Add some comments about known GPIO settings of supported board
versions.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
After that Anysee I2C adapter is capable of one and two byte long
I2C addresses in case of read from I2C bus.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Looks like it is IF route switch on IOE[0]. Set it correctly
to route signal from tuner to demod. Now it works for DVB-C too.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is ZL10353, TDA10023 and TDA18212.
Tuner is inside of Samsung DNOD44CDH086A tuner module.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New models have new NXP TDA18212 silicon tuner.
Not tested yet due to lack of HW...
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use board ID as base value when selecting correct hardware configuration.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Print firmware version as two digit long (change from 3 to 2).
Windows app have changed that too. First byte was hard coded as 0.
Change email list address to report non-working device to current one.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It can read more than one byte from I2C bus. Allow that.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Make a user visible driver version change, for the inevitable user support
questions about why newer model HVR-1600's do not work with (older
versions of) the cx18 driver.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A previous changes which added the newer model HVR-1600's and DTV support for
them, neglected to add RF analog TV for them. Fix RF analog TV for the newer
HVR-1600's which have a worldwide analog tuner assembly with a TDA18271 tuner
and TDA8295 demodulator.
Thanks go to Jeff Campbell and Mike Bradley for reproting the problem, and
also to Mike Bradley for doing a lot of the legwork to figure out the tuner
reset GPIO line, the demodulator I2C address, and that the GPIOs have to be
reinitialized after a cardtype switch.
Reported-by: Jeff Campbell <jac1dlists@gmail.com>
Tested-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Introduce SCHED_LOAD_RESOLUTION, which scales is added to
SCHED_LOAD_SHIFT and increases the resolution of
SCHED_LOAD_SCALE. This patch sets the value of
SCHED_LOAD_RESOLUTION to 10, scaling up the weights for all
sched entities by a factor of 1024. With this extra resolution,
we can handle deeper cgroup hiearchies and the scheduler can do
better shares distribution and load load balancing on larger
systems (especially for low weight task groups).
This does not change the existing user interface, the scaled
weights are only used internally. We do not modify
prio_to_weight values or inverses, but use the original weights
when calculating the inverse which is used to scale execution
time delta in calc_delta_mine(). This ensures we do not lose
accuracy when accounting time to the sched entities. Thanks to
Nikunj Dadhania for fixing an bug in c_d_m() that broken fairness.
Below is some analysis of the performance costs/improvements of
this patch.
1. Micro-arch performance costs:
Experiment was to run Ingo's pipe_test_100k 200 times with the
task pinned to one cpu. I measured instruction, cycles and
stalled-cycles for the runs. See:
http://thread.gmane.org/gmane.linux.kernel/1129232/focus=1129389
for more info.
-tip (baseline):
Performance counter stats for '/root/load-scale/pipe-test-100k' (200 runs):
964,991,769 instructions # 0.82 insns per cycle
# 0.33 stalled cycles per insn
# ( +- 0.05% )
1,171,186,635 cycles # 0.000 GHz ( +- 0.08% )
306,373,664 stalled-cycles-backend # 26.16% backend cycles idle ( +- 0.28% )
314,933,621 stalled-cycles-frontend # 26.89% frontend cycles idle ( +- 0.34% )
1.122405684 seconds time elapsed ( +- 0.05% )
-tip+patches:
Performance counter stats for './load-scale/pipe-test-100k' (200 runs):
963,624,821 instructions # 0.82 insns per cycle
# 0.33 stalled cycles per insn
# ( +- 0.04% )
1,175,215,649 cycles # 0.000 GHz ( +- 0.08% )
315,321,126 stalled-cycles-backend # 26.83% backend cycles idle ( +- 0.28% )
316,835,873 stalled-cycles-frontend # 26.96% frontend cycles idle ( +- 0.29% )
1.122238659 seconds time elapsed ( +- 0.06% )
With this patch, instructions decrease by ~0.10% and cycles
increase by 0.27%. This doesn't look statistically significant.
The number of stalled cycles in the backend increased from
26.16% to 26.83%. This can be attributed to the shifts we do in
c_d_m() and other places. The fraction of stalled cycles in the
frontend remains about the same, at 26.96% compared to 26.89% in -tip.
2. Balancing low-weight task groups
Test setup: run 50 tasks with random sleep/busy times (biased
around 100ms) in a low weight container (with cpu.shares = 2).
Measure %idle as reported by mpstat over a 10s window.
-tip (baseline):
06:47:48 PM CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle intr/s
06:47:49 PM all 94.32 0.00 0.06 0.00 0.00 0.00 0.00 0.00 5.62 15888.00
06:47:50 PM all 94.57 0.00 0.62 0.00 0.00 0.00 0.00 0.00 4.81 16180.00
06:47:51 PM all 94.69 0.00 0.06 0.00 0.00 0.00 0.00 0.00 5.25 15966.00
06:47:52 PM all 95.81 0.00 0.00 0.00 0.00 0.00 0.00 0.00 4.19 16053.00
06:47:53 PM all 94.88 0.06 0.00 0.00 0.00 0.00 0.00 0.00 5.06 15984.00
06:47:54 PM all 93.31 0.00 0.00 0.00 0.00 0.00 0.00 0.00 6.69 15806.00
06:47:55 PM all 94.19 0.00 0.06 0.00 0.00 0.00 0.00 0.00 5.75 15896.00
06:47:56 PM all 92.87 0.00 0.00 0.00 0.00 0.00 0.00 0.00 7.13 15716.00
06:47:57 PM all 94.88 0.00 0.00 0.00 0.00 0.00 0.00 0.00 5.12 15982.00
06:47:58 PM all 95.44 0.00 0.00 0.00 0.00 0.00 0.00 0.00 4.56 16075.00
Average: all 94.49 0.01 0.08 0.00 0.00 0.00 0.00 0.00 5.42 15954.60
-tip+patches:
06:47:03 PM CPU %usr %nice %sys %iowait %irq %soft %steal %guest %idle intr/s
06:47:04 PM all 100.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 16630.00
06:47:05 PM all 99.69 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.31 16580.20
06:47:06 PM all 99.69 0.00 0.06 0.00 0.00 0.00 0.00 0.00 0.25 16596.00
06:47:07 PM all 99.20 0.00 0.74 0.00 0.00 0.06 0.00 0.00 0.00 17838.61
06:47:08 PM all 100.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 16540.00
06:47:09 PM all 100.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 16575.00
06:47:10 PM all 100.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.00 16614.00
06:47:11 PM all 99.94 0.00 0.00 0.00 0.00 0.00 0.00 0.00 0.06 16588.00
06:47:12 PM all 99.94 0.00 0.06 0.00 0.00 0.00 0.00 0.00 0.00 16593.00
06:47:13 PM all 99.94 0.00 0.06 0.00 0.00 0.00 0.00 0.00 0.00 16551.00
Average: all 99.84 0.00 0.09 0.00 0.00 0.01 0.00 0.00 0.06 16711.58
We see an improvement in idle% on the system (drops from 5.42% on -tip to 0.06%
with the patches).
We see an improvement in idle% on the system (drops from 5.42%
on -tip to 0.06% with the patches).
Signed-off-by: Nikhil Rao <ncrao@google.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Nikunj A. Dadhania <nikunj@linux.vnet.ibm.com>
Cc: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Cc: Stephan Barwolf <stephan.baerwolf@tu-ilmenau.de>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Link: http://lkml.kernel.org/r/1305754668-18792-1-git-send-email-ncrao@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
SCHED_LOAD_SCALE is used to increase nice resolution and to
scale cpu_power calculations in the scheduler. This patch
introduces SCHED_POWER_SCALE and converts all uses of
SCHED_LOAD_SCALE for scaling cpu_power to use SCHED_POWER_SCALE
instead.
This is a preparatory patch for increasing the resolution of
SCHED_LOAD_SCALE, and there is no need to increase resolution
for cpu_power calculations.
Signed-off-by: Nikhil Rao <ncrao@google.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Nikunj A. Dadhania <nikunj@linux.vnet.ibm.com>
Cc: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Cc: Stephan Barwolf <stephan.baerwolf@tu-ilmenau.de>
Cc: Mike Galbraith <efault@gmx.de>
Link: http://lkml.kernel.org/r/1305738580-9924-3-git-send-email-ncrao@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Avoid using long repetitious names; make this simpler and nicer
to read. No functional change introduced in this patch.
Signed-off-by: Nikhil Rao <ncrao@google.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Cc: Nikunj A. Dadhania <nikunj@linux.vnet.ibm.com>
Cc: Srivatsa Vaddagiri <vatsa@linux.vnet.ibm.com>
Cc: Stephan Barwolf <stephan.baerwolf@tu-ilmenau.de>
Cc: Mike Galbraith <efault@gmx.de>
Link: http://lkml.kernel.org/r/1305738580-9924-2-git-send-email-ncrao@google.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the case of x2apic cluster mode we can group IPI register
writes based on the cluster group instead of individual per-cpu
destination messages.
This reduces the apic register writes and reduces the amount of
IPI messages (in the best case we can reduce it by a factor of
16).
With this change, the cost of flush_tlb_others(), with the flush
tlb IPI being sent from a cpu in the socket-1 to all the logical
cpus in socket-2 (on a Westmere-EX system that has 20 logical
cpus in a socket) is 3x times better now (compared to the former
'send one-by-one' algorithm).
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: steiner@sgi.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110519234637.512271057@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
In the case of x2apic cluster mode, we can group IPI register
writes based on the cluster group instead of individual per-cpu
destination messages.
For this purpose, track the cpu's that belong to the same x2apic
cluster.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: steiner@sgi.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110519234637.421800999@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Use the unused probe routine in the apic driver to finalize the
apic model selection. This cleans up the
default_setup_apic_routing() and this probe routine in future
can also be used for doing any apic model specific
initialisation.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Cyrill Gorcunov <gorcunov@openvz.org>
Cc: steiner@sgi.com
Cc: yinghai@kernel.org
Link: http://lkml.kernel.org/r/20110519234637.247458931@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Code flow for enabling interrupt-remapping has its own routines
for saving and restoring io-apic RTE's. ioapic suspend/resume
code flow also has similar routines. Remove the duplicate code.
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/20110518233157.673130611@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Code flow for enabling interrupt-remapping was
allocating/freeing buffers for saving/restoring io-apic RTE's.
ioapic suspend/resume code uses boot time allocated
ioapic_saved_data that is a perfect match for reuse here.
This will remove the unnecessary allocation/free of the
temporary buffers during suspend/resume of interrupt-remapping
enabled platforms aswell as paving the way for further code
consolidation.
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/20110518233157.574469296@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This allows re-using this buffer for enabling
interrupt-remapping during boot and resume. And thus allow for
consolidating the code between ioapic suspend/resume and
interrupt-remapping.
Tested-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Link: http://lkml.kernel.org/r/20110518233157.481404505@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a potential deadlock when resuming; here the calling
function has disabled interrupts, so we cannot sleep.
Change the memory allocation flag from GFP_KERNEL to GFP_ATOMIC.
TODO: We can do away with this memory allocation during resume
by reusing the ioapic suspend/resume code that uses boot time
allocated buffers, but we want to keep this -stable patch
simple.
Signed-off-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: <stable@kernel.org> # v2.6.38/39
Link: http://lkml.kernel.org/r/20110518233157.385970138@sbsiddha-MOBL3.sc.intel.com
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Stantum devices used to work with MT_CLS_STANTUM but MT_CLS_CONFIDENCE
is exactly the same. This patch switches them to this generic class,
and remove the unused MT_CLS_STANTUM.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for Unitec panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for Touch International panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for GoodTouch panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for CVTouch panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This patch introduce support for ActionStar panels.
This device has not been optimized in term of kernel processing
operations (default class), but it will work.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@enac.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The workaround for Bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=33012
introduced a read and a write to the MC4 mask msr.
Unfortunatly this MSR is not emulated by the KVM hypervisor
so that the kernel will get a #GP and crashes when applying
this workaround when running inside KVM.
This issue was reported as:
https://bugzilla.kernel.org/show_bug.cgi?id=35132
and is fixed with this patch. The change just let the kernel
ignore any #GP it gets while accessing this MSR by using the
_safe msr access methods.
Reported-by: Török Edwin <edwintorok@gmail.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maciej Rutecki <maciej.rutecki@gmail.com>
Cc: Avi Kivity <avi@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org> # .39.x
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are still lots of 80-columns warnings and a few errors
at some tables, but changing them would require more work and
with probably not much gain.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The macro is defined as:
#define CHK_ERROR(s) if( (status = s)<0 ) break
This sucks, as makes harder to debug if something got wrong and
there are more than one level of loops. Also, violates CodingStyle.
Fixed by this simple perl script:
while (<>) { $f.=$_; };
$f=~ s,\n\#define CHK_ERROR[^\n]+\n,\n,;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*\,)\n\s+=\1 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s=(CHK_ERROR\(.*)\s+(\,)\n\s+=\1\2 =g;
$f=~ s,\n(\t+)CHK_ERROR\((.*)\)\;,\n\1status = \2;\n\1if (status < 0)\n\1\tbreak;,g;
print $f;
Plus a few manual adjustments
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This file is big. It has 12000+ lines! Most of the defined stuff aren't
used anyware inside the driver, so we can just remove most of the lines
and still keep everything that have any interest for the driver.
If anyone ever need the other devices, it will be stored at git logs, so
it is easy to recover.
The diff result is impressive:
1 files changed, 1013 insertions(+), 12694 deletions(-)
rewrite drivers/media/dvb/frontends/drxd_map_firm.h (90%)
As a sideback effect, drxd driver will likely compile faster, and
checkpatch.pl can run on this file without taking (literally) hours.
The code cleanup was done using this small script:
$ for i in `perl -ne 'print "$1\n" if (m/define\s+([^\s+]+)/)' drxd_map_firm.h`; do if [ "`grep $i drivers/media/dvb/frontends/drxd*.[ch]`" != "" ] ; then echo $i; fi; done|sort|uniq >used_symbols
$ grep -f used_symbols drxd_map_firm.h >defines
And then deleting the old #define lines, replacing by "defines" file content.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Take a first cleanup pass over the sources to bring them closer to the
Linux coding style.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
