FIELD_SIZEOF is defined as a macro to calculate the specified value. Therefore,
We prefer to use the macro rather than calculating its value.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_pull_bc_msg':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:907:6: warning:
variable 'fw_mbx' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c: In function 'qlcnic_sriov_issue_bc_post':
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_common.c:939:16: warning:
variable 'hdr_size' set but not used [-Wunused-but-set-variable]
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new qed firmware with fixes and support for new features.
Fixes:
- Fix a rare case of device crash with iWARP, iSCSI or FCoE offload.
- Fix GRE tunneled traffic when iWARP offload is enabled.
- Fix RoCE failure in ib_send_bw when using inline data.
- Fix latency optimization flow for inline WQEs.
- BigBear 100G fix
RDMA:
- Reduce task context size.
- Application page sizes above 2GB support.
- Performance improvements.
ETH:
- Tenant DCB support.
- Replace RSS indirection table update interface.
Misc:
- Debug Tools changes.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver displays an error message for each unrecognized dcbx TLV that's
received from the peer or configured on the device. It is observed that
syslog will be flooded with such messages in certain scenarios e.g.,
frequent link-flaps/lldp-transactions. Changing the severity of this
message to verbose level as it's not an error scenario/message.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_ERR error message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qlge_fix_features() is not supposed to modify hardware or
driver state, rather it is supposed to only fix requested
fetures bits. Currently qlge_fix_features() also goes for
interface down and up unnecessarily if there is not even
any change in features set.
This patch changes/fixes following -
1) Move reload of interface or device re-config from
qlge_fix_features() to qlge_set_features().
2) Reload of interface in qlge_set_features() only if
relevant feature bit (NETIF_F_HW_VLAN_CTAG_RX) is changed.
3) Get rid of qlge_fix_features() since driver is not really
required to fix any features bit.
Signed-off-by: Manish <manish.chopra@cavium.com>
Reviewed-by: Benjamin Poirier <bpoirier@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 90b73b77d0, list_head is no longer needed.
Now we just need to convert the list iteration to array
iteration for drivers.
Fixes: 90b73b77d0 ("net: sched: change action API to use array of pointers to actions")
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep sending mailbox commands to the MFW when it is not responsive ends up
with a redundant amount of timeout expiries.
This patch prints the MCP status on the first command which is not
responded, and blocks the following commands.
Since the (un)load request commands might be not responded due to other
PFs, the patch also adds the option to skip the blocking upon a failure.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFW manages an internal lock to prevent concurrent hardware
(de)initialization of different PFs.
This, together with the busy-waiting for the MFW's responses for commands,
might lead to a deadlock during concurrent load or unload of PFs.
This patch adds the option to sleep within the busy-waiting, and uses it
for the (un)load requests (which are not sent from an interrupt context) to
prevent the possible deadlock.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Successive iterations of halting and resuming the management chip (MCP)
might fail, since currently the driver doesn't wait for these operations to
actually take place.
This patch prevents the driver from moving forward before the operations
are reflected in the state register.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The MFW might be reset and re-update its shared memory.
Upon the detection of such a reset the driver rereads this memory, but it
has to wait till the data is valid.
This patch adds the missing wait for a data ready indication.
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: 5e7baf0fcb ("qed/qede: Multi CoS support.")
Signed-off-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Array msi_tgt_status is defined but never used, hence it is
redundant and can be removed.
Cleans up clang warning:
warning: 'msi_tgt_status' defined but not used [-Wunused-const-variable=]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The main motive of this patch is to lay down driver's
tc offload infrastructure in place.
With these changes tc can offload various supported flow
profiles (4 tuples, src-ip, dst-ip, l4 port) for the drop
action. Dropped flows statistic is a global counter for
all the offloaded flows for drop action and is populated
in ethtool statistics as common "gft_filter_drop".
Examples -
tc qdisc add dev p4p1 ingress
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp dst_ip 192.168.40.200 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto udp src_ip 192.168.40.100 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp src_ip 192.168.40.100 dst_ip 192.168.40.200 \
src_port 453 dst_port 876 action drop
tc filter add dev p4p1 protocol ipv4 parent ffff: flower \
skip_sw ip_proto tcp dst_port 98 action drop
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for dropping and redirecting
the flows based on destination IP in the packet.
This also moves the profile mode settings in their own
functions which can be used through tc flows in successive
patch.
For example -
ethtool -N p5p1 flow-type tcp4 dst-ip 192.168.40.100 action -1
ethtool -N p5p1 flow-type udp4 dst-ip 192.168.50.100 action 1
ethtool -N p5p1 flow-type tcp4 dst-ip 192.168.60.100 action 0x100000000
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for tc mqprio offload,
using this different traffic classes on the adapter
can be utilized based on configured priority to tc map.
For example -
tc qdisc add dev eth0 root mqprio num_tc 4 map 0 1 2 3
This will cause SKBs with priority 0,1,2,3 to transmit
over tc 0,1,2,3 hardware queues respectively.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 114811 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1410181 ("Missing break in switch")
Addresses-Coverity-ID: 1410184 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1384501 ("Missing break in switch")
Addresses-Coverity-ID: 1398869 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1410182 ("Missing break in switch")
Addresses-Coverity-ID: 1410183 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Notice that in this particular case, I replaced the code comments with
a proper "fall through" annotation, which is what GCC is expecting
to find.
Addresses-Coverity-ID: 114809 ("Missing break in switch")
Addresses-Coverity-ID: 114810 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RoCE qps use a pair of physical queues (pq) received from the Queue Manager
(QM) - an offload queue (OFLD) and a low latency queue (LLT). The QM block
creates a pq for each TC, and allows RoCE qps to ask for a pq with a
specific TC. As a result, qps with different VLAN priorities can be mapped
to different TCs, and employ features such as PFC and ETS.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Distinguish not set offload_tc from offload_tc 0 and add getters and
setters.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The API receives a priority and looks for the TC it is mapped to in the
operational DCBX configuration. The API returns QED_DCBX_DEFAULT_TC (0)
when DCBX is disabled.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes the following sparse warning:
drivers/net/ethernet/qlogic/qed/qed_cxt.c:1534:6: warning: symbol 'qed_cm_init_pf' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:233:4: warning: symbol 'qed_init_qm_get_num_tcs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:238:5: warning: symbol 'qed_init_qm_get_num_vfs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:246:5: warning: symbol 'qed_init_qm_get_num_pf_rls' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:264:5: warning: symbol 'qed_init_qm_get_num_vports' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dev.c:276:5: warning: symbol 'qed_init_qm_get_num_pqs' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:573:5: warning: symbol 'qed_mcp_nvm_wr_cmd' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_mcp.c:3012:1: warning: symbol '__qed_mcp_resc_lock' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_dcbx.c:870:6: warning: symbol 'qed_dcbx_aen' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7841:5: warning: symbol 'qed_dbg_nvm_image_length' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_debug.c:7857:5: warning: symbol 'qed_dbg_nvm_image' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:675:6: warning: symbol '_qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:690:6: warning: symbol 'qed_iov_pf_sanity_check' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_sriov.c:3982:6: warning: symbol 'qed_iov_pf_get_pending_events' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_vf.c:172:5: warning: symbol '_qed_vf_pf_release' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:137:5: warning: symbol 'qed_rdma_get_sb_id' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_rdma.c:709:5: warning: symbol 'qed_rdma_stop' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_ll2.c:161:6: warning: symbol 'qed_ll2b_complete_rx_packet' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_roce.c:160:6: warning: symbol 'qed_roce_free_cid_pair' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:380:12: warning: symbol 'iwarp_state_names' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:946:1: warning: symbol 'qed_iwarp_parse_private_data' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:971:1: warning: symbol 'qed_iwarp_mpa_reply_arrived' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2504:1: warning: symbol 'qed_iwarp_ll2_slowpath' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2806:6: warning: symbol 'qed_iwarp_qp_in_error' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2827:6: warning: symbol 'qed_iwarp_exception_received' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:2958:1: warning: symbol 'qed_iwarp_connect_complete' was not declared. Should it be static?
drivers/net/ethernet/qlogic/qed/qed_iscsi.c:876:6: warning: symbol 'qed_iscsi_free_connection' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Denis Bolotin <Denis.Bolotin@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no in-tree callers of qed_get_cm_pq_idx_rl since it be there,
so it can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are no in-tree callers of qed_set_gft_event_id_cm_hdr.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
FW hsi contains 256 approximation buckets which are split in ramrod into
eight u32 values, but driver is using eight 'unsigned long' variables.
This patch fixes the mcast logic by making the API utilize u32.
Fixes: 83aeb933 ("qed*: Trivial modifications")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a possible race where driver can read link status in mid-transition
and see that virtual-link is up yet speed is 0. Since in this
mid-transition we're guaranteed to see a mailbox from MFW soon, we can
afford to treat this as link down.
Fixes: cc875c2e ("qed: Add link support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently, MFW publishes EEE capabilities even for Fiber-boards that don't
support them, and later since qed internally sets adv_caps it would cause
link-flap avoidance (LFA) to fail when driver would initiate the link.
This in turn delays the link, causing traffic to fail.
Driver has been modified to not to ask MFW for any EEE config if EEE isn't
to be enabled.
Fixes: 645874e5 ("qed: Add support for Energy efficient ethernet.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements the ethtool callbacks for querying sfp/eeprom module.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds qed APIs for reading the PHY module.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We accidentally left out the error handling for kstrtoul().
Fixes: a520030e32 ("qlcnic: Implement flash sysfs callback for 83xx adapter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
prog_attached of struct netdev_bpf should have been superseded
by simply setting prog_id long time ago, but we kept it around
to allow offloading drivers to communicate attachment mode (drv
vs hw). Subsequently drivers were also allowed to report back
attachment flags (prog_flags), and since nowadays only programs
attached will XDP_FLAGS_HW_MODE can get offloaded, we can tell
the attachment mode from the flags driver reports. Remove
prog_attached member.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Quentin Monnet <quentin.monnet@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Trivial fix to spelling mistake in qed_probe message.
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If format_idx == s_mcp_trace_meta.formats_num then we read one element
beyond the end of the s_mcp_trace_meta.formats[] array.
Fixes: 50bc60cb15 ("qed*: Utilize FW 8.33.11.0")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Variables consumer, cmd_desc, end_cnt and no_of_desc are being assigned
but are never used hence they are redundant and can be removed.
Cleans up clang warnings:
warning: variable 'consumer' set but not used [-Wunused-but-set-variable]
warning: variable 'cmd_desc' set but not used [-Wunused-but-set-variable]
warning: variable 'end_cnt' set but not used [-Wunused-but-set-variable]
warning: variable 'no_of_desc' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration information read at driver load can become stale after it is
updated. Mark information as not valid and re-populate when this happens.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pointer 'name' is being assigned but is never used hence it is
redundant and can be removed.
Cleans up clang warning:
warning: variable 'name' set but not used [-Wunused-but-set-variable]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simple overlapping changes in stmmac driver.
Adjust skb_gro_flush_final_remcsum function signature to make GRO list
changes in net-next, as per Stephen Rothwell's example merge
resolution.
Signed-off-by: David S. Miller <davem@davemloft.net>
When ptp clock is not available for a PF (e.g., higher PFs in NPAR mode),
get-tsinfo() callback should return the software timestamp capabilities
instead of returning the error.
Fixes: 4c55215c ("qede: Add driver support for PTP")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the correct size value while copying chassis/port id values.
Fixes: 6ad8c632e ("qed: Add support for query/config dcbx.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, driver sets the eswitch mode incorrectly as VEB (virtual
Ethernet bridging).
Need to set VEB eswitch mode only when sriov is enabled, and it should be
to set NONE by default. The patch incorporates this change.
Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory size is limited in the kdump kernel environment. Allocation of more
msix-vectors (or queues) consumes few tens of MBs of memory, which might
lead to the kdump kernel failure.
This patch adds changes to limit the number of MSI-X vectors in kdump
kernel to minimum required value (i.e., 2 per engine).
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
random_ether_addr is a #define for eth_random_addr which is
generally preferred in kernel code by ~3:1
Convert the uses of random_ether_addr to enable removing the #define
Miscellanea:
o Convert &vfmac[0] to equivalent vfmac and avoid unnecessary line wrap
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Do not advertise DCBX_LLD_MANAGED capability i.e., do not allow
external agent to manage the dcbx/lldp negotiation. MFW acts as lldp agent
for qed* devices, and no other lldp agent is allowed to coexist with mfw.
Also updated a debug print, to not to display the redundant info.
Fixes: a1d8d8a51 ("qed: Add dcbnl support.")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid calling a SIMD fastpath handler if it is NULL. The check is needed
to handle an unlikely scenario where unsolicited interrupt is destined to
a PF in INTa mode.
Fixes: fe56b9e6a ("qed: Add module with basic common support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Memory for packet buffers need to be freed in the error paths as there is
no consumer (e.g., upper layer) for such packets and that memory will never
get freed.
The issue was uncovered when port was attacked with flood of isatap
packets, these are multicast packets hence were directed at all the PFs.
For foce PF, this meant they were routed to the ll2 module which in turn
drops such packets.
Fixes: 0a7fb11c ("qed: Add Light L2 support")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This FW contains several fixes and features.
RDMA
- Several modifications and fixes for Memory Windows
- drop vlan and tcp timestamp from mss calculation in driver for
this FW
- Fix SQ completion flow when local ack timeout is infinite
- Modifications in t10dif support
ETH
- Fix aRFS for tunneled traffic without inner IP.
- Fix chip configuration which may fail under heavy traffic conditions.
- Support receiving any-VNI in VXLAN and GENEVE RX classification.
iSCSI / FcoE
- Fix iSCSI recovery flow
- Drop vlan and tcp timestamp from mss calc for fw 8.37.2.0
Misc
- Several registers (split registers) won't read correctly with
ethtool -d
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use dma_zalloc_coherent instead of dma_alloc_coherent
followed by memset 0.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for configuring SRQ and provides the necessary
APIs for rdma upper layer driver (qedr) to enable the SRQ feature.
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Yuval Bason <yuval.bason@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorrect shared memory address is used while deriving the values
for tc and pri_type. Use shmem address corresponding to 'oem_cfg_func'
where the management firmare saves tc/pri_type values.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The structure shared between driver and management firmware (MFW)
differ in sizes. The additional field defined by the MFW is not
relevant to the current driver. Add a dummy field to the structure.
Fixes: cac6f691 ("qed: Add support for Unified Fabric Port")
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes for capturing the link change count in
ethtool statistics display.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove and coalesce formats when there is an unnecessary
character after a logging newline. These extra characters
cause logging defects.
Miscellanea:
o Coalesce formats
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch, User can configure for the supported
flows to be dropped. Added a stat "gft_filter_drop"
as well to be populated in ethtool for the dropped flows.
For example -
ethtool -N p5p1 flow-type udp4 dst-port 8000 action -1
ethtool -N p5p1 flow-type tcp4 scr-ip 192.168.8.1 action -1
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the supported classification modes [4 tuples based,
udp port based, src-ip based], flows can be classified
to the VFs as well. With this patch, flows can be re-directed
to the requested VF provided in "action" field of command.
Please note that driver doesn't really care about the queue bits
in "action" field for the VFs. Since queue will be still chosen
by FW using RSS hash. [I.e., the classification would be done
according to vport-only]
For examples -
ethtool -N p5p1 flow-type udp4 dst-port 8000 action 0x100000000
ethtool -N p5p1 flow-type tcp4 src-ip 192.16.6.10 action 0x200000000
ethtool -U p5p1 flow-type tcp4 src-ip 192.168.40.100 dst-ip \
192.168.40.200 src-port 6660 dst-port 5550 \
action 0x100000000
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, driver supports flow classification to PF
receive queues based on TCP/UDP 4 tuples [src_ip, dst_ip,
src_port, dst_port] only.
This patch enables to configure different flow profiles
[For example - only UDP dest port or src_ip based] on the
adapter so that classification can be done according to
just those fields as well. Although, at a time just one
type of flow configuration is supported due to limited
number of flow profiles available on the device.
For example -
ethtool -N enp7s0f0 flow-type udp4 dst-port 45762 action 2
ethtool -N enp7s0f0 flow-type tcp4 src-ip 192.16.4.10 action 1
ethtool -N enp7s0f0 flow-type udp6 dst-port 45762 action 3
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Validate and prevent some of the configurations for
unsupported [by firmware] inputs [for example - mac ext,
vlans, masks/prefix, tos/tclass] via ethtool -N/-U.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch simplifies the ethtool rx flow configuration
[via ethtool -U/-N] flow code base by dividing it logically
into various APIs based on given protocols. It also separates
various validations and calculations done along the flow
in their own APIs.
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds callbacks for providing the ethernet protocol driver TLVs.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MFW requests the TLVs in interrupt context. Extracting of the required
data from upper layers and populating of the TLVs require process context.
The patch adds work-queues for processing the tlv requests. It also adds
the implementation for requesting the tlv values from appropriate protocol
driver.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds driver support for processing TLV requests/repsonses
from the mfw and upper driver layers respectively. The implementation
reads the requested TLVs from the shared memory, requests the values
from upper layer drivers, populates this info (TLVs) shared memory and
notifies MFW about the TLV values.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds required management firmware (MFW) interfaces such as
mailbox commands, TLV types etc.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ILT entry requires 12 bit right shifted physical address.
Existing mask for ILT entry of physical address i.e.
ILT_ENTRY_PHY_ADDR_MASK is not sufficient to handle 64bit
address because upper 8 bits of 64 bit address were getting
masked which resulted in completer abort error on
PCIe bus due to invalid address.
Fix that mask to handle 64bit physical address.
Fixes: fe56b9e6a8 ("qed: Add module with basic common support")
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
S390 bpf_jit.S is removed in net-next and had changes in 'net',
since that code isn't used any more take the removal.
TLS data structures split the TX and RX components in 'net-next',
put the new struct members from the bug fix in 'net' into the RX
part.
The 'net-next' tree had some reworking of how the ERSPAN code works in
the GRE tunneling code, overlapping with a one-line headroom
calculation fix in 'net'.
Overlapping changes in __sock_map_ctx_update_elem(), keep the bits
that read the prog members via READ_ONCE() into local variables
before using them.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes use of build_skb() throughout in driver's receieve
data path [HW gro flow and non HW gro flow]. With this, driver can
build skb directly from the page segments which are already mapped
to the hardware instead of allocating new SKB via netdev_alloc_skb()
and memcpy the data which is quite costly.
This really improves performance (keeping same or slight gain in rx
throughput) in terms of CPU utilization which is significantly reduced
[almost half] in non HW gro flow where for every incoming MTU sized
packet driver had to allocate skb, memcpy headers etc. Additionally
in that flow, it also gets rid of bunch of additional overheads
[eth_get_headlen() etc.] to split headers and data in the skb.
Tested with:
system: 2 sockets, 4 cores per socket, hyperthreading, 2x4x2=16 cores
iperf [server]: iperf -s
iperf [client]: iperf -c <server_ip> -t 500 -i 10 -P 32
HW GRO off – w/o build_skb(), throughput: 36.8 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.59 0.00 32.93 0.00 0.00 43.07 0.00 0.00 23.42
HW GRO off - with build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.70 0.00 31.70 0.00 0.00 25.68 0.00 0.00 41.92
HW GRO on - w/o build_skb(), throughput: 36.9 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.86 0.00 24.14 0.00 0.00 6.59 0.00 0.00 68.41
HW GRO on - with build_skb(), throughput: 37.5 Gbits/sec
Average: CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle
Average: all 0.87 0.00 23.75 0.00 0.00 6.19 0.00 0.00 69.19
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Manish Chopra <manish.chopra@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stress on qedi/qedr load unload lead to list_del corruption.
This is due to ll2 connection terminate freeing resources without
verifying that no more ll2 processing will occur.
This patch unregisters the ll2 status block before terminating
the connection to assure this race does not occur.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ll2 flows of flushing the txq/rxq need to be synchronized with the
regular fp processing. Caused list corruption during load/unload stress
tests.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should free all pending isles once it gets a FLUSH cqe from FW.
Part of iSCSI out of order flow.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Stress on qedi/qedr load unload lead to list_del corruption.
This is due to ll2 connection terminate freeing resources without
verifying that no more ll2 processing will occur.
This patch unregisters the ll2 status block before terminating
the connection to assure this race does not occur.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ll2 flows of flushing the txq/rxq need to be synchronized with the
regular fp processing. Caused list corruption during load/unload stress
tests.
Fixes: 0a7fb11c23 ("qed: Add Light L2 support")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver should free all pending isles once it gets a FLUSH cqe from FW.
Part of iSCSI out of order flow.
Fixes: 1d6cff4fca ("qed: Add iSCSI out of order packet handling")
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rebooting while qedr is loaded with a VLAN interface present
results in unregister_netdevice waiting for the usage count
to become free.
The fix is that rdma devices should be removed before unregistering
the netdevice, to assure all references to ndev are decreased.
Fixes: cee9fbd8e2 ("qede: Add qedr framework")
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: Michal Kalderon <michal.kalderon@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bpf syscall and selftests conflicts were trivial
overlapping changes.
The r8169 change involved moving the added mdelay from 'net' into a
different function.
A TLS close bug fix overlapped with the splitting of the TLS state
into separate TX and RX parts. I just expanded the tests in the bug
fix from "ctx->conf == X" into "ctx->tx_conf == X && ctx->rx_conf
== X".
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_VERBOSE message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A previous commit 4609adc271 ("qede: Fix qedr link update")
added a flow that could allocate rdma event objects from an
interrupt path (link notification). Therefore the kzalloc call
should be done with GFP_ATOMIC.
fixes: 4609adc271 ("qede: Fix qedr link update")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If qede driver was loaded on a device configured for iWARP
the l2 mutex wouldn't be allocated, and some l2 related
resources wouldn't be freed.
fixes: c851a9dc43 ("qed: Introduce iWARP personality")
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Sudarsana Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds driver changes for supporting the Unified Fabric Port
(UFP). This is a new paritioning mode wherein MFW provides the set of
parameters to be used by the device such as traffic class, outer-vlan
tag value, priority type etc. Drivers receives this info via notifications
from mfw and configures the hardware accordingly.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch adds support for new Multi function mode wherein the traffic
classification is done based on the 802.1ad tagging and the outer vlan tag
provided by the management firmware.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The data member 'is_mf_default' is not used by the qed/qede drivers,
removing the same.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
`mf_mode' field indicates the multi-partitioning mode the device is
configured to. This method doesn't scale very well, adding a new MF mode
requires going over all the existing conditions, and deciding whether those
are needed for the new mode or not.
The patch defines a set of bit-fields for modes which are derived according
to the mode info shared by the MFW and all the configuration would be made
according to those. To add a new mode, there would be a single place where
we'll need to go and choose which bits apply and which don't.
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_NOTICE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial fix to spelling mistake in DP_INFO message text
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The strscpy() was a recent fix (net: qed: use correct strncpy() size) to
prevent passing the length of the source buffer to strncpy() and guarantee
null termination.
It misses the goal of overwriting only the first 3 characters in
"???_BIG_RAM" and "???_RAM" while keeping the rest of the string.
Use strncpy() with the length of 3, without null termination.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Configuration information is added to the debug data collection, in
addition to register dump.
Added qed_dbg_nvm_image() that receives an image type, allocates a
buffer and reads the image. The images are saved in the buffers and the
dump size is updated.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since nvm images attributes are cached during driver load, acquiring ptt
is not needed when calling qed_mcp_get_nvm_image().
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There may be a need for VF driver to request PF to explicitly update its
bulletin with a MAC address.
e.g. When user assigns a MAC address to VF while VF is still down,
and PF's bulletin board contains different MAC address, in this case,
when VF's interface is brought up, it gets loaded with MAC address from
bulletin board which is not desirable.
To handle this corner case, we need a new TLV to request PF to update
its bulletin board with suggested MAC.
This request will be honored only for trusted VFs.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per existing behavior, when PF sets a MAC address for a VF
(also called as forced MAC), VF is not allowed to change its
MAC address afterwards.
This puts the limitation on few use cases such as bonding of VFs,
where bonding driver asks VF to change its MAC address.
This patch uses a VF trust mode to allow VF to change its MAC address
in spite PF has set a forced MAC for that VF.
Signed-off-by: Shahed Shaikh <shahed.shaikh@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
kfifo: fix inaccurate comment
tools/thermal: tmon: fix for segfault
net: Spelling s/stucture/structure/
edd: don't spam log if no EDD information is present
Documentation: Fix early-microcode.txt references after file rename
tracing: Block comments should align the * on each line
treewide: Fix typos in printk
GenWQE: Fix a typo in two comments
treewide: Align function definition open/close braces
