Note includes a merge from i3c tree to get support needed for stm_lsm6dsx driver
support for l3c devices. Done from immutable branch.
A counter subsystem patche in here as well.
Alongside the new device support (which is always good), Chuhong's work
on using devres managed APIs has cleaned up a number of drivers.
New device support
* adis16460
- New driver based on ADIS framework which needed addition of support
for cs_change_delay. Includes device tree binding.
* cros_ec
- Support fo the veyron-minnie which uses an older interface.
* lsm6dsx
- Support for LSM6DSTR-C gyro + magnetometer sensor (new IDs mainly)
- Support for ISM330DHCX acc + gyro sensor (extensive rework needed!)
* Maxim 5432
- New driver support MAX5432-MAX5435 family of potentiometers.
* noa1305
- New driver for this ON Semiconductor Ambient light sensor.
Features and cleanups
* tree wide
- Drop error prints after platform_get_irq as already prints errors
internally if any occur.
* docs
- Document mounting matrix.
- Fix a missing newline at end of file.
* ad2s1210
- Switch to device managed APIs for all of probe and drop explicit remove.
* ad7192
- Add of_device_id array to explicity handling DT bindings.
* ad7606
- Lots of rework leading to support for software configure modes in ad7616
parts.
- Debugfs register access support.
* am2315
- Switch to device managed APIs for all of probe and drop explicit remove.
* apds9960
- Typo in module description.
* cm36651
- Convert to i2c_new_dummy_device.
- Swithc to device managed APIs for all of probe adn drop explicit remove.
* cros_ec
- Calibscale support for accel, gyro and magnetometer.
- Tidy up some error codes to return the error from the stack rather than
-EIO.
- Determine protocol version.
- Add a sign vector to the core to fix sensor rotation if necessary.
Cannot just be done with mount matrix as already in use in many devices.
- Tidy up INFO_SCALE being in both the separate and shared lists.
- Drop a lot of dplicate code from the cros-ec-accel-legacy driver
and use the core provided code instead.
- Make frequency range available to userspace.
* counter / ftm-quaddec
- Switch to device managed APIs for all of probe adn drop explicit remove.
* hdc100x
- Switch to device managed APIs for all of probe and drop explicit remove.
* hi8435
- Use gpiod_set_value_cansleep as we don't care here and there is a
board out there where it needs to sleep.
- Switch to device managed APIs for all of probe and drop explict remove.
* hp03
- Convert to i2c_new_dummy_device.
* maxim thermocouple
- Switch to device managed APIs for all of probe and drop explicit remove.
* mmc35240
- Fix typo in constant naming.
* mpu6050
- Use devm_add_action_or_reset in place of explicit error handling.
- Make text in Kconfig more explicit about which parts are supported.
* mxc4005
- Switch to device managed APIs for all of probe and drop explicit remove.
* pms7003
- Convert device tree bindings to yaml.
- Add a MAINTAINERS entry
* sc27xx
- Introduce a local struct device *dev pointer to avoid lots of deref.
- Use devm_add_action_or_reset in place of explicit error handling.
* sca3000
- Typo fix in naming.
* si1145
- Switch to device managed APIs for all of probe and drop explicit remove.
* st_sensors
- Lots of rework to enable switch to regmap.
- Regmap conversion at the end.
- Tidy up some inconsistencies in buffer setup ops.
- Tidy up an oddity by dropping get_irq_data_ready function in favour
of direct access.
- Stop allocating buffer in buffer enable in favour of just embedding
a large enough constant size buffer in the iio_priv accessed structure.
* st_lsm6dsx
- l3c device support (LSM6DSO and LSM6DSR)
- tidy up irq return logic which was strangely written.
- fix up an ABI quirk where this driver used separate scale
attributes, even though they were always shared by type.
* stk33xx
- Device tree bindings include manufacturer ID.
* stm32-adc
- Add control for supply to analog switches including DT bindings.
* stm32 timer
- Drop the quadrature mode support. Believed there were no users so
take this opportunity to drop this unwanted ABI.
* tsl2772
- Switch to device mangage APIs for all of probe and drop explicit remove.
- Use regulator_bulk_* APIs to reduce repitition.
* veml6070
- Convert to i2c_new_dummy_device.
-----BEGIN PGP SIGNATURE-----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=aez5
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First set of new device support, features and cleanups for IIO in the 5.4 cycle
Note includes a merge from i3c tree to get support needed for stm_lsm6dsx driver
support for l3c devices. Done from immutable branch.
A counter subsystem patche in here as well.
Alongside the new device support (which is always good), Chuhong's work
on using devres managed APIs has cleaned up a number of drivers.
New device support
* adis16460
- New driver based on ADIS framework which needed addition of support
for cs_change_delay. Includes device tree binding.
* cros_ec
- Support fo the veyron-minnie which uses an older interface.
* lsm6dsx
- Support for LSM6DSTR-C gyro + magnetometer sensor (new IDs mainly)
- Support for ISM330DHCX acc + gyro sensor (extensive rework needed!)
* Maxim 5432
- New driver support MAX5432-MAX5435 family of potentiometers.
* noa1305
- New driver for this ON Semiconductor Ambient light sensor.
Features and cleanups
* tree wide
- Drop error prints after platform_get_irq as already prints errors
internally if any occur.
* docs
- Document mounting matrix.
- Fix a missing newline at end of file.
* ad2s1210
- Switch to device managed APIs for all of probe and drop explicit remove.
* ad7192
- Add of_device_id array to explicity handling DT bindings.
* ad7606
- Lots of rework leading to support for software configure modes in ad7616
parts.
- Debugfs register access support.
* am2315
- Switch to device managed APIs for all of probe and drop explicit remove.
* apds9960
- Typo in module description.
* cm36651
- Convert to i2c_new_dummy_device.
- Swithc to device managed APIs for all of probe adn drop explicit remove.
* cros_ec
- Calibscale support for accel, gyro and magnetometer.
- Tidy up some error codes to return the error from the stack rather than
-EIO.
- Determine protocol version.
- Add a sign vector to the core to fix sensor rotation if necessary.
Cannot just be done with mount matrix as already in use in many devices.
- Tidy up INFO_SCALE being in both the separate and shared lists.
- Drop a lot of dplicate code from the cros-ec-accel-legacy driver
and use the core provided code instead.
- Make frequency range available to userspace.
* counter / ftm-quaddec
- Switch to device managed APIs for all of probe adn drop explicit remove.
* hdc100x
- Switch to device managed APIs for all of probe and drop explicit remove.
* hi8435
- Use gpiod_set_value_cansleep as we don't care here and there is a
board out there where it needs to sleep.
- Switch to device managed APIs for all of probe and drop explict remove.
* hp03
- Convert to i2c_new_dummy_device.
* maxim thermocouple
- Switch to device managed APIs for all of probe and drop explicit remove.
* mmc35240
- Fix typo in constant naming.
* mpu6050
- Use devm_add_action_or_reset in place of explicit error handling.
- Make text in Kconfig more explicit about which parts are supported.
* mxc4005
- Switch to device managed APIs for all of probe and drop explicit remove.
* pms7003
- Convert device tree bindings to yaml.
- Add a MAINTAINERS entry
* sc27xx
- Introduce a local struct device *dev pointer to avoid lots of deref.
- Use devm_add_action_or_reset in place of explicit error handling.
* sca3000
- Typo fix in naming.
* si1145
- Switch to device managed APIs for all of probe and drop explicit remove.
* st_sensors
- Lots of rework to enable switch to regmap.
- Regmap conversion at the end.
- Tidy up some inconsistencies in buffer setup ops.
- Tidy up an oddity by dropping get_irq_data_ready function in favour
of direct access.
- Stop allocating buffer in buffer enable in favour of just embedding
a large enough constant size buffer in the iio_priv accessed structure.
* st_lsm6dsx
- l3c device support (LSM6DSO and LSM6DSR)
- tidy up irq return logic which was strangely written.
- fix up an ABI quirk where this driver used separate scale
attributes, even though they were always shared by type.
* stk33xx
- Device tree bindings include manufacturer ID.
* stm32-adc
- Add control for supply to analog switches including DT bindings.
* stm32 timer
- Drop the quadrature mode support. Believed there were no users so
take this opportunity to drop this unwanted ABI.
* tsl2772
- Switch to device mangage APIs for all of probe and drop explicit remove.
- Use regulator_bulk_* APIs to reduce repitition.
* veml6070
- Convert to i2c_new_dummy_device.
* tag 'iio-for-5.4a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (84 commits)
iio: hi8435: Drop hi8435_remove() by using devres for remaining elements
iio: hi8435: Use gpiod_set_value_cansleep()
iio:st_sensors: remove buffer allocation at each buffer enable
iio: imu: inv_mpu6050: be more explicit on supported chips
iio: light: noa1305: Add support for NOA1305
dt-bindings: Add binding document for NOA1305
iio: remove get_irq_data_ready() function pointer and use IRQ number directly
iio: imu: st_lsm6dsx: make IIO_CHAN_INFO_SCALE shared by type
iio: tsl2772: Use regulator_bulk_() APIs
iio: tsl2772: Use devm_iio_device_register
iio: tsl2772: Use devm_add_action_or_reset for tsl2772_chip_off
iio: tsl2772: Use devm_add_action_or_reset
iio: Remove dev_err() usage after platform_get_irq()
iio: light: si1145: Use device-managed APIs
iio:pressure: preenable/postenable/predisable fixup for ST press buffer
iio:magn: preenable/postenable/predisable fixup for ST magn buffer
iio:gyro: preenable/postenable/predisable fixup for ST gyro buffer
iio:accel: preenable/postenable/predisable fixup for ST accel buffer
dt-bindings: iio: imu: st_lsm6dsx: add ism330dhcx device bindings
iio: imu: st_lsm6dsx: add support to ISM330DHCX
...
Since every chip has a different whoami, we are not supporting all
existing variant of all chips. Add an explicit supported chips
list in Kconfig description.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
in_accel_x_scale, in_accel_y_scale and in_accel_z_scale are always
the same. The scale is still defined to be in "info_mask_separate".
Userspace (iio-sensor-proxy and others) is not used to that and only
looks for "in_accel_scale" for the scaling factor to apply.
Change IIO_CHAN_INFO_SCALE from being separate in all channel to be
shared by type.
This removes in_accel_x_scale, in_accel_y_scale and in_accel_z_scale and
makes available in_accel_scale.
This is an ABI change, but hopefully in the 'no one will notice'
category. The cleanup in interface is worth the small risk that
there is a custom script out there somewhere that this will break.
Signed-off-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM ISM330DHCX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/ism330dhcx.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move IIO channel definitions in st_lsm6dsx_sensor_settings in order to
support sensors with different channels maps.
This is a preliminary patch to add support for LSM9DS1 sensor to
st_lsm6dsx driver.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Remove output register definition and inline register value since
they are used only for iio channel definition. This is a preliminary
patch to add support for LSM9DS1 sensor to st_lsm6dsx driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move fs_table in st_lsm6dsx_sensor_settings in order to support
sensors with different gain maps. This is a preliminary patch to add
support for LSM9DS1 sensor to st_lsm6dsx driver
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Move sensor odr table in st_lsm6dsx_sensor_settings in order to support
sensors with different odr maps. This is a preliminary patch to add
support for LSM9DS1 sensor to st_lsm6dsx driver
Tested-by: Martin Kepplinger <martin.kepplinger@puri.sm>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
No need for using reverse logic in the irq return,
fix this by flip things around.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
For today the st_lsm6dsx driver support LSM6DSO and LSM6DSR sensor only in
spi and i2c mode.
The LSM6DSO and LSM6DSR are also i3c capable so let's give i3c support to
them.
Signed-off-by: Vitor Soares <vitor.soares@synopsys.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16460 device is a complete inertial system that includes a triaxial
gyroscope and a triaxial accelerometer. It's more simplified design than
that of the ADIS16480, and does not offer the triaxial magnetometers &
pressure sensors. It does also have a temperature sensor (like the
ADIS16480).
Since it is part of the ADIS16XXX family, it re-uses parts of the ADIS
library.
Naturally, the register map is different and much more simplified than the
ADIS16480 subfamily, so it cannot be integrated into that driver. A major
difference is that the registers are not paged.
One thing that is particularly special about it, is that it requires a
higher delay between CS changes (i.e. when CS goes up, the spec recommends
that it be brought down after a minimum of 16 uS).
Other ADIS chips require (via spec) a minimum of 2 uS between CS changes.
The kernel's 10 uS default should be fine for those other chips; they
haven't been tested with lower CS change delays yet.
Datasheet:
https://www.analog.com/media/en/technical-documentation/data-sheets/adis16460.pdf
Signed-off-by: Dragos Bogdan <dragos.bogdan@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16460 requires a higher delay before the next transfer. Since the
SPI framework supports configuring the delay before the next transfer, this
driver will become the first user of it.
The support for this functionality in ADIS16460 requires an addition to the
ADIS lib to support the `cs_change_delay` functionality from the SPI
subsystem.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DS3TR-C 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6ds3tr-c.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
devm_add_action_or_reset() is introduced as a helper function which
internally calls devm_add_action(). If devm_add_action() fails
then it will execute the action mentioned and return the error code.
This reduce source code size (avoid writing the action twice)
and reduce the likelyhood of bugs.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver only supports 3-axis gyro and/or 3-axis accel.
For icm20602, temp data is mandatory for all configurations.
Fix all single and double axis configurations (almost never used) and more
importantly fix 3-axis gyro and 6-axis accel+gyro buffer on icm20602 when
temp data is not enabled.
Signed-off-by: Jean-Baptiste Maneyrol <jmaneyrol@invensense.com>
Fixes: 1615fe41a1 ("iio: imu: mpu6050: Fix FIFO layout for ICM20602")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
-----BEGIN PGP SIGNATURE-----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=a3vh
-----END PGP SIGNATURE-----
Merge tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO device support, features, cleanups and minor fixes for 5.3.
A few bits for the counters subsystem mixed in here as well.
There are some late breaking fixes as well, which aren't so urgent
they can't wait for the merge window.
New Device Support
* adf4371
- New driver + bindings.
- Support the adf4372 PLL. Mostly ID and bindings.
* ad8366 (note includes rework of driver needed to allow support for these).
- Support the ADL5240 variable gain amplifier (VGA).
- Support the ADA4961 digital gain amplifier (DGA).
* dps310
- New driver, in several parts from different authors for this temp
and pressure sensor.
- Includes errata workaround for a temperature reading issue.
* stk3310
- Support the stk3335, mostly ID.
Features and cleanups
* core
- drop error handling on debugfs registration.
- harden by making sure we don't overrun iio_chan_info_postfix.
* docs
- convert remaining docs to rst. At somepoint we'll fit these few
into the main IIO docs.
- improve sampling_frequency_available docs but explaining the
range form.
* ad_sigma_delta
- Drop a pointless goto.
* ad2s1210
- Drop pointless platform data null check seeing as we don't actually
use platform data anymore.
* ad7124
- Relax limitation on channel numbers to allow pseudo different channels.
- Support control of whether the input is buffered via DT.
- Use dynamic allocation for channel configuration to make it easier
to support new devices.
- YAML binding conversion.
* ad7150
- Comment tidy up.
- Consistent and simple if (ret) handling of i2c errors.
- FIELD_GET and GENMASK.
- Ternary rather than !!(condition) for readability.
- Use macros to avoid repetition of channel definitions.
* ad7606
- Add software channel config (rather that pin controlled)
- Refactor to simplify addition of new part in future.
* ad7746
- of_deivce_id table.
* ad7780
- MAINTAINERS entry
- YAML DT bindings.
* ad8366
- Stop using core mlock in favour of well scoped local lock.
- SPDX + copyright date update.
* ad9834
- of_device_id table
* adf4371
- Add support for output stage muting before lock on has occured.
* adis library
- MAINTAINERS entry to reflect that this now Alexandru's problem ;)
* adis162xx:
- Fix a slightly incorrect set of comments and print statements on
minimum supported voltage.
* adis16203
- of_device_id table.
* adis16240
- Add of_device_id table (in two parts as first patch only used it for
MODULE_DEVICE_TABLE.)
* adt7316-spi
- of_device_id table
* adxl372
- YAML DT binding conversion.
- Cleanup use of buffer callback functions (precursor to core rework).
* bh1710
- Simplify getting the i2c adapter from the client.
* dht11
- Mote to newer GPIO consumer interface.
* kxcjk-1013.c
- Add binding for sensor in display of some ultrabooks after userspace
tools updated for it not be a problem to report two similar sensors.
* imx7d
- drop unused variables.
- white space
- define instead of variable for clock frequency that is fixed.
- drop pointless error message.
* messon_saradc
- SPDX
* sps30
- MAINTAINERS entry
- YAML binding conversion.
* st_accel
- Tidy up ordering in various buffer related callbacks. This is
part of a long running effort to simplify the core code.
* stm32-dfsdm:
- Manage the resolution cleanly in triggerd modes.
- Add fast mode support which allows more flexible filter choices.
- Add a comment on the reason for a 16 bit record when technically
not 'required'.
* st_lsm6dsx
- Embed device name in the sensor_settings struct as i3c doesn't
have a convenient name field to use for this.
* xilinx-adc
- Relax constraints on supported platforms to reflect that this
can used with FPGAs on PCIe cards and hence many architectures.
* counters/ftm-quaddec
- Fix some formatting io MODULE_AUTHOR
- MAINTAINERS entry
Fixes
* tools
- fix incorrect handling of 32 bit channels.
* sca3000
- Potential endian bug that is unlikely to bite anyone (be64 host
seems unlikely for this old part).
* stm32-adc
- Add vdda-supply. On some boards it needs to be turned on to supply
the ADC. DT bindings included.
* stm32-dfsdm
- Fix output resolution to work with filter orders other than 3.
- Fix output datatype as it's signed and previously claimed not to be.
* tag 'iio-for-5.3b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio: (68 commits)
iio: iio-utils: Fix possible incorrect mask calculation
iio: frequency: adf4371: Add support for output stage mute
dt-bindings: iio: frequency: Add ADF4372 PLL documentation
iio: frequency: adf4371: Add support for ADF4372 PLL
dt-bindings: iio: adc: Add buffered input property
Convert AD7124 bindings documentation to YAML format.
iio: adc: ad7124: Shift to dynamic allocation for channel configuration
iio: adc: ad7124: Add buffered input support
iio: adc: ad7124: Remove input number limitation
MAINTAINERS: add ADIS IMU driver library entry
iio: adis162xx: fix low-power docs & reports
counter/ftm-quaddec: Add missing '>' in MODULE_AUTHOR
iio: core: no need to check return value of debugfs_create functions
docs: iio: convert to ReST
iio: adc: stm32-adc: add missing vdda-supply
dt-bindings: iio: adc: stm32: add missing vdda supply
iio: adc: stm32-dfsdm: add comment for 16 bits record
iio: adc: stm32-dfsdm: add fast mode support
iio: adc: stm32-dfsdm: manage data resolution in trigger mode
iio: adc: stm32-dfsdm: fix data type
...
Here are some small driver bugfixes for some staging/iio/counter
drivers.
Staging and IIO have been lumped together for a while, as those
subsystems cross the areas a log, and counter is used by IIO, so that's
why they are all in one pull request here.
These are small fixes for reported issues in some iio drivers, the erofs
filesystem, and a build issue for counter code.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iGwEABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQyM7w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymBUwCYn7LKiishfnvx8PpGF1lGHNmtYACgrNoAWKRZ
PUlOWXEbtD7NAPtqn3c=
=tXAQ
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging/IIO/counter fixes from Greg KH:
"Here are some small driver bugfixes for some staging/iio/counter
drivers.
Staging and IIO have been lumped together for a while, as those
subsystems cross the areas a log, and counter is used by IIO, so
that's why they are all in one pull request here.
These are small fixes for reported issues in some iio drivers, the
erofs filesystem, and a build issue for counter code.
All have been in linux-next with no reported issues"
* tag 'staging-5.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: erofs: add requirements field in superblock
counter/ftm-quaddec: Add missing dependencies in Kconfig
staging: iio: adt7316: Fix build errors when GPIOLIB is not set
iio: temperature: mlx90632 Relax the compatibility check
iio: imu: st_lsm6dsx: fix PM support for st_lsm6dsx i2c controller
staging:iio:ad7150: fix threshold mode config bit
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ad7150
- sense of bit for controlling adaptive vs fixed threshold was flipped.
* adt7316
- Fix a build issue due to wrong headers for gpio usage.
* lsm6dsx
- correctly suspend / resume i2c slaves when the host goes to sleep.
* mlx90632
- relax a compatability check to allow for newer devices.
Also one counters fix
* counter/ftm-quaddec
- missing dependencies in Kconfig.
-----BEGIN PGP SIGNATURE-----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=2i3G
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 5.2 cycle.
* ad7150
- sense of bit for controlling adaptive vs fixed threshold was flipped.
* adt7316
- Fix a build issue due to wrong headers for gpio usage.
* lsm6dsx
- correctly suspend / resume i2c slaves when the host goes to sleep.
* mlx90632
- relax a compatability check to allow for newer devices.
Also one counters fix
* counter/ftm-quaddec
- missing dependencies in Kconfig.
* tag 'iio-fixes-for-5.2b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
counter/ftm-quaddec: Add missing dependencies in Kconfig
staging: iio: adt7316: Fix build errors when GPIOLIB is not set
iio: temperature: mlx90632 Relax the compatibility check
iio: imu: st_lsm6dsx: fix PM support for st_lsm6dsx i2c controller
staging:iio:ad7150: fix threshold mode config bit
Introduce sensor name in st_lsm6dsx_sensor_settings table. This is
a preliminary patch to add I3C support to st_lsm6dsx since i3c_device_id
data structure does not contain a name field
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Based on 1 normalized pattern(s):
this file is subject to the terms and conditions of version 2 of the
gnu general public license see the file copying in the main
directory of this archive for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 55 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190530000436.108941081@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this software is licensed under the terms of the gnu general public
license version 2 as published by the free software foundation and
may be copied distributed and modified under those terms this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 285 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.642774971@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is another set of reviewed patches that adds SPDX tags to different
kernel files, based on a set of rules that are being used to parse the
comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review and
analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on the
patches are reviewers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCHLg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykxyACgql6ktH+Tv8Ho1747kKPiFca1Jq0AoK5HORXI
yB0DSTXYNjMtH41ypnsZ
=x2f8
-----END PGP SIGNATURE-----
Merge tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull yet more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later" or "GPL-2.0-only". Only the "obvious" versions of
these matches are included here, a number of "non-obvious" variants of
text have been found but those have been postponed for later review
and analysis.
There is also a patch in here to add the proper SPDX header to a bunch
of Kbuild files that we have missed in the past due to new files being
added and forgetting that Kbuild uses two different file names for
Makefiles. This issue was reported by the Kbuild maintainer.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (82 commits)
treewide: Add SPDX license identifier - Kbuild
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 225
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 224
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 223
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 222
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 221
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 220
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 218
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 217
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 216
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 215
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 214
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 213
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 211
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 210
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 209
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 207
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 206
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 203
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 201
...
Here are some Staging and IIO driver fixes to resolve some reported
problems for 5.2-rc3.
Nothing major here, just some tiny changes, full details are in the
shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXPCE/w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylLwQCdFRL6v7IHdGYQ6cAk/tjOcyYY0IEAoNRAdZU7
n/JfHbtKvS7VpYzPzRvO
=LjTj
-----END PGP SIGNATURE-----
Merge tag 'staging-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO driver fixes from Greg KH:
"Here are some Staging and IIO driver fixes to resolve some reported
problems for 5.2-rc3.
Nothing major here, just some tiny changes, full details are in the
shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'staging-5.2-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: kpc2000: Add dependency on MFD_CORE to kconfig symbol 'KPC2000'
staging: wilc1000: Fix some double unlock bugs in wilc_wlan_cleanup()
staging: vc04_services: prevent integer overflow in create_pagelist()
Staging: vc04_services: Fix a couple error codes
staging: wlan-ng: fix adapter initialization failure
staging: kpc2000: double unlock in error handling in kpc_dma_transfer()
staging: kpc2000: Fix build error without CONFIG_UIO
staging: kpc2000: fix build error on xtensa
staging: erofs: set sb->s_root to NULL when failing from __getname()
iio: adc: ti-ads8688: fix timestamp is not updated in buffer
iio: dac: ds4422/ds4424 fix chip verification
iio: imu: mpu6050: Fix FIFO layout for ICM20602
iio: adc: ads124: avoid buffer overflow
iio: adc: modify NPCM ADC read reference voltage
Based on 1 normalized pattern(s):
licensed under the gpl 2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 135 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170026.071193225@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
licensed under the gpl 2 or later
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 82 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Properly suspend/resume i2c slaves connected to st_lsm6dsx master
controller if the CPU goes in suspended state
Fixes: c91c1c844e ("imu: st_lsm6dsx: add i2c embedded controller support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ads124
- Avoid a buffer overrun when setting an array to 0.
* ads8688
- Don't use the pollfunc timestamp as it isn't set and would be wrong
anyway for a device that does sampling on demand.
* ds4422
- Fix masking on register used for chip verification. Wrong address
was being read.
* mpu6050
- Fix the fifo layout for ICM20602 to avoid underreading and hence failure
to move on to the next record in the fifo.
* NPCM ADC
- Make sure there is actually a valid regulator before reading its voltage.
-----BEGIN PGP SIGNATURE-----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=nq1b
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-5.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus:
Jonathan writes:
First set of IIO fixes for the 5.2 cycle.
* ads124
- Avoid a buffer overrun when setting an array to 0.
* ads8688
- Don't use the pollfunc timestamp as it isn't set and would be wrong
anyway for a device that does sampling on demand.
* ds4422
- Fix masking on register used for chip verification. Wrong address
was being read.
* mpu6050
- Fix the fifo layout for ICM20602 to avoid underreading and hence failure
to move on to the next record in the fifo.
* NPCM ADC
- Make sure there is actually a valid regulator before reading its voltage.
* tag 'iio-fixes-for-5.2a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio:
iio: adc: ti-ads8688: fix timestamp is not updated in buffer
iio: dac: ds4422/ds4424 fix chip verification
iio: imu: mpu6050: Fix FIFO layout for ICM20602
iio: adc: ads124: avoid buffer overflow
iio: adc: modify NPCM ADC read reference voltage
As it has been already done for other st sensors in 'commit 9049531c91
("iio: accel: st_accel: inline per-sensor data")', get rid of some
defines and just open code the values into the appropriate struct
elements since the semantic meaning is inherent in the name of the
C99-addressable fields and there is no reason to duplicate the code
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c: In function 'st_lsm6dsx_read_tagged_fifo':
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c:520:41: warning:
variable 'gyro_sensor' set but not used [-Wunused-but-set-variable]
drivers/iio/imu/st_lsm6dsx/st_lsm6dsx_buffer.c:520:28: warning:
variable 'acc_sensor' set but not used [-Wunused-but-set-variable]
They are not used since commit 14c7c6e1a8 ("iio: imu: st_lsm6dsx: add
st_lsm6dsx_push_tagged_data routine")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The MPU6050 driver has recently gained support for the
ICM20602 IMU, which is very similar to MPU6xxx. However,
the ICM20602's FIFO data specifically includes temperature
readings, which were not present on MPU6xxx parts. As a
result, the driver will under-read the ICM20602's FIFO
register, causing the same (partial) sample to be returned
for all reads, until the FIFO overflows.
Fix this by adding a table of scan elements specifically
for the ICM20602, which takes the extra temperature data
into consideration.
While we're at it, fix the temperature offset and scaling
on ICM20602, since it uses different scale/offset constants
than the rest of the MPU6xxx devices.
Signed-off-by: Steve Moskovchenko <stevemo@skydio.com>
Fixes: 22904bdff9 ("iio: imu: mpu6050: Add support for the ICM 20602 IMU")
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DSR 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsr.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Final part of the re-organization. Move the `adis16400.h` into
`adis16400.c` since it no longer needs to be shared among other files.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change does a simple 1-to-1 rename of the adis16400_core.c file. Now
that the `adis16400_buffer.c` file was removed, everything can be moved
into a single driver file.
But first, this rename.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This change has been done separately, so that it's easier to visualize the
changed logic in the adis_scan_update() function.
Most of the function in this `adis16400_update_scan_mode()` that deals with
burst-mode will be re-used in the ADIS16480, but with different parameters.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Some variants in the ADIS16400 family support burst mode. This mechanism is
implemented in the `adis16400_buffer.c` file.
Some variants in ADIS16480 are also adding burst mode, which is
functionally similar to ADIS16400, but with different parameters. To get
there, a `adis_burst` struct is added to parametrize certain bits of the
SPI communication to setup: the register that triggers burst-mode, and the
extra-data-length that needs be accounted for when building the bust-length
buffer.
The trigger handler cannot be made generic, since it's very specific to
each ADIS164XX family.
A future enhancement of this `adis_burst` mode will be the possibility to
enable/disable burst-mode. For the ADIS16400 family it's hard-coded to on
by default. But for ADIS16480 there will be a need to disable this.
When that will be implemented, both ADIS16400 & ADIS16480 will have the
burst-mode enable-able/disable-able.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The trigger handler for the ADIS16400 is very different from the generic
one in the ADIS library. Keeping it in a separate file won't make much
sense once the update_scan_mode function will be made more generic and
moved into the ADIS library.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM LSM6DSOX 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/lsm6dsox.pdf
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Inertial sensor data collection and processing can be controlled by
configuring one of the DIOx lines as an external clock input. This
option is available for all devices supported by this driver. However,
only adis1649x devices support different modes for the external clock.
Sync mode is supported by all devices. In this mode, the output data
rate is equal with the clock frequency divided by DEC_RATE + 1. This
mode of calculation is similar with the case when the internal clock is
used.
Pulse Per Second (PPS) Mode, is only supported by adis1649x devices. In
this mode, the output data rate is equal to the product of the external
clock frequency and the scale factor in the SYNC_SCALE register.
This patch uses the "clock-names" property to enable the external clock
in one of the two supported modes: "sync" or "pps". This property is
optional. If it is not specified, the internal clock is used.
This patch also offers the option to select the DIOx line to be used as
an external clock input via the custom "adi,ext-clk-pin" property. If this
field is left empty, DIO2 is assigned as default external clock input pin.
Each DIOx pin supports only one function at a time (data ready line
selection or external clock input).
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Add support to STM ASM330LHH 6-axis (acc + gyro) Mems sensor
https://www.st.com/resource/en/datasheet/asm330lhh.pdf
Tested-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
- use temporary variable in get_mount_matrix()
- remove , after { }
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Currently mount matrix is allowed in Device Tree, though there is
no technical issue to extend it to support ACPI.
Convert the function to use device_property_read_string_array() and
thus allow to read mount matrix from ACPI if available.
Example of use in _DSD method:
Name (_DSD, Package ()
{
ToUUID("daffd814-6eba-4d8c-8a91-bc9bbf4aa301"),
Package ()
{
Package () { "mount-matrix", Package() {
"1", "0", "0",
"0", "0.866", "0.5",
"0", "-0.5", "0.866",
} },
}
})
At the same time drop the "of" prefix from its name and
convert current users.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The ADIS16495 and ADIS16497 are inertial systems that include a triaxis
gyroscope and a triaxis accelerometer. The serial peripheral interface
(SPI) provide a simple interface for data collection and configuration
control. The devices are similar to ADIS16475, ADIS16480, ADIS16485 and
ADIS16488, the main differences are highlighted below:
* The temperature data scale is 0.00565 C/LSB for ADIS16475 and ADIS1648x
devices, while for ADIS1649x 0.0125 C/LSB.
* ADIS1649x devices support different gyroscope measurement ranges which
are dependent on the dash number (-1, -2, -3), see Table 24 in the
ADIS16495 datasheet. However, the ADIS16497 gyroscopes have the same
scale as ADIS16495.
* ADIS16495 devices support the acceleration maximum range of 8g, while
ADIS16497 devices go up to 40g.
* The internal clock for ADIS1649x devices is 4.25 kSPS. The sampling
frequency is calculated by applying a decimation rate which can take a
maximum value of 4250.
* ADIS1649x devices support different default filter frequencies.
Datasheets:
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/adis16495.pdf
Link: https://www.analog.com/media/en/technical-documentation/data-sheets/adis16497.pdf
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
When setting the filter frequency, the driver looks into the
adis16480_def_filter_freqs table for the best match. Pass this table to
the chip_info struct since future devices will need to use a different
table.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The adis1648x devices have an internal clock of 2.46 kSPS. The sampling
frequency is calculated by applying a decimation rate which can take the
maximum value of 2047.
Although all adis1648x devices are similar in this regard, devices that
will use this feature will be added in the future.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
All supported devices provide internal temperature measurement from -40 C
to +85 C, with +25 C representing value 0x00.
This patch treats the temperature scale in a generic way, similar to the
accelerometer and gyroscope scales. So far, there are no temperature max
scale differences between the supported devices. However, devices that
will make use of this feature will be added in the future.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The driver does not have a struct of_device_id table, but supported
devices are registered via Device Trees. This patch adds OF device ID
table.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The FNCTIO_CTRL register provides configuration control for each I/O pin
(DIO1, DIO2, DIO3 and DIO4).
This patch adds the option to configure each DIOx pin as data ready
indicator with positive or negative polarity by reading the 'interrupts'
and 'interrupt-names' properties from the devicetree. The
'interrupt-names' property is optional, if it is not specified, then the
DIO1 pin is used as default data ready signal.
Although the factory default assigns DIO2 as data ready signal, in the
versions previous this patch, DIO1 pin was used. We should leave this
configuration as is, since some devices might be expecting the interrupt
on the wrong physical pin.
Signed-off-by: Stefan Popa <stefan.popa@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
