Original code would inadvertanly place I/Os on the default
request-queue. Also, correctly pass in the proper MSI-X vector
during response-queue initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
ROMs in recent ISPs have MSI-X support, so it's no longer
necessary for the driver to fallback to interrupt polling during
ISP re-initialization.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Software should not touch this region of flash, as the firmware
will be the only writer and consumer of the region.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Scan outstanding commands only in the queue where it is submitted
2. Update queue registers directly in the fast path
3. Queue specific BAR is remapped only for multiq capable adapters
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made.
1. qla_hw_data structure holds an array for request queue pointers,
and an array for response queue pointers.
2. The base request and response queues are created by default.
3. Additional request and response queues are created at the time of vport
creation. If queue resources are exhausted during vport creation, newly
created vports use the default queue.
4. Requests are sent to the request queue that the vport was assigned
in the beginning.
5. Responses are completed on the response queue with which the request queue
is associated with.
[fixup memcpy argument reversal spotted by davej@redhat.com]
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The following patch changes the handling of bus reset when issued from a
vport. In the bus reset code, an extra check is made to make sure that the lip
reset is not done before resetting the targets if the bus reset came from a
vport.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/qla2xxx/qla_os.c: In function 'qla2x00_probe_one':
drivers/scsi/qla2xxx/qla_os.c:1582: warning: 'mem_only' is used uninitialized in this function
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Following changes have been made:
1. Outstanding commands are based on a request queue, scsi_qla_host
does not maintain it anymore.
2. start_scsi is accessed via isp_ops struct instead of direct
invocation.
3. Interrupt registrations are done using response queue instead of
device id.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Mike Reed noted
(https://bugzilla.novell.com/show_bug.cgi?id=421330) that the
driver was incorrectly returning a SUCCESS status if the driver's
request to the firmware to abort a command failed. By doing so,
the mid-layer believed, incorrectly, that the command has
completed and has been returned (ultimately clearing
scsi_cmnd.request_buffer) yet the driver still has the command.
What should correctly happen is a mid-layer escalation
(device-reset, etc.) of recovery during which the driver will
eventually return the outstanding commands to the mid-layer.
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Remove some open coded (and buggy) versions of pci_find_ext_capability
in favor of the real routine in the PCI core.
Tested-by: Tomasz Czernecki <czernecki@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
If the fcport is not online then we do not want to block IO to all ports on
the host. We just want to stop IO on port not online, so we should be using
the SCSI_MLQUEUE_TARGET_BUSY return value.
For the case where we race with the rport memset initialization
we do not want the queuecommand to be called again so we can just use
SCSI_MLQUEUE_TARGET_BUSY for this.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
To instatiate pre-configured vport entities defined within an
HBA's flash memory.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The Flash Layout Table (FLT) present on many recent HBAs encodes
flash usage information, organizes data stored into separate
regions and presents the information uniformly to the driver.
Use this information rather than using specific hard-coded values
based on ISP type.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Josip Rodin noted
(http://article.gmane.org/gmane.linux.ports.sparc/10152) the
driver oopsing during registration of an rport to the
FC-transport layer with a backtrace indicating a dereferencing of
an shost->shost_data equal to NULL. David Miller identified a
small window in driver logic where this could happen:
> Look at how the driver registers the IRQ handler before the host has
> been registered with the SCSI layer.
>
> That leads to a window of time where the shost hasn't been setup
> fully, yet ISRs can come in and trigger DPC thread events, such as
> loop resyncs, which expect the transport area to be setup.
>
> But it won't be setup, because scsi_add_host() hasn't finished yet.
>
> Note that in Josip's crash log, we don't even see the
>
> qla_printk(KERN_INFO, ha, "\n"
> " QLogic Fibre Channel HBA Driver: %s\n"
> " QLogic %s - %s\n"
> " ISP%04X: %s @ %s hdma%c, host#=%ld, fw=%s\n",
> ...
>
> message yet.
>
> Which means that the crash occurs between qla2x00_request_irqs()
> and printing that message.
Close this window by enabling RISC interrupts after the host has
been registered with the SCSI midlayer.
Reported-by: Josip Rodin <joy@entuzijast.net>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
During internal testing, we've seen issues (hangs) with the
'deferred' vport tear-down-processing typically accompanied with
the fc_remove_host() call. This is due to the current
implementation's back-end vport handling being performed by the
physical-HA's DPC thread where premature shutdown could lead to
latent vport requests without a processor.
This should also address a problem reported by Gal Rosen
(http://marc.info/?l=linux-scsi&m=121731664417358&w=2) where the
driver would attempt to awaken a previously torn-down DPC thread
from interrupt context by implicitly calling wake_up_process()
rather than the driver's qla2xxx_wake_dpc() helper. Rather, than
reshuffle the remove_one() device-removal code, during unload,
depend on the driver's timer to wake-up the DPC process, by
limiting wake-ups based on an 'unloading' flag.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The executing-HA of an SRB can be referenced from the sp->fcport.
Use this correct value while processing status-continuation data
and abort processing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code inadvertently cleared an SRB's 'flags' while
aborting; causing a follow-on scsi_dma_unmap() to be potentially
missed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Minor fixes addressing:
- rport managements during vport deletion.
- acquire proper physical-ha during qla24xx_abort_command() and
qla24xx_queuecommand()
- do not needlessly acquire the pha for non-NPIV capable ISPs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/scsi/qla2xxx/qla_os.c: In function 'qla2x00_post_work':
drivers/scsi/qla2xxx/qla_os.c:2158: warning: 'flags' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There were several issues here, one, during RSCN handling if a
follow-on RSCN occurred (within interrupt context) the DPC thread
could inadvertantly leave the fcport in a stale lost state.
Secondly, scheduled rport removal is handled exclusively by the
'parent' DPC thread, so wake up the proper thread. Finally,
process vport loop-resync's only when the vport has in an
"active" state (ID acquired).
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
All fcport->state management should be done within
qla2x00_mark_device_lost(), the assignment of state within
qla2x00_mark_vp_devices_dead() caused associated rports to not be
removed.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
iIDMA support requires the driver issue several additional
fabric-managegment (FM) commands per port discovered during SNS
scanning -- GFPN (Get Fabric Port Name) and GPSC (Get Port Speed
Capabilities). It has been found during testing that some
switches do not respond as *well* as expected to these commands
(silence -- no ACC nor BS_RJT). So, to handle such conditions,
allow the user the ability to indirectly disable the FM commands
by disabling iIDMA with the ql2xiidmaenable module-parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Removed repeated or unnecessary operations during vport
creation/deletion.
Signed-off-by: Shyam Sundar <shyam.sundar@qlogic.com>
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As there's no point in adding a fixed-fudge value (originally 5
seconds), honor the user settings only. We also remove the
driver's dead-callback get_rport_dev_loss_tmo function
(qla2x00_get_rport_loss_tmo()).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Initialize all proper structure members in order to support
work-list vport processing. This code also properly acquires the
correct (physical hardware_lock) lock during work submission.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The semaphore vport_sem is used as a mutex. Convert it to the
mutex API.
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Commit 63a8651f25 ([SCSI] qla2xxx:
Correct infinite-login-retry issue.) introduced a small
regression where a successful relogin would result in an fcport's
loop_id to be incorrectly reset to FC_NO_LOOP_ID. Only clear-out
loopid, if retries have been 'truly' exhausted.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Stable Tree <stable@kernel.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch makes the following needlessly global functions static:
- qla2x00_alloc_work()
- qla2x00_post_work()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Original code would (incorrectly) only re-register after a
loop-down condition. Also, FDMI registration should be enabled
by default.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As there is no actual cable connection on vports, made change so
that the driver checks DFLG_NO_CABLE against ha->device_flags
only for physical port.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Ravi Anand <ravi.anand@qlogic.com>
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Now that infrastructure is present within the midlayer and there
is a clear distinction between what is expected from a device and
target reset, convert the current device-reset codes to a
target-reset, and add codes to perform a proper device-reset (LUN
reset).
In the process of adding reset support, collapse and consolidate
large sections of mailbox-command (TMF issuance) codes,
generalize the two 'wait-for-commands-to-complete' functions, and
add a generic-reset routine for use by midlayer reset functions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Strip unused (DEBUG-ONLY) enabled functions, inlines, useless
wrappers, and unused DPC flags from the code. Another step in
the migration towards a cleaner (less-crusty) driver.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Recent ISPs have a region within FLASH which acts as a repository
for the logging of serious hardware and software failures.
Currently, the region is large enough to support up to 255
entries.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Supported events include LIP, LIP reset, RSCN, link up, and link
down.
To support AEN (and additional forthcoming features), we also
introduce a simple deferred-work construct to manage events which
require a non-atomic sleeping-capable context. This work-list is
processed as part of the driver's standard DPC routine.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
While running IO simultaneously through physical port and virtual
port, if user changes Data Rate (from scli utility), IO through
virtual port fails. It failed because the vport had not received
the ISP_ABORT_NEEDED notification.
Signed-Off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
There's no functional change involved with this update, instead
it simply migrates the "set cleared interrupt state" codes to a
more approprate method, qla2x00_request_irqs(), and cleans-up the
driver's probe() logic.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Collapse duplicate codes called during probe() and RISC-reset
into qla2x00_setup_chip().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
- Drop loop-till-allocated structure of code within
qla2x00_mem_alloc().
- Properly unwind deallcations of memory during failures.
- Drop qla2x00_allocate_sp_pool() and qla2x00_free_sp_pool()
functions as their implementations can easily be collapsed into
the callers.
- Defer DMA pool allocation of SFP data until requested.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Refactor SRB-failure completion codes in the process. Also,
signal the DPC routine to complete sooner as backend processing
at shutdown-time is superflous.
[jejb: resolve conflicts with pci_enable_device_bars removal]
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.
The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.
I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With the sg table code, every SCSI driver is now either chain capable
or broken (or has sg_tablesize set so chaining is never activated), so
there's no need to have a check in the host template.
Also tidy up the code by moving the scatterlist size defines into the
SCSI includes and permit the last entry of the scatterlist pools not
to be a power of two.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
FCE support enables the firmware to record FC extended link
services and basic link services frames which have been
transmitted and received by the ISP. This allows for a limited
view of the FC traffic through the ISP without using a FC
analyzer. This can be useful in situations where a physical
connection to the FC bus is not possible.
The driver exports this information in two ways -- first, via a
debugfs node exported for all supported ISPs under:
<debugfs_mount_point>/qla2xxx/qla2xxx_<host_no>/fce
where a read of the 'fce' file will provide a snapshot of the
firmware's FCE buffer; and finally, the FCE buffer will be
extracted during a firmware-dump scenario.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
In preparation for FCE (Fibre Channel Event) tracing support.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Instead of abusing the semaphore interfaces for mailbox command
completions.
Additional cleanups and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
As the driver depends on the DPC routine to handle bottom-half
loop resynchronization in order to recover from the issue-lip
request. The issue_lip call is sleeping context capable, so just
issue the reset function there.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
The driver stores the contents of PCI resources into unsigned
long's before ioremapping. This breaks on 32-bit platforms which
support 64-bit MMIO resources.
Correct code by removing the temporary variables used during MMIO
PIO mapping and using resource_size_t where applicable. Also
correct a small typo in a printk() where the wrong region number
was displayed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
WARNING: vmlinux.o(.text+0x2a4462): Section mismatch: reference to .exit.text:qla2x00_remove_one (between 'qla2xxx_pci_error_detected' and 'qla2x00_stop_timer')
qla2x00_remove_one() mustn't be __devexit since it's called from
qla2xxx_pci_error_detected().
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent ISPs need only the single MMIO BAR to manipulate HW
registers. Unfortunately, ISP21xx, ISP22xx, ISP23xx, and ISP63xx
type cards still require the I/O mapped region to manipulate the
FLASH via the two HW flash-registers (flash_address and
flash_data).
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This option is true if a low-level driver can support sg
chaining. This will be removed eventually when all the drivers are
converted to support sg chaining. q->max_phys_segments is set to
SCSI_MAX_SG_SEGMENTS if false.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Drop usage of legacy to_qla_host() macro.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Where the DPC logic would get jammed into continuously
reloging-into a port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Newer ISPs support a mechanism to read and write flash-memory via
the firmware LOAD/DUMP memory mailbox command routines. When
supported, utilizing these mechanisms significantly reduces
overall access times.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- this patch will fix a panic caused by omitted memory allocation for the nvram.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Large code-reuse from ISP24xx, consolidate RISC memory
extraction routines during firmware-dump.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In preparation for new ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Slab destructors were no longer supported after Christoph's
c59def9f22 change. They've been
BUGs for both slab and slub, and slob never supported them
either.
This rips out support for the dtor pointer from kmem_cache_create()
completely and fixes up every single callsite in the kernel (there were
about 224, not including the slab allocator definitions themselves,
or the documentation references).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (166 commits)
[SCSI] ibmvscsi: convert to use the data buffer accessors
[SCSI] dc395x: convert to use the data buffer accessors
[SCSI] ncr53c8xx: convert to use the data buffer accessors
[SCSI] sym53c8xx: convert to use the data buffer accessors
[SCSI] ppa: coding police and printk levels
[SCSI] aic7xxx_old: remove redundant GFP_ATOMIC from kmalloc
[SCSI] i2o: remove redundant GFP_ATOMIC from kmalloc from device.c
[SCSI] remove the dead CYBERSTORMIII_SCSI option
[SCSI] don't build scsi_dma_{map,unmap} for !HAS_DMA
[SCSI] Clean up scsi_add_lun a bit
[SCSI] 53c700: Remove printk, which triggers because of low scsi clock on SNI RMs
[SCSI] sni_53c710: Cleanup
[SCSI] qla4xxx: Fix underrun/overrun conditions
[SCSI] megaraid_mbox: use mutex instead of semaphore
[SCSI] aacraid: add 51245, 51645 and 52245 adapters to documentation.
[SCSI] qla2xxx: update version to 8.02.00-k1.
[SCSI] qla2xxx: add support for NPIV
[SCSI] stex: use resid for xfer len information
[SCSI] Add Brownie 1200U3P to blacklist
[SCSI] scsi.c: convert to use the data buffer accessors
...
Following patch adds support for NPIV (N-Port ID Virtualization) to the
qla2xxx.
- supported within switched-fabric topologies only.
- supports up to 63 virtual ports on each physical port.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- remove the unnecessary map_single path.
- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iterations is unsigned, so it is impossible to get out of the loop
and return -ETIMEDOUT.
Signed-off-by: Bill Nottingham <notting@redhat.com>
Acked-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Hardcoding the qlport_down_retry module-parameter
effectively disallowed any user-defined NVRAM setting to go
into effect.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove a stale check against ha->device_flags
(DFLG_NO_CABLE) as topology scanning is performed within the
DPC-thread context.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
On the path qla2x00_probe_one() -> probe_failed -> qla2x00_free_device(),
pci_disable_device() is executed twice, once in qla2x00_free_device()
and once in qla2x00_probe_one().
This patch removes the unnecessary call.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The module parameter, ql2xextended_error_logging, can now be
set dynamically by writing to the following sysfs entry:
/sys/module/qla2xxx/parameters/ql2xextended_error_logging
This alleviates the need for the driver to be unloaded and
reloaded in order to enable logging.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since, mailbox commands are executed in a synchronous
manner, there is no need to have a separate spinlock
primitive to protect data/register access shared by callers.
Signed-off-by: Seokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This includes BIOS, EFI, FCODE and firmware versions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code would incorrectly use non-24xx code-paths.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify intialization semantics:
- perform basic hardware configuration only (as usual)
- allocate resources
- load and execute firmware
- defer link (transport) negotiations to the DPC thread
- again the code in qla2x00_initialize_adapter() to stall probe()
completion was needed for legacy-style scanning.
- DPC thread stalls until probe() complete.
- before probe() completes, set DPC flags to perform loop-resync logic
(similar to what's done during cable-insertion/removal).
Benefits: user does not have to wait 20+ seconds in case the FC cable
is unplugged during driver load, code consolidation (removal of
redundant link negotiation logic during initialize_adaoter()), and
finilly, the driver no longer needs to defer the fc_remote_port_add()
calls to hold off lun-scanning prior to returning from the probe()
function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch makes some needlessly global functions static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Drop queue-depths across all luns for a given fcport
during TASK_SET_FULL statuses.
- Ramp-up I/Os after throttling.
- Consolidate completion-status handling of CS_QUEUE_FULL with
CS_COMPLETE as ISP24xx firmware no longer reports
CS_QUEUE_FULL.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Early ISP2432 parts have a known hardware issue when coming
out of a D3 hot state. This issue can result in a hung PCIe
link. Recent firmwares contain a workaround whereby the
stop-firmware mailbox command prevents the ISP from entering
the D3 hot state.
In order to ensure that the workaround succeeded the driver
must verify that the stop-firmware mailbox command completes
successfully. In the event of a failure, the driver
attempts a shutdown-retry after resetting the ISP and
re-executing firmware.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
commit 0181944fe6 adds a
'extended_error_logging' global variable to qla2xxx which is defined by
qla4xxx too.
Trying to build both drivers results in the following error:
LD drivers/scsi/built-in.o
drivers/scsi/qla4xxx/built-in.o: In function `qla4xxx_slave_configure':
drivers/scsi/qla4xxx/ql4_os.c:1433: multiple definition of `extended_error_logging'
drivers/scsi/qla2xxx/built-in.o:drivers/scsi/qla2xxx/qla_os.c:2166:
first defined here
make[2]: *** [drivers/scsi/built-in.o] Error 1
make[1]: *** [drivers/scsi] Error 2
make: *** [drivers] Error 2
The following patch simply adds a qla2_ (qla4_ respectively) prefix to
the variable name.
Signed-off-by: Frederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stall error handler if attempting recovery while an rport is
blocked. This avoids device offline scenarios due to errors in
the error handler.
Reference implementation from lpfc/mptfc.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
iIDMA (Intelligent Interleaved Direct Memory Access) allows for
the HBA hardware to send FC frames at the rate at which they can
be received by a target device. By taking advantage of the
higher link rate, the HBA can maximize bandwidth utilization in a
heterogeneous multi-speed SAN.
Within a fabric topology, port speed detection is done via a Name
Server command (GFPN_ID) followed by a Fabric Management command
(GPSC). In an FCAL/N2N topology, port speed is based on the HBA
link-rate.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code attempts to retry PLOGIs to fcports that are
FCP_TARGETs only. If the driver never performed a successful
PLOGI/PRLI, the port-type would never be assigned, and the
relogin logic would silently drop the request (and thus the port
would not be recognized and registered).
The fix is relatively straightforward, drop the FCP_TARGET-only
check.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently it is impossible to reset provided by Qlogic QLA2xxx driver
SCSI devices externally using corresponding sg devices, particularly via
sg_reset utility, because qla2xxx driver in qla2xxx_eh_device_reset()
function checks if the input scsi_cmnd has its private data (CMD_SP())
attached. Then the found pointer isn't used anywhere inside of
qla2xxx_eh_device_reset(). If the RESET request comes from sg device, it
doesn't have such private data.
The attached patch removes check for non-NULL CMD_SP() from
qla2xxx_eh_device_reset(), hence allows to reset QLA2xxx's devices using
corresponding sg devices.
AV: change applies to bus/host reset handlers as well.
Signed-off-by: Vladislav Bolkhovitin <vst@vlnb.net>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Conflicts:
drivers/scsi/nsp32.c
drivers/scsi/pcmcia/nsp_cs.c
Removal of randomness flag conflicts with SA_ -> IRQF_ global
replacement.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add a few spaces to MODULE_PARM_DESC() text for qla2xxx. Without these
spaces text runs together when modinfo prints the text.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Acked-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also remove qla2xxx_probe_one/qla2xxx_remove_one stubs previously
used with external firmware module loaders.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Similar in form to QLogic's standard offering -- via
the 'extended_error_logging' module parameter.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- macro usage statements should terminate with a ';'
- remove unused macros.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Defer firmware dump-data raw-to-textual conversion to
user-space.
- Add module parameter (ql2xallocfwdump) to allow for per-HBA
allocations of firmware dump memory.
- Dump request and response queue data as per firmware group
request.
- Add extended firmware trace support for ISP24XX/ISP54XX chips.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Simplify and centralise buffer allocation/deallocation, as
there's no point in having two memory request methods.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Expandind on the previous commit:
commit 79f89a4296
Author: andrew.vasquez@qlogic.com <andrew.vasquez@qlogic.com>
Date: Fri Jan 13 17:05:58 2006 -0800
[SCSI] qla2xxx: Disable port-type RSCN handling via driver state-machine.
and given:
- the process-context requirements of the FC transport
rport-APIs.
- lack of port-type RSCN processing logic for ISP24xx and newer
chips.
it's time now to remove the state-machine logic from mainline.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix the driver to return SUCCESS if the firmware or driver doesn't
have a command to abort, i.e., it's already been returned. Without
this patch, error recovery will take the target offline as it tries
harder and harder to get the driver to return the command it no longer
has.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qla2x00_probe_one() fails before calling request_irq() but gets to
qla2x00_free_device() then it will mistakenly try to free an irq it didn't
request. It's chosing to free based on ha->pdev->irq which is always set.
host->irq is set after request_irq() succeeds so let's use that to decide
to free or not.
This was observed and tested when a silly set of circumstances lead to
firmware loading failing on a 2100.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Modify well over a dozen mempool users to call mempool_create_slab_pool()
rather than calling mempool_create() with extra arguments, saving about 30
lines of code and increasing readability.
Signed-off-by: Matthew Dobson <colpatch@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ISP24XX FW does not support Mbx 0x74 ie Login Local Port.
Added the equivalent code for ISP24XX ie to relogin in non
fabric case for ISP24XX use login iocb.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Only support ZIO mode 6 on specific ISP types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
As new 23xx firmware will accomidate ISP63xx types.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Chip is similar in form to our ISP24xx offering.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use the kthread_ API instead of opencoding lots of hairy code for kernel
thread creation and teardown.
Also switch from semaphore-based thread wakeup to wake_up_process.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-By: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Commit 854165f424
inadvertently added some code meant only for testing -- the
driver was ignoring the non-zero function numbers of a
multi-port HBA.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fcport visibility is recognized during interrupt time, but,
rport removal can only occur during a process
(sleeping)-context. Return a DID_IMM_RETRY status for
commands submitted within this window to insure I/Os do not
prematurely run-out of retries.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A target can LOGO an initiator at any time (i.e. during I/O,
due to a controller hicup, or as a simple authentication
mechanism after an initial CDB command), when this occurs,
the driver attempts to relogin (PLOGI) to the device via the
DPC thread. Add code to make the appropriate upcall to the
FC transport layer (fc_remote_port_add()) upon successful
completion of the PLOGI.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver can typically detect port-loss during an
interrupt context (i.e. via interrogation of a status IOCB's
completion status [CS_PORT_LOGGED_OUT]. Due to the calling
requirements of the fc_rport APIs, the driver would defer
removal of the device to the default workqueue. If the
work-item was preceded by an event which caused the port to
obtain visibility (relogin successful, target re-logged into
the topology), deferred removal could inadvertently drop the
rport. The code also no longer defers removal via the
default workqueue, instead opting for use of the driver's
own DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Given the semantic changes in both the device-model and
fc-transport APIs, the driver's handling of port-type RSCNs
via a series of ADISCs and PLOGIs can cause series of
badness ranging from unexpectedly device loss to devices not
being discovered.
In the interim, disable (via a module-parameter) this
feature and allow RSCN management to continue to occur
within the driver's DPC thread.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Transition driver to exclusively use the request_firmware()
interfaces to retrieve firmware-blobs from user-space. This
will be the default behaviour going forward until the
embedded firmware-binary images are removed from the
upstream kernel.
Upon request, the driver caches the firmware image until the
driver is unloaded.
NOTE: The option is present to allow the user to continue to
use the firmware-loader modules, but, should be considered
deprecated.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
We recently went back to implement a board reset. When we perform the
reset, we wanted to tear down the internal data structures and rebuild
them. Unfortunately, when it came to the rport structure, things were
odd. If we deleted them, the scsi targets and sdevs would be
torn down. Not a good thing for a temporary reset. We could block the
rports, but we either maintain the internal structures to keep the
rport reference (perhaps even replicating what's in the transport),
or we have to fatten the fc transport with new search routines to find
the rport (and deal with a case of a dangling rport that the driver
forgets).
It dawned on me that we had actually reached this state incorrectly.
When the fc transport first started, we did the block/unblock first, then
added the rport interface. The purpose of block/unblock is to hide the
temporary disappearance of the rport (e.g. being deleted, then readded).
Why are we making the driver do the block/unblock ? We should be making
the transport have only an rport add/delete, and the let the transport
handle the block/unblock.
So... This patch removes the existing fc_remote_port_block/unblock
functions. It moves the block/unblock functionality into the
fc_remote_port_add/delete functions. Updates for the lpfc driver are
included. Qlogic driver updates are also enclosed, thanks to the
contributions of Andrew Vasquez. [Note: the qla2xxx changes are
relative to the scsi-misc-2.6 tree as of this morning - which does
not include the recent patches sent by Andrew]. The zfcp driver does
not use the block/unblock functions.
One last comment: The resulting behavior feels very clean. The LLDD is
concerned only with add/delete, which corresponds to the physical
disappearance. However, the fact that the scsi target and sdevs are
not immediately torn down after the LLDD calls delete causes an
interesting scenario... the midlayer can call the xxx_slave_alloc and
xxx_queuecommand functions with a sdev that is at the location the
rport used to be. The driver must validate the device exists when it
first enters these functions. In thinking about it, this has always
been the case for the LLDD and these routines. The existing drivers
already check for existence. However, this highlights that simple
validation via data structure dereferencing needs to be watched.
To deal with this, a new transport function, fc_remote_port_chkready()
was created that LLDDs should call when they first enter these two
routines. It validates the rport state, and returns a scsi result
which could be returned. In addition to solving the above, it also
creates consistent behavior from the LLDD's when the block and deletes
are occuring.
Rejections fixed up and
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Ok, here's a patch to add such a common API for fc transport users.
Relevant LLD changes (lpfc and qla2xxx) also present.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Here's a patch which drops the eh_active checks in the qla2xxx
eh_handler callbacks.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
ISP23xx and ISP24xx chips have support for an adaptive
method of posting SCSI command completions for multiple SCSI
commands during a single system interrupt.
SCSI commands are placed on the system response queue
without interrupting the host until 1) a delay timer
expires; or 2) a SCSI command completes with an error.
As long as the host software (qla2xxx) services the response
queue for completions (this polling is done during
queuecommand()) within the 'delay timer' period, the
firmware will not generate system interrupt.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If qla2x00_probe_one()'s call to qla2x00_iospace_config() fails, we call
qla2x00_free_device() to clean up. But because ha->dpc_pid hasn't been set
yet, qla2x00_free_device() tries to stop a kernel thread which hasn't started
yet. It does wait_for_completion() against an uninitialised completion struct
and the kernel hangs up.
Fix it by initialising ha->dpc_pid a bit earlier.
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On ISP24xx parts, stop execution of firmware during ISP
tear-down.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Nishanth Aravamudan <nacc@us.ibm.com>
Replace schedule_timeout() with
msleep()/msleep_interruptible() as appropriate, to guarantee the task
delays as expected.
Signed-off-by: Nishanth Aravamudan <nacc@us.ibm.com>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
fc_remove_host() should only be called after a scsi_host has
been successfully added via scsi_add_host() -- any failures
while qla2xxx probing would result in an incorrect call to
fc_remove_host() during cleanup.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Export additional host information via the shost_attrs member in
the scsi_host template. Attributes include: driver version,
firmware version, ISP serial number, ISP type, ISP product ID,
HBA model name, HBA model description, PCI interconnect
information, and HBA port state.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove redundant qla2x00_target_reset() function in favour of
the equivalent qla2x00_device_reset(). Update callers of
old function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In order to efficiently utilise the ISP's IOCB
request-queue, use the dma_get_required_mask() function to
determine the use of command-type 2 or 3 IOCBs when queueing
SCSI commands. This applies to ISP2[123]xx chips only, as
the ISP24xx uses command-type 7 IOCBs which use 64bit DSDs.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleanup FC remote port registration.
Due to the inherent behaviour (an immediate scan) of adding
a 'target'-role-capable rport via fc_remote_port_add(),
split the registration into two steps -- addition as
unknown-type role, then use fc_remote_port_rolchg() with
appropriate role (based on PLOGI/PRLI bits). This allows
for a more cleaner rport->dd_data management as can be seen
with the simplified qla2xxx_slave_alloc() function.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add firmware version number to qla24xx_fw_version_str().
Original code was accidently trimmed during port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add OS initialization codes for ISP24xx recognition.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx flash-manipulation routines.
Add read/write flash manipulation routines for the ISP24xx.
Update sysfs NVRAM objects to use generalized accessor
functions.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ISP24xx definitions.
Add requisite structure definitions and #define's for ISP24xx
support. Also drop volatile modifiers from device_reg_* register
layouts as the members are never really accessed, only their
offsets within the layout are used during reads and writes.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Factor-out ISP specific functions to method-based call tables.
In anticipation of ISP24xx/ISP25xx support, factor-out ISP
specific functions into a method-based call table.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Return to previous held-logic of calling scsi_add_host() only
after the board has been completely initialized. Also return
pci_*() error-codes during probe failure paths.
This also corrects an issue where only lun 0 is being scanned for
a given port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Correct incorrect locking order in qla2xxx_eh_abort() handler which
would case a hang during certain code-paths.
With extra pieces to fix the irq state in the locks.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original from: Christoph Hellwig <hch@lst.de>
Modified and
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make transport-functions structure non-static. Replace #include of
scsi_transport.h with a forward declaration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove internal lun discovery routines and support
structures.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add initial support for FC remote port infrastructure.
o Use fc_remote_port...() registration and block/unlock
functions.
o Consolidate 'attribute' (fc-remote/sysfs) helpers into
new qla_attr.c file.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove internal command queuing from the driver. As is, this
driver cannot tolerate cable-pulls as I/Os will begin to fail
by the upper layers.
o Should be used in conjuction with the
11-fc_rport_adds_2.diff patch.
o Removes qla_listops.h file -- no longer needed.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
