit Kumar <udit-dlh.kumar@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to support the extend descriptors available
in the chips newer than the 3.50.
In case of the extend descriptors cannot be supported,
at runtime, the driver will continue to work using the old style.
In detail, this support extends the main descriptor structure
adding new descriptors: 4, 5, 6, 7. The desc4 gives us extra
information about the received ethernet payload when it is
carrying PTP packets or TCP/UDP/ICMP over IP packets.
The descriptors 6 and 7 are used for saving HW L/H timestamps (PTP).
V2: this new version removes the Koption added in the first implementation
because all the checks now to verify if the extended descriptors are
actually supported happen at probe time.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously we had two Koptions to decide if the stmmac
had to use either a ring or a chain to manage its descriptors.
This patch removes the Kernel configuration options and it allow us
to use the chain mode by passing a module option.
Ring mode continues to be the default.
Also with this patch, it will be easier to validate the driver built and
guarantee that all the two modes always compile fine.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I believe these error messages are already logged
on allocation failure by warn_alloc_failed and so
get a dump_stack on OOM.
Remove the unnecessary additional error logging.
Around these deletions:
o Alignment neatening.
o Remove unnecessary casts of dma_alloc_coherent.
o Hoist assigns from ifs.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers all
over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
If you need me to provide a merged tree to handle these resolutions,
please let me know.
Other than those patches, there's not much here, some minor fixes and
updates.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlEmV0cACgkQMUfUDdst+yncCQCfbmnQZju7kzWXk6PjdFuKspT9
weAAoMCzcAtEzzc4LXuUxxG/sXBVBCjW
=yWAQ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg Kroah-Hartman:
"Here is the big driver core merge for 3.9-rc1
There are two major series here, both of which touch lots of drivers
all over the kernel, and will cause you some merge conflicts:
- add a new function called devm_ioremap_resource() to properly be
able to check return values.
- remove CONFIG_EXPERIMENTAL
Other than those patches, there's not much here, some minor fixes and
updates"
Fix up trivial conflicts
* tag 'driver-core-3.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (221 commits)
base: memory: fix soft/hard_offline_page permissions
drivercore: Fix ordering between deferred_probe and exiting initcalls
backlight: fix class_find_device() arguments
TTY: mark tty_get_device call with the proper const values
driver-core: constify data for class_find_device()
firmware: Ignore abort check when no user-helper is used
firmware: Reduce ifdef CONFIG_FW_LOADER_USER_HELPER
firmware: Make user-mode helper optional
firmware: Refactoring for splitting user-mode helper code
Driver core: treat unregistered bus_types as having no devices
watchdog: Convert to devm_ioremap_resource()
thermal: Convert to devm_ioremap_resource()
spi: Convert to devm_ioremap_resource()
power: Convert to devm_ioremap_resource()
mtd: Convert to devm_ioremap_resource()
mmc: Convert to devm_ioremap_resource()
mfd: Convert to devm_ioremap_resource()
media: Convert to devm_ioremap_resource()
iommu: Convert to devm_ioremap_resource()
drm: Convert to devm_ioremap_resource()
...
Pull in 'net' to take in the bug fixes that didn't make it into
3.8-final.
Also, deal with the semantic conflict of the change made to
net/ipv6/xfrm6_policy.c A missing rt6->n neighbour release
was added to 'net', but in 'net-next' we no longer cache the
neighbour entries in the ipv6 routes so that change is not
appropriate there.
Signed-off-by: David S. Miller <davem@davemloft.net>
This pacth fixes the parsing of the eee_timer driver parameter.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c
The bnx2x gso_type setting bug fix in 'net' conflicted with
changes in 'net-next' that broke the gso_* setting logic
out into a seperate function, which also fixes the bug in
question. Thus, use the 'net-next' version.
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch the stmmac fails in case of the phy device
is not found; w/o this fix the mdio can be register twice when
do down/up the iface and this is not correct.
Reported-by: Stas <stsp@list.ru>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the name of the macro used for
debugging the transmit process. I used STMMAC_TX_DEBUG
instead of STMMAC_XMIT_DEBUG.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
alloc failures already get standardized OOM
messages and a dump_stack.
Convert kzalloc's with multiplies to kcalloc.
Convert kmalloc's with multiplies to kmalloc_array.
Fix a few whitespace defects.
Convert a constant 6 to ETH_ALEN.
Use parentheses around sizeof.
Convert vmalloc/memset to vzalloc.
Remove now unused size variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If stmmac_dvr_probe() fails in stmmac_pci_probe(), it breaks off initialization,
deallocates all resources, but returns zero.
The patch adds -ENODEV as return value in this case.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Acked-by: David S. Miller <davem@davemloft.net>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The flags argument of the phy_{attach,connect,connect_direct} functions
is then used to assign a struct phy_device dev_flags with its value.
All callers but the tg3 driver pass the flag 0, which results in the
underlying PHY drivers in drivers/net/phy/ not being able to actually
use any of the flags they would set in dev_flags. This patch gets rid of
the flags argument, and passes phydev->dev_flags to the internal PHY
library call phy_attach_direct() such that drivers which actually modify
a phy device dev_flags get the value preserved for use by the underlying
phy driver.
Acked-by: Kosta Zertsekel <konszert@marvell.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strlcpy where possible to ensure the string is \0 terminated.
Use always sizeof(string) instead of 32, ETHTOOL_BUSINFO_LEN
and custom defines.
Use snprintf instead of sprint.
Remove unnecessary inits of ->fw_version
Remove unnecessary inits of drvinfo struct.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes platform device drivers unregistering and adds proper error
handing on module loading.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The __dev* removal patches for the network drivers ended up messing up
the function prototypes for a bunch of drivers. This patch fixes all of
them back up to be properly aligned.
Bonus is that this almost removes 100 lines of code, always a nice
surprise.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlC9COEACgkQMUfUDdst+ykOEgCeKZsrtKrbjMFM5jEROqnk33FI
SwEAoMSZWFJ7M1/27FGRkylmmypWXi/p
=HH3A
-----END PGP SIGNATURE-----
Merge tag 'dev_removal' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/net-next
Networking: Remove __dev* markings from the networking drivers
This is a series of patches that remove the dev* attributes for all
networking drivers, with the exception of wireless drivers, those are in
a different branch.
Use of __devinit, __devexit_p, __devinitdata, __devinitconst, and
__devexit are no longer needed since CONFIG_HOTPLUG is being removed as
an option.
Note, there are some devinit compiler section mismatch warnings due to
this series, but they are fixed up when merged with my driver-next
branch, which fixes the PCI device id warnings, and removes the modpost
detection, as it's no longer needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Two macros have been defined twice, remove them.
Signed-off-by: Liming Wang <walimisdev@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many new feauture have been introduced in the driver:
ethtool coalesce options, Rx HW watchdog... so this patch updates the
driver's version.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to get/set the tx/rx coalesce parameters
via ethtool interface.
Tests have been done on several platform with different GMAC chips w/o and w/
RX watchdog feature.
V2: reject coalesce settings that are not supported.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GMAC devices newer than databook 3.40 has an embedded timer
that can be used for mitigating the number of interrupts.
So this patch adds this optimizations.
At any rate, the Rx watchdog can be disable (on bugged HW) by
passing from the platform the riwt_off field.
In this implementation the rx timer stored in the Reg9 is fixed
to the max value. This will be tuned by using ethtool.
V2: added a platform parameter to force to disable the rx-watchdog
for example on new core where it is bugged.
V3: do not disable NAPI when Rx watchdog is used.
V4: a new extra statistic field has been added to show the early
receive status in the interrupt handler.
This patch also adds an extra check to avoid to call
napi_schedule when the DMA_INTR_ENA_RIE bit is disabled in the
Interrupt Mask register.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new schema used for mitigating the
number of transmit interrupts.
It is based on a SW timer and a threshold value.
The timer is used to periodically call the stmmac_tx_clean
function; the threshold is used for setting the IC (Interrupt
on Completion bit). The ISR will then invoke the poll method.
Also the patch improves some ethtool stat fields.
V2: review the logic to manage the IC bit in the TDESC
that was bugged because it didn't take care about the
fragments. Also fix the tx_count_frames that has not to be
limited to TX DMA ring. Thanks to Ben Hutchings.
V3: removed the spin_lock irqsave/restore as D. Miller suggested.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TIMER option is not longer supported and this
code can be considered dead for this driver in
the new kernel series.
In fact, It was not updated at all and never used.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Over time, skb recycling infrastructure got litle interest and
many bugs. Generic rx path skb allocation is now using page
fragments for efficient GRO / TCP coalescing, and recyling
a tx skb for rx path is not worth the pain.
Last identified bug is that fat skbs can be recycled
and it can endup using high order pages after few iterations.
With help from Maxime Bizon, who pointed out that commit
87151b8689 (net: allow pskb_expand_head() to get maximum tailroom)
introduced this regression for recycled skbs.
Instead of fixing this bug, lets remove skb recycling.
Drivers wanting really hot skbs should use build_skb() anyway,
to allocate/populate sk_buff right before netif_receive_skb()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/team/team.c
drivers/net/usb/qmi_wwan.c
net/batman-adv/bat_iv_ogm.c
net/ipv4/fib_frontend.c
net/ipv4/route.c
net/l2tp/l2tp_netlink.c
The team, fib_frontend, route, and l2tp_netlink conflicts were simply
overlapping changes.
qmi_wwan and bat_iv_ogm were of the "use HEAD" variety.
With help from Antonio Quartulli.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue introduced by commit ID 6a81c26f
[net/stmmac: remove conditional compilation of clk code], which
switched from the internal stmmac_clk_{en}{dis}able calls to
clk_{en}{dis}able. By this, calling clk_prepare and clk_unprepare
was removed.
clk_{un}prepare is mandatory for platforms using common clock framework.
Since these drivers are used by SPEAr platform, which supports common
clock framework, add clk_{un}prepare() support for them. Otherwise
the clocks are not correctly en-/disabled and ethernet support doesn't
work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function clk_get() returns ERR_PTR()
and never returns NULL pointer. The NULL test in the error
handling should be replaced with IS_ERR().
dpatch engine is used to auto generated this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves calls to ioremap and request_mem_region to
devm_request_and_ioremap call.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes bus_id from mdio platform data, The reason to remove
bus_id is, stmmac mdio bus_id is always same as stmmac bus-id, so there
is no point in passing this in different variable.
Also stmmac ethernet driver connects to phy with bus_id passed its
platform data.
So, having single bus-id is much simpler.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a basic check in stmmac_mdio_unregister to see if mdio
bus registeration for this driver was actually sucessfull or not.
Use case here is, if BSP considers using mdio-gpio bus along with stmmac
driver by passing mdio_bus_data as NULL in platform data.
Call to stmmac_mdio_register with mdio_bus_data as NULL returns 0, which
is a considered sucessfull call form stmmac. Then again when we unload
the driver we just call stmmac_mdio_unregister, this is were the actual
problem is stmmac-mdio code dont really know at this instance of calling
that stmmac_mdio_register was actually successful.
So Adding a check in stmmac_mdio_unregister is always safe.
Without this patch stmmac driver calls stmmac_mdio_register from
stmmac_release which Segfaults as mii bus was never registered at the
first point.
Originally the this bug was found when unloading an stmmac driver
instance which uses mdio-gpio for smi access.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds "#ifndef __<header>_H" for protecting header from double
inclusion.
Signed-off-by: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the name of the macro used to mask the
mmc interrupt: erroneously it was used: MMC_DEFAUL_MASK.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Erroneously the DWMAC_CORE_3_40 was set to 34 instead of 0x34.
This can generate problems when run on old chips because
the driver assumes that there are the extra 16 regs available
for perfect filtering.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When getting clock, give a chance to the CPUs without DT support,
which use Common Clock Framework, such as Loongson1B.
Signed-off-by: Kelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver probe functions are generally __devinit so they will be
discarded after initialization for non-hotplug kernels.
This was found by a new warning after patch 6a228452d "stmmac: Add
device-tree support" adds a new __devinit function that is called
from stmmac_pltfr_probe.
Without this patch, building socfpga_defconfig results in:
WARNING: drivers/net/ethernet/stmicro/stmmac/stmmac.o(.text+0x5d4c): Section mismatch in reference from the function stmmac_pltfr_probe() to the function .devinit.text:stmmac_probe_config_dt()
The function stmmac_pltfr_probe() references
the function __devinit stmmac_probe_config_dt().
This is often because stmmac_pltfr_probe lacks a __devinit
annotation or the annotation of stmmac_probe_config_dt is wrong.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
With addition of dummy clk_*() calls for non CONFIG_HAVE_CLK cases in
clk.h, there is no need to have clk code enclosed in #ifdef
CONFIG_HAVE_CLK, #endif macros.
This also fixes error paths of probe(), as a goto is required in this
patch.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: viresh kumar <viresh.linux@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Because there are multiple variants to the stmmac/dwmac driver, the
dts bindings should be updated to include version of the IP used.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/batman-adv/bridge_loop_avoidance.c
net/batman-adv/bridge_loop_avoidance.h
net/batman-adv/soft-interface.c
net/mac80211/mlme.c
With merge help from Antonio Quartulli (batman-adv) and
Stephen Rothwell (drivers/net/usb/qmi_wwan.c).
The net/mac80211/mlme.c conflict seemed easy enough, accounting for a
conversion to some new tracing macros.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches. Delete
a few that are content-free.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the higher mtu sizes requiring the buffer size greater than 8192,
the buffers are sent or received using multiple dma descriptors/ same
descriptor with option of multi buffer handling.
It was observed during tests that the driver was missing on data
packets during the normal ping operations if the data buffers being used
catered to jumbo frame handling.
The memory barrriers are added in between preparation of dma descriptors
in the jumbo frame handling path to ensure all instructions before
enabling the dma are complete.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It was observed that during multiple reboots nfs hangs. The status of
receive descriptors shows that all the descriptors were in control of
CPU, and none were assigned to DMA.
Also the DMA status register confirmed that the Rx buffer is
unavailable.
This patch adds the fix for the same by adding the memory barriers to
ascertain that the all instructions before enabling the Rx or Tx DMA are
completed which involves the proper setting of the ownership bit in DMA
descriptors.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the Energy Efficient Ethernet support to the stmmac.
Please see the driver's documentation for further details about this support
in the driver.
Thanks also goes to Rayagond Kokatanur for his first implementation.
Note:
to clearly manage and expose the lpi interrupt status and eee ethtool
stats I've had to do some modifications to the driver's design and I
found really useful to move other parts of the code (e.g. mmc irq stat)
in the main directly. So this means that some core has been reworked
to introduce the EEE.
v1: initial patch
v2: fixed some sparse issues (typos)
v3: erroneously sent the v2 renamed as v3
v4:
o Fixed the return value of the stmmac_eee_init as suggested by D.Miller
o Totally reviewed the ethtool support for EEE
o Added a new internal parameter to tune the SW timer for TX LPI.
v5: do not change any eee setting in case of the stmmac_ethtool_op_set_eee fails
(it has to return -EOPNOTSUPP in that case).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch replaces the obsolete strict_strtoul with kstrtoint.
v2: also removed casting on kstrtoul.
v3: use kstrtoint instead of kstrtoul due to all vars are integer.
thanks to E. Dumazet.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_{un}prepare is mandatory for platforms using common clock framework.
Since these drivers are used by SPEAr platform, which supports common
clock framework, add clk_{un}prepare() support for them. Otherwise
the clocks are not correctly en-/disabled and ethernet support doesn't
work.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit ba27ec66ff fixes the Kconfig of the
driver when built as module allowing to select/unselect
the PCI and Platform modules that are not anymore mutually
exclusive. This patch fixes and guarantees that the driver
builds on all the platforms w/ w/o PCI and when select/unselect
the two stmmac supports. In case of there are some problems
on both the configuration and the pci/pltf registration the
module_init will fail.
v2: set the CONFIG_STMMAC_PLATFORM enabled by default.
I've just noticed that this can actually help on
some configurations that don't enable any STMMAC
options by default (e.g. SPEAr).
v3: change printk level when do not register the driver.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patches fixes the driver when built as dynamic module.
In fact, the platform part cannot be built and the probe fails
(thanks to Bob Liu that reported this bug).
v2: as D. Miller suggested, it is not necessary to make the
pci and the platform code mutually exclusive.
Having both could also help, at built time ,to verify that
all the code is validated and compiles fine.
v3: removed wrong Reviewed-by from the patch
Reported-by: Bob Liu <lliubbo@gmail.com>
cc: Rayagond Kokatanur <rayagond@vayavyalabs.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
A function in atl1e_main.c was passed a const pointer
when it actually modified elements of the structure.
Change the argument to a non-const pointer.
A function in stmmac needed a __force to avoid a sparse
warning. Added it.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes two useless initialisations in the
stmmac_rx and stmmac_tx functions.
In the former, the count variable was reset twice and in
the stmmac_tx we only need to increment the dirty pointer
w/o setting the entry variable.
v2: review the subject and comment that was not clear in my
first version.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use single_release() instead of seq_release() to free memory allocated
by single_open().
Signed-off-by: Djalal Harouni <tixxdz@opendz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon resume from standby, there is a possible interrupt
unsafe locking scenario raised when configure the Kernel
with CONFIG_PROVE_LOCKING. So this patch fixes that in
PM driver stuff by calling lock/unlock_irqsave/restore.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In mixed burst (MB) mode, the AHB master always initiates
the bursts with fixed-size when the DMA requests transfers
of size less than or equal to 16 beats.
This patch adds the MB support and the flag that can be
passed from the platform to select it.
MB mode can also give some benefits in terms of performances
on some platforms.
v2: fixed Coding Style
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to extend the number of MAC address registers
for 16 to 32. In fact, other new 16 registers are available in new
chips and this can help on perfect filter mode for unicast.
This patch also fixes the perfect filtering mode by setting the
bit 31 in the MAC address registers.
v2: fixed Coding Style.
Signed-off-by: Gianni Antoniazzi <gianni.antoniazzi-ext@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some platforms, for example where we are doing the bring-up,
the csr clock is not passed from the framework and the Ethernet
device driver is failing when it can work w/o any issues and
using the default values. So this patch just warnings the case
of the csr clock cannot be acquired but w/o failing the probe
step. I have just tested it on ST STiH415 SoC (ARM).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently the dma parameters that can be passed from the platform
have been moved from the plat_stmmacenet_data to the stmmac_dma_cfg.
In case of this new structure is not well allocated the driver can
fails. This is an example how this field is managed in ST platforms
static struct stmmac_dma_cfg gmac_dma_setting = {
.pbl = 32,
};
static struct plat_stmmacenet_data stih415_ethernet_platform_data[] = {
{
.dma_cfg = &gmac_dma_setting,
.has_gmac = 1,
[snip]
This patch so verifies that the dma_cfg passed from the platform.
In case of it is NULL there is no reason that the driver has to fail
and some default values can be passed. These are ok for all the
Synopsys chips and could impact on performances, only.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
cc: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the mdio_register/_unregister in probe/remove
functions and this also is required when hibernation on disk
is done.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st,com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st,com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freeze and restore can call the custom init/exit functions.
Also the patch adds a custom data field that can be used
for storing platform data useful on restore the embedded
setup (e.g. GPIO, SYSCFG).
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a specific clk_csr value is passed from the platform
this means that the CSR Clock Range selection cannot be
changed at run-time and it is fixed (as reported in the driver
documentation). Viceversa the driver will try to set the MDC
clock dynamically according to the actual clock input.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: David Laight <david.laight@aculab.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The CSR Clock Range has been reworked and new macros has
been added in the platform header to allow the CSR Clock
Range selection in the GMII Address Register.
The previous work didn't add the other fields
that can be used to achieve MDC clock of frequency
higher than the IEEE 802.3 specified frequency limit
of 2.5 MHz and program a clock divider of lower value.
On such platforms, these are used indeed so this patch
adds them.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
this patch adds the way to enable/disable the MAC
clock when call the open/close and resume/restore
functions.
This has been tested on ST platforms and SPEAr; thanks
to Francesco and Deepak.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Tested-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the infinite waits from the mdio read and
write interfaces. These infinite waits have been replaced by
the timeout handling. In case if a time out occurs, an error is
returned.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch re-works the internal GMAC DMA parameters
passed from the platform.
In the past, we only passed the pbl but, with new core,
other parameters can be passed and are mandatory on some
platforms.
New parameters are documented in stmmac.txt because this
patch has an impact for many platforms.
Signed-off-by: Shiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sanities the RX coe and adds the Type-1 Rx checksum offload engine (COE).
So the RX COE can be passed through the platform but can be fixed
at run-time in case of the core has the HW capability register.
Also to support the Type-1 Rx COE the driver must append the
HW checksum at the end of payload in case the Rx checksum
engine was used to offload the HW checksum.
This v2 version also fixes the IPC that has to be enabled and verified.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Hacked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As stmmac mdio bus name prefix is hardcoded in the driver, this allows
only phys on stmmac mdio buses to connect, however stmmac should allow
phys on other mdio buses too.
This patch adds new variable phy_bus_name to plat_stmmacenet_data
struct to let the BSP decide which phy bus to be used by stmmac driver.
A typical use-case is to have generic MDIO buses like mdio-gpio on top
of stmmac.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit (bfab27a stmmac: add the experimental PCI support) the
IFF_UNICAST_FLT flag has been removed from the stmmac_mac_device_setup()
function. This patch re-adds the flag.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to configure the STMMAC ethernet driver via
device-tree instead of platform_data.
Currently, only the properties needed on SPEAr600 are provided. All
other properties should be added once needed on other platforms.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_stats.c
Small minor conflict in bnx2x, wherein one commit changed how
statistics were stored in software, and another commit
fixed endianness bugs wrt. reading the values provided by
the chip in memory.
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace usage of random_ether_addr() with eth_hw_addr_random()
to set addr_assign_type correctly to NET_ADDR_RANDOM.
Change the trivial cases.
v2: adapt to renamed eth_hw_addr_random()
Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves the MAC HW initialization and
the HW feature verification from the open to the probe
function as D. Miller suggested.
So the patch actually reorganizes and tidies-up some parts of
the driver and indeed fixes some problem when tune its HW features.
These can be overwritten by looking at the HW cap register at
run-time and that generated problems.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of we use an external Wake-Up IRQ line
(priv->wol_irq != dev->irq) we need to invoke the
request_irq.
Signed-off-by: Francesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If this bit is set and the CRC error is reset, then the packet is valid.
Only report this as stat info.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling "drivr" to "driver" in
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct spelling "regiser" to "register" in
drivers/net/ethernet/stmicro/stmmac/stmmac_pci.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
