When a default VLAN is added to the VF, the VF driver needs to reset to
pick up the default VLAN ID. We can use the same tx timeout reset logic
to do that, without the debug output. This new function, with the
silent parameter to suppress debug output will now serve both purposes.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PF can setup a default VLAN for a VF. The default VLAN tag is
automatically inserted and stripped without the knowledge of the
stack running on the VF. The VF driver needs to know that default
VLAN is enabled as VLAN acceleration on the RX side is no longer
supported. Call netdev_update_features() to fix up the VLAN features
as necessary. Also, VLAN strip mode must be enabled to strip out
the default VLAN tag.
Only allow VF default VLAN to be set if the firmware spec is >= 1.2.1.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since both CTAG and STAG rx acceleration must be enabled together, we
only need to check one feature flag (NETIF_F_HW_VLAN_CTAG_RX) before
calling __vlan_hwaccel_put_tag().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware can only be set to strip or not strip both the VLAN CTAG and
STAG. It cannot strip one and not strip the other. Add logic to
bnxt_fix_features() to toggle both feature flags when the user is toggling
one of them.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the is_push flag in the software BD before the tx data is pushed to
the chip. It is possible to get the tx interrupt as soon as the tx data
is pushed. The tx handler will not handle the event properly if the
is_push flag is not set and it will crash.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the weaker but more appropriate dma_rmb() to order the reading of
the completion ring.
Suggested-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code is more complicated than necessary and can only report
unsupported SFP+ module if it is plugged in after the device is up.
Rename bnxt_port_module_event() to bnxt_get_port_module_status(). We
already have the current module_status in the link_info structure, so
just check that and report any unsupported SFP+ module status. Delete
the unnecessary last_port_module_event. Call this function at the
end of bnxt_open to report unsupported module already plugged in.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The len value in the hwrm error message is wrong. Use the properly adjusted
value in the variable len.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code has 2 problems:
1. The maximum wait time is not long enough. It is about 60% of the
duration specified by the firmware. It is calling usleep_range(600, 800)
for every 1 msec we are supposed to wait.
2. The granularity of the delay is too coarse. Many simple firmware
commands finish in 25 usec or less.
We fix these 2 issues by multiplying the original 1 msec loop counter by
40 and calling usleep_range(25, 40) for each iteration.
There is also a second delay loop to wait for the last DMA word to
complete. This delay loop should be a very short 5 usec wait.
This change results in much faster bring-up/down time:
Before the patch:
time ip link set p4p1 up
real 0m0.120s
user 0m0.001s
sys 0m0.009s
After the patch:
time ip link set p4p1 up
real 0m0.030s
user 0m0.000s
sys 0m0.010s
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The chip supports 4K/8K/64K page sizes for the rings and we try to
match it to the CPU PAGE_SIZE. The current page size limits for the rings
are based on 4K/8K page size. If the page size is 64K, these limits are
too large. Reduce them appropriately.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add code to log a message during driver load indicating PCIe link
speed and width.
The log message will look like this:
bnxt_en 0000:86:00.0 eth0: PCIe: Speed 8.0GT/s Width x8
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to fetch the SFP EEPROM settings from the firmware
and display it via the ethtool -m command. We support SFP+ and QSFP
modules.
v2: Fixed a bug in bnxt_get_module_eeprom() found by Ben Hutchings.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When there is only 1 MSI-X vector or in INTA mode, tx and rx pre-set
max channel parameters are shown incorrectly in ethtool -l. With only 1
vector, bnxt_get_max_rings() will return -ENOMEM. bnxt_get_channels
should check this return value, and set max_rx/max_tx to 0 if it is
non-zero.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The nf_conntrack_core.c fix in 'net' is not relevant in 'net-next'
because we no longer have a per-netns conntrack hash.
The ip_gre.c conflict as well as the iwlwifi ones were cases of
overlapping changes.
Conflicts:
drivers/net/wireless/intel/iwlwifi/mvm/tx.c
net/ipv4/ip_gre.c
net/netfilter/nf_conntrack_core.c
Signed-off-by: David S. Miller <davem@davemloft.net>
Add detection and recovery code when the hardware returned opaque value
does not match the expected consumer index. Once the issue is detected,
we skip the processing of all RX and LRO/GRO packets. These completion
entries are discarded without sending the SKB to the stack and without
producing new buffers. The function will be reset from a workqueue.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a rare hardware bug that can cause a bad opaque value in the RX
or TPA completion. When this happens, the hardware may have used the
same buffer twice for 2 rx packets. In addition, the driver will also
crash later using the bad opaque as the index into the ring.
The rx opaque value is predictable and is always monotonically increasing.
The workaround is to keep track of the expected next opaque value and
compare it with the one returned by hardware during RX and TPA start
completions. If they miscompare, we will not process any more RX and
TPA completions and exit NAPI. We will then schedule a workqueue to
reset the function.
This patch adds the logic to keep track of the next rx consumer index.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In netdevice.h we removed the structure in net-next that is being
changes in 'net'. In macsec.c and rtnetlink.c we have overlaps
between fixes in 'net' and the u64 attribute changes in 'net-next'.
The mlx5 conflicts have to do with vxlan support dependencies.
Signed-off-by: David S. Miller <davem@davemloft.net>
The multicast/all-multicast internal flags are not properly restored
after device reset. This could lead to unreliable multicast operations
after an ethtool configuration change for example.
Call bnxt_mc_list_updated() and setup the vnic->mask in bnxt_init_chip()
to fix the issue.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code determines if the next ring entry is valid before proceeding
further to read the rest of the entry. The CPU can re-order and read
the rest of the entry first, possibly reading a stale entry, if DMA
of a new entry happens right after reading it. This issue can be
readily seen on a ppc64 system, causing it to crash.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch assumes that the bnxt hardware will ignore existing IPv4/v6
header fields for length and checksum as well as the length and checksum
fields for outer UDP and GRE headers.
I have been told by Michael Chan that this is working. Though this might
be somewhat redundant for IPv6 as they are forcing the checksum to be
computed for all IPv6 frames that are offloaded. A follow-up patch may be
necessary in order to fix this as it is essentially mangling the outer IPv6
headers to add a checksum where none was requested.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
net/ipv4/ip_gre.c
Minor conflicts between tunnel bug fixes in net and
ipv6 tunnel cleanups in net-next.
Signed-off-by: David S. Miller <davem@davemloft.net>
If PAGE_SIZE is bigger than BNXT_RX_PAGE_SIZE, that means the native CPU
page is bigger than the maximum length of the RX BD. Divide the page
into multiple 32K buffers for the aggregation ring.
Add an offset field in the bnxt_sw_rx_agg_bd struct to keep track of the
page offset of each buffer. Since each page can be referenced by multiple
buffer entries, call get_page() as needed to get the proper reference
count.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The RX BD length field of this device is 16-bit, so the largest buffer
size is 65535. For LRO and GRO, we allocate native CPU pages for the
aggregation ring buffers. It won't work if the native CPU page size is
64K or bigger.
We fix this by defining BNXT_RX_PAGE_SIZE to be native CPU page size
up to 32K. Replace PAGE_SIZE with BNXT_RX_PAGE_SIZE in all appropriate
places related to the rx aggregation ring logic.
The next patch will add additional logic to divide the page into 32K
chunks for aggrgation ring buffers if PAGE_SIZE is bigger than
BNXT_RX_PAGE_SIZE.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only MSI-X can be used on a VF. The driver should fail initialization
if it cannot successfully enable MSI-X.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some dual port cards, link speeds on both ports have to be compatible.
Firmware will inform the driver when a certain speed is no longer
supported if the other port has linked up at a certain speed. Add
logic to handle this event by logging a message and getting the
updated list of supported speeds.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some hypervisors (e.g. ESX) require the VF MAC address to be forwarded to
the PF for approval. In Linux PF, the call is not forwarded and the
firmware will simply check and approve the MAC address if the PF has not
previously administered a valid MAC address for this VF.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let firmware know that the driver is giving up control of the link so that
it can be shutdown if no management firmware is running.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
10GBaseT devices must autonegotiate to determine master/slave clocking.
Disallow forced speed in ethtool .set_settings() for these devices.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If autoneg is off, we should always report the speed and duplex settings
even if it is link down so the user knows the current settings. The
unknown speed and duplex should only be used for autoneg when link is
down.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check that the forced speed is a valid speed supported by firmware.
If not supported, return -EINVAL.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the PORT_CONN_NOT_ALLOWED async event handling logic. The driver
will print an appropriate warning to reflect the SFP+ module enforcement
policy done in the firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, the driver only sets bit 0 of the async_event_fwd fields.
To be compatible with the latest spec, we need to set the
appropriate event bits handled by the driver. We should be handling
link change and PF driver unload events, so these 2 bits should be
set.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow users to get|set EEE parameters.
v2: Added comment for preserving the tx_lpi_timer value in get_eee.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Add bnxt_hwrm_set_eee() function to setup EEE firmware parameters based
on the bp->eee settings.
2. The new function bnxt_eee_config_ok() will check if EEE parameters need
to be modified due to autoneg changes.
3. bnxt_hwrm_set_link() has added a new parameter to update EEE. If the
parameter is set, it will call bnxt_hwrm_set_eee().
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get EEE capability and the initial EEE settings from firmware.
Add "EEE is active | not active" to link up dmesg.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the new AUTONEG_PAUSE bit in the new interface to better
control autoneg flow control settings, independent of RX and TX
advertisement settings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use new field names in API structs and stop using deprecated fields
auto_link_speed and auto_duplex in phy_cfg/phy_qcfg structs.
Update copyright year to 2016.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To report flow control tx/rx settings accurately regardless of autoneg
setting, we should use link_info->req_flow_ctrl. Before this patch,
the reported settings were only correct when autoneg was on.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The typo caused the wrong flow control bit to be set.
Reported by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of every padded firmware message is specified in the first
HWRM_VER_GET response message. Use this value to pad every message
after that.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code does the following:
allocate completion ring
initialize completion ring doorbell
disable interrupts on this completion ring by writing to the doorbell
We can have a race where firmware sends an asynchronous event to the host
after completion ring allocation and before doorbell is initialized.
When this happens driver can crash while ringing the doorbell using
uninitialized value as part of handling the IRQ/napi request.
Signed-off-by: Prashant Sreedharan <prashant.sreedharan@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pci_error_handler callbacks to support for pcie advanced error
recovery.
Signed-off-by: Satish Baddipadige <sbaddipa@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include the more useful port statistics in ethtool -S for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Include some of the port error counters (e.g. crc) in ->ndo_get_stats64()
for the PF device.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gather periodic port statistics if the device is PF and link is up. This
is triggered in bnxt_timer() every one second to request firmware to DMA
the counters.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow all autoneg speeds aupported by firmware to be advertised. If
the advertising parameter is 0, then all supported speeds will be
advertised.
Remove BNXT_ALL_COPPER_ETHTOOL_SPEED which is no longer used as all
supported speeds can be advertised.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The supported bits and advertising bits in ethtool have the same
definitions. The same is true for the firmware bits. So use the
common function to handle the conversion for both supported and
advertising bits.
v2: Don't use parentheses on function return.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And report actual pause settings to ETHTOOL_GPAUSEPARAM to let ethtool
resolve the actual pause settings.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
