Due to timing issues in the HW, some of the status bits required for GuC
authentication occasionally don't get set; when that happens, the GuC
cannot be initialized and we will be left with a wedged GPU. The W/A
suggested is to perform a soft reset of the GuC and attempt to reload
the F/W again for few times before giving up.
As the failure is dependent on timing, tests performed by triggering
manual full gpu reset (i915_wedged) showed that we could sometimes hit
this after several thousand iterations, but sometimes tests ran even
longer without any issues. Reset and reload mechanism proved helpful
when we indeed hit f/w load failure, so it is better to include this
to improve driver stability.
This change implements the following WAs,
WaEnableuKernelHeaderValidFix:skl,bxt
WaEnableGuCBootHashCheckNotSet:skl,bxt
Signed-off-by: Arun Siluvery <arun.siluvery@linux.intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Having provided for_each_engine_id() for cases where the third (id)
argument is useful, we can now replace all the remaining instances with
a simpler version that takes only two parameters. In many cases, this
also allows the elimination of the local variable used in the iterator
(usually 'i').
v2:
s/dev_priv/(dev_priv__)/ in body of for_each_engine_masked() [Chris Wilson]
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458757194-17783-2-git-send-email-david.s.gordon@intel.com
This version of GuC firmware fixes the engine reset issue where golden
context LRC address is treated as page index by mistake. It also fixes
the problem that scheduler stops submiting to one engine when the other
engine work queue is full.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Some trivial ones, first pass done with Coccinelle:
@@
@@
(
- I915_NUM_RINGS
+ I915_NUM_ENGINES
|
- intel_ring_flag
+ intel_engine_flag
|
- for_each_ring
+ for_each_engine
|
- i915_gem_request_get_ring
+ i915_gem_request_get_engine
|
- intel_ring_idle
+ intel_engine_idle
|
- i915_gem_reset_ring_status
+ i915_gem_reset_engine_status
|
- i915_gem_reset_ring_cleanup
+ i915_gem_reset_engine_cleanup
|
- init_ring_lists
+ init_engine_lists
)
But that didn't fully work so I cleaned it up with:
for f in *.[hc]; do sed -i -e s/I915_NUM_RINGS/I915_NUM_ENGINES/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_request_get_ring/i915_gem_request_get_engine/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_flag/intel_engine_flag/ $f; done
for f in *.[hc]; do sed -i -e s/intel_ring_idle/intel_engine_idle/ $f; done
for f in *.[hc]; do sed -i -e s/init_ring_lists/init_engine_lists/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_cleanup/i915_gem_reset_engine_cleanup/ $f; done
for f in *.[hc]; do sed -i -e s/i915_gem_reset_ring_status/i915_gem_reset_engine_status/ $f; done
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
It does not look like this code needs to wait atomically?
Higher in the call chain it calls the GEM API and I do
not see that the section is under any spin locks or such.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
During driver unloading, the guc_client created for command submission
needs to be released to avoid memory leak.
The struct_mutex needs to be held before tearing down GuC.
v1: Move i915_guc_submission_disable out of i915_guc_submission_fini and
take struct_mutex lock before release GuC client. (Dave Gordon)
v2: Add the locking for failure case in guc_fw_fetch. (Dave Gordon)
Add i915_guc_submission_fini for failure case in intel_guc_ucode_load.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452711710-4505-1-git-send-email-yu.dai@intel.com
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJWUmHZAAoJEHm+PkMAQRiGHtcH/RVRsn8re0WdRWYaTr9+Hknm
CGlRJN4LKecttgYQ/2bS1QsDbt8usDPBiiYVopqGXQxPBmjyDAqPjsa+8VzCaVc6
WA+9LDB+PcW28lD6BO+qSZCOAm7hHSZq7dtw9x658IqO+mI2mVeCybsAyunw2iWi
Kf5q90wq6tIBXuT8YH9MXGrSCQw00NclbYeYwB9CmCt9hT/koEFBdl7uFUFitB+Q
GSPTz5fXhgc5Lms85n7flZlrVKoQKmtDQe4/DvKZm+SjsATHU9ru89OxDBdS5gSG
YcEIM4zc9tMjhs3GC9t6WXf6iFOdctum8HOhUoIN/+LVfeOMRRwAhRVqtGJ//Xw=
=DCUg
-----END PGP SIGNATURE-----
Merge tag 'v4.4-rc2' into drm-intel-next-queued
Linux 4.4-rc2
Backmerge to get at
commit 1b0e3a049e
Author: Imre Deak <imre.deak@intel.com>
Date: Thu Nov 5 23:04:11 2015 +0200
drm/i915/skl: disable display side power well support for now
so that we can proplery re-eanble skl power wells in -next.
Conflicts are just adjacent lines changed, except for intel_fbdev.c
where we need to interleave the changs. Nothing nefarious.
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
DRM_ERROR an continue without any issues aren't allowed since that
causes noise in the CI system. But we absolutely want to have the
DRM_ERROR when we want to run with GuC.
For simplicity just short-circuit all the loader code when it's not
needed.
v2: Mika&Chris complained that I shouldn't hit send on patches written
before coffee kicks in.
v3: Make it compile at least ...
Cc: Alex Dai <yu.dai@intel.com>
Cc: Dave Gordon <david.s.gordon@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445591459-4327-1-git-send-email-daniel.vetter@ffwll.ch
Reviewed-by: Mika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The size / offset information of all firmware ingredients are
now caculated from header. Driver will validate the header and
rsa key size. If any component is out of boundary, driver will
reject the loading too.
v6: Clean up warnings from make docs
v5: Tidy up GuC titles in kernel/Doc
v4: Now using 'size_dw' for those defined in css_header
v3: 1) Move DOC to intel_guc_fwif.h right before css_header
definition. Add more comments.
2) Change 'size' to 'len' or 'length' to avoid confusion.
3) Add UOS_RSA_SCRATCH_MAX_COUNT according to BSpec. And
driver validate size of RSA key now.
4) Add fw component size/offset info to intel_guc_fw.
v2: Add indent into DOC to make fixed-width format rather than
change the tmpl.
v1: 1) guc_css_header is defined as __packed now
2) Add and correct GuC related topics in kernel/Doc
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Revision checks are almost always accompanied by a platform check. (The
exceptions are platform specific code.) Add helpers to check for a
platform and a revision range: IS_SKL_REVID() and IS_BXT_REVID(). In
most places this simplifies and clarifies the code. It will be obvious
that revid macros are used for the correct platform.
This should make it easier to find all the revision checks for
workarounds for each platform, and make it easier to remove them once we
drop support for early hardware revisions.
This should also make it easier to differentiate between Skylake and
Kabylake revision checks when Kabylake support is added.
v2: rebase
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1445343722-3312-3-git-send-email-jani.nikula@intel.com
Add host2guc interface to notify GuC power state changes when
enter or resume from power saving state.
v3: Move intel_guc_suspend to i915_drm_suspend for consistency.
v2: Add GuC suspend/resume to runtime suspend/resume too
v1: Change to a more flexible way when fill host to GuC scratch
data in order to remove hard coding.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Due to flip interrupts GuC stays awake always and GT does not enter
RC6. Do not route those interrupts to GuC for now. Driver won't touch
DE_GUCRMR register and leave it as what default value.
Signed-off-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Bit 16 of GuC status indicates resuming from RC6. The LAPIC_DONE
status is a reliable readiness flag only when resuming from RC6.
This fix a racing issue that allocation of doorbell fails whilst
GuC init is not finished.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Sagar Arun Kamble <sagar.a.kamble@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The firmware layout changes that now it only has css header +
uCode + RSA signature. Plus, other trivial changes to support
GuC V4.3.
Signed-off-by: Alex Dai <yu.dai@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Turn on interrupt steering to route necessary interrupts to GuC.
v6:
Rebased
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
A GuC client has its own doorbell and workqueue. It maintains the
doorbell cache line, process description object and work queue item.
A default guc_client is created for the i915 driver to use for
normal-priority in-order submission.
Note that the created client is not yet ready for use; doorbell
allocation will fail as we haven't yet linked the GuC's context
descriptor to the default contexts for each ring (see later patch).
v2:
Defer adding structure members until needed [Chris Wilson]
Rationalise type declarations [Chris Wilson]
v5:
Add GuC per-engine submission & seqno statistics.
Move wq locking to encompass both get_space() and add_item().
Take forcewake lock in host2guc_action() [Tom O'Rourke]
v6:
Fix GuC doorbell cacheline selection code (the
cacheline-within-page calculation was wrong).
Rename GuC priorities to make them closer to the names used in
the GuC firmware source, matching what the autogenerated
versions will (probably) be.
Add per-ring statistics to client.
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This adds the first of the data structures used to communicate with the
GuC (the pool of guc_context structures).
We create a GuC-specific wrapper round the GEM object allocator as all
GEM objects shared with the GuC must be pinned into GGTT space at an
address that is NOT in the range [0..WOPCM_TOP), as that range of GGTT
addresses is not accessible to the GuC (from the GuC's point of view,
it's permanently reserved for other objects such as the BootROM & SRAM).
Later, we will need to allocate additional GuC-sharable objects for the
submission client(s) and the GuC's debug log.
v2:
Remove redundant initialisation [Chris Wilson]
Defer adding struct members until needed [Chris Wilson]
Local functions should pass dev_priv rather than dev [Chris Wilson]
v5:
Invalidate GuC TLB after allocating and pinning a new object
v6:
Rebased
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This fetches the required firmware image from the filesystem,
then loads it into the GuC's memory via a dedicated DMA engine.
This patch is derived from GuC loading work originally done by
Vinit Azad and Ben Widawsky.
v2:
Various improvements per review comments by Chris Wilson
v3:
Removed 'wait' parameter to intel_guc_ucode_load() as firmware
prefetch is no longer supported in the common firmware loader,
per Daniel Vetter's request.
Firmware checker callback fn now returns errno rather than bool.
v4:
Squash uC-independent code into GuC-specifc loader [Daniel Vetter]
Don't keep the driver working (by falling back to execlist mode)
if GuC firmware loading fails [Daniel Vetter]
v5:
Clarify WOPCM-related #defines [Tom O'Rourke]
Delete obsolete code no longer required with current h/w & f/w
[Tom O'Rourke]
Move the call to intel_guc_ucode_init() later, so that it can
allocate GEM objects, and have it fetch the firmware; then
intel_guc_ucode_load() doesn't need to fetch it later.
[Daniel Vetter].
v6:
Update comment describing intel_guc_ucode_load() [Tom O'Rourke]
Issue: VIZ-4884
Signed-off-by: Alex Dai <yu.dai@intel.com>
Signed-off-by: Dave Gordon <david.s.gordon@intel.com>
Reviewed-by: Tom O'Rourke <Tom.O'Rourke@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
