To be more readable code, this patch adds
new for_each_card_prelinks() macro, and replace existing code to it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1381093 ("Missing break in switch")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now when a helper for unreferencing device nodes is available
we can get rid of the local implementation.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The I2S controller can handle sample rates only up to 96000 and the CPU DAI
has already related constraint set so drop the impossible 176400, 192000
switch cases.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In case of sample rates lower than 44100 currently there is too low MCLK
frequency set for the CODEC. Playback fails with following errors:
$ speaker-test -c2 -t sine -f 1500 -l2 -r 32000
Sine wave rate is 1500.0000Hz
Rate set to 32000Hz (requested 32000Hz)
Buffer size range from 128 to 131072
Period size range from 64 to 65536
Using max buffer size 131072
Periods = 4
Unable to set hw params for playback: Invalid argument
Setting of hwparams failed: Invalid argument
[ 497.883700] max98090 1-0010: Invalid master clock frequency
To fix this the I2S root clock's frequency is increased, depending
on sampling rate.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch updates the driver so, in addition to current DT bindings, it
also can also use the new DT bindings with cpu, codec subnodes which allow
to support sound on the HDMI interface.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The RCLKSRC mux input 0 is a default configuration after reset, so
there is no need for this explicit snd_soc_dai_set_sysclk() call.
Also, this static mux clock configuration can be specified in DT.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
As the RCLK clock may be updated through the common clk API before each
snd_soc_dai_ops::trigger call, it is not enough to update i2s->rclk_srcrate
only once after it has been initially set to 0. To avoid wrong PSR values
we always get RCLK frequency from the CLK_I2S_RCLK_SRC clock, when that
clock is available.
Fixes: e1417fdf3011 "ASoC: samsung: i2s: Ensure the RCLK rate is properly determined"
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Odroid boards are manufactured by Hardkernel, not Samsung. New compatible
string entries are added, with "hardkernel," instead of "samsung," vendor
prefix. Support for the old compatible strings is going to be removed after
some time.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch defines I2S1 - HDMI DAI link and implements related
hw_params callback. The AUD PLL frequency is configured through
the CLK_SCLK_I2S1 leaf clock, the exynos5433 clock tree
definitions are updated in a separate patch.
The device tree parsing part is changed is a way it supports older
DTBs with just a single CPU DAI specified, without the HDMI link.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The SAMSUNG_I2S_OPCLK is not currently used by any card driver thus we can
safely change semantics of 'dir' argument of the I2S set_sysclk() callback.
Now an enumeration is exported instead of directly using register bit field
values.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
It seems both PCLK_I2S1 and SCLK_I2S1 clocks need to be enabled before
I2S1 control registers can be accessed on exynos5433. If SCLK clock
is disabled an exception is triggered. To fix this parent clock of
the RCLK_SRC clock is assigned to pri_dai->op_clk so required gate
clock is handled by the runtime PM ops.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
In order to support multiple instances of the I2S IP block the platform
device name is prepended to each clock registered by the driver.
The clock-output-names property is now not used, this should not cause
any issues as, for example, CDCLK clock is referenced through DT 'clocks'
property, not by name.
This change allows to have both I2S0 and I2S1 enabled simultaneously
on exynos5433 and working properly when #clock-cells property is specified
in respective DT nodes.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Clean makefile rules about inexistant files.
Thoses files were removed in commit a076d41823 ("ASoC: samsung: Drop AC97 drivers")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Now platform can be replaced to component, let's do it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
If the RCLK mux clock configuration is specified in DT and no set_sysclk()
callback is used in the sound card driver the sclk_srcrate field will remain
set to 0, leading to an incorrect PSR divider setting.
To fix this the frequency value is retrieved from the CLK_I2S_RCLK_SRC clock,
so the actual RCLK mux selection is taken into account.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
rtd->codec will be removed soon.
rtd->codec = rtd->codec_dai->codec, thus,
we can use rtd->codec_dai->component instead of it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
I've been quite lax in sending these due to conference season but here's
a fairly large collection of ASoC updates. The one thing that's not
device specific is Takashi's fix for races between delayed work and PCM
destruction, otherwise everything is specific to an individual device.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlnx7QsTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0H6gB/9Kg6nfaNQDH3ScDO/0KXJevvc9DZUG
1Mgb6o866WQKVKwHL4/7PeUnwpaAh/Dr5KN7bFS7nImrZlHiJfv64Cmrrca+VMwa
O9SnAxbzMDN1MXV3uLDlmd5jJ2EETGnSSo31gjyOuFAmvWRYhtvN4QtoLRBQYYJ9
A32JAKYXKpdjYlIq8sssf1Ey9OcReho3klAc578Yw5qsuHTsB8yJ5SNy0YgmobCm
rNs+LcY9fBPQxY1nVW5iJ3L8oR9RXlUOdZy1I220i0q6+ku1nynbh64V8m7fFGmp
KQLIVvH8JGlqaGBidU47C3vwEnUN88y0+98i9dF4Hc26E+Ml3YNyL/z6
=TVgt
-----END PGP SIGNATURE-----
gpgsig -----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAloGGn8THGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0BAsB/9tbgkbKpUVsWEQOTXDtz1VARb5+zxJ
zMRmYGdcfV+au4pmo07NwcxwFDqeLxmsd7dRM+eoPJGbxklD9rr9eL9tZiO1TI0B
jla9eyKO1aRjCD8dEDsQJEUjDGWWbrpYRvFjlTmYW5cf1vgE9Ta7QtwBN+mK+Ssn
1PtwfHg5lDffoCMGOgu/5Kah4QhzAIU1mM4Vg77VgsuScZEw5qMYJUncfkdsH6M5
JiQJpOQR/wNL4/IETodjhFzqhi9vlUvDEfmATNMpHMdHA//erUbphUt2bAjqVauM
zKTFTSN1vvW1GirJyxz4NiHXQ6upbpZPMDcPsfOzJhHw82OAwx/pp1QT
=bBtM
-----END PGP SIGNATURE-----
Merge tag 'asoc-fix-v4.14-rc6' into asoc-linus
ASoC: Fixes for v4.14
I've been quite lax in sending these due to conference season but here's
a fairly large collection of ASoC updates. The one thing that's not
device specific is Takashi's fix for races between delayed work and PCM
destruction, otherwise everything is specific to an individual device.
# gpg: Signature made Thu 26 Oct 2017 15:11:23 BST
# gpg: using RSA key ADE668AA675718B59FE29FEA24D68B725D5487D0
# gpg: issuer "broonie@kernel.org"
# gpg: Good signature from "Mark Brown <broonie@sirena.org.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@debian.org>" [unknown]
# gpg: aka "Mark Brown <broonie@kernel.org>" [unknown]
# gpg: aka "Mark Brown <broonie@tardis.ed.ac.uk>" [unknown]
# gpg: aka "Mark Brown <broonie@linaro.org>" [unknown]
# gpg: aka "Mark Brown <Mark.Brown@linaro.org>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: 3F25 68AA C269 98F9 E813 A1C5 C3F4 36CA 30F5 D8EB
# Subkey fingerprint: ADE6 68AA 6757 18B5 9FE2 9FEA 24D6 8B72 5D54 87D0
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Secondary DAI in Exynos I2S driver is not used by any of the currently
supported boards and it causes problems due to some limitations in the
ASoC code. Disable it until it gets proper support both by board-specific
and ASoC core code. Also disable IDMA support, which relies on secondary
DAI presence.
This patch fixes following kernel warning:
samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
samsung-i2s 3830000.i2s: ASoC: Failed to create component debugfs directory
------------[ cut here ]------------
WARNING: CPU: 3 PID: 82 at fs/proc/generic.c:330 proc_register+0xec/0x10c
proc_dir_entry 'sub0/prealloc' already registered
Modules linked in:
CPU: 3 PID: 82 Comm: kworker/3:1 Not tainted 4.14.0-rc5-next-20171017 #3089
Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
Workqueue: events deferred_probe_work_func
[<c0110114>] (unwind_backtrace) from [<c010c900>] (show_stack+0x10/0x14)
[<c010c900>] (show_stack) from [<c083e664>] (dump_stack+0x90/0xc8)
[<c083e664>] (dump_stack) from [<c011d2b8>] (__warn+0xd4/0x100)
[<c011d2b8>] (__warn) from [<c011d384>] (warn_slowpath_fmt+0x38/0x48)
[<c011d384>] (warn_slowpath_fmt) from [<c0271268>] (proc_register+0xec/0x10c)
[<c0271268>] (proc_register) from [<c027130c>] (proc_create_data+0x84/0xc8)
[<c027130c>] (proc_create_data) from [<c061afbc>] (snd_info_register+0x64/0xcc)
[<c061afbc>] (snd_info_register) from [<c062a6e0>] (snd_pcm_lib_preallocate_pages1+0x78/0x1a0)
[<c062a6e0>] (snd_pcm_lib_preallocate_pages1) from [<c063eef4>] (dmaengine_pcm_new+0xa0/0x1ec)
[<c063eef4>] (dmaengine_pcm_new) from [<c062b9f8>] (snd_soc_platform_drv_pcm_new+0x1c/0x28)
[<c062b9f8>] (snd_soc_platform_drv_pcm_new) from [<c063d54c>] (soc_new_pcm+0x2f4/0x4f4)
[<c063d54c>] (soc_new_pcm) from [<c063107c>] (snd_soc_register_card+0xc4c/0xdc4)
[<c063107c>] (snd_soc_register_card) from [<c063db30>] (devm_snd_soc_register_card+0x34/0x70)
[<c063db30>] (devm_snd_soc_register_card) from [<c064af60>] (asoc_simple_card_probe+0x230/0x47c)
[<c064af60>] (asoc_simple_card_probe) from [<c047f8fc>] (platform_drv_probe+0x50/0xb0)
[<c047f8fc>] (platform_drv_probe) from [<c047dee0>] (driver_probe_device+0x2a0/0x46c)
[<c047dee0>] (driver_probe_device) from [<c047c0bc>] (bus_for_each_drv+0x44/0x8c)
[<c047c0bc>] (bus_for_each_drv) from [<c047db50>] (__device_attach+0xa0/0x134)
[<c047db50>] (__device_attach) from [<c047cf7c>] (bus_probe_device+0x88/0x90)
[<c047cf7c>] (bus_probe_device) from [<c047d484>] (deferred_probe_work_func+0x3c/0x168)
[<c047d484>] (deferred_probe_work_func) from [<c01371f8>] (process_one_work+0x188/0x41c)
[<c01371f8>] (process_one_work) from [<c01374b4>] (process_scheduled_works+0x28/0x38)
[<c01374b4>] (process_scheduled_works) from [<c01376d4>] (worker_thread+0x210/0x4dc)
[<c01376d4>] (worker_thread) from [<c013d9cc>] (kthread+0x128/0x164)
[<c013d9cc>] (kthread) from [<c0108848>] (ret_from_fork+0x14/0x2c)
---[ end trace bad8db6ee771d094 ]--
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
devm_gpiod_get is called with GPIOF_OUT_INIT_LOW but the function doesn't
allow the parameters. Unluckily, GPIOF_OUT_INIT_LOW is same value as
GPIOD_ASIS and gpio direction isn't set properly.
Muted stream comes up when I try recording some sounds on TM2. mic-bias
gpiod state can't be changed because the gpiod is created with the invalid
parameter. The gpio should be set GPIOD_OUT_HIGH.
Fixes: 1bfbc260a5 ("ASoC: samsung: Add machine driver for Exynos5433 based TM2 board")
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add specific cpu_dai_name to dai_link because samsung i2s driver registers
two dais and components. Selecting one of them clearly is needed more
information like cpu_dai_name, of_node. The reason why the dai_links have
to use 'samsung-i2s' for cpu_dai is that 'samsung-i2s-sec' doesn't have a
capture functionality.
Without this code, cpu_dai will be selected the first one of the
component_list. For example, if I describe nothing to cpu_dai_name,
'samsung-i2s-sec' might be selected to HiFi Primay.
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add specific dais name when components are registered. Component and dai
name will follow their parent dev name, if the name isn't described. In
case of this driver, each dais will have same name like '11440000.i2s0' by
fmt_single_name function.
The problem having same name is that TM2 machine driver can't detect
capture devices correctly. Machine driver doesn't know which one is proper
to use for cpu dai. The driver just selects to use 'samsung-i2c-sec' that
doesn't have capture functionality because the component of
samsung-i2s-sec is located in the first of the component_list.
I add dai name like 'samsung-i2s', 'samsung-i2s-sec' for each dais. The
reason why adding dai id to 1 is that it doesn't allow to use particular
dai name in case of when I use 0 for dai id.
Signed-off-by: Jaechul Lee <jcsing.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If 'clk_prepare_enable()' fails, we must 'put' the corresponding clock.
Othewise, there is a resource leak.
Fixes: f5c97c7b04 ("ASoC: samsung: i2s: Handle return value of clk_prepare_enable.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Mark Brown <broonie@kernel.org>
Since jack gpios are managed via devres, we don't have to call
snd_jack_free_gpios() at release any longer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
First of all,the address of pdev->dev is assigned to card->dev,then
the function platform_set_drvdata copies the value the variable card
to pdev->dev.driver_data, but when calling snd_soc_register_card,the
function dev_set_drvdata(card->dev, card) will also do the same copy
operation,so i think that the former copy operation can be removed.
Signed-off-by: Peng Donglin <dolinux.peng@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make these const as they are only stored in the ops field of a
snd_soc_dai_link structure, which is const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
If (quirks & QUIRK_SEC_DAI == 0) then samsung_i2s_probe() doesn't allocate
sec_dai and pri_dai->sec_dai remains Null, but samsung_i2s_remove()
performs pri_dai->sec_dai dereference in any case.
The patch removes useless reinitialization of sec_dai at
samsung_i2s_remove(), because resources are under devm control.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Anton Vasilyev <vasilyev@ispras.ru>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Make this const as it is only passed as the 2nd argument to the function
devm_snd_soc_register_platform, which is of type const.
Done using Coccinelle.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
snd_pcm_ops are not supposed to change at runtime. All functions
working with snd_pcm_ops provided by <sound/soc.h> work with
const snd_pcm_ops. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
tm2_dapm_widgets and tm2_pm_ops are local to the source and do not need
to be in global scope, so make them static.
Cleans up sparse warnings:
symbol 'tm2_dapm_widgets' was not declared. Should it be static?
symbol 'tm2_pm_ops' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
As suggested in reviews the requirement of clocks in the 'sound' node
is dropped and instead a leaf clock is used to configure frequency
of the audio root clock PLL. This can work now after the clock tree
definitions have been updated to allow clock rate setting propagation
on the path from the I2S controller up to the EPLL.
This patch also lowers the CODEC master clock frequency so as
to not exceed the maximum allowed 60 MHz at maximum audio sampling
rates.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
s3c2412_i2s_probe() might fail so driver has to revert work done by
s3c_i2sv2_probe() (clock enabling). Missing doing this would lead to
clock enable in-balance.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The s3c_i2sv2_probe() only enabled iis clock. Missing prepare isn't
probably fatal, because for SoC clocks this is usually no-op, but for
correctness this clock should be prepared.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arvind Yadav<arvind.yadav.cs@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Commit 87b132bc03 ("ASoC: samsung: s3c24{xx,12}-i2s: port to use
generic dmaengine API") moved ioremap() call from
s3c-i2s-v2.c:s3c_i2sv2_probe() to s3c2412-i2s.c:s3c2412_iis_dev_probe()
and converted it to devm- resource managed interface.
However the error path in first of them - s3c_i2sv2_probe() - was not
updated. If getting a iis clock in s3c_i2sv2_probe() failed, the
address space would be unmapped there. This could lead to:
1. double iounmap() later from devm-interface of s3c2412_iis_dev_probe()),
2. accessing the memory by other functions in s3c2412-i2s.c unit.
Anyway, the owner of this mapped region should be s3c2412-i2s.c because
it starts the mapping.
Affected are drivers for S3C24xx family although issue was not reproduced.
Fixes: 87b132bc03 ("ASoC: samsung: s3c24{xx,12}-i2s: port to use generic dmaengine API")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Arvind Yadav<arvind.yadav.cs@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
